* [PULL 01/18] aspeed/smc: Add watchdog Control/Status Registers
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 02/18] aspeed/smc: Introduce aspeed_smc_error() helper Cédric Le Goater
` (17 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, qemu-devel, qemu-arm, Cédric Le Goater,
Peter Delevoryas, Joel Stanley
The Aspeed SoCs have a dual boot function for firmware fail-over
recovery. The system auto-reboots from the second flash if the main
flash does not boot successfully within a certain amount of time. This
function is called alternate boot (ABR) in the FMC controllers.
On AST2400/AST2500, ABR is enabled by hardware strapping in SCU70 to
enable the 2nd watchdog timer, on AST2600, through register SCU510.
If the boot on the the main flash succeeds, the firmware should
disable the 2nd watchdog timer. If not, the BMC is reset and the CE0
and CE1 mappings are swapped to restart the BMC from the 2nd flash.
On the AST2600, the ABR registers controlling the 2nd watchdog timer
were moved from the watchdog register to the FMC controller and the
FMC model should be able to control WDT2 through its own register set.
This requires more work. For now, add dummy read/write handlers to let
the FW disable the 2nd watchdog without error.
Reviewed-by: Peter Delevoryas <pdel@fb.com>
Reported-by: Peter Delevoryas <pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
hw/ssi/aspeed_smc.c | 19 ++++++++++++++++++-
1 file changed, 18 insertions(+), 1 deletion(-)
diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index 331a2c544635..715f85007d5e 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -124,6 +124,13 @@
/* SPI dummy cycle data */
#define R_DUMMY_DATA (0x54 / 4)
+/* FMC_WDT2 Control/Status Register for Alternate Boot (AST2600) */
+#define R_FMC_WDT2_CTRL (0x64 / 4)
+#define FMC_WDT2_CTRL_ALT_BOOT_MODE BIT(6) /* O: 2 chips 1: 1 chip */
+#define FMC_WDT2_CTRL_SINGLE_BOOT_MODE BIT(5)
+#define FMC_WDT2_CTRL_BOOT_SOURCE BIT(4) /* O: primary 1: alternate */
+#define FMC_WDT2_CTRL_EN BIT(0)
+
/* DMA Control/Status Register */
#define R_DMA_CTRL (0x80 / 4)
#define DMA_CTRL_REQUEST (1 << 31)
@@ -263,12 +270,18 @@ static void aspeed_2600_smc_dma_ctrl(AspeedSMCState *s, uint32_t value);
#define ASPEED_SMC_FEATURE_DMA 0x1
#define ASPEED_SMC_FEATURE_DMA_GRANT 0x2
+#define ASPEED_SMC_FEATURE_WDT_CONTROL 0x4
static inline bool aspeed_smc_has_dma(const AspeedSMCState *s)
{
return !!(s->ctrl->features & ASPEED_SMC_FEATURE_DMA);
}
+static inline bool aspeed_smc_has_wdt_control(const AspeedSMCState *s)
+{
+ return !!(s->ctrl->features & ASPEED_SMC_FEATURE_WDT_CONTROL);
+}
+
static const AspeedSMCController controllers[] = {
{
.name = "aspeed.smc-ast2400",
@@ -388,7 +401,8 @@ static const AspeedSMCController controllers[] = {
.segments = aspeed_segments_ast2600_fmc,
.flash_window_base = ASPEED26_SOC_FMC_FLASH_BASE,
.flash_window_size = 0x10000000,
- .features = ASPEED_SMC_FEATURE_DMA,
+ .features = ASPEED_SMC_FEATURE_DMA |
+ ASPEED_SMC_FEATURE_WDT_CONTROL,
.dma_flash_mask = 0x0FFFFFFC,
.dma_dram_mask = 0x3FFFFFFC,
.nregs = ASPEED_SMC_R_MAX,
@@ -1019,6 +1033,7 @@ static uint64_t aspeed_smc_read(void *opaque, hwaddr addr, unsigned int size)
addr == R_CE_CMD_CTRL ||
addr == R_INTR_CTRL ||
addr == R_DUMMY_DATA ||
+ (aspeed_smc_has_wdt_control(s) && addr == R_FMC_WDT2_CTRL) ||
(aspeed_smc_has_dma(s) && addr == R_DMA_CTRL) ||
(aspeed_smc_has_dma(s) && addr == R_DMA_FLASH_ADDR) ||
(aspeed_smc_has_dma(s) && addr == R_DMA_DRAM_ADDR) ||
@@ -1350,6 +1365,8 @@ static void aspeed_smc_write(void *opaque, hwaddr addr, uint64_t data,
s->regs[addr] = value & 0xff;
} else if (addr == R_DUMMY_DATA) {
s->regs[addr] = value & 0xff;
+ } else if (aspeed_smc_has_wdt_control(s) && addr == R_FMC_WDT2_CTRL) {
+ s->regs[addr] = value & FMC_WDT2_CTRL_EN;
} else if (addr == R_INTR_CTRL) {
s->regs[addr] = value;
} else if (aspeed_smc_has_dma(s) && addr == R_DMA_CTRL) {
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 02/18] aspeed/smc: Introduce aspeed_smc_error() helper
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
2021-10-12 7:37 ` [PULL 01/18] aspeed/smc: Add watchdog Control/Status Registers Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 03/18] aspeed/smc: Stop using the model name for the memory regions Cédric Le Goater
` (16 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Cédric Le Goater, qemu-arm, Joel Stanley,
qemu-devel
It unifies the errors reported by the Aspeed SMC model and also
removes some use of ctrl->name which will help us for the next
patches.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
hw/ssi/aspeed_smc.c | 97 +++++++++++++++++++++------------------------
1 file changed, 45 insertions(+), 52 deletions(-)
diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index 715f85007d5e..def1cb4c74c0 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -513,6 +513,9 @@ static void aspeed_2600_smc_reg_to_segment(const AspeedSMCState *s,
}
}
+#define aspeed_smc_error(fmt, ...) \
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: " fmt "\n", __func__, ## __VA_ARGS__)
+
static bool aspeed_smc_flash_overlap(const AspeedSMCState *s,
const AspeedSegments *new,
int cs)
@@ -529,11 +532,11 @@ static bool aspeed_smc_flash_overlap(const AspeedSMCState *s,
if (new->addr + new->size > seg.addr &&
new->addr < seg.addr + seg.size) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: new segment CS%d [ 0x%"
- HWADDR_PRIx" - 0x%"HWADDR_PRIx" ] overlaps with "
- "CS%d [ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]\n",
- s->ctrl->name, cs, new->addr, new->addr + new->size,
- i, seg.addr, seg.addr + seg.size);
+ aspeed_smc_error("new segment CS%d [ 0x%"
+ HWADDR_PRIx" - 0x%"HWADDR_PRIx" ] overlaps with "
+ "CS%d [ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]",
+ cs, new->addr, new->addr + new->size,
+ i, seg.addr, seg.addr + seg.size);
return true;
}
}
@@ -568,9 +571,8 @@ static void aspeed_smc_flash_set_segment(AspeedSMCState *s, int cs,
/* The start address of CS0 is read-only */
if (cs == 0 && seg.addr != s->ctrl->flash_window_base) {
- qemu_log_mask(LOG_GUEST_ERROR,
- "%s: Tried to change CS0 start address to 0x%"
- HWADDR_PRIx "\n", s->ctrl->name, seg.addr);
+ aspeed_smc_error("Tried to change CS0 start address to 0x%"
+ HWADDR_PRIx, seg.addr);
seg.addr = s->ctrl->flash_window_base;
new = s->ctrl->segment_to_reg(s, &seg);
}
@@ -584,9 +586,8 @@ static void aspeed_smc_flash_set_segment(AspeedSMCState *s, int cs,
cs == s->ctrl->max_peripherals &&
seg.addr + seg.size != s->ctrl->segments[cs].addr +
s->ctrl->segments[cs].size) {
- qemu_log_mask(LOG_GUEST_ERROR,
- "%s: Tried to change CS%d end address to 0x%"
- HWADDR_PRIx "\n", s->ctrl->name, cs, seg.addr + seg.size);
+ aspeed_smc_error("Tried to change CS%d end address to 0x%"
+ HWADDR_PRIx, cs, seg.addr + seg.size);
seg.size = s->ctrl->segments[cs].addr + s->ctrl->segments[cs].size -
seg.addr;
new = s->ctrl->segment_to_reg(s, &seg);
@@ -596,17 +597,17 @@ static void aspeed_smc_flash_set_segment(AspeedSMCState *s, int cs,
if (seg.size &&
(seg.addr + seg.size <= s->ctrl->flash_window_base ||
seg.addr > s->ctrl->flash_window_base + s->ctrl->flash_window_size)) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: new segment for CS%d is invalid : "
- "[ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]\n",
- s->ctrl->name, cs, seg.addr, seg.addr + seg.size);
+ aspeed_smc_error("new segment for CS%d is invalid : "
+ "[ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]",
+ cs, seg.addr, seg.addr + seg.size);
return;
}
/* Check start address vs. alignment */
if (seg.size && !QEMU_IS_ALIGNED(seg.addr, seg.size)) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: new segment for CS%d is not "
- "aligned : [ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]\n",
- s->ctrl->name, cs, seg.addr, seg.addr + seg.size);
+ aspeed_smc_error("new segment for CS%d is not "
+ "aligned : [ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]",
+ cs, seg.addr, seg.addr + seg.size);
}
/* And segments should not overlap (in the specs) */
@@ -619,16 +620,15 @@ static void aspeed_smc_flash_set_segment(AspeedSMCState *s, int cs,
static uint64_t aspeed_smc_flash_default_read(void *opaque, hwaddr addr,
unsigned size)
{
- qemu_log_mask(LOG_GUEST_ERROR, "%s: To 0x%" HWADDR_PRIx " of size %u"
- PRIx64 "\n", __func__, addr, size);
+ aspeed_smc_error("To 0x%" HWADDR_PRIx " of size %u" PRIx64, addr, size);
return 0;
}
static void aspeed_smc_flash_default_write(void *opaque, hwaddr addr,
uint64_t data, unsigned size)
{
- qemu_log_mask(LOG_GUEST_ERROR, "%s: To 0x%" HWADDR_PRIx " of size %u: 0x%"
- PRIx64 "\n", __func__, addr, size, data);
+ aspeed_smc_error("To 0x%" HWADDR_PRIx " of size %u: 0x%" PRIx64,
+ addr, size, data);
}
static const MemoryRegionOps aspeed_smc_flash_default_ops = {
@@ -671,8 +671,8 @@ static inline int aspeed_smc_flash_cmd(const AspeedSMCFlash *fl)
}
if (!cmd) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: no command defined for mode %d\n",
- __func__, aspeed_smc_flash_mode(fl));
+ aspeed_smc_error("no command defined for mode %d",
+ aspeed_smc_flash_mode(fl));
}
return cmd;
@@ -716,11 +716,9 @@ static uint32_t aspeed_smc_check_segment_addr(const AspeedSMCFlash *fl,
s->ctrl->reg_to_segment(s, s->regs[R_SEG_ADDR0 + fl->id], &seg);
if ((addr % seg.size) != addr) {
- qemu_log_mask(LOG_GUEST_ERROR,
- "%s: invalid address 0x%08x for CS%d segment : "
- "[ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]\n",
- s->ctrl->name, addr, fl->id, seg.addr,
- seg.addr + seg.size);
+ aspeed_smc_error("invalid address 0x%08x for CS%d segment : "
+ "[ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]",
+ addr, fl->id, seg.addr, seg.addr + seg.size);
addr %= seg.size;
}
@@ -796,8 +794,7 @@ static uint64_t aspeed_smc_flash_read(void *opaque, hwaddr addr, unsigned size)
aspeed_smc_flash_unselect(fl);
break;
default:
- qemu_log_mask(LOG_GUEST_ERROR, "%s: invalid flash mode %d\n",
- __func__, aspeed_smc_flash_mode(fl));
+ aspeed_smc_error("invalid flash mode %d", aspeed_smc_flash_mode(fl));
}
trace_aspeed_smc_flash_read(fl->id, addr, size, ret,
@@ -914,8 +911,7 @@ static void aspeed_smc_flash_write(void *opaque, hwaddr addr, uint64_t data,
aspeed_smc_flash_mode(fl));
if (!aspeed_smc_is_writable(fl)) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: flash is not writable at 0x%"
- HWADDR_PRIx "\n", __func__, addr);
+ aspeed_smc_error("flash is not writable at 0x%" HWADDR_PRIx, addr);
return;
}
@@ -940,8 +936,7 @@ static void aspeed_smc_flash_write(void *opaque, hwaddr addr, uint64_t data,
aspeed_smc_flash_unselect(fl);
break;
default:
- qemu_log_mask(LOG_GUEST_ERROR, "%s: invalid flash mode %d\n",
- __func__, aspeed_smc_flash_mode(fl));
+ aspeed_smc_error("invalid flash mode %d", aspeed_smc_flash_mode(fl));
}
}
@@ -1067,7 +1062,7 @@ static uint8_t aspeed_smc_hclk_divisor(uint8_t hclk_mask)
}
}
- qemu_log_mask(LOG_GUEST_ERROR, "invalid HCLK mask %x", hclk_mask);
+ aspeed_smc_error("invalid HCLK mask %x", hclk_mask);
return 0;
}
@@ -1147,8 +1142,7 @@ static void aspeed_smc_dma_checksum(AspeedSMCState *s)
uint32_t data;
if (s->regs[R_DMA_CTRL] & DMA_CTRL_WRITE) {
- qemu_log_mask(LOG_GUEST_ERROR,
- "%s: invalid direction for DMA checksum\n", __func__);
+ aspeed_smc_error("invalid direction for DMA checksum");
return;
}
@@ -1160,8 +1154,8 @@ static void aspeed_smc_dma_checksum(AspeedSMCState *s)
data = address_space_ldl_le(&s->flash_as, s->regs[R_DMA_FLASH_ADDR],
MEMTXATTRS_UNSPECIFIED, &result);
if (result != MEMTX_OK) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: Flash read failed @%08x\n",
- __func__, s->regs[R_DMA_FLASH_ADDR]);
+ aspeed_smc_error("Flash read failed @%08x",
+ s->regs[R_DMA_FLASH_ADDR]);
return;
}
trace_aspeed_smc_dma_checksum(s->regs[R_DMA_FLASH_ADDR], data);
@@ -1196,32 +1190,32 @@ static void aspeed_smc_dma_rw(AspeedSMCState *s)
data = address_space_ldl_le(&s->dram_as, s->regs[R_DMA_DRAM_ADDR],
MEMTXATTRS_UNSPECIFIED, &result);
if (result != MEMTX_OK) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: DRAM read failed @%08x\n",
- __func__, s->regs[R_DMA_DRAM_ADDR]);
+ aspeed_smc_error("DRAM read failed @%08x",
+ s->regs[R_DMA_DRAM_ADDR]);
return;
}
address_space_stl_le(&s->flash_as, s->regs[R_DMA_FLASH_ADDR],
data, MEMTXATTRS_UNSPECIFIED, &result);
if (result != MEMTX_OK) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: Flash write failed @%08x\n",
- __func__, s->regs[R_DMA_FLASH_ADDR]);
+ aspeed_smc_error("Flash write failed @%08x",
+ s->regs[R_DMA_FLASH_ADDR]);
return;
}
} else {
data = address_space_ldl_le(&s->flash_as, s->regs[R_DMA_FLASH_ADDR],
MEMTXATTRS_UNSPECIFIED, &result);
if (result != MEMTX_OK) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: Flash read failed @%08x\n",
- __func__, s->regs[R_DMA_FLASH_ADDR]);
+ aspeed_smc_error("Flash read failed @%08x",
+ s->regs[R_DMA_FLASH_ADDR]);
return;
}
address_space_stl_le(&s->dram_as, s->regs[R_DMA_DRAM_ADDR],
data, MEMTXATTRS_UNSPECIFIED, &result);
if (result != MEMTX_OK) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: DRAM write failed @%08x\n",
- __func__, s->regs[R_DMA_DRAM_ADDR]);
+ aspeed_smc_error("DRAM write failed @%08x",
+ s->regs[R_DMA_DRAM_ADDR]);
return;
}
}
@@ -1281,7 +1275,7 @@ static void aspeed_smc_dma_ctrl(AspeedSMCState *s, uint32_t dma_ctrl)
}
if (aspeed_smc_dma_in_progress(s)) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: DMA in progress\n", __func__);
+ aspeed_smc_error("DMA in progress !");
return;
}
@@ -1303,7 +1297,7 @@ static inline bool aspeed_smc_dma_granted(AspeedSMCState *s)
}
if (!(s->regs[R_DMA_CTRL] & DMA_CTRL_GRANT)) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: DMA not granted\n", __func__);
+ aspeed_smc_error("DMA not granted");
return false;
}
@@ -1328,7 +1322,7 @@ static void aspeed_2600_smc_dma_ctrl(AspeedSMCState *s, uint32_t dma_ctrl)
}
if (!aspeed_smc_dma_granted(s)) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: DMA not granted\n", __func__);
+ aspeed_smc_error("DMA not granted");
return;
}
@@ -1434,8 +1428,7 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
/* Enforce some real HW limits */
if (s->num_cs > s->ctrl->max_peripherals) {
- qemu_log_mask(LOG_GUEST_ERROR, "%s: num_cs cannot exceed: %d\n",
- __func__, s->ctrl->max_peripherals);
+ aspeed_smc_error("num_cs cannot exceed: %d", s->ctrl->max_peripherals);
s->num_cs = s->ctrl->max_peripherals;
}
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 03/18] aspeed/smc: Stop using the model name for the memory regions
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
2021-10-12 7:37 ` [PULL 01/18] aspeed/smc: Add watchdog Control/Status Registers Cédric Le Goater
2021-10-12 7:37 ` [PULL 02/18] aspeed/smc: Introduce aspeed_smc_error() helper Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 04/18] aspeed/smc: Drop AspeedSMCController structure Cédric Le Goater
` (15 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Cédric Le Goater, qemu-arm, Joel Stanley,
qemu-devel
There is no real reason to use this name. It's simply nice to have in
the monitor output but it's a burden for the following patch which
removes the AspeedSMCController structure describing the controller.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
hw/ssi/aspeed_smc.c | 25 ++++++++++---------------
1 file changed, 10 insertions(+), 15 deletions(-)
diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index def1cb4c74c0..612040493cf1 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -1392,20 +1392,15 @@ static const MemoryRegionOps aspeed_smc_ops = {
*/
static void aspeed_smc_dma_setup(AspeedSMCState *s, Error **errp)
{
- char *name;
-
if (!s->dram_mr) {
error_setg(errp, TYPE_ASPEED_SMC ": 'dram' link not set");
return;
}
- name = g_strdup_printf("%s-dma-flash", s->ctrl->name);
- address_space_init(&s->flash_as, &s->mmio_flash, name);
- g_free(name);
-
- name = g_strdup_printf("%s-dma-dram", s->ctrl->name);
- address_space_init(&s->dram_as, s->dram_mr, name);
- g_free(name);
+ address_space_init(&s->flash_as, &s->mmio_flash,
+ TYPE_ASPEED_SMC ".dma-flash");
+ address_space_init(&s->dram_as, s->dram_mr,
+ TYPE_ASPEED_SMC ".dma-dram");
}
static void aspeed_smc_realize(DeviceState *dev, Error **errp)
@@ -1446,7 +1441,7 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
/* The memory region for the controller registers */
memory_region_init_io(&s->mmio, OBJECT(s), &aspeed_smc_ops, s,
- s->ctrl->name, s->ctrl->nregs * 4);
+ TYPE_ASPEED_SMC, s->ctrl->nregs * 4);
sysbus_init_mmio(sbd, &s->mmio);
/*
@@ -1454,12 +1449,12 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
* window in which the flash modules are mapped. The size and
* address depends on the SoC model and controller type.
*/
- snprintf(name, sizeof(name), "%s.flash", s->ctrl->name);
-
memory_region_init_io(&s->mmio_flash, OBJECT(s),
- &aspeed_smc_flash_default_ops, s, name,
+ &aspeed_smc_flash_default_ops, s,
+ TYPE_ASPEED_SMC ".flash",
s->ctrl->flash_window_size);
- memory_region_init_alias(&s->mmio_flash_alias, OBJECT(s), name,
+ memory_region_init_alias(&s->mmio_flash_alias, OBJECT(s),
+ TYPE_ASPEED_SMC ".flash",
&s->mmio_flash, 0, s->ctrl->flash_window_size);
sysbus_init_mmio(sbd, &s->mmio_flash_alias);
@@ -1475,7 +1470,7 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
for (i = 0; i < s->ctrl->max_peripherals; ++i) {
AspeedSMCFlash *fl = &s->flashes[i];
- snprintf(name, sizeof(name), "%s.%d", s->ctrl->name, i);
+ snprintf(name, sizeof(name), TYPE_ASPEED_SMC ".flash.%d", i);
fl->id = i;
fl->controller = s;
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 04/18] aspeed/smc: Drop AspeedSMCController structure
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (2 preceding siblings ...)
