qemu-devel.nongnu.org archive mirror
 help / color / mirror / Atom feed
From: David Gibson <david@gibson.dropbear.id.au>
To: peter.maydell@linaro.org
Cc: surajjs@au1.ibm.com, groug@kaod.org, mdroth@linux.vnet.ibm.com,
	qemu-ppc@nongnu.org, qemu-devel@nongnu.org,
	BALATON Zoltan <balaton@eik.bme.hu>,
	David Gibson <david@gibson.dropbear.id.au>
Subject: [Qemu-devel] [PULL 04/12] sm501: Add some more unimplemented registers
Date: Mon,  8 Jan 2018 16:53:40 +1100	[thread overview]
Message-ID: <20180108055348.20444-5-david@gibson.dropbear.id.au> (raw)
In-Reply-To: <20180108055348.20444-1-david@gibson.dropbear.id.au>

From: BALATON Zoltan <balaton@eik.bme.hu>

These are not really implemented (just return zero or default values)
but add these so guests accessing them can run.

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
---
 hw/display/sm501.c | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/hw/display/sm501.c b/hw/display/sm501.c
index b9b611131e..4f7dc59b25 100644
--- a/hw/display/sm501.c
+++ b/hw/display/sm501.c
@@ -795,6 +795,8 @@ static uint64_t sm501_system_config_read(void *opaque, hwaddr addr,
     case SM501_ARBTRTN_CONTROL:
         ret = s->arbitration_control;
         break;
+    case SM501_COMMAND_LIST_STATUS:
+        ret = 0x00180002; /* FIFOs are empty, everything idle */
     case SM501_IRQ_MASK:
         ret = s->irq_mask;
         break;
@@ -812,6 +814,9 @@ static uint64_t sm501_system_config_read(void *opaque, hwaddr addr,
     case SM501_POWER_MODE_CONTROL:
         ret = s->power_mode_control;
         break;
+    case SM501_ENDIAN_CONTROL:
+        ret = 0; /* Only default little endian mode is supported */
+        break;
 
     default:
         printf("sm501 system config : not implemented register read."
@@ -865,6 +870,12 @@ static void sm501_system_config_write(void *opaque, hwaddr addr,
     case SM501_POWER_MODE_CONTROL:
         s->power_mode_control = value & 0x00000003;
         break;
+    case SM501_ENDIAN_CONTROL:
+        if (value & 0x00000001) {
+            printf("sm501 system config : big endian mode not implemented.\n");
+            abort();
+        }
+        break;
 
     default:
         printf("sm501 system config : not implemented register write."
@@ -924,6 +935,9 @@ static uint64_t sm501_disp_ctrl_read(void *opaque, hwaddr addr,
     case SM501_DC_PANEL_PANNING_CONTROL:
         ret = s->dc_panel_panning_control;
         break;
+    case SM501_DC_PANEL_COLOR_KEY:
+        /* Not implemented yet */
+        break;
     case SM501_DC_PANEL_FB_ADDR:
         ret = s->dc_panel_fb_addr;
         break;
@@ -1035,6 +1049,9 @@ static void sm501_disp_ctrl_write(void *opaque, hwaddr addr,
     case SM501_DC_PANEL_PANNING_CONTROL:
         s->dc_panel_panning_control = value & 0xFF3FFF3F;
         break;
+    case SM501_DC_PANEL_COLOR_KEY:
+        /* Not implemented yet */
+        break;
     case SM501_DC_PANEL_FB_ADDR:
         s->dc_panel_fb_addr = value & 0x8FFFFFF0;
         break;
-- 
2.14.3

  parent reply	other threads:[~2018-01-08  5:54 UTC|newest]

Thread overview: 29+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-01-08  5:53 [Qemu-devel] [PULL 00/12] ppc-for-2.12 queue 20180108 David Gibson
2018-01-08  5:53 ` [Qemu-devel] [PULL 01/12] target-ppc: optimize cmp translation David Gibson
2018-01-18 16:36   ` Paolo Bonzini
2018-01-18 23:28     ` David Gibson
2018-01-08  5:53 ` [Qemu-devel] [PULL 02/12] pseries: Update SLOF firmware image to qemu-slof-20171214 David Gibson
2018-01-08  5:53 ` [Qemu-devel] [PULL 03/12] sm501: Add panel hardware cursor registers also to read function David Gibson
2018-01-08  5:53 ` David Gibson [this message]
2018-01-08  5:53 ` [Qemu-devel] [PULL 05/12] ppc4xx_i2c: Implement basic I2C functions David Gibson
2018-01-08  5:53 ` [Qemu-devel] [PULL 06/12] spapr_pci: use warn_report() David Gibson
2018-01-08  5:53 ` [Qemu-devel] [PULL 07/12] hw/ide: Emulate SiI3112 SATA controller David Gibson
2018-01-08  5:53 ` [Qemu-devel] [PULL 08/12] ppc/pnv: change powernv_ prefix to pnv_ for overall naming consistency David Gibson
2018-01-08  5:53 ` [Qemu-devel] [PULL 09/12] target/ppc: more use of the PPC_*() macros David Gibson
2018-01-08  5:53 ` [Qemu-devel] [PULL 10/12] Update dtc to fix compilation problem on Mac OS 10.6 David Gibson
2018-01-08  5:53 ` [Qemu-devel] [PULL 11/12] hw/ppc: Remove the deprecated spapr-pci-vfio-host-bridge device David Gibson
2018-01-08  5:53 ` [Qemu-devel] [PULL 12/12] spapr: Correct compatibility mode setting for hotplugged CPUs David Gibson
2018-01-09 11:46 ` [Qemu-devel] [PULL 00/12] ppc-for-2.12 queue 20180108 Peter Maydell
2018-01-09 12:16   ` David Gibson
2018-01-09 15:15     ` Peter Maydell
2018-01-09 16:02       ` Michael Roth
2018-01-09 17:34         ` Paolo Bonzini
2018-01-09 17:57           ` Michael Roth
2018-01-10  0:41       ` Richard Henderson
2018-01-10  1:55       ` David Gibson
2018-01-10 13:33         ` Paolo Bonzini
2018-01-11  2:47           ` David Gibson
2018-01-11 14:18             ` Richard Henderson
2018-01-10 10:37     ` [Qemu-devel] [Qemu-ppc] " luigi burdo
2018-01-10 10:41       ` Peter Maydell
2018-01-10 16:02         ` luigi burdo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180108055348.20444-5-david@gibson.dropbear.id.au \
    --to=david@gibson.dropbear.id.au \
    --cc=balaton@eik.bme.hu \
    --cc=groug@kaod.org \
    --cc=mdroth@linux.vnet.ibm.com \
    --cc=peter.maydell@linaro.org \
    --cc=qemu-devel@nongnu.org \
    --cc=qemu-ppc@nongnu.org \
    --cc=surajjs@au1.ibm.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).