Re: [PATCH v5 2/2] hw/block: m25p80: Implement AAI-WP command support for SST flashes

[Francisco Iglesias <frasse.iglesias@gmail.com>]

On [2020 Dec 23] Wed 10:00:25, Bin Meng wrote:
> From: Xuzhou Cheng <xuzhou.cheng@windriver.com>
> 
> Auto Address Increment (AAI) Word-Program is a special command of
> SST flashes. AAI-WP allows multiple bytes of data to be programmed
> without re-issuing the next sequential address location.
> 
> Signed-off-by: Xuzhou Cheng <xuzhou.cheng@windriver.com>
> Signed-off-by: Bin Meng <bin.meng@windriver.com>

Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>

> 
> ---
> 
> Changes in v5:
> - remove the guest error logging when address wrap is detected in AAI
> - change to return s->aai_enable in m25p80_aai_enable_needed()
> 
> Changes in v4:
> - simplify is_valid_aai_cmd()
> - use a subsection for s->aai_enable vm state
> 
> Changes in v3:
> - initialize aai_enable to false in reset_memory()
> 
> Changes in v2:
> - add aai_enable into the vmstate
> - validate AAI command before decoding a new command
> - log guest errors during AAI_WP command handling
> - report AAI status in the status register
> - abort AAI programming when address is wrapped
> - make sure AAI programming starts from the even address
> 
>  hw/block/m25p80.c | 73 +++++++++++++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 73 insertions(+)
> 
> diff --git a/hw/block/m25p80.c b/hw/block/m25p80.c
> index 29598b4..c64852f 100644
> --- a/hw/block/m25p80.c
> +++ b/hw/block/m25p80.c
> @@ -359,6 +359,7 @@ typedef enum {
>      QPP_4 = 0x34,
>      RDID_90 = 0x90,
>      RDID_AB = 0xab,
> +    AAI_WP = 0xad,
>  
>      ERASE_4K = 0x20,
>      ERASE4_4K = 0x21,
> @@ -455,6 +456,7 @@ struct Flash {
>      bool four_bytes_address_mode;
>      bool reset_enable;
>      bool quad_enable;
> +    bool aai_enable;
>      uint8_t ear;
>  
>      int64_t dirty_page;
> @@ -670,6 +672,11 @@ static void complete_collecting_data(Flash *s)
>      case PP4_4:
>          s->state = STATE_PAGE_PROGRAM;
>          break;
> +    case AAI_WP:
> +        /* AAI programming starts from the even address */
> +        s->cur_addr &= ~BIT(0);
> +        s->state = STATE_PAGE_PROGRAM;
> +        break;
>      case READ:
>      case READ4:
>      case FAST_READ:
> @@ -768,6 +775,7 @@ static void reset_memory(Flash *s)
>      s->write_enable = false;
>      s->reset_enable = false;
>      s->quad_enable = false;
> +    s->aai_enable = false;
>  
>      switch (get_man(s)) {
>      case MAN_NUMONYX:
> @@ -973,6 +981,11 @@ static void decode_qio_read_cmd(Flash *s)
>      s->state = STATE_COLLECTING_DATA;
>  }
>  
> +static bool is_valid_aai_cmd(uint32_t cmd)
> +{
> +    return cmd == AAI_WP || cmd == WRDI || cmd == RDSR;
> +}
> +
>  static void decode_new_cmd(Flash *s, uint32_t value)
>  {
>      int i;
> @@ -984,6 +997,11 @@ static void decode_new_cmd(Flash *s, uint32_t value)
>          s->reset_enable = false;
>      }
>  
> +    if (get_man(s) == MAN_SST && s->aai_enable && !is_valid_aai_cmd(value)) {
> +        qemu_log_mask(LOG_GUEST_ERROR,
> +                      "M25P80: Invalid cmd within AAI programming sequence");
> +    }
> +
>      switch (value) {
>  
>      case ERASE_4K:
> @@ -1103,6 +1121,9 @@ static void decode_new_cmd(Flash *s, uint32_t value)
