From: David Gibson <david@gibson.dropbear.id.au>
To: peter.maydell@linaro.org
Cc: agraf@suse.de, groug@kaod.org, mark.cave-ayland@ilande.co.uk,
balaton@eik.bme.hu, qemu-ppc@nongnu.org, qemu-devel@nongnu.org,
David Gibson <david@gibson.dropbear.id.au>
Subject: [Qemu-devel] [PULL 16/26] macio: convert pmac_ide_ops from old_mmio
Date: Wed, 27 Sep 2017 17:43:06 +1000 [thread overview]
Message-ID: <20170927074316.4454-17-david@gibson.dropbear.id.au> (raw)
In-Reply-To: <20170927074316.4454-1-david@gibson.dropbear.id.au>
From: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
---
hw/ide/macio.c | 181 ++++++++++++++++++++++++---------------------------------
1 file changed, 75 insertions(+), 106 deletions(-)
diff --git a/hw/ide/macio.c b/hw/ide/macio.c
index db5db390e7..18ae952934 100644
--- a/hw/ide/macio.c
+++ b/hw/ide/macio.c
@@ -255,131 +255,100 @@ static void pmac_ide_flush(DBDMA_io *io)
}
/* PowerMac IDE memory IO */
-static void pmac_ide_writeb (void *opaque,
- hwaddr addr, uint32_t val)
+static uint64_t pmac_ide_read(void *opaque, hwaddr addr, unsigned size)
{
MACIOIDEState *d = opaque;
-
- addr = (addr & 0xFFF) >> 4;
- switch (addr) {
- case 1 ... 7:
- ide_ioport_write(&d->bus, addr, val);
- break;
- case 8:
- case 22:
- ide_cmd_write(&d->bus, 0, val);
+ uint64_t retval = 0xffffffff;
+ int reg = addr >> 4;
+
+ switch (reg) {
+ case 0x0:
+ if (size == 2) {
+ retval = ide_data_readw(&d->bus, 0);
+ } else if (size == 4) {
+ retval = ide_data_readl(&d->bus, 0);
+ }
break;
- default:
+ case 0x1 ... 0x7:
+ if (size == 1) {
+ retval = ide_ioport_read(&d->bus, reg);
+ }
break;
- }
-}
-
-static uint32_t pmac_ide_readb (void *opaque,hwaddr addr)
-{
- uint8_t retval;
- MACIOIDEState *d = opaque;
-
- addr = (addr & 0xFFF) >> 4;
- switch (addr) {
- case 1 ... 7:
- retval = ide_ioport_read(&d->bus, addr);
+ case 0x8:
+ case 0x16:
+ if (size == 1) {
+ retval = ide_status_read(&d->bus, 0);
+ }
break;
- case 8:
- case 22:
- retval = ide_status_read(&d->bus, 0);
+ case 0x20:
+ if (size == 4) {
+ retval = d->timing_reg;
+ }
break;
- default:
- retval = 0xFF;
+ case 0x30:
+ /* This is an interrupt state register that only exists
+ * in the KeyLargo and later variants. Bit 0x8000_0000
+ * latches the DMA interrupt and has to be written to
+ * clear. Bit 0x4000_0000 is an image of the disk
+ * interrupt. MacOS X relies on this and will hang if
+ * we don't provide at least the disk interrupt
+ */
+ if (size == 4) {
+ retval = d->irq_reg;
+ }
break;
}
- return retval;
-}
-static void pmac_ide_writew (void *opaque,
- hwaddr addr, uint32_t val)
-{
- MACIOIDEState *d = opaque;
-
- addr = (addr & 0xFFF) >> 4;
- val = bswap16(val);
- if (addr == 0) {
- ide_data_writew(&d->bus, 0, val);
- }
-}
-
-static uint32_t pmac_ide_readw (void *opaque,hwaddr addr)
-{
- uint16_t retval;
- MACIOIDEState *d = opaque;
-
- addr = (addr & 0xFFF) >> 4;
- if (addr == 0) {
- retval = ide_data_readw(&d->bus, 0);
- } else {
- retval = 0xFFFF;
- }
- retval = bswap16(retval);
return retval;
}
-static void pmac_ide_writel (void *opaque,
- hwaddr addr, uint32_t val)
-{
- MACIOIDEState *d = opaque;
- addr = (addr & 0xFFF) >> 4;
- val = bswap32(val);
- if (addr == 0) {
- ide_data_writel(&d->bus, 0, val);
- } else if (addr == 0x20) {
- d->timing_reg = val;
- } else if (addr == 0x30) {
- if (val & 0x80000000u) {
- d->irq_reg &= 0x7fffffff;
- }
- }
-}
-
-static uint32_t pmac_ide_readl (void *opaque,hwaddr addr)
+static void pmac_ide_write(void *opaque, hwaddr addr, uint64_t val,
+ unsigned size)
{
- uint32_t retval;
MACIOIDEState *d = opaque;
-
- addr = (addr & 0xFFF) >> 4;
- if (addr == 0) {
- retval = ide_data_readl(&d->bus, 0);
- } else if (addr == 0x20) {
- retval = d->timing_reg;
- } else if (addr == 0x30) {
- /* This is an interrupt state register that only exists
- * in the KeyLargo and later variants. Bit 0x8000_0000
- * latches the DMA interrupt and has to be written to
- * clear. Bit 0x4000_0000 is an image of the disk
- * interrupt. MacOS X relies on this and will hang if
- * we don't provide at least the disk interrupt
- */
- retval = d->irq_reg;
- } else {
- retval = 0xFFFFFFFF;
+ int reg = addr >> 4;
+
+ switch (reg) {
+ case 0x0:
+ if (size == 2) {
+ ide_data_writew(&d->bus, 0, val);
+ } else if (size == 4) {
+ ide_data_writel(&d->bus, 0, val);