2021-10-12 7:37 ` [PULL 03/18] aspeed/smc: Stop using the model name for the memory regions Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 05/18] aspeed/smc: Remove the 'flash' attribute from AspeedSMCFlash Cédric Le Goater
` (14 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Cédric Le Goater, qemu-arm, Joel Stanley,
qemu-devel
The characteristics of the Aspeed controllers are described in a
AspeedSMCController structure which is redundant with the
AspeedSMCClass. Move all attributes under the class and adapt the code
to use class attributes instead.
This is a large change but it is functionally equivalent.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/ssi/aspeed_smc.h | 64 ++-
hw/arm/aspeed_ast2600.c | 4 +-
hw/arm/aspeed_soc.c | 4 +-
hw/ssi/aspeed_smc.c | 861 ++++++++++++++++++++----------------
4 files changed, 511 insertions(+), 422 deletions(-)
diff --git a/include/hw/ssi/aspeed_smc.h b/include/hw/ssi/aspeed_smc.h
index cdaf165300b6..0ea536a44c3a 100644
--- a/include/hw/ssi/aspeed_smc.h
+++ b/include/hw/ssi/aspeed_smc.h
@@ -29,35 +29,7 @@
#include "hw/sysbus.h"
#include "qom/object.h"
-typedef struct AspeedSegments {
- hwaddr addr;
- uint32_t size;
-} AspeedSegments;
-
struct AspeedSMCState;
-typedef struct AspeedSMCController {
- const char *name;
- uint8_t r_conf;
- uint8_t r_ce_ctrl;
- uint8_t r_ctrl0;
- uint8_t r_timings;
- uint8_t nregs_timings;
- uint8_t conf_enable_w0;
- uint8_t max_peripherals;
- const AspeedSegments *segments;
- hwaddr flash_window_base;
- uint32_t flash_window_size;
- uint32_t features;
- hwaddr dma_flash_mask;
- hwaddr dma_dram_mask;
- uint32_t nregs;
- uint32_t (*segment_to_reg)(const struct AspeedSMCState *s,
- const AspeedSegments *seg);
- void (*reg_to_segment)(const struct AspeedSMCState *s, uint32_t reg,
- AspeedSegments *seg);
- void (*dma_ctrl)(struct AspeedSMCState *s, uint32_t value);
-} AspeedSMCController;
-
typedef struct AspeedSMCFlash {
struct AspeedSMCState *controller;
@@ -71,18 +43,11 @@ typedef struct AspeedSMCFlash {
#define TYPE_ASPEED_SMC "aspeed.smc"
OBJECT_DECLARE_TYPE(AspeedSMCState, AspeedSMCClass, ASPEED_SMC)
-struct AspeedSMCClass {
- SysBusDevice parent_obj;
- const AspeedSMCController *ctrl;
-};
-
#define ASPEED_SMC_R_MAX (0x100 / 4)
struct AspeedSMCState {
SysBusDevice parent_obj;
- const AspeedSMCController *ctrl;
-
MemoryRegion mmio;
MemoryRegion mmio_flash;
MemoryRegion mmio_flash_alias;
@@ -115,4 +80,33 @@ struct AspeedSMCState {
uint8_t snoop_dummies;
};
+typedef struct AspeedSegments {
+ hwaddr addr;
+ uint32_t size;
+} AspeedSegments;
+
+struct AspeedSMCClass {
+ SysBusDeviceClass parent_obj;
+
+ uint8_t r_conf;
+ uint8_t r_ce_ctrl;
+ uint8_t r_ctrl0;
+ uint8_t r_timings;
+ uint8_t nregs_timings;
+ uint8_t conf_enable_w0;
+ uint8_t max_peripherals;
+ const AspeedSegments *segments;
+ hwaddr flash_window_base;
+ uint32_t flash_window_size;
+ uint32_t features;
+ hwaddr dma_flash_mask;
+ hwaddr dma_dram_mask;
+ uint32_t nregs;
+ uint32_t (*segment_to_reg)(const AspeedSMCState *s,
+ const AspeedSegments *seg);
+ void (*reg_to_segment)(const AspeedSMCState *s, uint32_t reg,
+ AspeedSegments *seg);
+ void (*dma_ctrl)(AspeedSMCState *s, uint32_t value);
+};
+
#endif /* ASPEED_SMC_H */
diff --git a/hw/arm/aspeed_ast2600.c b/hw/arm/aspeed_ast2600.c
index 9d70e8e060c6..c69f27dff62a 100644
--- a/hw/arm/aspeed_ast2600.c
+++ b/hw/arm/aspeed_ast2600.c
@@ -352,7 +352,7 @@ static void aspeed_soc_ast2600_realize(DeviceState *dev, Error **errp)
}
sysbus_mmio_map(SYS_BUS_DEVICE(&s->fmc), 0, sc->memmap[ASPEED_DEV_FMC]);
sysbus_mmio_map(SYS_BUS_DEVICE(&s->fmc), 1,
- s->fmc.ctrl->flash_window_base);
+ ASPEED_SMC_GET_CLASS(&s->fmc)->flash_window_base);
sysbus_connect_irq(SYS_BUS_DEVICE(&s->fmc), 0,
aspeed_soc_get_irq(s, ASPEED_DEV_FMC));
@@ -367,7 +367,7 @@ static void aspeed_soc_ast2600_realize(DeviceState *dev, Error **errp)
sysbus_mmio_map(SYS_BUS_DEVICE(&s->spi[i]), 0,
sc->memmap[ASPEED_DEV_SPI1 + i]);
sysbus_mmio_map(SYS_BUS_DEVICE(&s->spi[i]), 1,
- s->spi[i].ctrl->flash_window_base);
+ ASPEED_SMC_GET_CLASS(&s->spi[i])->flash_window_base);
}
/* EHCI */
diff --git a/hw/arm/aspeed_soc.c b/hw/arm/aspeed_soc.c
index ed84502e238a..4f013dd5cd9c 100644
--- a/hw/arm/aspeed_soc.c
+++ b/hw/arm/aspeed_soc.c
@@ -310,7 +310,7 @@ static void aspeed_soc_realize(DeviceState *dev, Error **errp)
}
sysbus_mmio_map(SYS_BUS_DEVICE(&s->fmc), 0, sc->memmap[ASPEED_DEV_FMC]);
sysbus_mmio_map(SYS_BUS_DEVICE(&s->fmc), 1,
- s->fmc.ctrl->flash_window_base);
+ ASPEED_SMC_GET_CLASS(&s->fmc)->flash_window_base);
sysbus_connect_irq(SYS_BUS_DEVICE(&s->fmc), 0,
aspeed_soc_get_irq(s, ASPEED_DEV_FMC));
@@ -323,7 +323,7 @@ static void aspeed_soc_realize(DeviceState *dev, Error **errp)
sysbus_mmio_map(SYS_BUS_DEVICE(&s->spi[i]), 0,
sc->memmap[ASPEED_DEV_SPI1 + i]);
sysbus_mmio_map(SYS_BUS_DEVICE(&s->spi[i]), 1,
- s->spi[i].ctrl->flash_window_base);
+ ASPEED_SMC_GET_CLASS(&s->spi[i])->flash_window_base);
}
/* EHCI */
diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index 612040493cf1..5466be631719 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -169,11 +169,6 @@
#define ASPEED_SMC_R_SPI_MAX (0x20 / 4)
#define ASPEED_SMC_R_SMC_MAX (0x20 / 4)
-#define ASPEED_SOC_SMC_FLASH_BASE 0x10000000
-#define ASPEED_SOC_FMC_FLASH_BASE 0x20000000
-#define ASPEED_SOC_SPI_FLASH_BASE 0x30000000
-#define ASPEED_SOC_SPI2_FLASH_BASE 0x38000000
-
/*
* DMA DRAM addresses should be 4 bytes aligned and the valid address
* range is 0x40000000 - 0x5FFFFFFF (AST2400)
@@ -186,8 +181,8 @@
* 0: 4 bytes
* 0x7FFFFF: 32M bytes
*/
-#define DMA_DRAM_ADDR(s, val) ((val) & (s)->ctrl->dma_dram_mask)
-#define DMA_FLASH_ADDR(s, val) ((val) & (s)->ctrl->dma_flash_mask)
+#define DMA_DRAM_ADDR(asc, val) ((val) & (asc)->dma_dram_mask)
+#define DMA_FLASH_ADDR(asc, val) ((val) & (asc)->dma_flash_mask)
#define DMA_LENGTH(val) ((val) & 0x01FFFFFC)
/* Flash opcodes. */
@@ -201,316 +196,25 @@
* controller. These can be changed when board is initialized with the
* Segment Address Registers.
*/
-static const AspeedSegments aspeed_segments_legacy[] = {
- { 0x10000000, 32 * 1024 * 1024 },
-};
-
-static const AspeedSegments aspeed_segments_fmc[] = {
- { 0x20000000, 64 * 1024 * 1024 }, /* start address is readonly */
- { 0x24000000, 32 * 1024 * 1024 },
- { 0x26000000, 32 * 1024 * 1024 },
- { 0x28000000, 32 * 1024 * 1024 },
- { 0x2A000000, 32 * 1024 * 1024 }
-};
-
-static const AspeedSegments aspeed_segments_spi[] = {
- { 0x30000000, 64 * 1024 * 1024 },
-};
-
-static const AspeedSegments aspeed_segments_ast2500_fmc[] = {
- { 0x20000000, 128 * 1024 * 1024 }, /* start address is readonly */
- { 0x28000000, 32 * 1024 * 1024 },
- { 0x2A000000, 32 * 1024 * 1024 },
-};
-
-static const AspeedSegments aspeed_segments_ast2500_spi1[] = {
- { 0x30000000, 32 * 1024 * 1024 }, /* start address is readonly */
- { 0x32000000, 96 * 1024 * 1024 }, /* end address is readonly */
-};
-
-static const AspeedSegments aspeed_segments_ast2500_spi2[] = {
- { 0x38000000, 32 * 1024 * 1024 }, /* start address is readonly */
- { 0x3A000000, 96 * 1024 * 1024 }, /* end address is readonly */
-};
-static uint32_t aspeed_smc_segment_to_reg(const AspeedSMCState *s,
- const AspeedSegments *seg);
-static void aspeed_smc_reg_to_segment(const AspeedSMCState *s, uint32_t reg,
- AspeedSegments *seg);
-static void aspeed_smc_dma_ctrl(AspeedSMCState *s, uint32_t value);
-
-/*
- * AST2600 definitions
- */
-#define ASPEED26_SOC_FMC_FLASH_BASE 0x20000000
-#define ASPEED26_SOC_SPI_FLASH_BASE 0x30000000
-#define ASPEED26_SOC_SPI2_FLASH_BASE 0x50000000
-
-static const AspeedSegments aspeed_segments_ast2600_fmc[] = {
- { 0x0, 128 * MiB }, /* start address is readonly */
- { 128 * MiB, 128 * MiB }, /* default is disabled but needed for -kernel */
- { 0x0, 0 }, /* disabled */
-};
-
-static const AspeedSegments aspeed_segments_ast2600_spi1[] = {
- { 0x0, 128 * MiB }, /* start address is readonly */
- { 0x0, 0 }, /* disabled */
-};
-
-static const AspeedSegments aspeed_segments_ast2600_spi2[] = {
- { 0x0, 128 * MiB }, /* start address is readonly */
- { 0x0, 0 }, /* disabled */
- { 0x0, 0 }, /* disabled */
-};
-
-static uint32_t aspeed_2600_smc_segment_to_reg(const AspeedSMCState *s,
- const AspeedSegments *seg);
-static void aspeed_2600_smc_reg_to_segment(const AspeedSMCState *s,
- uint32_t reg, AspeedSegments *seg);
-static void aspeed_2600_smc_dma_ctrl(AspeedSMCState *s, uint32_t value);
+static const AspeedSegments aspeed_2400_fmc_segments[];
+static const AspeedSegments aspeed_2400_spi1_segments[];
+static const AspeedSegments aspeed_2500_fmc_segments[];
+static const AspeedSegments aspeed_2500_spi1_segments[];
+static const AspeedSegments aspeed_2500_spi2_segments[];
+static const AspeedSegments aspeed_2600_fmc_segments[];
#define ASPEED_SMC_FEATURE_DMA 0x1
#define ASPEED_SMC_FEATURE_DMA_GRANT 0x2
#define ASPEED_SMC_FEATURE_WDT_CONTROL 0x4
-static inline bool aspeed_smc_has_dma(const AspeedSMCState *s)
-{
- return !!(s->ctrl->features & ASPEED_SMC_FEATURE_DMA);
-}
-
-static inline bool aspeed_smc_has_wdt_control(const AspeedSMCState *s)
-{
- return !!(s->ctrl->features & ASPEED_SMC_FEATURE_WDT_CONTROL);
-}
-
-static const AspeedSMCController controllers[] = {
- {
- .name = "aspeed.smc-ast2400",
- .r_conf = R_CONF,
- .r_ce_ctrl = R_CE_CTRL,
- .r_ctrl0 = R_CTRL0,
- .r_timings = R_TIMINGS,
- .nregs_timings = 1,
- .conf_enable_w0 = CONF_ENABLE_W0,
- .max_peripherals = 1,
- .segments = aspeed_segments_legacy,
- .flash_window_base = ASPEED_SOC_SMC_FLASH_BASE,
- .flash_window_size = 0x6000000,
- .features = 0x0,
- .nregs = ASPEED_SMC_R_SMC_MAX,
- .segment_to_reg = aspeed_smc_segment_to_reg,
- .reg_to_segment = aspeed_smc_reg_to_segment,
- .dma_ctrl = aspeed_smc_dma_ctrl,
- }, {
- .name = "aspeed.fmc-ast2400",
- .r_conf = R_CONF,
- .r_ce_ctrl = R_CE_CTRL,
- .r_ctrl0 = R_CTRL0,
- .r_timings = R_TIMINGS,
- .nregs_timings = 1,
- .conf_enable_w0 = CONF_ENABLE_W0,
- .max_peripherals = 5,
- .segments = aspeed_segments_fmc,
- .flash_window_base = ASPEED_SOC_FMC_FLASH_BASE,
- .flash_window_size = 0x10000000,
- .features = ASPEED_SMC_FEATURE_DMA,
- .dma_flash_mask = 0x0FFFFFFC,
- .dma_dram_mask = 0x1FFFFFFC,
- .nregs = ASPEED_SMC_R_MAX,
- .segment_to_reg = aspeed_smc_segment_to_reg,
- .reg_to_segment = aspeed_smc_reg_to_segment,
- .dma_ctrl = aspeed_smc_dma_ctrl,
- }, {
- .name = "aspeed.spi1-ast2400",
- .r_conf = R_SPI_CONF,
- .r_ce_ctrl = 0xff,
- .r_ctrl0 = R_SPI_CTRL0,
- .r_timings = R_SPI_TIMINGS,
- .nregs_timings = 1,
- .conf_enable_w0 = SPI_CONF_ENABLE_W0,
- .max_peripherals = 1,
- .segments = aspeed_segments_spi,
- .flash_window_base = ASPEED_SOC_SPI_FLASH_BASE,
- .flash_window_size = 0x10000000,
- .features = 0x0,
- .nregs = ASPEED_SMC_R_SPI_MAX,
- .segment_to_reg = aspeed_smc_segment_to_reg,
- .reg_to_segment = aspeed_smc_reg_to_segment,
- .dma_ctrl = aspeed_smc_dma_ctrl,
- }, {
- .name = "aspeed.fmc-ast2500",
- .r_conf = R_CONF,
- .r_ce_ctrl = R_CE_CTRL,
- .r_ctrl0 = R_CTRL0,
- .r_timings = R_TIMINGS,
- .nregs_timings = 1,
- .conf_enable_w0 = CONF_ENABLE_W0,
- .max_peripherals = 3,
- .segments = aspeed_segments_ast2500_fmc,
- .flash_window_base = ASPEED_SOC_FMC_FLASH_BASE,
- .flash_window_size = 0x10000000,
- .features = ASPEED_SMC_FEATURE_DMA,
- .dma_flash_mask = 0x0FFFFFFC,
- .dma_dram_mask = 0x3FFFFFFC,
- .nregs = ASPEED_SMC_R_MAX,
- .segment_to_reg = aspeed_smc_segment_to_reg,
- .reg_to_segment = aspeed_smc_reg_to_segment,
- .dma_ctrl = aspeed_smc_dma_ctrl,
- }, {
- .name = "aspeed.spi1-ast2500",
- .r_conf = R_CONF,
- .r_ce_ctrl = R_CE_CTRL,
- .r_ctrl0 = R_CTRL0,
- .r_timings = R_TIMINGS,
- .nregs_timings = 1,
- .conf_enable_w0 = CONF_ENABLE_W0,
- .max_peripherals = 2,
- .segments = aspeed_segments_ast2500_spi1,
- .flash_window_base = ASPEED_SOC_SPI_FLASH_BASE,
- .flash_window_size = 0x8000000,
- .features = 0x0,
- .nregs = ASPEED_SMC_R_MAX,
- .segment_to_reg = aspeed_smc_segment_to_reg,
- .reg_to_segment = aspeed_smc_reg_to_segment,
- .dma_ctrl = aspeed_smc_dma_ctrl,
- }, {
- .name = "aspeed.spi2-ast2500",
- .r_conf = R_CONF,
- .r_ce_ctrl = R_CE_CTRL,
- .r_ctrl0 = R_CTRL0,
- .r_timings = R_TIMINGS,
- .nregs_timings = 1,
- .conf_enable_w0 = CONF_ENABLE_W0,
- .max_peripherals = 2,
- .segments = aspeed_segments_ast2500_spi2,
- .flash_window_base = ASPEED_SOC_SPI2_FLASH_BASE,
- .flash_window_size = 0x8000000,
- .features = 0x0,
- .nregs = ASPEED_SMC_R_MAX,
- .segment_to_reg = aspeed_smc_segment_to_reg,
- .reg_to_segment = aspeed_smc_reg_to_segment,
- .dma_ctrl = aspeed_smc_dma_ctrl,
- }, {
- .name = "aspeed.fmc-ast2600",
- .r_conf = R_CONF,
- .r_ce_ctrl = R_CE_CTRL,
- .r_ctrl0 = R_CTRL0,
- .r_timings = R_TIMINGS,
- .nregs_timings = 1,
- .conf_enable_w0 = CONF_ENABLE_W0,
- .max_peripherals = 3,
- .segments = aspeed_segments_ast2600_fmc,
- .flash_window_base = ASPEED26_SOC_FMC_FLASH_BASE,
- .flash_window_size = 0x10000000,
- .features = ASPEED_SMC_FEATURE_DMA |
- ASPEED_SMC_FEATURE_WDT_CONTROL,
- .dma_flash_mask = 0x0FFFFFFC,
- .dma_dram_mask = 0x3FFFFFFC,
- .nregs = ASPEED_SMC_R_MAX,
- .segment_to_reg = aspeed_2600_smc_segment_to_reg,
- .reg_to_segment = aspeed_2600_smc_reg_to_segment,
- .dma_ctrl = aspeed_2600_smc_dma_ctrl,
- }, {
- .name = "aspeed.spi1-ast2600",
- .r_conf = R_CONF,
- .r_ce_ctrl = R_CE_CTRL,
- .r_ctrl0 = R_CTRL0,
- .r_timings = R_TIMINGS,
- .nregs_timings = 2,
- .conf_enable_w0 = CONF_ENABLE_W0,
- .max_peripherals = 2,
- .segments = aspeed_segments_ast2600_spi1,
- .flash_window_base = ASPEED26_SOC_SPI_FLASH_BASE,
- .flash_window_size = 0x10000000,
- .features = ASPEED_SMC_FEATURE_DMA |
- ASPEED_SMC_FEATURE_DMA_GRANT,
- .dma_flash_mask = 0x0FFFFFFC,
- .dma_dram_mask = 0x3FFFFFFC,
- .nregs = ASPEED_SMC_R_MAX,
- .segment_to_reg = aspeed_2600_smc_segment_to_reg,
- .reg_to_segment = aspeed_2600_smc_reg_to_segment,
- .dma_ctrl = aspeed_2600_smc_dma_ctrl,
- }, {
- .name = "aspeed.spi2-ast2600",
- .r_conf = R_CONF,
- .r_ce_ctrl = R_CE_CTRL,
- .r_ctrl0 = R_CTRL0,
- .r_timings = R_TIMINGS,
- .nregs_timings = 3,
- .conf_enable_w0 = CONF_ENABLE_W0,
- .max_peripherals = 3,
- .segments = aspeed_segments_ast2600_spi2,
- .flash_window_base = ASPEED26_SOC_SPI2_FLASH_BASE,
- .flash_window_size = 0x10000000,
- .features = ASPEED_SMC_FEATURE_DMA |
- ASPEED_SMC_FEATURE_DMA_GRANT,
- .dma_flash_mask = 0x0FFFFFFC,
- .dma_dram_mask = 0x3FFFFFFC,
- .nregs = ASPEED_SMC_R_MAX,
- .segment_to_reg = aspeed_2600_smc_segment_to_reg,
- .reg_to_segment = aspeed_2600_smc_reg_to_segment,
- .dma_ctrl = aspeed_2600_smc_dma_ctrl,
- },
-};
-
-/*
- * The Segment Registers of the AST2400 and AST2500 have a 8MB
- * unit. The address range of a flash SPI peripheral is encoded with
- * absolute addresses which should be part of the overall controller
- * window.
