From: Peter Maydell <peter.maydell@linaro.org>
To: qemu-arm@nongnu.org, qemu-devel@nongnu.org
Cc: patches@linaro.org
Subject: [Qemu-devel] [PATCH 05/13] target/arm: Add some comments in Thumb decode
Date: Tue, 2 Oct 2018 17:35:48 +0100 [thread overview]
Message-ID: <20181002163556.10279-6-peter.maydell@linaro.org> (raw)
In-Reply-To: <20181002163556.10279-1-peter.maydell@linaro.org>
Add some comments to the Thumb decoder indicating what bits
of the instruction have been decoded at various points in
the code.
This is not an exhaustive set of comments; we're gradually
adding comments as we work with particular bits of the code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
---
Specifically, I figured these out as I was going through looking
for the insns which write SP. These comments turn out not to
be relevant to those instructions, but I don't want to throw
them away.
---
target/arm/translate.c | 20 +++++++++++++++++---
1 file changed, 17 insertions(+), 3 deletions(-)
diff --git a/target/arm/translate.c b/target/arm/translate.c
index 25a8fe672f5..fcb33b8a503 100644
--- a/target/arm/translate.c
+++ b/target/arm/translate.c
@@ -10623,6 +10623,10 @@ static void disas_thumb2_insn(DisasContext *s, uint32_t insn)
tmp2 = load_reg(s, rm);
if ((insn & 0x70) != 0)
goto illegal_op;
+ /*
+ * 0b1111_1010_0xxx_xxxx_1111_xxxx_0000_xxxx:
+ * - MOV, MOVS (register-shifted register), flagsetting
+ */
op = (insn >> 21) & 3;
logic_cc = (insn & (1 << 20)) != 0;
gen_arm_shift_reg(tmp, op, tmp2, logic_cc);
@@ -11674,7 +11678,11 @@ static void disas_thumb_insn(DisasContext *s, uint32_t insn)
rd = insn & 7;
op = (insn >> 11) & 3;
if (op == 3) {
- /* add/subtract */
+ /*
+ * 0b0001_1xxx_xxxx_xxxx
+ * - Add, subtract (three low registers)
+ * - Add, subtract (two low registers and immediate)
+ */
rn = (insn >> 3) & 7;
tmp = load_reg(s, rn);
if (insn & (1 << 10)) {
@@ -11711,7 +11719,10 @@ static void disas_thumb_insn(DisasContext *s, uint32_t insn)
}
break;
case 2: case 3:
- /* arithmetic large immediate */
+ /*
+ * 0b001x_xxxx_xxxx_xxxx
+ * - Add, subtract, compare, move (one low register and immediate)
+ */
op = (insn >> 11) & 3;
rd = (insn >> 8) & 0x7;
if (op == 0) { /* mov */
@@ -11848,7 +11859,10 @@ static void disas_thumb_insn(DisasContext *s, uint32_t insn)
break;
}
- /* data processing register */
+ /*
+ * 0b0100_00xx_xxxx_xxxx
+ * - Data-processing (two low registers)
+ */
rd = insn & 7;
rm = (insn >> 3) & 7;
op = (insn >> 6) & 0xf;
--
2.19.0
next prev parent reply other threads:[~2018-10-02 16:36 UTC|newest]
Thread overview: 40+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-02 16:35 [Qemu-devel] [PATCH 00/13] target/arm: Implement v8M stack limit checks Peter Maydell
2018-10-02 16:35 ` [Qemu-devel] [PATCH 01/13] target/arm: Define new TBFLAG for v8M stack checking Peter Maydell
2018-10-03 19:51 ` Richard Henderson
2018-10-04 16:02 ` Philippe Mathieu-Daudé
2018-10-02 16:35 ` [Qemu-devel] [PATCH 02/13] target/arm: Define new EXCP type for v8M stack overflows Peter Maydell
2018-10-03 8:52 ` Philippe Mathieu-Daudé
2018-10-03 19:52 ` Richard Henderson
2018-10-02 16:35 ` [Qemu-devel] [PATCH 03/13] target/arm: Move v7m_using_psp() to internals.h Peter Maydell
2018-10-03 8:52 ` Philippe Mathieu-Daudé
2018-10-03 19:53 ` Richard Henderson
2018-10-02 16:35 ` [Qemu-devel] [PATCH 04/13] target/arm: Add v8M stack checks on ADD/SUB/MOV of SP Peter Maydell
2018-10-03 20:00 ` Richard Henderson
2018-10-02 16:35 ` Peter Maydell [this message]
2018-10-03 10:32 ` [Qemu-devel] [PATCH 05/13] target/arm: Add some comments in Thumb decode Philippe Mathieu-Daudé
2018-10-03 20:02 ` Richard Henderson
2018-10-02 16:35 ` [Qemu-devel] [PATCH 06/13] target/arm: Add v8M stack checks on exception entry Peter Maydell
2018-10-03 8:58 ` Philippe Mathieu-Daudé
2018-10-03 20:12 ` Richard Henderson
2018-10-02 16:35 ` [Qemu-devel] [PATCH 07/13] target/arm: Add v8M stack limit checks on NS function calls Peter Maydell
2018-10-03 9:02 ` Philippe Mathieu-Daudé
2018-10-03 20:14 ` Richard Henderson
2018-10-02 16:35 ` [Qemu-devel] [PATCH 08/13] target/arm: Add v8M stack checks for LDRD/STRD (imm) Peter Maydell
2018-10-03 14:38 ` Philippe Mathieu-Daudé
2018-10-03 20:16 ` Richard Henderson
2018-10-02 16:35 ` [Qemu-devel] [PATCH 09/13] target/arm: Add v8M stack checks for Thumb2 LDM/STM Peter Maydell
2018-10-03 9:08 ` Philippe Mathieu-Daudé
2018-10-03 20:17 ` Richard Henderson
2018-10-02 16:35 ` [Qemu-devel] [PATCH 10/13] target/arm: Add v8M stack checks for T32 load/store single Peter Maydell
2018-10-03 10:44 ` Philippe Mathieu-Daudé
2018-10-03 20:18 ` Richard Henderson
2018-10-02 16:35 ` [Qemu-devel] [PATCH 11/13] target/arm: Add v8M stack checks for Thumb push/pop Peter Maydell
2018-10-03 9:20 ` Philippe Mathieu-Daudé
2018-10-03 20:19 ` Richard Henderson
2018-10-02 16:35 ` [Qemu-devel] [PATCH 12/13] target/arm: Add v8M stack checks for VLDM/VSTM Peter Maydell
2018-10-03 9:55 ` Philippe Mathieu-Daudé
2018-10-03 20:20 ` Richard Henderson
2018-10-03 20:21 ` Richard Henderson
2018-10-02 16:35 ` [Qemu-devel] [PATCH 13/13] target/arm: Add v8M stack checks for MSR to SP_NS Peter Maydell
2018-10-03 10:18 ` Philippe Mathieu-Daudé
2018-10-03 20:22 ` Richard Henderson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181002163556.10279-6-peter.maydell@linaro.org \
--to=peter.maydell@linaro.org \
--cc=patches@linaro.org \
--cc=qemu-arm@nongnu.org \
--cc=qemu-devel@nongnu.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).