>  
>      case WRDI:
>          s->write_enable = false;
> +        if (get_man(s) == MAN_SST) {
> +            s->aai_enable = false;
> +        }
>          break;
>      case WREN:
>          s->write_enable = true;
> @@ -1113,6 +1134,10 @@ static void decode_new_cmd(Flash *s, uint32_t value)
>          if (get_man(s) == MAN_MACRONIX) {
>              s->data[0] |= (!!s->quad_enable) << 6;
>          }
> +        if (get_man(s) == MAN_SST) {
> +            s->data[0] |= (!!s->aai_enable) << 6;
> +        }
> +
>          s->pos = 0;
>          s->len = 1;
>          s->data_read_loop = true;
> @@ -1260,6 +1285,24 @@ static void decode_new_cmd(Flash *s, uint32_t value)
>      case RSTQIO:
>          s->quad_enable = false;
>          break;
> +    case AAI_WP:
> +        if (get_man(s) == MAN_SST) {
> +            if (s->write_enable) {
> +                if (s->aai_enable) {
> +                    s->state = STATE_PAGE_PROGRAM;
> +                } else {
> +                    s->aai_enable = true;
> +                    s->needed_bytes = get_addr_length(s);
> +                    s->state = STATE_COLLECTING_DATA;
> +                }
> +            } else {
> +                qemu_log_mask(LOG_GUEST_ERROR,
> +                              "M25P80: AAI_WP with write protect\n");
> +            }
> +        } else {
> +            qemu_log_mask(LOG_GUEST_ERROR, "M25P80: Unknown cmd %x\n", value);
> +        }
> +        break;
>      default:
>          s->pos = 0;
>          s->len = 1;
> @@ -1305,6 +1348,17 @@ static uint32_t m25p80_transfer8(SSIPeripheral *ss, uint32_t tx)
>          trace_m25p80_page_program(s, s->cur_addr, (uint8_t)tx);
>          flash_write8(s, s->cur_addr, (uint8_t)tx);
>          s->cur_addr = (s->cur_addr + 1) & (s->size - 1);
> +
> +        if (get_man(s) == MAN_SST && s->aai_enable && s->cur_addr == 0) {
> +            /*
> +             * There is no wrap mode during AAI programming once the highest
> +             * unprotected memory address is reached. The Write-Enable-Latch
> +             * bit is automatically reset, and AAI programming mode aborts.
> +             */
> +            s->write_enable = false;
> +            s->aai_enable = false;
> +        }
> +
>          break;
>  
>      case STATE_READ:
> @@ -1450,6 +1504,24 @@ static const VMStateDescription vmstate_m25p80_data_read_loop = {
>      }
>  };
>  
> +static bool m25p80_aai_enable_needed(void *opaque)
> +{
> +    Flash *s = (Flash *)opaque;
> +
> +    return s->aai_enable;
> +}
> +
> +static const VMStateDescription vmstate_m25p80_aai_enable = {
> +    .name = "m25p80/aai_enable",
> +    .version_id = 1,
> +    .minimum_version_id = 1,
> +    .needed = m25p80_aai_enable_needed,
> +    .fields = (VMStateField[]) {
> +        VMSTATE_BOOL(aai_enable, Flash),
> +        VMSTATE_END_OF_LIST()
> +    }
> +};
> +
>  static const VMStateDescription vmstate_m25p80 = {
>      .name = "m25p80",
>      .version_id = 0,
> @@ -1480,6 +1552,7 @@ static const VMStateDescription vmstate_m25p80 = {
>      },
>      .subsections = (const VMStateDescription * []) {
>          &vmstate_m25p80_data_read_loop,
> +        &vmstate_m25p80_aai_enable,
>          NULL
>      }
>  };
> -- 
> 2.7.4
>