- */
-static uint32_t aspeed_smc_segment_to_reg(const AspeedSMCState *s,
- const AspeedSegments *seg)
-{
- uint32_t reg = 0;
- reg |= ((seg->addr >> 23) & SEG_START_MASK) << SEG_START_SHIFT;
- reg |= (((seg->addr + seg->size) >> 23) & SEG_END_MASK) << SEG_END_SHIFT;
- return reg;
-}
-
-static void aspeed_smc_reg_to_segment(const AspeedSMCState *s,
- uint32_t reg, AspeedSegments *seg)
-{
- seg->addr = ((reg >> SEG_START_SHIFT) & SEG_START_MASK) << 23;
- seg->size = (((reg >> SEG_END_SHIFT) & SEG_END_MASK) << 23) - seg->addr;
-}
-
-/*
- * The Segment Registers of the AST2600 have a 1MB unit. The address
- * range of a flash SPI peripheral is encoded with offsets in the overall
- * controller window. The previous SoC AST2400 and AST2500 used
- * absolute addresses. Only bits [27:20] are relevant and the end
- * address is an upper bound limit.
- */
-#define AST2600_SEG_ADDR_MASK 0x0ff00000
-
-static uint32_t aspeed_2600_smc_segment_to_reg(const AspeedSMCState *s,
- const AspeedSegments *seg)
+static inline bool aspeed_smc_has_dma(const AspeedSMCClass *asc)
{
- uint32_t reg = 0;
-
- /* Disabled segments have a nil register */
- if (!seg->size) {
- return 0;
- }
-
- reg |= (seg->addr & AST2600_SEG_ADDR_MASK) >> 16; /* start offset */
- reg |= (seg->addr + seg->size - 1) & AST2600_SEG_ADDR_MASK; /* end offset */
- return reg;
+ return !!(asc->features & ASPEED_SMC_FEATURE_DMA);
}
-static void aspeed_2600_smc_reg_to_segment(const AspeedSMCState *s,
- uint32_t reg, AspeedSegments *seg)
+static inline bool aspeed_smc_has_wdt_control(const AspeedSMCClass *asc)
{
- uint32_t start_offset = (reg << 16) & AST2600_SEG_ADDR_MASK;
- uint32_t end_offset = reg & AST2600_SEG_ADDR_MASK;
-
- if (reg) {
- seg->addr = s->ctrl->flash_window_base + start_offset;
- seg->size = end_offset + MiB - start_offset;
- } else {
- seg->addr = s->ctrl->flash_window_base;
- seg->size = 0;
- }
+ return !!(asc->features & ASPEED_SMC_FEATURE_WDT_CONTROL);
}
#define aspeed_smc_error(fmt, ...) \
@@ -520,15 +224,16 @@ static bool aspeed_smc_flash_overlap(const AspeedSMCState *s,
const AspeedSegments *new,
int cs)
{
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
AspeedSegments seg;
int i;
- for (i = 0; i < s->ctrl->max_peripherals; i++) {
+ for (i = 0; i < asc->max_peripherals; i++) {
if (i == cs) {
continue;
}
- s->ctrl->reg_to_segment(s, s->regs[R_SEG_ADDR0 + i], &seg);
+ asc->reg_to_segment(s, s->regs[R_SEG_ADDR0 + i], &seg);
if (new->addr + new->size > seg.addr &&
new->addr < seg.addr + seg.size) {
@@ -546,14 +251,15 @@ static bool aspeed_smc_flash_overlap(const AspeedSMCState *s,
static void aspeed_smc_flash_set_segment_region(AspeedSMCState *s, int cs,
uint64_t regval)
{
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
AspeedSMCFlash *fl = &s->flashes[cs];
AspeedSegments seg;
- s->ctrl->reg_to_segment(s, regval, &seg);
+ asc->reg_to_segment(s, regval, &seg);
memory_region_transaction_begin();
memory_region_set_size(&fl->mmio, seg.size);
- memory_region_set_address(&fl->mmio, seg.addr - s->ctrl->flash_window_base);
+ memory_region_set_address(&fl->mmio, seg.addr - asc->flash_window_base);
memory_region_set_enabled(&fl->mmio, !!seg.size);
memory_region_transaction_commit();
@@ -563,40 +269,41 @@ static void aspeed_smc_flash_set_segment_region(AspeedSMCState *s, int cs,
static void aspeed_smc_flash_set_segment(AspeedSMCState *s, int cs,
uint64_t new)
{
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
AspeedSegments seg;
- s->ctrl->reg_to_segment(s, new, &seg);
+ asc->reg_to_segment(s, new, &seg);
trace_aspeed_smc_flash_set_segment(cs, new, seg.addr, seg.addr + seg.size);
/* The start address of CS0 is read-only */
- if (cs == 0 && seg.addr != s->ctrl->flash_window_base) {
+ if (cs == 0 && seg.addr != asc->flash_window_base) {
aspeed_smc_error("Tried to change CS0 start address to 0x%"
HWADDR_PRIx, seg.addr);
- seg.addr = s->ctrl->flash_window_base;
- new = s->ctrl->segment_to_reg(s, &seg);
+ seg.addr = asc->flash_window_base;
+ new = asc->segment_to_reg(s, &seg);
}
/*
* The end address of the AST2500 spi controllers is also
* read-only.
*/
- if ((s->ctrl->segments == aspeed_segments_ast2500_spi1 ||
- s->ctrl->segments == aspeed_segments_ast2500_spi2) &&
- cs == s->ctrl->max_peripherals &&
- seg.addr + seg.size != s->ctrl->segments[cs].addr +
- s->ctrl->segments[cs].size) {
+ if ((asc->segments == aspeed_2500_spi1_segments ||
+ asc->segments == aspeed_2500_spi2_segments) &&
+ cs == asc->max_peripherals &&
+ seg.addr + seg.size != asc->segments[cs].addr +
+ asc->segments[cs].size) {
aspeed_smc_error("Tried to change CS%d end address to 0x%"
HWADDR_PRIx, cs, seg.addr + seg.size);
- seg.size = s->ctrl->segments[cs].addr + s->ctrl->segments[cs].size -
+ seg.size = asc->segments[cs].addr + asc->segments[cs].size -
seg.addr;
- new = s->ctrl->segment_to_reg(s, &seg);
+ new = asc->segment_to_reg(s, &seg);
}
/* Keep the segment in the overall flash window */
if (seg.size &&
- (seg.addr + seg.size <= s->ctrl->flash_window_base ||
- seg.addr > s->ctrl->flash_window_base + s->ctrl->flash_window_size)) {
+ (seg.addr + seg.size <= asc->flash_window_base ||
+ seg.addr > asc->flash_window_base + asc->flash_window_size)) {
aspeed_smc_error("new segment for CS%d is invalid : "
"[ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]",
cs, seg.addr, seg.addr + seg.size);
@@ -681,8 +388,9 @@ static inline int aspeed_smc_flash_cmd(const AspeedSMCFlash *fl)
static inline int aspeed_smc_flash_is_4byte(const AspeedSMCFlash *fl)
{
const AspeedSMCState *s = fl->controller;
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
- if (s->ctrl->segments == aspeed_segments_spi) {
+ if (asc->segments == aspeed_2400_spi1_segments) {
return s->regs[s->r_ctrl0] & CTRL_AST2400_SPI_4BYTE;
} else {
return s->regs[s->r_ce_ctrl] & (1 << (CTRL_EXTENDED0 + fl->id));
@@ -712,9 +420,10 @@ static uint32_t aspeed_smc_check_segment_addr(const AspeedSMCFlash *fl,
uint32_t addr)
{
const AspeedSMCState *s = fl->controller;
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
AspeedSegments seg;
- s->ctrl->reg_to_segment(s, s->regs[R_SEG_ADDR0 + fl->id], &seg);
+ asc->reg_to_segment(s, s->regs[R_SEG_ADDR0 + fl->id], &seg);
if ((addr % seg.size) != addr) {
aspeed_smc_error("invalid address 0x%08x for CS%d segment : "
"[ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]",
@@ -974,6 +683,7 @@ static void aspeed_smc_flash_update_ctrl(AspeedSMCFlash *fl, uint32_t value)
static void aspeed_smc_reset(DeviceState *d)
{
AspeedSMCState *s = ASPEED_SMC(d);
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
int i;
memset(s->regs, 0, sizeof s->regs);
@@ -985,13 +695,13 @@ static void aspeed_smc_reset(DeviceState *d)
}
/* setup the default segment register values and regions for all */
- for (i = 0; i < s->ctrl->max_peripherals; ++i) {
+ for (i = 0; i < asc->max_peripherals; ++i) {
aspeed_smc_flash_set_segment_region(s, i,
- s->ctrl->segment_to_reg(s, &s->ctrl->segments[i]));
+ asc->segment_to_reg(s, &asc->segments[i]));
}
/* HW strapping flash type for the AST2600 controllers */
- if (s->ctrl->segments == aspeed_segments_ast2600_fmc) {
+ if (asc->segments == aspeed_2600_fmc_segments) {
/* flash type is fixed to SPI for all */
s->regs[s->r_conf] |= (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0);
s->regs[s->r_conf] |= (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE1);
@@ -999,7 +709,7 @@ static void aspeed_smc_reset(DeviceState *d)
}
/* HW strapping flash type for FMC controllers */
- if (s->ctrl->segments == aspeed_segments_ast2500_fmc) {
+ if (asc->segments == aspeed_2500_fmc_segments) {
/* flash type is fixed to SPI for CE0 and CE1 */
s->regs[s->r_conf] |= (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0);
s->regs[s->r_conf] |= (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE1);
@@ -1007,7 +717,7 @@ static void aspeed_smc_reset(DeviceState *d)
/* HW strapping for AST2400 FMC controllers (SCU70). Let's use the
* configuration of the palmetto-bmc machine */
- if (s->ctrl->segments == aspeed_segments_fmc) {
+ if (asc->segments == aspeed_2400_fmc_segments) {
s->regs[s->r_conf] |= (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0);
}
@@ -1018,25 +728,26 @@ static void aspeed_smc_reset(DeviceState *d)
static uint64_t aspeed_smc_read(void *opaque, hwaddr addr, unsigned int size)
{
AspeedSMCState *s = ASPEED_SMC(opaque);
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(opaque);
addr >>= 2;
if (addr == s->r_conf ||
(addr >= s->r_timings &&
- addr < s->r_timings + s->ctrl->nregs_timings) ||
+ addr < s->r_timings + asc->nregs_timings) ||
addr == s->r_ce_ctrl ||
addr == R_CE_CMD_CTRL ||
addr == R_INTR_CTRL ||
addr == R_DUMMY_DATA ||
- (aspeed_smc_has_wdt_control(s) && addr == R_FMC_WDT2_CTRL) ||
- (aspeed_smc_has_dma(s) && addr == R_DMA_CTRL) ||
- (aspeed_smc_has_dma(s) && addr == R_DMA_FLASH_ADDR) ||
- (aspeed_smc_has_dma(s) && addr == R_DMA_DRAM_ADDR) ||
- (aspeed_smc_has_dma(s) && addr == R_DMA_LEN) ||
- (aspeed_smc_has_dma(s) && addr == R_DMA_CHECKSUM) ||
+ (aspeed_smc_has_wdt_control(asc) && addr == R_FMC_WDT2_CTRL) ||
+ (aspeed_smc_has_dma(asc) && addr == R_DMA_CTRL) ||
+ (aspeed_smc_has_dma(asc) && addr == R_DMA_FLASH_ADDR) ||
+ (aspeed_smc_has_dma(asc) && addr == R_DMA_DRAM_ADDR) ||
+ (aspeed_smc_has_dma(asc) && addr == R_DMA_LEN) ||
+ (aspeed_smc_has_dma(asc) && addr == R_DMA_CHECKSUM) ||
(addr >= R_SEG_ADDR0 &&
- addr < R_SEG_ADDR0 + s->ctrl->max_peripherals) ||
- (addr >= s->r_ctrl0 && addr < s->r_ctrl0 + s->ctrl->max_peripherals)) {
+ addr < R_SEG_ADDR0 + asc->max_peripherals) ||
+ (addr >= s->r_ctrl0 && addr < s->r_ctrl0 + asc->max_peripherals)) {
trace_aspeed_smc_read(addr, size, s->regs[addr]);
@@ -1292,7 +1003,9 @@ static void aspeed_smc_dma_ctrl(AspeedSMCState *s, uint32_t dma_ctrl)
static inline bool aspeed_smc_dma_granted(AspeedSMCState *s)
{
- if (!(s->ctrl->features & ASPEED_SMC_FEATURE_DMA_GRANT)) {
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
+
+ if (!(asc->features & ASPEED_SMC_FEATURE_DMA_GRANT)) {
return true;
}
@@ -1334,6 +1047,7 @@ static void aspeed_smc_write(void *opaque, hwaddr addr, uint64_t data,
unsigned int size)
{
AspeedSMCState *s = ASPEED_SMC(opaque);
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
uint32_t value = data;
addr >>= 2;
@@ -1342,14 +1056,14 @@ static void aspeed_smc_write(void *opaque, hwaddr addr, uint64_t data,
if (addr == s->r_conf ||
(addr >= s->r_timings &&
- addr < s->r_timings + s->ctrl->nregs_timings) ||
+ addr < s->r_timings + asc->nregs_timings) ||
addr == s->r_ce_ctrl) {
s->regs[addr] = value;
} else if (addr >= s->r_ctrl0 && addr < s->r_ctrl0 + s->num_cs) {
int cs = addr - s->r_ctrl0;
aspeed_smc_flash_update_ctrl(&s->flashes[cs], value);
} else if (addr >= R_SEG_ADDR0 &&
- addr < R_SEG_ADDR0 + s->ctrl->max_peripherals) {
+ addr < R_SEG_ADDR0 + asc->max_peripherals) {
int cs = addr - R_SEG_ADDR0;
if (value != s->regs[R_SEG_ADDR0 + cs]) {
@@ -1359,19 +1073,19 @@ static void aspeed_smc_write(void *opaque, hwaddr addr, uint64_t data,
s->regs[addr] = value & 0xff;
} else if (addr == R_DUMMY_DATA) {
s->regs[addr] = value & 0xff;
- } else if (aspeed_smc_has_wdt_control(s) && addr == R_FMC_WDT2_CTRL) {
+ } else if (aspeed_smc_has_wdt_control(asc) && addr == R_FMC_WDT2_CTRL) {
s->regs[addr] = value & FMC_WDT2_CTRL_EN;
} else if (addr == R_INTR_CTRL) {
s->regs[addr] = value;
- } else if (aspeed_smc_has_dma(s) && addr == R_DMA_CTRL) {
- s->ctrl->dma_ctrl(s, value);
- } else if (aspeed_smc_has_dma(s) && addr == R_DMA_DRAM_ADDR &&
+ } else if (aspeed_smc_has_dma(asc) && addr == R_DMA_CTRL) {
+ asc->dma_ctrl(s, value);
+ } else if (aspeed_smc_has_dma(asc) && addr == R_DMA_DRAM_ADDR &&
aspeed_smc_dma_granted(s)) {
- s->regs[addr] = DMA_DRAM_ADDR(s, value);
- } else if (aspeed_smc_has_dma(s) && addr == R_DMA_FLASH_ADDR &&
+ s->regs[addr] = DMA_DRAM_ADDR(asc, value);
+ } else if (aspeed_smc_has_dma(asc) && addr == R_DMA_FLASH_ADDR &&
aspeed_smc_dma_granted(s)) {
- s->regs[addr] = DMA_FLASH_ADDR(s, value);
- } else if (aspeed_smc_has_dma(s) && addr == R_DMA_LEN &&
+ s->regs[addr] = DMA_FLASH_ADDR(asc, value);
+ } else if (aspeed_smc_has_dma(asc) && addr == R_DMA_LEN &&
aspeed_smc_dma_granted(s)) {
s->regs[addr] = DMA_LENGTH(value);
} else {
@@ -1407,24 +1121,22 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
{
SysBusDevice *sbd = SYS_BUS_DEVICE(dev);
AspeedSMCState *s = ASPEED_SMC(dev);
- AspeedSMCClass *mc = ASPEED_SMC_GET_CLASS(s);
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
int i;
char name[32];
hwaddr offset = 0;
- s->ctrl = mc->ctrl;
-
/* keep a copy under AspeedSMCState to speed up accesses */
- s->r_conf = s->ctrl->r_conf;
- s->r_ce_ctrl = s->ctrl->r_ce_ctrl;
- s->r_ctrl0 = s->ctrl->r_ctrl0;
- s->r_timings = s->ctrl->r_timings;
- s->conf_enable_w0 = s->ctrl->conf_enable_w0;
+ s->r_conf = asc->r_conf;
+ s->r_ce_ctrl = asc->r_ce_ctrl;
+ s->r_ctrl0 = asc->r_ctrl0;
+ s->r_timings = asc->r_timings;
+ s->conf_enable_w0 = asc->conf_enable_w0;
/* Enforce some real HW limits */
- if (s->num_cs > s->ctrl->max_peripherals) {
- aspeed_smc_error("num_cs cannot exceed: %d", s->ctrl->max_peripherals);
- s->num_cs = s->ctrl->max_peripherals;
+ if (s->num_cs > asc->max_peripherals) {
+ aspeed_smc_error("num_cs cannot exceed: %d", asc->max_peripherals);
+ s->num_cs = asc->max_peripherals;
}
/* DMA irq. Keep it first for the initialization in the SoC */
@@ -1441,7 +1153,7 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
/* The memory region for the controller registers */
memory_region_init_io(&s->mmio, OBJECT(s), &aspeed_smc_ops, s,
- TYPE_ASPEED_SMC, s->ctrl->nregs * 4);
+ TYPE_ASPEED_SMC, asc->nregs * 4);
sysbus_init_mmio(sbd, &s->mmio);
/*
@@ -1452,13 +1164,13 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
memory_region_init_io(&s->mmio_flash, OBJECT(s),
&aspeed_smc_flash_default_ops, s,
TYPE_ASPEED_SMC ".flash",
- s->ctrl->flash_window_size);
+ asc->flash_window_size);
memory_region_init_alias(&s->mmio_flash_alias, OBJECT(s),
TYPE_ASPEED_SMC ".flash",
- &s->mmio_flash, 0, s->ctrl->flash_window_size);
+ &s->mmio_flash, 0, asc->flash_window_size);
sysbus_init_mmio(sbd, &s->mmio_flash_alias);
- s->flashes = g_new0(AspeedSMCFlash, s->ctrl->max_peripherals);
+ s->flashes = g_new0(AspeedSMCFlash, asc->max_peripherals);
/*
* Let's create a sub memory region for each possible peripheral. All
@@ -1467,14 +1179,14 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
* module behind to handle the memory accesses. This depends on
* the board configuration.
*/
- for (i = 0; i < s->ctrl->max_peripherals; ++i) {
+ for (i = 0; i < asc->max_peripherals; ++i) {
AspeedSMCFlash *fl = &s->flashes[i];
snprintf(name, sizeof(name), TYPE_ASPEED_SMC ".flash.%d", i);
fl->id = i;
fl->controller = s;
- fl->size = s->ctrl->segments[i].size;
+ fl->size = asc->segments[i].size;
memory_region_init_io(&fl->mmio, OBJECT(s), &aspeed_smc_flash_ops,
fl, name, fl->size);
memory_region_add_subregion(&s->mmio_flash, offset, &fl->mmio);
@@ -1482,7 +1194,7 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
}
/* DMA support */
- if (aspeed_smc_has_dma(s)) {
+ if (aspeed_smc_has_dma(asc)) {
aspeed_smc_dma_setup(s, errp);
}
}
@@ -1510,13 +1222,11 @@ static Property aspeed_smc_properties[] = {
static void aspeed_smc_class_init(ObjectClass *klass, void *data)
{
DeviceClass *dc = DEVICE_CLASS(klass);
- AspeedSMCClass *mc = ASPEED_SMC_CLASS(klass);
dc->realize = aspeed_smc_realize;
dc->reset = aspeed_smc_reset;
device_class_set_props(dc, aspeed_smc_properties);
dc->vmsd = &vmstate_aspeed_smc;
- mc->ctrl = data;
}
static const TypeInfo aspeed_smc_info = {
@@ -1524,23 +1234,408 @@ static const TypeInfo aspeed_smc_info = {
.parent = TYPE_SYS_BUS_DEVICE,
.instance_size = sizeof(AspeedSMCState),
.class_size = sizeof(AspeedSMCClass),
+ .class_init = aspeed_smc_class_init,
.abstract = true,
};
-static void aspeed_smc_register_types(void)
+
+/*
+ * The Segment Registers of the AST2400 and AST2500 have a 8MB
+ * unit. The address range of a flash SPI peripheral is encoded with
+ * absolute addresses which should be part of the overall controller
+ * window.
