From: Richard Henderson <richard.henderson@linaro.org>
To: qemu-devel@nongnu.org
Cc: peter.maydell@linaro.org
Subject: [Qemu-devel] [PULL 10/43] target/hppa: Adjust insn mask for mfctl, w
Date: Sun, 21 Jan 2018 19:41:44 -0800 [thread overview]
Message-ID: <20180122034217.19593-11-richard.henderson@linaro.org> (raw)
In-Reply-To: <20180122034217.19593-1-richard.henderson@linaro.org>
While the E bit is only used for pa2.0 mfctl,w from sar,
the otherwise reserved bit does not appear to be decoded.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
---
target/hppa/translate.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/target/hppa/translate.c b/target/hppa/translate.c
index 0408dbedf1..b201e5ace2 100644
--- a/target/hppa/translate.c
+++ b/target/hppa/translate.c
@@ -2151,7 +2151,7 @@ static const DisasInsn table_system[] = {
{ 0x016018c0u, 0xffe0ffffu, trans_mtsarcm },
{ 0x000014a0u, 0xffffffe0u, trans_mfia },
{ 0x000004a0u, 0xffff1fe0u, trans_mfsp },
- { 0x000008a0u, 0xfc1fffe0u, trans_mfctl },
+ { 0x000008a0u, 0xfc1fbfe0u, trans_mfctl },
{ 0x00000400u, 0xffffffffu, trans_sync },
{ 0x000010a0u, 0xfc1f3fe0u, trans_ldsid },
#ifndef CONFIG_USER_ONLY
--
2.14.3
next prev parent reply other threads:[~2018-01-22 3:42 UTC|newest]
Thread overview: 48+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-22 3:41 [Qemu-devel] [PULL 00/43] Add hppa-softmmu Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 01/43] target/hppa: Skeleton support for hppa-softmmu Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 02/43] target/hppa: Define the rest of the PSW Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 03/43] target/hppa: Disable gateway page emulation for system mode Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 04/43] target/hppa: Define hardware exception types Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 05/43] target/hppa: Split address size from register size Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 06/43] target/hppa: Implement mmu_idx from IA privilege level Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 07/43] target/hppa: Implement the system mask instructions Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 08/43] target/hppa: Add space registers Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 09/43] target/hppa: Add control registers Richard Henderson
2018-01-22 3:41 ` Richard Henderson [this message]
2018-01-22 3:41 ` [Qemu-devel] [PULL 11/43] target/hppa: Implement rfi Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 12/43] target/hppa: Fill in hppa_cpu_do_interrupt/hppa_cpu_exec_interrupt Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 13/43] target/hppa: Implement unaligned access trap Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 14/43] target/hppa: Use space registers in data operations Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 15/43] target/hppa: Avoid privilege level decrease during branches Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 16/43] target/hppa: Implement IASQ Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 17/43] target/hppa: Implement tlb_fill Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 18/43] target/hppa: Implement external interrupts Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 19/43] target/hppa: Implement the interval timer Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 20/43] target/hppa: Log unimplemented instructions Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 21/43] target/hppa: Implement I*TLBA and I*TLBP insns Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 22/43] target/hppa: Implement P*TLB and P*TLBE insns Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 23/43] target/hppa: Implement LDWA Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 24/43] target/hppa: Implement LPA Richard Henderson
2018-01-22 3:41 ` [Qemu-devel] [PULL 25/43] target/hppa: Implement LCI Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 26/43] target/hppa: Implement SYNCDMA insn Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 27/43] target/hppa: Implement halt and reset instructions Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 28/43] target/hppa: Optimize for flat addressing space Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 29/43] target/hppa: Add system registers to gdbstub Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 30/43] target/hppa: Add migration for the cpu Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 31/43] target/hppa: Implement B,GATE insn Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 32/43] target/hppa: Only use EXCP_DTLB_MISS Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 33/43] qom: Add MMU_DEBUG_LOAD Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 34/43] target/hppa: Use MMU_DEBUG_LOAD when reloading for CR[IIR] Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 35/43] target/hppa: Increase number of temp regs Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 36/43] target/hppa: Fix comment Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 37/43] target/hppa: Implement LDSID for system mode Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 38/43] target/hppa: Implement a pause instruction Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 39/43] target/hppa: Implement STWA Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 40/43] target/hppa: Enable MTTCG Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 41/43] hw/hppa: Implement DINO system board Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 42/43] pc-bios: Add hppa-firmware.img and git submodule Richard Henderson
2018-01-22 3:42 ` [Qemu-devel] [PULL 43/43] hw/hppa: Add MAINTAINERS entry Richard Henderson
2018-01-22 4:27 ` [Qemu-devel] [PULL 00/43] Add hppa-softmmu no-reply
2018-01-22 4:38 ` no-reply
2018-01-22 4:57 ` no-reply
2018-01-23 10:14 ` Peter Maydell
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180122034217.19593-11-richard.henderson@linaro.org \
--to=richard.henderson@linaro.org \
--cc=peter.maydell@linaro.org \
--cc=qemu-devel@nongnu.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).