+ }
+ break;
+ case 0x1 ... 0x7:
+ if (size == 1) {
+ ide_ioport_write(&d->bus, reg, val);
+ }
+ break;
+ case 0x8:
+ case 0x16:
+ if (size == 1) {
+ ide_cmd_write(&d->bus, 0, val);
+ }
+ break;
+ case 0x20:
+ if (size == 4) {
+ d->timing_reg = val;
+ }
+ break;
+ case 0x30:
+ if (size == 4) {
+ if (val & 0x80000000u) {
+ d->irq_reg &= 0x7fffffff;
+ }
+ }
+ break;
}
- retval = bswap32(retval);
- return retval;
}
static const MemoryRegionOps pmac_ide_ops = {
- .old_mmio = {
- .write = {
- pmac_ide_writeb,
- pmac_ide_writew,
- pmac_ide_writel,
- },
- .read = {
- pmac_ide_readb,
- pmac_ide_readw,
- pmac_ide_readl,
- },
- },
- .endianness = DEVICE_NATIVE_ENDIAN,
+ .read = pmac_ide_read,
+ .write = pmac_ide_write,
+ .valid.min_access_size = 1,
+ .valid.max_access_size = 4,
+ .endianness = DEVICE_LITTLE_ENDIAN,
};
static const VMStateDescription vmstate_pmac = {
--
2.13.5
next prev parent reply other threads:[~2017-09-27 7:43 UTC|newest]
Thread overview: 28+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-09-27 7:42 [Qemu-devel] [PULL 00/26] ppc-for-2.11 queue 20170927 David Gibson
2017-09-27 7:42 ` [Qemu-devel] [PULL 01/26] ppc/kvm: check some capabilities with kvm_vm_check_extension() David Gibson
2017-09-27 7:42 ` [Qemu-devel] [PULL 02/26] ppc/kvm: drop kvmppc_has_cap_htab_fd() David Gibson
2017-09-27 7:42 ` [Qemu-devel] [PULL 03/26] ohci: Allow sysbus version to be used as a companion David Gibson
2017-09-27 7:42 ` [Qemu-devel] [PULL 04/26] ehci: Add ppc4xx-ehci for the USB 2.0 controller in embedded PPC SoCs David Gibson
2017-09-27 7:42 ` [Qemu-devel] [PULL 05/26] ppc: Add 460EX embedded CPU David Gibson
2017-09-27 7:42 ` [Qemu-devel] [PULL 06/26] ppc4xx: Add more PLB registers David Gibson
2017-09-27 7:42 ` [Qemu-devel] [PULL 07/26] ppc: QOMify g3beige machine David Gibson
2017-09-27 7:42 ` [Qemu-devel] [PULL 08/26] ppc/mac: Advertise a high clock frequency for NewWorld Macs David Gibson
2017-09-27 7:42 ` [Qemu-devel] [PULL 09/26] ppc/mac: More rework of the DBDMA emulation David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 10/26] ppc/ide/macio: Add missing registers David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 11/26] ppc: Fix OpenPIC model David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 12/26] ppc/kvm: change kvmppc_get_htab_fd() to return -errno on error David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 13/26] ppc/kvm: generalize the use of kvmppc_get_htab_fd() David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 14/26] spapr: introduce helpers to migrate HPT chunks and the end marker David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 15/26] ppc/pnv: Improve macro parenthesization David Gibson
2017-09-27 7:43 ` David Gibson [this message]
2017-09-27 7:43 ` [Qemu-devel] [PULL 17/26] spapr_pci: make index property mandatory David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 18/26] ppc: remove unused CPU definitions David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 19/26] ppc: remove all " David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 20/26] ppc/pnv: check for OPAL firmware file presence David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 21/26] spapr: fix the value of SDR1 in kvmppc_put_books_sregs() David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 22/26] mac_dbdma: remove unused IO fields from DBDMAState David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 23/26] mac_dbdma: QOMify David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 24/26] mac_dbdma: remove DBDMA_init() function David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 25/26] macio: pass channel into MACIOIDEState via qdev property David Gibson
2017-09-27 7:43 ` [Qemu-devel] [PULL 26/26] macio: use object link between MACIO_IDE and MAC_DBDMA object David Gibson
2017-09-27 21:43 ` [Qemu-devel] [PULL 00/26] ppc-for-2.11 queue 20170927 Peter Maydell
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170927074316.4454-17-david@gibson.dropbear.id.au \
--to=david@gibson.dropbear.id.au \
--cc=agraf@suse.de \
--cc=balaton@eik.bme.hu \
--cc=groug@kaod.org \
--cc=mark.cave-ayland@ilande.co.uk \
--cc=peter.maydell@linaro.org \
--cc=qemu-devel@nongnu.org \
--cc=qemu-ppc@nongnu.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).