+ */
+static uint32_t aspeed_smc_segment_to_reg(const AspeedSMCState *s,
+ const AspeedSegments *seg)
{
- int i;
+ uint32_t reg = 0;
+ reg |= ((seg->addr >> 23) & SEG_START_MASK) << SEG_START_SHIFT;
+ reg |= (((seg->addr + seg->size) >> 23) & SEG_END_MASK) << SEG_END_SHIFT;
+ return reg;
+}
- type_register_static(&aspeed_smc_info);
- for (i = 0; i < ARRAY_SIZE(controllers); ++i) {
- TypeInfo ti = {
- .name = controllers[i].name,
- .parent = TYPE_ASPEED_SMC,
- .class_init = aspeed_smc_class_init,
- .class_data = (void *)&controllers[i],
- };
- type_register(&ti);
+static void aspeed_smc_reg_to_segment(const AspeedSMCState *s,
+ uint32_t reg, AspeedSegments *seg)
+{
+ seg->addr = ((reg >> SEG_START_SHIFT) & SEG_START_MASK) << 23;
+ seg->size = (((reg >> SEG_END_SHIFT) & SEG_END_MASK) << 23) - seg->addr;
+}
+
+static const AspeedSegments aspeed_2400_smc_segments[] = {
+ { 0x10000000, 32 * MiB },
+};
+
+static void aspeed_2400_smc_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass);
+
+ dc->desc = "Aspeed 2400 SMC Controller";
+ asc->r_conf = R_CONF;
+ asc->r_ce_ctrl = R_CE_CTRL;
+ asc->r_ctrl0 = R_CTRL0;
+ asc->r_timings = R_TIMINGS;
+ asc->nregs_timings = 1;
+ asc->conf_enable_w0 = CONF_ENABLE_W0;
+ asc->max_peripherals = 1;
+ asc->segments = aspeed_2400_smc_segments;
+ asc->flash_window_base = 0x10000000;
+ asc->flash_window_size = 0x6000000;
+ asc->features = 0x0;
+ asc->nregs = ASPEED_SMC_R_SMC_MAX;
+ asc->segment_to_reg = aspeed_smc_segment_to_reg;
+ asc->reg_to_segment = aspeed_smc_reg_to_segment;
+ asc->dma_ctrl = aspeed_smc_dma_ctrl;
+}
+
+static const TypeInfo aspeed_2400_smc_info = {
+ .name = "aspeed.smc-ast2400",
+ .parent = TYPE_ASPEED_SMC,
+ .class_init = aspeed_2400_smc_class_init,
+};
+
+static const AspeedSegments aspeed_2400_fmc_segments[] = {
+ { 0x20000000, 64 * MiB }, /* start address is readonly */
+ { 0x24000000, 32 * MiB },
+ { 0x26000000, 32 * MiB },
+ { 0x28000000, 32 * MiB },
+ { 0x2A000000, 32 * MiB }
+};
+
+static void aspeed_2400_fmc_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass);
+
+ dc->desc = "Aspeed 2400 FMC Controller";
+ asc->r_conf = R_CONF;
+ asc->r_ce_ctrl = R_CE_CTRL;
+ asc->r_ctrl0 = R_CTRL0;
+ asc->r_timings = R_TIMINGS;
+ asc->nregs_timings = 1;
+ asc->conf_enable_w0 = CONF_ENABLE_W0;
+ asc->max_peripherals = 5;
+ asc->segments = aspeed_2400_fmc_segments;
+ asc->flash_window_base = 0x20000000;
+ asc->flash_window_size = 0x10000000;
+ asc->features = ASPEED_SMC_FEATURE_DMA;
+ asc->dma_flash_mask = 0x0FFFFFFC;
+ asc->dma_dram_mask = 0x1FFFFFFC;
+ asc->nregs = ASPEED_SMC_R_MAX;
+ asc->segment_to_reg = aspeed_smc_segment_to_reg;
+ asc->reg_to_segment = aspeed_smc_reg_to_segment;
+ asc->dma_ctrl = aspeed_smc_dma_ctrl;
+}
+
+static const TypeInfo aspeed_2400_fmc_info = {
+ .name = "aspeed.fmc-ast2400",
+ .parent = TYPE_ASPEED_SMC,
+ .class_init = aspeed_2400_fmc_class_init,
+};
+
+static const AspeedSegments aspeed_2400_spi1_segments[] = {
+ { 0x30000000, 64 * MiB },
+};
+
+static void aspeed_2400_spi1_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass);
+
+ dc->desc = "Aspeed 2400 SPI1 Controller";
+ asc->r_conf = R_SPI_CONF;
+ asc->r_ce_ctrl = 0xff;
+ asc->r_ctrl0 = R_SPI_CTRL0;
+ asc->r_timings = R_SPI_TIMINGS;
+ asc->nregs_timings = 1;
+ asc->conf_enable_w0 = SPI_CONF_ENABLE_W0;
+ asc->max_peripherals = 1;
+ asc->segments = aspeed_2400_spi1_segments;
+ asc->flash_window_base = 0x30000000;
+ asc->flash_window_size = 0x10000000;
+ asc->features = 0x0;
+ asc->nregs = ASPEED_SMC_R_SPI_MAX;
+ asc->segment_to_reg = aspeed_smc_segment_to_reg;
+ asc->reg_to_segment = aspeed_smc_reg_to_segment;
+ asc->dma_ctrl = aspeed_smc_dma_ctrl;
+}
+
+static const TypeInfo aspeed_2400_spi1_info = {
+ .name = "aspeed.spi1-ast2400",
+ .parent = TYPE_ASPEED_SMC,
+ .class_init = aspeed_2400_spi1_class_init,
+};
+
+static const AspeedSegments aspeed_2500_fmc_segments[] = {
+ { 0x20000000, 128 * MiB }, /* start address is readonly */
+ { 0x28000000, 32 * MiB },
+ { 0x2A000000, 32 * MiB },
+};
+
+static void aspeed_2500_fmc_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass);
+
+ dc->desc = "Aspeed 2600 FMC Controller";
+ asc->r_conf = R_CONF;
+ asc->r_ce_ctrl = R_CE_CTRL;
+ asc->r_ctrl0 = R_CTRL0;
+ asc->r_timings = R_TIMINGS;
+ asc->nregs_timings = 1;
+ asc->conf_enable_w0 = CONF_ENABLE_W0;
+ asc->max_peripherals = 3;
+ asc->segments = aspeed_2500_fmc_segments;
+ asc->flash_window_base = 0x20000000;
+ asc->flash_window_size = 0x10000000;
+ asc->features = ASPEED_SMC_FEATURE_DMA;
+ asc->dma_flash_mask = 0x0FFFFFFC;
+ asc->dma_dram_mask = 0x3FFFFFFC;
+ asc->nregs = ASPEED_SMC_R_MAX;
+ asc->segment_to_reg = aspeed_smc_segment_to_reg;
+ asc->reg_to_segment = aspeed_smc_reg_to_segment;
+ asc->dma_ctrl = aspeed_smc_dma_ctrl;
+}
+
+static const TypeInfo aspeed_2500_fmc_info = {
+ .name = "aspeed.fmc-ast2500",
+ .parent = TYPE_ASPEED_SMC,
+ .class_init = aspeed_2500_fmc_class_init,
+};
+
+static const AspeedSegments aspeed_2500_spi1_segments[] = {
+ { 0x30000000, 32 * MiB }, /* start address is readonly */
+ { 0x32000000, 96 * MiB }, /* end address is readonly */
+};
+
+static void aspeed_2500_spi1_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass);
+
+ dc->desc = "Aspeed 2600 SPI1 Controller";
+ asc->r_conf = R_CONF;
+ asc->r_ce_ctrl = R_CE_CTRL;
+ asc->r_ctrl0 = R_CTRL0;
+ asc->r_timings = R_TIMINGS;
+ asc->nregs_timings = 1;
+ asc->conf_enable_w0 = CONF_ENABLE_W0;
+ asc->max_peripherals = 2;
+ asc->segments = aspeed_2500_spi1_segments;
+ asc->flash_window_base = 0x30000000;
+ asc->flash_window_size = 0x8000000;
+ asc->features = 0x0;
+ asc->nregs = ASPEED_SMC_R_MAX;
+ asc->segment_to_reg = aspeed_smc_segment_to_reg;
+ asc->reg_to_segment = aspeed_smc_reg_to_segment;
+ asc->dma_ctrl = aspeed_smc_dma_ctrl;
+}
+
+static const TypeInfo aspeed_2500_spi1_info = {
+ .name = "aspeed.spi1-ast2500",
+ .parent = TYPE_ASPEED_SMC,
+ .class_init = aspeed_2500_spi1_class_init,
+};
+
+static const AspeedSegments aspeed_2500_spi2_segments[] = {
+ { 0x38000000, 32 * MiB }, /* start address is readonly */
+ { 0x3A000000, 96 * MiB }, /* end address is readonly */
+};
+
+static void aspeed_2500_spi2_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass);
+
+ dc->desc = "Aspeed 2600 SPI2 Controller";
+ asc->r_conf = R_CONF;
+ asc->r_ce_ctrl = R_CE_CTRL;
+ asc->r_ctrl0 = R_CTRL0;
+ asc->r_timings = R_TIMINGS;
+ asc->nregs_timings = 1;
+ asc->conf_enable_w0 = CONF_ENABLE_W0;
+ asc->max_peripherals = 2;
+ asc->segments = aspeed_2500_spi2_segments;
+ asc->flash_window_base = 0x38000000;
+ asc->flash_window_size = 0x8000000;
+ asc->features = 0x0;
+ asc->nregs = ASPEED_SMC_R_MAX;
+ asc->segment_to_reg = aspeed_smc_segment_to_reg;
+ asc->reg_to_segment = aspeed_smc_reg_to_segment;
+ asc->dma_ctrl = aspeed_smc_dma_ctrl;
+}
+
+static const TypeInfo aspeed_2500_spi2_info = {
+ .name = "aspeed.spi2-ast2500",
+ .parent = TYPE_ASPEED_SMC,
+ .class_init = aspeed_2500_spi2_class_init,
+};
+
+/*
+ * The Segment Registers of the AST2600 have a 1MB unit. The address
+ * range of a flash SPI peripheral is encoded with offsets in the overall
+ * controller window. The previous SoC AST2400 and AST2500 used
+ * absolute addresses. Only bits [27:20] are relevant and the end
+ * address is an upper bound limit.
+ */
+#define AST2600_SEG_ADDR_MASK 0x0ff00000
+
+static uint32_t aspeed_2600_smc_segment_to_reg(const AspeedSMCState *s,
+ const AspeedSegments *seg)
+{
+ uint32_t reg = 0;
+
+ /* Disabled segments have a nil register */
+ if (!seg->size) {
+ return 0;
+ }
+
+ reg |= (seg->addr & AST2600_SEG_ADDR_MASK) >> 16; /* start offset */
+ reg |= (seg->addr + seg->size - 1) & AST2600_SEG_ADDR_MASK; /* end offset */
+ return reg;
+}
+
+static void aspeed_2600_smc_reg_to_segment(const AspeedSMCState *s,
+ uint32_t reg, AspeedSegments *seg)
+{
+ uint32_t start_offset = (reg << 16) & AST2600_SEG_ADDR_MASK;
+ uint32_t end_offset = reg & AST2600_SEG_ADDR_MASK;
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
+
+ if (reg) {
+ seg->addr = asc->flash_window_base + start_offset;
+ seg->size = end_offset + MiB - start_offset;
+ } else {
+ seg->addr = asc->flash_window_base;
+ seg->size = 0;
}
}
+static const AspeedSegments aspeed_2600_fmc_segments[] = {
+ { 0x0, 128 * MiB }, /* start address is readonly */
+ { 128 * MiB, 128 * MiB }, /* default is disabled but needed for -kernel */
+ { 0x0, 0 }, /* disabled */
+};
+
+static void aspeed_2600_fmc_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass);
+
+ dc->desc = "Aspeed 2600 FMC Controller";
+ asc->r_conf = R_CONF;
+ asc->r_ce_ctrl = R_CE_CTRL;
+ asc->r_ctrl0 = R_CTRL0;
+ asc->r_timings = R_TIMINGS;
+ asc->nregs_timings = 1;
+ asc->conf_enable_w0 = CONF_ENABLE_W0;
+ asc->max_peripherals = 3;
+ asc->segments = aspeed_2600_fmc_segments;
+ asc->flash_window_base = 0x20000000;
+ asc->flash_window_size = 0x10000000;
+ asc->features = ASPEED_SMC_FEATURE_DMA |
+ ASPEED_SMC_FEATURE_WDT_CONTROL;
+ asc->dma_flash_mask = 0x0FFFFFFC;
+ asc->dma_dram_mask = 0x3FFFFFFC;
+ asc->nregs = ASPEED_SMC_R_MAX;
+ asc->segment_to_reg = aspeed_2600_smc_segment_to_reg;
+ asc->reg_to_segment = aspeed_2600_smc_reg_to_segment;
+ asc->dma_ctrl = aspeed_2600_smc_dma_ctrl;
+}
+
+static const TypeInfo aspeed_2600_fmc_info = {
+ .name = "aspeed.fmc-ast2600",
+ .parent = TYPE_ASPEED_SMC,
+ .class_init = aspeed_2600_fmc_class_init,
+};
+
+static const AspeedSegments aspeed_2600_spi1_segments[] = {
+ { 0x0, 128 * MiB }, /* start address is readonly */
+ { 0x0, 0 }, /* disabled */
+};
+
+static void aspeed_2600_spi1_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass);
+
+ dc->desc = "Aspeed 2600 SPI1 Controller";
+ asc->r_conf = R_CONF;
+ asc->r_ce_ctrl = R_CE_CTRL;
+ asc->r_ctrl0 = R_CTRL0;
+ asc->r_timings = R_TIMINGS;
+ asc->nregs_timings = 2;
+ asc->conf_enable_w0 = CONF_ENABLE_W0;
+ asc->max_peripherals = 2;
+ asc->segments = aspeed_2600_spi1_segments;
+ asc->flash_window_base = 0x30000000;
+ asc->flash_window_size = 0x10000000;
+ asc->features = ASPEED_SMC_FEATURE_DMA |
+ ASPEED_SMC_FEATURE_DMA_GRANT;
+ asc->dma_flash_mask = 0x0FFFFFFC;
+ asc->dma_dram_mask = 0x3FFFFFFC;
+ asc->nregs = ASPEED_SMC_R_MAX;
+ asc->segment_to_reg = aspeed_2600_smc_segment_to_reg;
+ asc->reg_to_segment = aspeed_2600_smc_reg_to_segment;
+ asc->dma_ctrl = aspeed_2600_smc_dma_ctrl;
+}
+
+static const TypeInfo aspeed_2600_spi1_info = {
+ .name = "aspeed.spi1-ast2600",
+ .parent = TYPE_ASPEED_SMC,
+ .class_init = aspeed_2600_spi1_class_init,
+};
+
+static const AspeedSegments aspeed_2600_spi2_segments[] = {
+ { 0x0, 128 * MiB }, /* start address is readonly */
+ { 0x0, 0 }, /* disabled */
+ { 0x0, 0 }, /* disabled */
+};
+
+static void aspeed_2600_spi2_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedSMCClass *asc = ASPEED_SMC_CLASS(klass);
+
+ dc->desc = "Aspeed 2600 SPI2 Controller";
+ asc->r_conf = R_CONF;
+ asc->r_ce_ctrl = R_CE_CTRL;
+ asc->r_ctrl0 = R_CTRL0;
+ asc->r_timings = R_TIMINGS;
+ asc->nregs_timings = 3;
+ asc->conf_enable_w0 = CONF_ENABLE_W0;
+ asc->max_peripherals = 3;
+ asc->segments = aspeed_2600_spi2_segments;
+ asc->flash_window_base = 0x50000000;
+ asc->flash_window_size = 0x10000000;
+ asc->features = ASPEED_SMC_FEATURE_DMA |
+ ASPEED_SMC_FEATURE_DMA_GRANT;
+ asc->dma_flash_mask = 0x0FFFFFFC;
+ asc->dma_dram_mask = 0x3FFFFFFC;
+ asc->nregs = ASPEED_SMC_R_MAX;
+ asc->segment_to_reg = aspeed_2600_smc_segment_to_reg;
+ asc->reg_to_segment = aspeed_2600_smc_reg_to_segment;
+ asc->dma_ctrl = aspeed_2600_smc_dma_ctrl;
+}
+
+static const TypeInfo aspeed_2600_spi2_info = {
+ .name = "aspeed.spi2-ast2600",
+ .parent = TYPE_ASPEED_SMC,
+ .class_init = aspeed_2600_spi2_class_init,
+};
+
+static void aspeed_smc_register_types(void)
+{
+ type_register_static(&aspeed_smc_info);
+ type_register_static(&aspeed_2400_smc_info);
+ type_register_static(&aspeed_2400_fmc_info);
+ type_register_static(&aspeed_2400_spi1_info);
+ type_register_static(&aspeed_2500_fmc_info);
+ type_register_static(&aspeed_2500_spi1_info);
+ type_register_static(&aspeed_2500_spi2_info);
+ type_register_static(&aspeed_2600_fmc_info);
+ type_register_static(&aspeed_2600_spi1_info);
+ type_register_static(&aspeed_2600_spi2_info);
+}
+
type_init(aspeed_smc_register_types)
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 05/18] aspeed/smc: Remove the 'flash' attribute from AspeedSMCFlash
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (3 preceding siblings ...)
2021-10-12 7:37 ` [PULL 04/18] aspeed/smc: Drop AspeedSMCController structure Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 06/18] aspeed/smc: Remove the 'size' " Cédric Le Goater
` (13 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Philippe Mathieu-Daudé, qemu-devel, qemu-arm,
Cédric Le Goater, Joel Stanley
There is no need to keep a reference of the flash qdev in the AspeedSMCFlash
state: the SPI bus takes ownership and will release its resources. Remove
AspeedSMCFlash::flash.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/ssi/aspeed_smc.h | 1 -
hw/arm/aspeed.c | 11 +++++------
2 files changed, 5 insertions(+), 7 deletions(-)
diff --git a/include/hw/ssi/aspeed_smc.h b/include/hw/ssi/aspeed_smc.h
index 0ea536a44c3a..f32f66f9a838 100644
--- a/include/hw/ssi/aspeed_smc.h
+++ b/include/hw/ssi/aspeed_smc.h
@@ -37,7 +37,6 @@ typedef struct AspeedSMCFlash {
uint32_t size;
MemoryRegion mmio;
- DeviceState *flash;
} AspeedSMCFlash;
#define TYPE_ASPEED_SMC "aspeed.smc"
diff --git a/hw/arm/aspeed.c b/hw/arm/aspeed.c
index ba5f1dc5af78..854413594d9e 100644
--- a/hw/arm/aspeed.c
+++ b/hw/arm/aspeed.c
@@ -274,18 +274,17 @@ static void aspeed_board_init_flashes(AspeedSMCState *s,
int i ;
for (i = 0; i < s->num_cs; ++i) {
- AspeedSMCFlash *fl = &s->flashes[i];
DriveInfo *dinfo = drive_get_next(IF_MTD);
qemu_irq cs_line;
+ DeviceState *dev;
- fl->flash = qdev_new(flashtype);
+ dev = qdev_new(flashtype);
if (dinfo) {
- qdev_prop_set_drive(fl->flash, "drive",
- blk_by_legacy_dinfo(dinfo));
+ qdev_prop_set_drive(dev, "drive", blk_by_legacy_dinfo(dinfo));
}
- qdev_realize_and_unref(fl->flash, BUS(s->spi), &error_fatal);
+ qdev_realize_and_unref(dev, BUS(s->spi), &error_fatal);
- cs_line = qdev_get_gpio_in_named(fl->flash, SSI_GPIO_CS, 0);
+ cs_line = qdev_get_gpio_in_named(dev, SSI_GPIO_CS, 0);
sysbus_connect_irq(SYS_BUS_DEVICE(s), i + 1, cs_line);
}
}
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 06/18] aspeed/smc: Remove the 'size' attribute from AspeedSMCFlash
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (4 preceding siblings ...)
2021-10-12 7:37 ` [PULL 05/18] aspeed/smc: Remove the 'flash' attribute from AspeedSMCFlash Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 07/18] aspeed/smc: Rename AspeedSMCFlash 'id' to 'cs' Cédric Le Goater
` (12 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Philippe Mathieu-Daudé, qemu-devel, qemu-arm,
Cédric Le Goater, Joel Stanley
AspeedSMCFlash::size is only used to compute the initial size of the
boot_rom region. Not very useful, so directly call memory_region_size()
instead.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/ssi/aspeed_smc.h | 1 -
hw/arm/aspeed.c | 7 ++++---
hw/ssi/aspeed_smc.c | 5 ++---
3 files changed, 6 insertions(+), 7 deletions(-)
diff --git a/include/hw/ssi/aspeed_smc.h b/include/hw/ssi/aspeed_smc.h
index f32f66f9a838..097bb6aaf5f8 100644
--- a/include/hw/ssi/aspeed_smc.h
+++ b/include/hw/ssi/aspeed_smc.h
@@ -34,7 +34,6 @@ typedef struct AspeedSMCFlash {
struct AspeedSMCState *controller;
uint8_t id;
- uint32_t size;
MemoryRegion mmio;
} AspeedSMCFlash;
diff --git a/hw/arm/aspeed.c b/hw/arm/aspeed.c
index 854413594d9e..f5916e81262e 100644
--- a/hw/arm/aspeed.c
+++ b/hw/arm/aspeed.c
@@ -376,6 +376,7 @@ static void aspeed_machine_init(MachineState *machine)
if (drive0) {
AspeedSMCFlash *fl = &bmc->soc.fmc.flashes[0];
MemoryRegion *boot_rom = g_new(MemoryRegion, 1);
+ uint64_t size = memory_region_size(&fl->mmio);
/*
* create a ROM region using the default mapping window size of
@@ -385,15 +386,15 @@ static void aspeed_machine_init(MachineState *machine)
*/
if (ASPEED_MACHINE(machine)->mmio_exec) {
memory_region_init_alias(boot_rom, NULL, "aspeed.boot_rom",
- &fl->mmio, 0, fl->size);
+ &fl->mmio, 0, size);
memory_region_add_subregion(get_system_memory(), FIRMWARE_ADDR,
boot_rom);
} else {
memory_region_init_rom(boot_rom, NULL, "aspeed.boot_rom",
- fl->size, &error_abort);
+ size, &error_abort);
memory_region_add_subregion(get_system_memory(), FIRMWARE_ADDR,
boot_rom);
- write_boot_rom(drive0, FIRMWARE_ADDR, fl->size, &error_abort);
+ write_boot_rom(drive0, FIRMWARE_ADDR, size, &error_abort);
}
}
diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index 5466be631719..3e4221311a6d 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -1186,11 +1186,10 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
fl->id = i;
fl->controller = s;
- fl->size = asc->segments[i].size;
memory_region_init_io(&fl->mmio, OBJECT(s), &aspeed_smc_flash_ops,
- fl, name, fl->size);
+ fl, name, asc->segments[i].size);
memory_region_add_subregion(&s->mmio_flash, offset, &fl->mmio);
- offset += fl->size;
+ offset += asc->segments[i].size;
}
/* DMA support */
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 07/18] aspeed/smc: Rename AspeedSMCFlash 'id' to 'cs'
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (5 preceding siblings ...)
2021-10-12 7:37 ` [PULL 06/18] aspeed/smc: Remove the 'size' " Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 08/18] aspeed/smc: QOMify AspeedSMCFlash Cédric Le Goater
` (11 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Philippe Mathieu-Daudé, qemu-devel, qemu-arm,
Cédric Le Goater, Joel Stanley
'cs' is a more appropriate name to index SPI flash devices.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/ssi/aspeed_smc.h | 2 +-
hw/ssi/aspeed_smc.c | 30 +++++++++++++++---------------
2 files changed, 16 insertions(+), 16 deletions(-)
diff --git a/include/hw/ssi/aspeed_smc.h b/include/hw/ssi/aspeed_smc.h
index 097bb6aaf5f8..40b6926b3e02 100644
--- a/include/hw/ssi/aspeed_smc.h
+++ b/include/hw/ssi/aspeed_smc.h
@@ -33,7 +33,7 @@ struct AspeedSMCState;
typedef struct AspeedSMCFlash {
struct AspeedSMCState *controller;
- uint8_t id;
+ uint8_t cs;
MemoryRegion mmio;
} AspeedSMCFlash;
diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index 3e4221311a6d..643cde832396 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -352,20 +352,20 @@ static inline int aspeed_smc_flash_mode(const AspeedSMCFlash *fl)
{
const AspeedSMCState *s = fl->controller;
- return s->regs[s->r_ctrl0 + fl->id] & CTRL_CMD_MODE_MASK;
+ return s->regs[s->r_ctrl0 + fl->cs] & CTRL_CMD_MODE_MASK;
}
static inline bool aspeed_smc_is_writable(const AspeedSMCFlash *fl)
{
const AspeedSMCState *s = fl->controller;
- return s->regs[s->r_conf] & (1 << (s->conf_enable_w0 + fl->id));
+ return s->regs[s->r_conf] & (1 << (s->conf_enable_w0 + fl->cs));
}
static inline int aspeed_smc_flash_cmd(const AspeedSMCFlash *fl)
{
const AspeedSMCState *s = fl->controller;
- int cmd = (s->regs[s->r_ctrl0 + fl->id] >> CTRL_CMD_SHIFT) & CTRL_CMD_MASK;
+ int cmd = (s->regs[s->r_ctrl0 + fl->cs] >> CTRL_CMD_SHIFT) & CTRL_CMD_MASK;
/*
* In read mode, the default SPI command is READ (0x3). In other
@@ -393,7 +393,7 @@ static inline int aspeed_smc_flash_is_4byte(const AspeedSMCFlash *fl)
if (asc->segments == aspeed_2400_spi1_segments) {
return s->regs[s->r_ctrl0] & CTRL_AST2400_SPI_4BYTE;
} else {
- return s->regs[s->r_ce_ctrl] & (1 << (CTRL_EXTENDED0 + fl->id));
+ return s->regs[s->r_ce_ctrl] & (1 << (CTRL_EXTENDED0 + fl->cs));
}
}
@@ -401,9 +401,9 @@ static void aspeed_smc_flash_do_select(AspeedSMCFlash *fl, bool unselect)
{
AspeedSMCState *s = fl->controller;
- trace_aspeed_smc_flash_select(fl->id, unselect ? "un" : "");
+ trace_aspeed_smc_flash_select(fl->cs, unselect ? "un" : "");
- qemu_set_irq(s->cs_lines[fl->id], unselect);
+ qemu_set_irq(s->cs_lines[fl->cs], unselect);
}
static void aspeed_smc_flash_select(AspeedSMCFlash *fl)
@@ -423,11 +423,11 @@ static uint32_t aspeed_smc_check_segment_addr(const AspeedSMCFlash *fl,
AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
AspeedSegments seg;
- asc->reg_to_segment(s, s->regs[R_SEG_ADDR0 + fl->id], &seg);
+ asc->reg_to_segment(s, s->regs[R_SEG_ADDR0 + fl->cs], &seg);
if ((addr % seg.size) != addr) {
aspeed_smc_error("invalid address 0x%08x for CS%d segment : "
"[ 0x%"HWADDR_PRIx" - 0x%"HWADDR_PRIx" ]",
- addr, fl->id, seg.addr, seg.addr + seg.size);
+ addr, fl->cs, seg.addr, seg.addr + seg.size);
addr %= seg.size;
}
@@ -437,7 +437,7 @@ static uint32_t aspeed_smc_check_segment_addr(const AspeedSMCFlash *fl,
static int aspeed_smc_flash_dummies(const AspeedSMCFlash *fl)
{
const AspeedSMCState *s = fl->controller;
- uint32_t r_ctrl0 = s->regs[s->r_ctrl0 + fl->id];
+ uint32_t r_ctrl0 = s->regs[s->r_ctrl0 + fl->cs];
uint32_t dummy_high = (r_ctrl0 >> CTRL_DUMMY_HIGH_SHIFT) & 0x1;
uint32_t dummy_low = (r_ctrl0 >> CTRL_DUMMY_LOW_SHIFT) & 0x3;
uint32_t dummies = ((dummy_high << 2) | dummy_low) * 8;
@@ -506,7 +506,7 @@ static uint64_t aspeed_smc_flash_read(void *opaque, hwaddr addr, unsigned size)
aspeed_smc_error("invalid flash mode %d", aspeed_smc_flash_mode(fl));
}
- trace_aspeed_smc_flash_read(fl->id, addr, size, ret,
+ trace_aspeed_smc_flash_read(fl->cs, addr, size, ret,
aspeed_smc_flash_mode(fl));
return ret;
}
@@ -563,7 +563,7 @@ static bool aspeed_smc_do_snoop(AspeedSMCFlash *fl, uint64_t data,
AspeedSMCState *s = fl->controller;
uint8_t addr_width = aspeed_smc_flash_is_4byte(fl) ? 4 : 3;
- trace_aspeed_smc_do_snoop(fl->id, s->snoop_index, s->snoop_dummies,
+ trace_aspeed_smc_do_snoop(fl->cs, s->snoop_index, s->snoop_dummies,
(uint8_t) data & 0xff);
if (s->snoop_index == SNOOP_OFF) {
@@ -616,7 +616,7 @@ static void aspeed_smc_flash_write(void *opaque, hwaddr addr, uint64_t data,
AspeedSMCState *s = fl->controller;
int i;
- trace_aspeed_smc_flash_write(fl->id, addr, size, data,
+ trace_aspeed_smc_flash_write(fl->cs, addr, size, data,
aspeed_smc_flash_mode(fl));
if (!aspeed_smc_is_writable(fl)) {
@@ -668,12 +668,12 @@ static void aspeed_smc_flash_update_ctrl(AspeedSMCFlash *fl, uint32_t value)
unselect = (value & CTRL_CMD_MODE_MASK) != CTRL_USERMODE;
/* A change of CTRL_CE_STOP_ACTIVE from 0 to 1, unselects the CS */
- if (!(s->regs[s->r_ctrl0 + fl->id] & CTRL_CE_STOP_ACTIVE) &&
+ if (!(s->regs[s->r_ctrl0 + fl->cs] & CTRL_CE_STOP_ACTIVE) &&
value & CTRL_CE_STOP_ACTIVE) {
unselect = true;
}
- s->regs[s->r_ctrl0 + fl->id] = value;
+ s->regs[s->r_ctrl0 + fl->cs] = value;
s->snoop_index = unselect ? SNOOP_OFF : SNOOP_START;
@@ -1184,7 +1184,7 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
snprintf(name, sizeof(name), TYPE_ASPEED_SMC ".flash.%d", i);
- fl->id = i;
+ fl->cs = i;
fl->controller = s;
memory_region_init_io(&fl->mmio, OBJECT(s), &aspeed_smc_flash_ops,
fl, name, asc->segments[i].size);
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 08/18] aspeed/smc: QOMify AspeedSMCFlash
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (6 preceding siblings ...)
2021-10-12 7:37 ` [PULL 07/18] aspeed/smc: Rename AspeedSMCFlash 'id' to 'cs' Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 09/18] aspeed/smc: Add default reset values Cédric Le Goater
` (10 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Philippe Mathieu-Daudé, qemu-devel, qemu-arm,
Cédric Le Goater, Joel Stanley
AspeedSMCFlash is a small structure representing the AHB memory window
through which the contents of a flash device can be accessed with MMIOs.
Introduce an AspeedSMCFlash SysBusDevice model and attach the associated
memory region to the newly instantiated objects.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/ssi/aspeed_smc.h | 13 +++++--
hw/ssi/aspeed_smc.c | 76 +++++++++++++++++++++++++++++++++----
2 files changed, 77 insertions(+), 12 deletions(-)
diff --git a/include/hw/ssi/aspeed_smc.h b/include/hw/ssi/aspeed_smc.h
index 40b6926b3e02..ee943228b96f 100644
--- a/include/hw/ssi/aspeed_smc.h
+++ b/include/hw/ssi/aspeed_smc.h
@@ -30,18 +30,23 @@
#include "qom/object.h"
struct AspeedSMCState;
-typedef struct AspeedSMCFlash {
- struct AspeedSMCState *controller;
+#define TYPE_ASPEED_SMC_FLASH "aspeed.smc.flash"
+OBJECT_DECLARE_SIMPLE_TYPE(AspeedSMCFlash, ASPEED_SMC_FLASH)
+struct AspeedSMCFlash {
+ SysBusDevice parent_obj;
+
+ struct AspeedSMCState *controller;
uint8_t cs;
MemoryRegion mmio;
-} AspeedSMCFlash;
+};
#define TYPE_ASPEED_SMC "aspeed.smc"
OBJECT_DECLARE_TYPE(AspeedSMCState, AspeedSMCClass, ASPEED_SMC)
#define ASPEED_SMC_R_MAX (0x100 / 4)
+#define ASPEED_SMC_CS_MAX 5
struct AspeedSMCState {
SysBusDevice parent_obj;
@@ -72,7 +77,7 @@ struct AspeedSMCState {
MemoryRegion *dram_mr;
AddressSpace dram_as;
- AspeedSMCFlash *flashes;
+ AspeedSMCFlash flashes[ASPEED_SMC_CS_MAX];
uint8_t snoop_index;
uint8_t snoop_dummies;
diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index 643cde832396..c534e9bf87ee 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -1101,6 +1101,18 @@ static const MemoryRegionOps aspeed_smc_ops = {
.endianness = DEVICE_LITTLE_ENDIAN,
};
+static void aspeed_smc_instance_init(Object *obj)
+{
+ AspeedSMCState *s = ASPEED_SMC(obj);
+ AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
+ int i;
+
+ for (i = 0; i < asc->max_peripherals; i++) {
+ object_initialize_child(obj, "flash[*]", &s->flashes[i],
+ TYPE_ASPEED_SMC_FLASH);
+ }
+}
+
/*
* Initialize the custom address spaces for DMAs
*/
@@ -1123,7 +1135,6 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
AspeedSMCState *s = ASPEED_SMC(dev);
AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
int i;
- char name[32];
hwaddr offset = 0;
/* keep a copy under AspeedSMCState to speed up accesses */
@@ -1170,8 +1181,6 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
&s->mmio_flash, 0, asc->flash_window_size);
sysbus_init_mmio(sbd, &s->mmio_flash_alias);
- s->flashes = g_new0(AspeedSMCFlash, asc->max_peripherals);
-
/*
* Let's create a sub memory region for each possible peripheral. All
* have a configurable memory segment in the overall flash mapping
@@ -1182,12 +1191,17 @@ static void aspeed_smc_realize(DeviceState *dev, Error **errp)
for (i = 0; i < asc->max_peripherals; ++i) {
AspeedSMCFlash *fl = &s->flashes[i];
- snprintf(name, sizeof(name), TYPE_ASPEED_SMC ".flash.%d", i);
+ if (!object_property_set_link(OBJECT(fl), "controller", OBJECT(s),
+ errp)) {
+ return;
+ }
+ if (!object_property_set_uint(OBJECT(fl), "cs", i, errp)) {
+ return;
+ }
+ if (!sysbus_realize(SYS_BUS_DEVICE(fl), errp)) {
+ return;
+ }
- fl->cs = i;
- fl->controller = s;
- memory_region_init_io(&fl->mmio, OBJECT(s), &aspeed_smc_flash_ops,
- fl, name, asc->segments[i].size);
memory_region_add_subregion(&s->mmio_flash, offset, &fl->mmio);
offset += asc->segments[i].size;
}
@@ -1231,12 +1245,57 @@ static void aspeed_smc_class_init(ObjectClass *klass, void *data)
static const TypeInfo aspeed_smc_info = {
.name = TYPE_ASPEED_SMC,
.parent = TYPE_SYS_BUS_DEVICE,
+ .instance_init = aspeed_smc_instance_init,
.instance_size = sizeof(AspeedSMCState),
.class_size = sizeof(AspeedSMCClass),
.class_init = aspeed_smc_class_init,
.abstract = true,
};
+static void aspeed_smc_flash_realize(DeviceState *dev, Error **errp)
+{
+ AspeedSMCFlash *s = ASPEED_SMC_FLASH(dev);
+ AspeedSMCClass *asc;
+ g_autofree char *name = g_strdup_printf(TYPE_ASPEED_SMC_FLASH ".%d", s->cs);
+
+ if (!s->controller) {
+ error_setg(errp, TYPE_ASPEED_SMC_FLASH ": 'controller' link not set");
+ return;
+ }
+
+ asc = ASPEED_SMC_GET_CLASS(s->controller);
+
+ /*
+ * Use the default segment value to size the memory region. This
+ * can be changed by FW at runtime.
+ */
+ memory_region_init_io(&s->mmio, OBJECT(s), &aspeed_smc_flash_ops,
+ s, name, asc->segments[s->cs].size);
+ sysbus_init_mmio(SYS_BUS_DEVICE(dev), &s->mmio);
+}
+
+static Property aspeed_smc_flash_properties[] = {
+ DEFINE_PROP_UINT8("cs", AspeedSMCFlash, cs, 0),
+ DEFINE_PROP_LINK("controller", AspeedSMCFlash, controller, TYPE_ASPEED_SMC,
+ AspeedSMCState *),
+ DEFINE_PROP_END_OF_LIST(),
+};
+
+static void aspeed_smc_flash_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+
+ dc->desc = "Aspeed SMC Flash device region";
+ dc->realize = aspeed_smc_flash_realize;
+ device_class_set_props(dc, aspeed_smc_flash_properties);
+}
+
+static const TypeInfo aspeed_smc_flash_info = {
+ .name = TYPE_ASPEED_SMC_FLASH,
+ .parent = TYPE_SYS_BUS_DEVICE,
+ .instance_size = sizeof(AspeedSMCFlash),
+ .class_init = aspeed_smc_flash_class_init,
+};
/*
* The Segment Registers of the AST2400 and AST2500 have a 8MB
@@ -1625,6 +1684,7 @@ static const TypeInfo aspeed_2600_spi2_info = {
static void aspeed_smc_register_types(void)
{
+ type_register_static(&aspeed_smc_flash_info);
type_register_static(&aspeed_smc_info);
type_register_static(&aspeed_2400_smc_info);
type_register_static(&aspeed_2400_fmc_info);
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 09/18] aspeed/smc: Add default reset values
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (7 preceding siblings ...)
2021-10-12 7:37 ` [PULL 08/18] aspeed/smc: QOMify AspeedSMCFlash Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 10/18] aspeed/smc: Introduce a new addr_width() class handler Cédric Le Goater
` (9 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Cédric Le Goater, qemu-arm, Joel Stanley,
qemu-devel
This simplifies the reset handler and has the benefit to remove some
"bad" use of the segments array as an identifier of the controller model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/ssi/aspeed_smc.h | 1 +
hw/ssi/aspeed_smc.c | 52 +++++++++++++++++++------------------
2 files changed, 28 insertions(+), 25 deletions(-)
diff --git a/include/hw/ssi/aspeed_smc.h b/include/hw/ssi/aspeed_smc.h
index ee943228b96f..a1ca0e65c405 100644
--- a/include/hw/ssi/aspeed_smc.h
+++ b/include/hw/ssi/aspeed_smc.h
@@ -98,6 +98,7 @@ struct AspeedSMCClass {
uint8_t nregs_timings;
uint8_t conf_enable_w0;
uint8_t max_peripherals;
+ const uint32_t *resets;
const AspeedSegments *segments;
hwaddr flash_window_base;
uint32_t flash_window_size;
diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index c534e9bf87ee..8cc7ccf45591 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -196,12 +196,9 @@
* controller. These can be changed when board is initialized with the
* Segment Address Registers.
*/
-static const AspeedSegments aspeed_2400_fmc_segments[];
static const AspeedSegments aspeed_2400_spi1_segments[];
-static const AspeedSegments aspeed_2500_fmc_segments[];
static const AspeedSegments aspeed_2500_spi1_segments[];
static const AspeedSegments aspeed_2500_spi2_segments[];
-static const AspeedSegments aspeed_2600_fmc_segments[];
#define ASPEED_SMC_FEATURE_DMA 0x1
#define ASPEED_SMC_FEATURE_DMA_GRANT 0x2
@@ -686,7 +683,11 @@ static void aspeed_smc_reset(DeviceState *d)
AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
int i;
- memset(s->regs, 0, sizeof s->regs);
+ if (asc->resets) {
+ memcpy(s->regs, asc->resets, sizeof s->regs);
+ } else {
+ memset(s->regs, 0, sizeof s->regs);
+ }
/* Unselect all peripherals */
for (i = 0; i < s->num_cs; ++i) {
@@ -700,27 +701,6 @@ static void aspeed_smc_reset(DeviceState *d)
asc->segment_to_reg(s, &asc->segments[i]));
}
- /* HW strapping flash type for the AST2600 controllers */
- if (asc->segments == aspeed_2600_fmc_segments) {
- /* flash type is fixed to SPI for all */
- s->regs[s->r_conf] |= (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0);
- s->regs[s->r_conf] |= (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE1);
- s->regs[s->r_conf] |= (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE2);
- }
-
- /* HW strapping flash type for FMC controllers */
- if (asc->segments == aspeed_2500_fmc_segments) {
- /* flash type is fixed to SPI for CE0 and CE1 */
- s->regs[s->r_conf] |= (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0);
- s->regs[s->r_conf] |= (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE1);
- }
-
- /* HW strapping for AST2400 FMC controllers (SCU70). Let's use the
- * configuration of the palmetto-bmc machine */
- if (asc->segments == aspeed_2400_fmc_segments) {
- s->regs[s->r_conf] |= (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0);
- }
-
s->snoop_index = SNOOP_OFF;
s->snoop_dummies = 0;
}
@@ -1352,6 +1332,14 @@ static const TypeInfo aspeed_2400_smc_info = {
.class_init = aspeed_2400_smc_class_init,
};
+static const uint32_t aspeed_2400_fmc_resets[ASPEED_SMC_R_MAX] = {
+ /*
+ * CE0 and CE1 types are HW strapped in SCU70. Do it here to
+ * simplify the model.
+ */
+ [R_CONF] = CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0,
+};
+
static const AspeedSegments aspeed_2400_fmc_segments[] = {
{ 0x20000000, 64 * MiB }, /* start address is readonly */
{ 0x24000000, 32 * MiB },
@@ -1374,6 +1362,7 @@ static void aspeed_2400_fmc_class_init(ObjectClass *klass, void *data)
asc->conf_enable_w0 = CONF_ENABLE_W0;
asc->max_peripherals = 5;
asc->segments = aspeed_2400_fmc_segments;
+ asc->resets = aspeed_2400_fmc_resets;
asc->flash_window_base = 0x20000000;
asc->flash_window_size = 0x10000000;
asc->features = ASPEED_SMC_FEATURE_DMA;
@@ -1424,6 +1413,11 @@ static const TypeInfo aspeed_2400_spi1_info = {
.class_init = aspeed_2400_spi1_class_init,
};
+static const uint32_t aspeed_2500_fmc_resets[ASPEED_SMC_R_MAX] = {
+ [R_CONF] = (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0 |
+ CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE1),
+};
+
static const AspeedSegments aspeed_2500_fmc_segments[] = {
{ 0x20000000, 128 * MiB }, /* start address is readonly */
{ 0x28000000, 32 * MiB },
@@ -1444,6 +1438,7 @@ static void aspeed_2500_fmc_class_init(ObjectClass *klass, void *data)
asc->conf_enable_w0 = CONF_ENABLE_W0;
asc->max_peripherals = 3;
asc->segments = aspeed_2500_fmc_segments;
+ asc->resets = aspeed_2500_fmc_resets;
asc->flash_window_base = 0x20000000;
asc->flash_window_size = 0x10000000;
asc->features = ASPEED_SMC_FEATURE_DMA;
@@ -1569,6 +1564,12 @@ static void aspeed_2600_smc_reg_to_segment(const AspeedSMCState *s,
}
}
+static const uint32_t aspeed_2600_fmc_resets[ASPEED_SMC_R_MAX] = {
+ [R_CONF] = (CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE0 |
+ CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE1 |
+ CONF_FLASH_TYPE_SPI << CONF_FLASH_TYPE2),
+};
+
static const AspeedSegments aspeed_2600_fmc_segments[] = {
{ 0x0, 128 * MiB }, /* start address is readonly */
{ 128 * MiB, 128 * MiB }, /* default is disabled but needed for -kernel */
@@ -1589,6 +1590,7 @@ static void aspeed_2600_fmc_class_init(ObjectClass *klass, void *data)
asc->conf_enable_w0 = CONF_ENABLE_W0;
asc->max_peripherals = 3;
asc->segments = aspeed_2600_fmc_segments;
+ asc->resets = aspeed_2600_fmc_resets;
asc->flash_window_base = 0x20000000;
asc->flash_window_size = 0x10000000;
asc->features = ASPEED_SMC_FEATURE_DMA |
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 10/18] aspeed/smc: Introduce a new addr_width() class handler
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (8 preceding siblings ...)
2021-10-12 7:37 ` [PULL 09/18] aspeed/smc: Add default reset values Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 11/18] aspeed/smc: Remove unused attribute 'irqline' Cédric Le Goater
` (8 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Cédric Le Goater, qemu-arm, Joel Stanley,
qemu-devel
The AST2400 SPI controller has a transitional HW interface and it
stores the address width currently in use in a different register than
all the other SMC controllers. It needs special handling when working
in 4B mode.
Make it clear through a class handler. This also removes another use
of the segments array.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/ssi/aspeed_smc.h | 1 +
hw/ssi/aspeed_smc.c | 19 ++++++++++++-------
2 files changed, 13 insertions(+), 7 deletions(-)
diff --git a/include/hw/ssi/aspeed_smc.h b/include/hw/ssi/aspeed_smc.h
index a1ca0e65c405..8dc81294988e 100644
--- a/include/hw/ssi/aspeed_smc.h
+++ b/include/hw/ssi/aspeed_smc.h
@@ -111,6 +111,7 @@ struct AspeedSMCClass {
void (*reg_to_segment)(const AspeedSMCState *s, uint32_t reg,
AspeedSegments *seg);
void (*dma_ctrl)(AspeedSMCState *s, uint32_t value);
+ int (*addr_width)(const AspeedSMCState *s);
};
#endif /* ASPEED_SMC_H */
diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index 8cc7ccf45591..7129341c129e 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -196,7 +196,6 @@
* controller. These can be changed when board is initialized with the
* Segment Address Registers.
*/
-static const AspeedSegments aspeed_2400_spi1_segments[];
static const AspeedSegments aspeed_2500_spi1_segments[];
static const AspeedSegments aspeed_2500_spi2_segments[];
@@ -382,15 +381,15 @@ static inline int aspeed_smc_flash_cmd(const AspeedSMCFlash *fl)
return cmd;
}
-static inline int aspeed_smc_flash_is_4byte(const AspeedSMCFlash *fl)
+static inline int aspeed_smc_flash_addr_width(const AspeedSMCFlash *fl)
{
const AspeedSMCState *s = fl->controller;
AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
- if (asc->segments == aspeed_2400_spi1_segments) {
- return s->regs[s->r_ctrl0] & CTRL_AST2400_SPI_4BYTE;
+ if (asc->addr_width) {
+ return asc->addr_width(s);
} else {
- return s->regs[s->r_ce_ctrl] & (1 << (CTRL_EXTENDED0 + fl->cs));
+ return s->regs[s->r_ce_ctrl] & (1 << (CTRL_EXTENDED0 + fl->cs)) ? 4 : 3;
}
}
@@ -450,7 +449,7 @@ static void aspeed_smc_flash_setup(AspeedSMCFlash *fl, uint32_t addr)
{
const AspeedSMCState *s = fl->controller;
uint8_t cmd = aspeed_smc_flash_cmd(fl);
- int i = aspeed_smc_flash_is_4byte(fl) ? 4 : 3;
+ int i = aspeed_smc_flash_addr_width(fl);
/* Flash access can not exceed CS segment */
addr = aspeed_smc_check_segment_addr(fl, addr);
@@ -558,7 +557,7 @@ static bool aspeed_smc_do_snoop(AspeedSMCFlash *fl, uint64_t data,
unsigned size)
{
AspeedSMCState *s = fl->controller;
- uint8_t addr_width = aspeed_smc_flash_is_4byte(fl) ? 4 : 3;
+ uint8_t addr_width = aspeed_smc_flash_addr_width(fl);
trace_aspeed_smc_do_snoop(fl->cs, s->snoop_index, s->snoop_dummies,
(uint8_t) data & 0xff);
@@ -1384,6 +1383,11 @@ static const AspeedSegments aspeed_2400_spi1_segments[] = {
{ 0x30000000, 64 * MiB },
};
+static int aspeed_2400_spi1_addr_width(const AspeedSMCState *s)
+{
+ return s->regs[R_SPI_CTRL0] & CTRL_AST2400_SPI_4BYTE ? 4 : 3;
+}
+
static void aspeed_2400_spi1_class_init(ObjectClass *klass, void *data)
{
DeviceClass *dc = DEVICE_CLASS(klass);
@@ -1405,6 +1409,7 @@ static void aspeed_2400_spi1_class_init(ObjectClass *klass, void *data)
asc->segment_to_reg = aspeed_smc_segment_to_reg;
asc->reg_to_segment = aspeed_smc_reg_to_segment;
asc->dma_ctrl = aspeed_smc_dma_ctrl;
+ asc->addr_width = aspeed_2400_spi1_addr_width;
}
static const TypeInfo aspeed_2400_spi1_info = {
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 11/18] aspeed/smc: Remove unused attribute 'irqline'
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (9 preceding siblings ...)
2021-10-12 7:37 ` [PULL 10/18] aspeed/smc: Introduce a new addr_width() class handler Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 12/18] aspeed/i2c: QOMify AspeedI2CBus Cédric Le Goater
` (7 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Cédric Le Goater, qemu-arm, Joel Stanley,
qemu-devel
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/ssi/aspeed_smc.h | 1 -
1 file changed, 1 deletion(-)
diff --git a/include/hw/ssi/aspeed_smc.h b/include/hw/ssi/aspeed_smc.h
index 8dc81294988e..75bc793bd269 100644
--- a/include/hw/ssi/aspeed_smc.h
+++ b/include/hw/ssi/aspeed_smc.h
@@ -56,7 +56,6 @@ struct AspeedSMCState {
MemoryRegion mmio_flash_alias;
qemu_irq irq;
- int irqline;
uint32_t num_cs;
qemu_irq *cs_lines;
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 12/18] aspeed/i2c: QOMify AspeedI2CBus
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (10 preceding siblings ...)
2021-10-12 7:37 ` [PULL 11/18] aspeed/smc: Remove unused attribute 'irqline' Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 13/18] hw: aspeed_gpio: Fix pin I/O type declarations Cédric Le Goater
` (6 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Cédric Le Goater, qemu-arm, Joel Stanley,
qemu-devel
Introduce an AspeedI2CBus SysBusDevice model and attach the associated
memory region and IRQ to the newly instantiated objects.
Before this change, the I2C bus IRQs were all attached to the
SysBusDevice model of the I2C controller. Adapt the AST2600 SoC
realize routine to take into account this change.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/i2c/aspeed_i2c.h | 8 ++-
hw/arm/aspeed_ast2600.c | 7 +--
hw/i2c/aspeed_i2c.c | 101 +++++++++++++++++++++++++++++-------
3 files changed, 91 insertions(+), 25 deletions(-)
diff --git a/include/hw/i2c/aspeed_i2c.h b/include/hw/i2c/aspeed_i2c.h
index 565f83306624..4b9be09274c7 100644
--- a/include/hw/i2c/aspeed_i2c.h
+++ b/include/hw/i2c/aspeed_i2c.h
@@ -36,7 +36,11 @@ OBJECT_DECLARE_TYPE(AspeedI2CState, AspeedI2CClass, ASPEED_I2C)
struct AspeedI2CState;
-typedef struct AspeedI2CBus {
+#define TYPE_ASPEED_I2C_BUS "aspeed.i2c.bus"
+OBJECT_DECLARE_SIMPLE_TYPE(AspeedI2CBus, ASPEED_I2C_BUS)
+struct AspeedI2CBus {
+ SysBusDevice parent_obj;
+
struct AspeedI2CState *controller;
MemoryRegion mr;
@@ -54,7 +58,7 @@ typedef struct AspeedI2CBus {
uint32_t pool_ctrl;
uint32_t dma_addr;
uint32_t dma_len;
-} AspeedI2CBus;
+};
struct AspeedI2CState {
SysBusDevice parent_obj;
diff --git a/hw/arm/aspeed_ast2600.c b/hw/arm/aspeed_ast2600.c
index c69f27dff62a..a70e4c48a73c 100644
--- a/hw/arm/aspeed_ast2600.c
+++ b/hw/arm/aspeed_ast2600.c
@@ -337,11 +337,8 @@ static void aspeed_soc_ast2600_realize(DeviceState *dev, Error **errp)
for (i = 0; i < ASPEED_I2C_GET_CLASS(&s->i2c)->num_busses; i++) {
qemu_irq irq = qdev_get_gpio_in(DEVICE(&s->a7mpcore),
sc->irqmap[ASPEED_DEV_I2C] + i);
- /*
- * The AST2600 SoC has one IRQ per I2C bus. Skip the common
- * IRQ (AST2400 and AST2500) and connect all bussses.
- */
- sysbus_connect_irq(SYS_BUS_DEVICE(&s->i2c), i + 1, irq);
+ /* The AST2600 I2C controller has one IRQ per bus. */
+ sysbus_connect_irq(SYS_BUS_DEVICE(&s->i2c.busses[i]), 0, irq);
}
/* FMC, The number of CS is set at the board level */
diff --git a/hw/i2c/aspeed_i2c.c b/hw/i2c/aspeed_i2c.c
index 8d276d9ed391..03a4f5a91010 100644
--- a/hw/i2c/aspeed_i2c.c
+++ b/hw/i2c/aspeed_i2c.c
@@ -740,20 +740,20 @@ static const VMStateDescription aspeed_i2c_vmstate = {
static void aspeed_i2c_reset(DeviceState *dev)
{
- int i;
AspeedI2CState *s = ASPEED_I2C(dev);
- AspeedI2CClass *aic = ASPEED_I2C_GET_CLASS(s);
s->intr_status = 0;
+}
+
+static void aspeed_i2c_instance_init(Object *obj)
+{
+ AspeedI2CState *s = ASPEED_I2C(obj);
+ AspeedI2CClass *aic = ASPEED_I2C_GET_CLASS(s);
+ int i;
for (i = 0; i < aic->num_busses; i++) {
- s->busses[i].intr_ctrl = 0;
- s->busses[i].intr_status = 0;
- s->busses[i].cmd = 0;
- s->busses[i].buf = 0;
- s->busses[i].dma_addr = 0;
- s->busses[i].dma_len = 0;
- i2c_end_transfer(s->busses[i].bus);
+ object_initialize_child(obj, "bus[*]", &s->busses[i],
+ TYPE_ASPEED_I2C_BUS);
}
}
@@ -791,17 +791,21 @@ static void aspeed_i2c_realize(DeviceState *dev, Error **errp)
sysbus_init_mmio(sbd, &s->iomem);
for (i = 0; i < aic->num_busses; i++) {
- char name[32];
+ Object *bus = OBJECT(&s->busses[i]);
int offset = i < aic->gap ? 1 : 5;
- sysbus_init_irq(sbd, &s->busses[i].irq);
- snprintf(name, sizeof(name), "aspeed.i2c.%d", i);
- s->busses[i].controller = s;
- s->busses[i].id = i;
- s->busses[i].bus = i2c_init_bus(dev, name);
- memory_region_init_io(&s->busses[i].mr, OBJECT(dev),
- &aspeed_i2c_bus_ops, &s->busses[i], name,
- aic->reg_size);
+ if (!object_property_set_link(bus, "controller", OBJECT(s), errp)) {
+ return;
+ }
+
+ if (!object_property_set_uint(bus, "bus-id", i, errp)) {
+ return;
+ }
+
+ if (!sysbus_realize(SYS_BUS_DEVICE(bus), errp)) {
+ return;
+ }
+
memory_region_add_subregion(&s->iomem, aic->reg_size * (i + offset),
&s->busses[i].mr);
}
@@ -841,12 +845,72 @@ static void aspeed_i2c_class_init(ObjectClass *klass, void *data)
static const TypeInfo aspeed_i2c_info = {
.name = TYPE_ASPEED_I2C,
.parent = TYPE_SYS_BUS_DEVICE,
+ .instance_init = aspeed_i2c_instance_init,
.instance_size = sizeof(AspeedI2CState),
.class_init = aspeed_i2c_class_init,
.class_size = sizeof(AspeedI2CClass),
.abstract = true,
};
+static void aspeed_i2c_bus_reset(DeviceState *dev)
+{
+ AspeedI2CBus *s = ASPEED_I2C_BUS(dev);
+
+ s->intr_ctrl = 0;
+ s->intr_status = 0;
+ s->cmd = 0;
+ s->buf = 0;
+ s->dma_addr = 0;
+ s->dma_len = 0;
+ i2c_end_transfer(s->bus);
+}
+
+static void aspeed_i2c_bus_realize(DeviceState *dev, Error **errp)
+{
+ AspeedI2CBus *s = ASPEED_I2C_BUS(dev);
+ AspeedI2CClass *aic;
+ g_autofree char *name = g_strdup_printf(TYPE_ASPEED_I2C_BUS ".%d", s->id);
+
+ if (!s->controller) {
+ error_setg(errp, TYPE_ASPEED_I2C_BUS ": 'controller' link not set");
+ return;
+ }
+
+ aic = ASPEED_I2C_GET_CLASS(s->controller);
+
+ sysbus_init_irq(SYS_BUS_DEVICE(dev), &s->irq);
+
+ s->bus = i2c_init_bus(dev, name);
+
+ memory_region_init_io(&s->mr, OBJECT(s), &aspeed_i2c_bus_ops,
+ s, name, aic->reg_size);
+ sysbus_init_mmio(SYS_BUS_DEVICE(dev), &s->mr);
+}
+
+static Property aspeed_i2c_bus_properties[] = {
+ DEFINE_PROP_UINT8("bus-id", AspeedI2CBus, id, 0),
+ DEFINE_PROP_LINK("controller", AspeedI2CBus, controller, TYPE_ASPEED_I2C,
+ AspeedI2CState *),
+ DEFINE_PROP_END_OF_LIST(),
+};
+
+static void aspeed_i2c_bus_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+
+ dc->desc = "Aspeed I2C Bus";
+ dc->realize = aspeed_i2c_bus_realize;
+ dc->reset = aspeed_i2c_bus_reset;
+ device_class_set_props(dc, aspeed_i2c_bus_properties);
+}
+
+static const TypeInfo aspeed_i2c_bus_info = {
+ .name = TYPE_ASPEED_I2C_BUS,
+ .parent = TYPE_SYS_BUS_DEVICE,
+ .instance_size = sizeof(AspeedI2CBus),
+ .class_init = aspeed_i2c_bus_class_init,
+};
+
static qemu_irq aspeed_2400_i2c_bus_get_irq(AspeedI2CBus *bus)
{
return bus->controller->irq;
@@ -951,6 +1015,7 @@ static const TypeInfo aspeed_2600_i2c_info = {
static void aspeed_i2c_register_types(void)
{
+ type_register_static(&aspeed_i2c_bus_info);
type_register_static(&aspeed_i2c_info);
type_register_static(&aspeed_2400_i2c_info);
type_register_static(&aspeed_2500_i2c_info);
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 13/18] hw: aspeed_gpio: Fix pin I/O type declarations
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (11 preceding siblings ...)
2021-10-12 7:37 ` [PULL 12/18] aspeed/i2c: QOMify AspeedI2CBus Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 14/18] hw: aspeed_gpio: Fix GPIO array indexing Cédric Le Goater
` (5 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Damien Hedde, Andrew Jeffery, qemu-devel, qemu-arm, Joel Stanley,
Peter Delevoryas, Rashmica Gupta, Cédric Le Goater
From: Peter Delevoryas <pdel@fb.com>
Some of the pin declarations in the Aspeed GPIO module were incorrect,
probably because of confusion over which bits in the input and output
uint32_t's correspond to which groups in the label array. Since the
uint32_t literals are in big endian, it's sort of the opposite of what
would be intuitive. The least significant bit in ast2500_set_props[6]
corresponds to GPIOY0, not GPIOAB7.
GPIOxx indicates input and output capabilities, GPIxx indicates only
input, GPOxx indicates only output.
AST2500:
- Previously had GPIW0..GPIW7 and GPIX0..GPIX7, that's correct.
- Previously had GPIOY0..GPIOY3, should have been GPIOY0..GPIOY7.
- Previously had GPIOAB0..GPIOAB3 and GPIAB4..GPIAB7, should only have
been GPIOAB0..GPIOAB3.
AST2600:
- GPIOT0..GPIOT7 should have been GPIT0..GPIT7.
- GPIOU0..GPIOU7 should have been GPIU0..GPIU7.
- GPIW0..GPIW7 should have been GPIOW0..GPIOW7.
- GPIOY0..GPIOY7 and GPIOZ0...GPIOZ7 were disabled.
Fixes: 4b7f956862dc2db4c5c ("hw/gpio: Add basic Aspeed GPIO model for AST2400 and AST2500")
Fixes: 36d737ee82b2972167e ("hw/gpio: Add in AST2600 specific implementation")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Reviewed-by: Damien Hedde <damien.hedde@greensocs.com>
Reviewed-by: Rashmica Gupta <rashmica.g@gmail.com>
Message-Id: <20210928032456.3192603-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
hw/gpio/aspeed_gpio.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/hw/gpio/aspeed_gpio.c b/hw/gpio/aspeed_gpio.c
index dfa6d6cb40a9..33a40a624ac4 100644
--- a/hw/gpio/aspeed_gpio.c
+++ b/hw/gpio/aspeed_gpio.c
@@ -796,7 +796,7 @@ static const GPIOSetProperties ast2500_set_props[] = {
[3] = {0xffffffff, 0xffffffff, {"M", "N", "O", "P"} },
[4] = {0xffffffff, 0xffffffff, {"Q", "R", "S", "T"} },
[5] = {0xffffffff, 0x0000ffff, {"U", "V", "W", "X"} },
- [6] = {0xffffff0f, 0x0fffff0f, {"Y", "Z", "AA", "AB"} },
+ [6] = {0x0fffffff, 0x0fffffff, {"Y", "Z", "AA", "AB"} },
[7] = {0x000000ff, 0x000000ff, {"AC"} },
};
@@ -805,9 +805,9 @@ static GPIOSetProperties ast2600_3_3v_set_props[] = {
[1] = {0xffffffff, 0xffffffff, {"E", "F", "G", "H"} },
[2] = {0xffffffff, 0xffffffff, {"I", "J", "K", "L"} },
[3] = {0xffffffff, 0xffffffff, {"M", "N", "O", "P"} },
- [4] = {0xffffffff, 0xffffffff, {"Q", "R", "S", "T"} },
- [5] = {0xffffffff, 0x0000ffff, {"U", "V", "W", "X"} },
- [6] = {0xffff0000, 0x0fff0000, {"Y", "Z", "", ""} },
+ [4] = {0xffffffff, 0x00ffffff, {"Q", "R", "S", "T"} },
+ [5] = {0xffffffff, 0xffffff00, {"U", "V", "W", "X"} },
+ [6] = {0x0000ffff, 0x0000ffff, {"Y", "Z"} },
};
static GPIOSetProperties ast2600_1_8v_set_props[] = {
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 14/18] hw: aspeed_gpio: Fix GPIO array indexing
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (12 preceding siblings ...)
2021-10-12 7:37 ` [PULL 13/18] hw: aspeed_gpio: Fix pin I/O type declarations Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 15/18] hw/adc: Add basic Aspeed ADC model Cédric Le Goater
` (4 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, qemu-devel, qemu-arm, Cédric Le Goater,
Peter Delevoryas, Joel Stanley
From: Peter Delevoryas <pdel@fb.com>
The gpio array is declared as a dense array:
qemu_irq gpios[ASPEED_GPIO_NR_PINS];
(AST2500 has 228, AST2400 has 216, AST2600 has 208)
However, this array is used like a matrix of GPIO sets
(e.g. gpio[NR_SETS][NR_PINS_PER_SET] = gpio[8][32])
size_t offset = set * GPIOS_PER_SET + gpio;
qemu_set_irq(s->gpios[offset], !!(new & mask));
This can result in an out-of-bounds access to "s->gpios" because the
gpio sets do _not_ have the same length. Some of the groups (e.g.
GPIOAB) only have 4 pins. 228 != 8 * 32 == 256.
To fix this, I converted the gpio array from dense to sparse, to that
match both the hardware layout and this existing indexing code.
Fixes: 4b7f956862dc2db4c5c ("hw/gpio: Add basic Aspeed GPIO model for AST2400 and AST2500")
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20211008033501.934729-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/gpio/aspeed_gpio.h | 5 +--
hw/gpio/aspeed_gpio.c | 80 +++++++++++++++--------------------
2 files changed, 35 insertions(+), 50 deletions(-)
diff --git a/include/hw/gpio/aspeed_gpio.h b/include/hw/gpio/aspeed_gpio.h
index e1636ce7fea9..801846befb3b 100644
--- a/include/hw/gpio/aspeed_gpio.h
+++ b/include/hw/gpio/aspeed_gpio.h
@@ -17,9 +17,9 @@
OBJECT_DECLARE_TYPE(AspeedGPIOState, AspeedGPIOClass, ASPEED_GPIO)
#define ASPEED_GPIO_MAX_NR_SETS 8
+#define ASPEED_GPIOS_PER_SET 32
#define ASPEED_REGS_PER_BANK 14
#define ASPEED_GPIO_MAX_NR_REGS (ASPEED_REGS_PER_BANK * ASPEED_GPIO_MAX_NR_SETS)
-#define ASPEED_GPIO_NR_PINS 228
#define ASPEED_GROUPS_PER_SET 4
#define ASPEED_GPIO_NR_DEBOUNCE_REGS 3
#define ASPEED_CHARS_PER_GROUP_LABEL 4
@@ -60,7 +60,6 @@ struct AspeedGPIOClass {
const GPIOSetProperties *props;
uint32_t nr_gpio_pins;
uint32_t nr_gpio_sets;
- uint32_t gap;
const AspeedGPIOReg *reg_table;
};
@@ -72,7 +71,7 @@ struct AspeedGPIOState {
MemoryRegion iomem;
int pending;
qemu_irq irq;
- qemu_irq gpios[ASPEED_GPIO_NR_PINS];
+ qemu_irq gpios[ASPEED_GPIO_MAX_NR_SETS][ASPEED_GPIOS_PER_SET];
/* Parallel GPIO Registers */
uint32_t debounce_regs[ASPEED_GPIO_NR_DEBOUNCE_REGS];
diff --git a/hw/gpio/aspeed_gpio.c b/hw/gpio/aspeed_gpio.c
index 33a40a624ac4..911d21c8cfbe 100644
--- a/hw/gpio/aspeed_gpio.c
+++ b/hw/gpio/aspeed_gpio.c
@@ -16,11 +16,7 @@
#include "hw/irq.h"
#include "migration/vmstate.h"
-#define GPIOS_PER_REG 32
-#define GPIOS_PER_SET GPIOS_PER_REG
-#define GPIO_PIN_GAP_SIZE 4
#define GPIOS_PER_GROUP 8
-#define GPIO_GROUP_SHIFT 3
/* GPIO Source Types */
#define ASPEED_CMD_SRC_MASK 0x01010101
@@ -259,7 +255,7 @@ static void aspeed_gpio_update(AspeedGPIOState *s, GPIOSets *regs,
diff = old ^ new;
if (diff) {
- for (gpio = 0; gpio < GPIOS_PER_REG; gpio++) {
+ for (gpio = 0; gpio < ASPEED_GPIOS_PER_SET; gpio++) {
uint32_t mask = 1 << gpio;
/* If the gpio needs to be updated... */
@@ -283,8 +279,7 @@ static void aspeed_gpio_update(AspeedGPIOState *s, GPIOSets *regs,
if (direction & mask) {
/* ...trigger the line-state IRQ */
ptrdiff_t set = aspeed_gpio_set_idx(s, regs);
- size_t offset = set * GPIOS_PER_SET + gpio;
- qemu_set_irq(s->gpios[offset], !!(new & mask));
+ qemu_set_irq(s->gpios[set][gpio], !!(new & mask));
} else {
/* ...otherwise if we meet the line's current IRQ policy... */
if (aspeed_evaluate_irq(regs, old & mask, gpio)) {
@@ -297,21 +292,6 @@ static void aspeed_gpio_update(AspeedGPIOState *s, GPIOSets *regs,
qemu_set_irq(s->irq, !!(s->pending));
}
-static uint32_t aspeed_adjust_pin(AspeedGPIOState *s, uint32_t pin)
-{
- AspeedGPIOClass *agc = ASPEED_GPIO_GET_CLASS(s);
- /*
- * The 2500 has a 4 pin gap in group AB and the 2400 has a 4 pin
- * gap in group Y (and only four pins in AB but this is the last group so
- * it doesn't matter).
- */
- if (agc->gap && pin >= agc->gap) {
- pin += GPIO_PIN_GAP_SIZE;
- }
-
- return pin;
-}
-
static bool aspeed_gpio_get_pin_level(AspeedGPIOState *s, uint32_t set_idx,
uint32_t pin)
{
@@ -367,7 +347,7 @@ static uint32_t update_value_control_source(GPIOSets *regs, uint32_t old_value,
uint32_t new_value = 0;
/* for each group in set */
- for (i = 0; i < GPIOS_PER_REG; i += GPIOS_PER_GROUP) {
+ for (i = 0; i < ASPEED_GPIOS_PER_SET; i += GPIOS_PER_GROUP) {
cmd_source = extract32(regs->cmd_source_0, i, 1)
| (extract32(regs->cmd_source_1, i, 1) << 1);
@@ -637,7 +617,7 @@ static void aspeed_gpio_write(void *opaque, hwaddr offset, uint64_t data,
* bidirectional | 1 | 1 | data
* input only | 1 | 0 | 0
* output only | 0 | 1 | 1
- * no pin / gap | 0 | 0 | 0
+ * no pin | 0 | 0 | 0
*
* which is captured by:
* data = ( data | ~input) & output;
@@ -779,7 +759,7 @@ static void aspeed_gpio_set_pin(Object *obj, Visitor *v, const char *name,
}
/****************** Setup functions ******************/
-static const GPIOSetProperties ast2400_set_props[] = {
+static const GPIOSetProperties ast2400_set_props[ASPEED_GPIO_MAX_NR_SETS] = {
[0] = {0xffffffff, 0xffffffff, {"A", "B", "C", "D"} },
[1] = {0xffffffff, 0xffffffff, {"E", "F", "G", "H"} },
[2] = {0xffffffff, 0xffffffff, {"I", "J", "K", "L"} },
@@ -789,7 +769,7 @@ static const GPIOSetProperties ast2400_set_props[] = {
[6] = {0x0000000f, 0x0fffff0f, {"Y", "Z", "AA", "AB"} },
};
-static const GPIOSetProperties ast2500_set_props[] = {
+static const GPIOSetProperties ast2500_set_props[ASPEED_GPIO_MAX_NR_SETS] = {
[0] = {0xffffffff, 0xffffffff, {"A", "B", "C", "D"} },
[1] = {0xffffffff, 0xffffffff, {"E", "F", "G", "H"} },
[2] = {0xffffffff, 0xffffffff, {"I", "J", "K", "L"} },
@@ -800,7 +780,7 @@ static const GPIOSetProperties ast2500_set_props[] = {
[7] = {0x000000ff, 0x000000ff, {"AC"} },
};
-static GPIOSetProperties ast2600_3_3v_set_props[] = {
+static GPIOSetProperties ast2600_3_3v_set_props[ASPEED_GPIO_MAX_NR_SETS] = {
[0] = {0xffffffff, 0xffffffff, {"A", "B", "C", "D"} },
[1] = {0xffffffff, 0xffffffff, {"E", "F", "G", "H"} },
[2] = {0xffffffff, 0xffffffff, {"I", "J", "K", "L"} },
@@ -810,7 +790,7 @@ static GPIOSetProperties ast2600_3_3v_set_props[] = {
[6] = {0x0000ffff, 0x0000ffff, {"Y", "Z"} },
};
-static GPIOSetProperties ast2600_1_8v_set_props[] = {
+static GPIOSetProperties ast2600_1_8v_set_props[ASPEED_GPIO_MAX_NR_SETS] = {
[0] = {0xffffffff, 0xffffffff, {"18A", "18B", "18C", "18D"} },
[1] = {0x0000000f, 0x0000000f, {"18E"} },
};
@@ -836,14 +816,20 @@ static void aspeed_gpio_realize(DeviceState *dev, Error **errp)
AspeedGPIOState *s = ASPEED_GPIO(dev);
SysBusDevice *sbd = SYS_BUS_DEVICE(dev);
AspeedGPIOClass *agc = ASPEED_GPIO_GET_CLASS(s);
- int pin;
/* Interrupt parent line */
sysbus_init_irq(sbd, &s->irq);
/* Individual GPIOs */
- for (pin = 0; pin < agc->nr_gpio_pins; pin++) {
- sysbus_init_irq(sbd, &s->gpios[pin]);
+ for (int i = 0; i < ASPEED_GPIO_MAX_NR_SETS; i++) {
+ const GPIOSetProperties *props = &agc->props[i];
+ uint32_t skip = ~(props->input | props->output);
+ for (int j = 0; j < ASPEED_GPIOS_PER_SET; j++) {
+ if (skip >> j & 1) {
+ continue;
+ }
+ sysbus_init_irq(sbd, &s->gpios[i][j]);
+ }
}
memory_region_init_io(&s->iomem, OBJECT(s), &aspeed_gpio_ops, s,
@@ -856,20 +842,22 @@ static void aspeed_gpio_init(Object *obj)
{
AspeedGPIOState *s = ASPEED_GPIO(obj);
AspeedGPIOClass *agc = ASPEED_GPIO_GET_CLASS(s);
- int pin;
-
- for (pin = 0; pin < agc->nr_gpio_pins; pin++) {
- char *name;
- int set_idx = pin / GPIOS_PER_SET;
- int pin_idx = aspeed_adjust_pin(s, pin) - (set_idx * GPIOS_PER_SET);
- int group_idx = pin_idx >> GPIO_GROUP_SHIFT;
- const GPIOSetProperties *props = &agc->props[set_idx];
-
- name = g_strdup_printf("gpio%s%d", props->group_label[group_idx],
- pin_idx % GPIOS_PER_GROUP);
- object_property_add(obj, name, "bool", aspeed_gpio_get_pin,
- aspeed_gpio_set_pin, NULL, NULL);
- g_free(name);
+
+ for (int i = 0; i < ASPEED_GPIO_MAX_NR_SETS; i++) {
+ const GPIOSetProperties *props = &agc->props[i];
+ uint32_t skip = ~(props->input | props->output);
+ for (int j = 0; j < ASPEED_GPIOS_PER_SET; j++) {
+ if (skip >> j & 1) {
+ continue;
+ }
+ int group_idx = j / GPIOS_PER_GROUP;
+ int pin_idx = j % GPIOS_PER_GROUP;
+ const char *group = &props->group_label[group_idx][0];
+ char *name = g_strdup_printf("gpio%s%d", group, pin_idx);
+ object_property_add(obj, name, "bool", aspeed_gpio_get_pin,
+ aspeed_gpio_set_pin, NULL, NULL);
+ g_free(name);
+ }
}
}
@@ -926,7 +914,6 @@ static void aspeed_gpio_ast2400_class_init(ObjectClass *klass, void *data)
agc->props = ast2400_set_props;
agc->nr_gpio_pins = 216;
agc->nr_gpio_sets = 7;
- agc->gap = 196;
agc->reg_table = aspeed_3_3v_gpios;
}
@@ -937,7 +924,6 @@ static void aspeed_gpio_2500_class_init(ObjectClass *klass, void *data)
agc->props = ast2500_set_props;
agc->nr_gpio_pins = 228;
agc->nr_gpio_sets = 8;
- agc->gap = 220;
agc->reg_table = aspeed_3_3v_gpios;
}
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 15/18] hw/adc: Add basic Aspeed ADC model
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (13 preceding siblings ...)
2021-10-12 7:37 ` [PULL 14/18] hw: aspeed_gpio: Fix GPIO array indexing Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 16/18] hw/arm: Integrate ADC model into Aspeed SoC Cédric Le Goater
` (3 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, qemu-devel, qemu-arm, Cédric Le Goater,
Peter Delevoryas, Joel Stanley
From: Andrew Jeffery <andrew@aj.id.au>
This model implements enough behaviour to do basic functionality tests
such as device initialisation and read out of dummy sample values. The
sample value generation strategy is similar to the STM ADC already in
the tree.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
[clg : support for multiple engines (AST2600) ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[pdel : refactored engine register struct fields to regs[] array field]
[pdel : added guest-error checking for upper-8 channel regs in AST2600]
[pdel : allow 16-bit reads of the channel data registers]
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20211005052604.1674891-2-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/adc/aspeed_adc.h | 55 +++++
hw/adc/aspeed_adc.c | 427 ++++++++++++++++++++++++++++++++++++
hw/adc/meson.build | 1 +
hw/adc/trace-events | 3 +
4 files changed, 486 insertions(+)
create mode 100644 include/hw/adc/aspeed_adc.h
create mode 100644 hw/adc/aspeed_adc.c
diff --git a/include/hw/adc/aspeed_adc.h b/include/hw/adc/aspeed_adc.h
new file mode 100644
index 000000000000..2f166e8be111
--- /dev/null
+++ b/include/hw/adc/aspeed_adc.h
@@ -0,0 +1,55 @@
+/*
+ * Aspeed ADC
+ *
+ * Copyright 2017-2021 IBM Corp.
+ *
+ * Andrew Jeffery <andrew@aj.id.au>
+ *
+ * SPDX-License-Identifier: GPL-2.0-or-later
+ */
+
+#ifndef HW_ADC_ASPEED_ADC_H
+#define HW_ADC_ASPEED_ADC_H
+
+#include "hw/sysbus.h"
+
+#define TYPE_ASPEED_ADC "aspeed.adc"
+#define TYPE_ASPEED_2400_ADC TYPE_ASPEED_ADC "-ast2400"
+#define TYPE_ASPEED_2500_ADC TYPE_ASPEED_ADC "-ast2500"
+#define TYPE_ASPEED_2600_ADC TYPE_ASPEED_ADC "-ast2600"
+OBJECT_DECLARE_TYPE(AspeedADCState, AspeedADCClass, ASPEED_ADC)
+
+#define TYPE_ASPEED_ADC_ENGINE "aspeed.adc.engine"
+OBJECT_DECLARE_SIMPLE_TYPE(AspeedADCEngineState, ASPEED_ADC_ENGINE)
+
+#define ASPEED_ADC_NR_CHANNELS 16
+#define ASPEED_ADC_NR_REGS (0xD0 >> 2)
+
+struct AspeedADCEngineState {
+ /* <private> */
+ SysBusDevice parent;
+
+ MemoryRegion mmio;
+ qemu_irq irq;
+ uint32_t engine_id;
+ uint32_t nr_channels;
+ uint32_t regs[ASPEED_ADC_NR_REGS];
+};
+
+struct AspeedADCState {
+ /* <private> */
+ SysBusDevice parent;
+
+ MemoryRegion mmio;
+ qemu_irq irq;
+
+ AspeedADCEngineState engines[2];
+};
+
+struct AspeedADCClass {
+ SysBusDeviceClass parent_class;
+
+ uint32_t nr_engines;
+};
+
+#endif /* HW_ADC_ASPEED_ADC_H */
diff --git a/hw/adc/aspeed_adc.c b/hw/adc/aspeed_adc.c
new file mode 100644
index 000000000000..c5fcae29f635
--- /dev/null
+++ b/hw/adc/aspeed_adc.c
@@ -0,0 +1,427 @@
+/*
+ * Aspeed ADC
+ *
+ * Copyright 2017-2021 IBM Corp.
+ *
+ * Andrew Jeffery <andrew@aj.id.au>
+ *
+ * SPDX-License-Identifier: GPL-2.0-or-later
+ */
+
+#include "qemu/osdep.h"
+#include "qapi/error.h"
+#include "qemu/log.h"
+#include "hw/irq.h"
+#include "hw/qdev-properties.h"
+#include "migration/vmstate.h"
+#include "hw/adc/aspeed_adc.h"
+#include "trace.h"
+
+#define ASPEED_ADC_MEMORY_REGION_SIZE 0x1000
+#define ASPEED_ADC_ENGINE_MEMORY_REGION_SIZE 0x100
+#define ASPEED_ADC_ENGINE_CH_EN_MASK 0xffff0000
+#define ASPEED_ADC_ENGINE_CH_EN(x) ((BIT(x)) << 16)
+#define ASPEED_ADC_ENGINE_INIT BIT(8)
+#define ASPEED_ADC_ENGINE_AUTO_COMP BIT(5)
+#define ASPEED_ADC_ENGINE_COMP BIT(4)
+#define ASPEED_ADC_ENGINE_MODE_MASK 0x0000000e
+#define ASPEED_ADC_ENGINE_MODE_OFF (0b000 << 1)
+#define ASPEED_ADC_ENGINE_MODE_STANDBY (0b001 << 1)
+#define ASPEED_ADC_ENGINE_MODE_NORMAL (0b111 << 1)
+#define ASPEED_ADC_ENGINE_EN BIT(0)
+#define ASPEED_ADC_HYST_EN BIT(31)
+
+#define ASPEED_ADC_L_MASK ((1 << 10) - 1)
+#define ASPEED_ADC_L(x) ((x) & ASPEED_ADC_L_MASK)
+#define ASPEED_ADC_H(x) (((x) >> 16) & ASPEED_ADC_L_MASK)
+#define ASPEED_ADC_LH_MASK (ASPEED_ADC_L_MASK << 16 | ASPEED_ADC_L_MASK)
+#define LOWER_CHANNEL_MASK ((1 << 10) - 1)
+#define LOWER_CHANNEL_DATA(x) ((x) & LOWER_CHANNEL_MASK)
+#define UPPER_CHANNEL_DATA(x) (((x) >> 16) & LOWER_CHANNEL_MASK)
+
+#define TO_REG(addr) (addr >> 2)
+
+#define ENGINE_CONTROL TO_REG(0x00)
+#define INTERRUPT_CONTROL TO_REG(0x04)
+#define VGA_DETECT_CONTROL TO_REG(0x08)
+#define CLOCK_CONTROL TO_REG(0x0C)
+#define DATA_CHANNEL_1_AND_0 TO_REG(0x10)
+#define DATA_CHANNEL_7_AND_6 TO_REG(0x1C)
+#define DATA_CHANNEL_9_AND_8 TO_REG(0x20)
+#define DATA_CHANNEL_15_AND_14 TO_REG(0x2C)
+#define BOUNDS_CHANNEL_0 TO_REG(0x30)
+#define BOUNDS_CHANNEL_7 TO_REG(0x4C)
+#define BOUNDS_CHANNEL_8 TO_REG(0x50)
+#define BOUNDS_CHANNEL_15 TO_REG(0x6C)
+#define HYSTERESIS_CHANNEL_0 TO_REG(0x70)
+#define HYSTERESIS_CHANNEL_7 TO_REG(0x8C)
+#define HYSTERESIS_CHANNEL_8 TO_REG(0x90)
+#define HYSTERESIS_CHANNEL_15 TO_REG(0xAC)
+#define INTERRUPT_SOURCE TO_REG(0xC0)
+#define COMPENSATING_AND_TRIMMING TO_REG(0xC4)
+
+static inline uint32_t update_channels(uint32_t current)
+{
+ return ((((current >> 16) & ASPEED_ADC_L_MASK) + 7) << 16) |
+ ((current + 5) & ASPEED_ADC_L_MASK);
+}
+
+static bool breaks_threshold(AspeedADCEngineState *s, int reg)
+{
+ assert(reg >= DATA_CHANNEL_1_AND_0 &&
+ reg < DATA_CHANNEL_1_AND_0 + s->nr_channels / 2);
+
+ int a_bounds_reg = BOUNDS_CHANNEL_0 + (reg - DATA_CHANNEL_1_AND_0) * 2;
+ int b_bounds_reg = a_bounds_reg + 1;
+ uint32_t a_and_b = s->regs[reg];
+ uint32_t a_bounds = s->regs[a_bounds_reg];
+ uint32_t b_bounds = s->regs[b_bounds_reg];
+ uint32_t a = ASPEED_ADC_L(a_and_b);
+ uint32_t b = ASPEED_ADC_H(a_and_b);
+ uint32_t a_lower = ASPEED_ADC_L(a_bounds);
+ uint32_t a_upper = ASPEED_ADC_H(a_bounds);
+ uint32_t b_lower = ASPEED_ADC_L(b_bounds);
+ uint32_t b_upper = ASPEED_ADC_H(b_bounds);
+
+ return (a < a_lower || a > a_upper) ||
+ (b < b_lower || b > b_upper);
+}
+
+static uint32_t read_channel_sample(AspeedADCEngineState *s, int reg)
+{
+ assert(reg >= DATA_CHANNEL_1_AND_0 &&
+ reg < DATA_CHANNEL_1_AND_0 + s->nr_channels / 2);
+
+ /* Poor man's sampling */
+ uint32_t value = s->regs[reg];
+ s->regs[reg] = update_channels(s->regs[reg]);
+
+ if (breaks_threshold(s, reg)) {
+ s->regs[INTERRUPT_CONTROL] |= BIT(reg - DATA_CHANNEL_1_AND_0);
+ qemu_irq_raise(s->irq);
+ }
+
+ return value;
+}
+
+static uint64_t aspeed_adc_engine_read(void *opaque, hwaddr addr,
+ unsigned int size)
+{
+ AspeedADCEngineState *s = ASPEED_ADC_ENGINE(opaque);
+ int reg = TO_REG(addr);
+ uint32_t value = 0;
+
+ switch (reg) {
+ case BOUNDS_CHANNEL_8 ... BOUNDS_CHANNEL_15:
+ if (s->nr_channels <= 8) {
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: engine[%u]: "
+ "bounds register %u invalid, only 0...7 valid\n",
+ __func__, s->engine_id, reg - BOUNDS_CHANNEL_0);
+ break;
+ }
+ /* fallthrough */
+ case HYSTERESIS_CHANNEL_8 ... HYSTERESIS_CHANNEL_15:
+ if (s->nr_channels <= 8) {
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: engine[%u]: "
+ "hysteresis register %u invalid, only 0...7 valid\n",
+ __func__, s->engine_id, reg - HYSTERESIS_CHANNEL_0);
+ break;
+ }
+ /* fallthrough */
+ case BOUNDS_CHANNEL_0 ... BOUNDS_CHANNEL_7:
+ case HYSTERESIS_CHANNEL_0 ... HYSTERESIS_CHANNEL_7:
+ case ENGINE_CONTROL:
+ case INTERRUPT_CONTROL:
+ case VGA_DETECT_CONTROL:
+ case CLOCK_CONTROL:
+ case INTERRUPT_SOURCE:
+ case COMPENSATING_AND_TRIMMING:
+ value = s->regs[reg];
+ break;
+ case DATA_CHANNEL_9_AND_8 ... DATA_CHANNEL_15_AND_14:
+ if (s->nr_channels <= 8) {
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: engine[%u]: "
+ "data register %u invalid, only 0...3 valid\n",
+ __func__, s->engine_id, reg - DATA_CHANNEL_1_AND_0);
+ break;
+ }
+ /* fallthrough */
+ case DATA_CHANNEL_1_AND_0 ... DATA_CHANNEL_7_AND_6:
+ value = read_channel_sample(s, reg);
+ /* Allow 16-bit reads of the data registers */
+ if (addr & 0x2) {
+ assert(size == 2);
+ value >>= 16;
+ }
+ break;
+ default:
+ qemu_log_mask(LOG_UNIMP, "%s: engine[%u]: 0x%" HWADDR_PRIx "\n",
+ __func__, s->engine_id, addr);
+ break;
+ }
+
+ trace_aspeed_adc_engine_read(s->engine_id, addr, value);
+ return value;
+}
+
+static void aspeed_adc_engine_write(void *opaque, hwaddr addr, uint64_t value,
+ unsigned int size)
+{
+ AspeedADCEngineState *s = ASPEED_ADC_ENGINE(opaque);
+ int reg = TO_REG(addr);
+ uint32_t init = 0;
+
+ trace_aspeed_adc_engine_write(s->engine_id, addr, value);
+
+ switch (reg) {
+ case ENGINE_CONTROL:
+ init = !!(value & ASPEED_ADC_ENGINE_EN);
+ init *= ASPEED_ADC_ENGINE_INIT;
+
+ value &= ~ASPEED_ADC_ENGINE_INIT;
+ value |= init;
+
+ value &= ~ASPEED_ADC_ENGINE_AUTO_COMP;
+ break;
+ case INTERRUPT_CONTROL:
+ case VGA_DETECT_CONTROL:
+ case CLOCK_CONTROL:
+ break;
+ case DATA_CHANNEL_9_AND_8 ... DATA_CHANNEL_15_AND_14:
+ if (s->nr_channels <= 8) {
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: engine[%u]: "
+ "data register %u invalid, only 0...3 valid\n",
+ __func__, s->engine_id, reg - DATA_CHANNEL_1_AND_0);
+ return;
+ }
+ /* fallthrough */
+ case BOUNDS_CHANNEL_8 ... BOUNDS_CHANNEL_15:
+ if (s->nr_channels <= 8) {
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: engine[%u]: "
+ "bounds register %u invalid, only 0...7 valid\n",
+ __func__, s->engine_id, reg - BOUNDS_CHANNEL_0);
+ return;
+ }
+ /* fallthrough */
+ case DATA_CHANNEL_1_AND_0 ... DATA_CHANNEL_7_AND_6:
+ case BOUNDS_CHANNEL_0 ... BOUNDS_CHANNEL_7:
+ value &= ASPEED_ADC_LH_MASK;
+ break;
+ case HYSTERESIS_CHANNEL_8 ... HYSTERESIS_CHANNEL_15:
+ if (s->nr_channels <= 8) {
+ qemu_log_mask(LOG_GUEST_ERROR, "%s: engine[%u]: "
+ "hysteresis register %u invalid, only 0...7 valid\n",
+ __func__, s->engine_id, reg - HYSTERESIS_CHANNEL_0);
+ return;
+ }
+ /* fallthrough */
+ case HYSTERESIS_CHANNEL_0 ... HYSTERESIS_CHANNEL_7:
+ value &= (ASPEED_ADC_HYST_EN | ASPEED_ADC_LH_MASK);
+ break;
+ case INTERRUPT_SOURCE:
+ value &= 0xffff;
+ break;
+ case COMPENSATING_AND_TRIMMING:
+ value &= 0xf;
+ break;
+ default:
+ qemu_log_mask(LOG_UNIMP, "%s: engine[%u]: "
+ "0x%" HWADDR_PRIx " 0x%" PRIx64 "\n",
+ __func__, s->engine_id, addr, value);
+ break;
+ }
+
+ s->regs[reg] = value;
+}
+
+static const MemoryRegionOps aspeed_adc_engine_ops = {
+ .read = aspeed_adc_engine_read,
+ .write = aspeed_adc_engine_write,
+ .endianness = DEVICE_LITTLE_ENDIAN,
+ .valid = {
+ .min_access_size = 2,
+ .max_access_size = 4,
+ .unaligned = false,
+ },
+};
+
+static const uint32_t aspeed_adc_resets[ASPEED_ADC_NR_REGS] = {
+ [ENGINE_CONTROL] = 0x00000000,
+ [INTERRUPT_CONTROL] = 0x00000000,
+ [VGA_DETECT_CONTROL] = 0x0000000f,
+ [CLOCK_CONTROL] = 0x0000000f,
+};
+
+static void aspeed_adc_engine_reset(DeviceState *dev)
+{
+ AspeedADCEngineState *s = ASPEED_ADC_ENGINE(dev);
+
+ memcpy(s->regs, aspeed_adc_resets, sizeof(aspeed_adc_resets));
+}
+
+static void aspeed_adc_engine_realize(DeviceState *dev, Error **errp)
+{
+ AspeedADCEngineState *s = ASPEED_ADC_ENGINE(dev);
+ SysBusDevice *sbd = SYS_BUS_DEVICE(dev);
+ g_autofree char *name = g_strdup_printf(TYPE_ASPEED_ADC_ENGINE ".%d",
+ s->engine_id);
+
+ assert(s->engine_id < 2);
+
+ sysbus_init_irq(sbd, &s->irq);
+
+ memory_region_init_io(&s->mmio, OBJECT(s), &aspeed_adc_engine_ops, s, name,
+ ASPEED_ADC_ENGINE_MEMORY_REGION_SIZE);
+
+ sysbus_init_mmio(sbd, &s->mmio);
+}
+
+static const VMStateDescription vmstate_aspeed_adc_engine = {
+ .name = TYPE_ASPEED_ADC,
+ .version_id = 1,
+ .minimum_version_id = 1,
+ .fields = (VMStateField[]) {
+ VMSTATE_UINT32_ARRAY(regs, AspeedADCEngineState, ASPEED_ADC_NR_REGS),
+ VMSTATE_END_OF_LIST(),
+ }
+};
+
+static Property aspeed_adc_engine_properties[] = {
+ DEFINE_PROP_UINT32("engine-id", AspeedADCEngineState, engine_id, 0),
+ DEFINE_PROP_UINT32("nr-channels", AspeedADCEngineState, nr_channels, 0),
+ DEFINE_PROP_END_OF_LIST(),
+};
+
+static void aspeed_adc_engine_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+
+ dc->realize = aspeed_adc_engine_realize;
+ dc->reset = aspeed_adc_engine_reset;
+ device_class_set_props(dc, aspeed_adc_engine_properties);
+ dc->desc = "Aspeed Analog-to-Digital Engine";
+ dc->vmsd = &vmstate_aspeed_adc_engine;
+}
+
+static const TypeInfo aspeed_adc_engine_info = {
+ .name = TYPE_ASPEED_ADC_ENGINE,
+ .parent = TYPE_SYS_BUS_DEVICE,
+ .instance_size = sizeof(AspeedADCEngineState),
+ .class_init = aspeed_adc_engine_class_init,
+};
+
+static void aspeed_adc_instance_init(Object *obj)
+{
+ AspeedADCState *s = ASPEED_ADC(obj);
+ AspeedADCClass *aac = ASPEED_ADC_GET_CLASS(obj);
+ uint32_t nr_channels = ASPEED_ADC_NR_CHANNELS / aac->nr_engines;
+
+ for (int i = 0; i < aac->nr_engines; i++) {
+ AspeedADCEngineState *engine = &s->engines[i];
+ object_initialize_child(obj, "engine[*]", engine,
+ TYPE_ASPEED_ADC_ENGINE);
+ qdev_prop_set_uint32(DEVICE(engine), "engine-id", i);
+ qdev_prop_set_uint32(DEVICE(engine), "nr-channels", nr_channels);
+ }
+}
+
+static void aspeed_adc_set_irq(void *opaque, int n, int level)
+{
+ AspeedADCState *s = opaque;
+ AspeedADCClass *aac = ASPEED_ADC_GET_CLASS(s);
+ uint32_t pending = 0;
+
+ /* TODO: update Global IRQ status register on AST2600 (Need specs) */
+ for (int i = 0; i < aac->nr_engines; i++) {
+ uint32_t irq_status = s->engines[i].regs[INTERRUPT_CONTROL] & 0xFF;
+ pending |= irq_status << (i * 8);
+ }
+
+ qemu_set_irq(s->irq, !!pending);
+}
+
+static void aspeed_adc_realize(DeviceState *dev, Error **errp)
+{
+ AspeedADCState *s = ASPEED_ADC(dev);
+ SysBusDevice *sbd = SYS_BUS_DEVICE(dev);
+ AspeedADCClass *aac = ASPEED_ADC_GET_CLASS(dev);
+
+ qdev_init_gpio_in_named_with_opaque(DEVICE(sbd), aspeed_adc_set_irq,
+ s, NULL, aac->nr_engines);
+
+ sysbus_init_irq(sbd, &s->irq);
+
+ memory_region_init(&s->mmio, OBJECT(s), TYPE_ASPEED_ADC,
+ ASPEED_ADC_MEMORY_REGION_SIZE);
+
+ sysbus_init_mmio(sbd, &s->mmio);
+
+ for (int i = 0; i < aac->nr_engines; i++) {
+ Object *eng = OBJECT(&s->engines[i]);
+
+ if (!sysbus_realize(SYS_BUS_DEVICE(eng), errp)) {
+ return;
+ }
+ sysbus_connect_irq(SYS_BUS_DEVICE(eng), 0,
+ qdev_get_gpio_in(DEVICE(sbd), i));
+ memory_region_add_subregion(&s->mmio,
+ i * ASPEED_ADC_ENGINE_MEMORY_REGION_SIZE,
+ &s->engines[i].mmio);
+ }
+}
+
+static void aspeed_adc_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedADCClass *aac = ASPEED_ADC_CLASS(klass);
+
+ dc->realize = aspeed_adc_realize;
+ dc->desc = "Aspeed Analog-to-Digital Converter";
+ aac->nr_engines = 1;
+}
+
+static void aspeed_2600_adc_class_init(ObjectClass *klass, void *data)
+{
+ DeviceClass *dc = DEVICE_CLASS(klass);
+ AspeedADCClass *aac = ASPEED_ADC_CLASS(klass);
+
+ dc->desc = "ASPEED 2600 ADC Controller";
+ aac->nr_engines = 2;
+}
+
+static const TypeInfo aspeed_adc_info = {
+ .name = TYPE_ASPEED_ADC,
+ .parent = TYPE_SYS_BUS_DEVICE,
+ .instance_init = aspeed_adc_instance_init,
+ .instance_size = sizeof(AspeedADCState),
+ .class_init = aspeed_adc_class_init,
+ .class_size = sizeof(AspeedADCClass),
+ .abstract = true,
+};
+
+static const TypeInfo aspeed_2400_adc_info = {
+ .name = TYPE_ASPEED_2400_ADC,
+ .parent = TYPE_ASPEED_ADC,
+};
+
+static const TypeInfo aspeed_2500_adc_info = {
+ .name = TYPE_ASPEED_2500_ADC,
+ .parent = TYPE_ASPEED_ADC,
+};
+
+static const TypeInfo aspeed_2600_adc_info = {
+ .name = TYPE_ASPEED_2600_ADC,
+ .parent = TYPE_ASPEED_ADC,
+ .class_init = aspeed_2600_adc_class_init,
+};
+
+static void aspeed_adc_register_types(void)
+{
+ type_register_static(&aspeed_adc_engine_info);
+ type_register_static(&aspeed_adc_info);
+ type_register_static(&aspeed_2400_adc_info);
+ type_register_static(&aspeed_2500_adc_info);
+ type_register_static(&aspeed_2600_adc_info);
+}
+
+type_init(aspeed_adc_register_types);
diff --git a/hw/adc/meson.build b/hw/adc/meson.build
index ac4f093fea7c..b29ac7ccdf53 100644
--- a/hw/adc/meson.build
+++ b/hw/adc/meson.build
@@ -1,4 +1,5 @@
softmmu_ss.add(when: 'CONFIG_STM32F2XX_ADC', if_true: files('stm32f2xx_adc.c'))
+softmmu_ss.add(when: 'CONFIG_ASPEED_SOC', if_true: files('aspeed_adc.c'))
softmmu_ss.add(when: 'CONFIG_NPCM7XX', if_true: files('npcm7xx_adc.c'))
softmmu_ss.add(when: 'CONFIG_ZYNQ', if_true: files('zynq-xadc.c'))
softmmu_ss.add(when: 'CONFIG_MAX111X', if_true: files('max111x.c'))
diff --git a/hw/adc/trace-events b/hw/adc/trace-events
index 456f21c8f438..5a4c444d773a 100644
--- a/hw/adc/trace-events
+++ b/hw/adc/trace-events
@@ -3,3 +3,6 @@
# npcm7xx_adc.c
npcm7xx_adc_read(const char *id, uint64_t offset, uint32_t value) " %s offset: 0x%04" PRIx64 " value 0x%04" PRIx32
npcm7xx_adc_write(const char *id, uint64_t offset, uint32_t value) "%s offset: 0x%04" PRIx64 " value 0x%04" PRIx32
+
+aspeed_adc_engine_read(uint32_t engine_id, uint64_t addr, uint64_t value) "engine[%u] 0x%" PRIx64 " 0x%" PRIx64
+aspeed_adc_engine_write(uint32_t engine_id, uint64_t addr, uint64_t value) "engine[%u] 0x%" PRIx64 " 0x%" PRIx64
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 16/18] hw/arm: Integrate ADC model into Aspeed SoC
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (14 preceding siblings ...)
2021-10-12 7:37 ` [PULL 15/18] hw/adc: Add basic Aspeed ADC model Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 17/18] aspeed/wdt: Add trace events Cédric Le Goater
` (2 subsequent siblings)
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, qemu-devel, qemu-arm, Cédric Le Goater,
Peter Delevoryas, Joel Stanley
From: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Peter Delevoryas <pdel@fb.com>
Message-Id: <20211005052604.1674891-3-pdel@fb.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
include/hw/arm/aspeed_soc.h | 2 ++
hw/arm/aspeed_ast2600.c | 11 +++++++++++
hw/arm/aspeed_soc.c | 11 +++++++++++
3 files changed, 24 insertions(+)
diff --git a/include/hw/arm/aspeed_soc.h b/include/hw/arm/aspeed_soc.h
index 87d76c92598b..8139358549df 100644
--- a/include/hw/arm/aspeed_soc.h
+++ b/include/hw/arm/aspeed_soc.h
@@ -15,6 +15,7 @@
#include "hw/cpu/a15mpcore.h"
#include "hw/intc/aspeed_vic.h"
#include "hw/misc/aspeed_scu.h"
+#include "hw/adc/aspeed_adc.h"
#include "hw/misc/aspeed_sdmc.h"
#include "hw/misc/aspeed_xdma.h"
#include "hw/timer/aspeed_timer.h"
@@ -53,6 +54,7 @@ struct AspeedSoCState {
AspeedSCUState scu;
AspeedHACEState hace;
AspeedXDMAState xdma;
+ AspeedADCState adc;
AspeedSMCState fmc;
AspeedSMCState spi[ASPEED_SPIS_NUM];
EHCISysBusState ehci[ASPEED_EHCIS_NUM];
diff --git a/hw/arm/aspeed_ast2600.c b/hw/arm/aspeed_ast2600.c
index a70e4c48a73c..0384357a9510 100644
--- a/hw/arm/aspeed_ast2600.c
+++ b/hw/arm/aspeed_ast2600.c
@@ -148,6 +148,9 @@ static void aspeed_soc_ast2600_init(Object *obj)
snprintf(typename, sizeof(typename), "aspeed.timer-%s", socname);
object_initialize_child(obj, "timerctrl", &s->timerctrl, typename);
+ snprintf(typename, sizeof(typename), "aspeed.adc-%s", socname);
+ object_initialize_child(obj, "adc", &s->adc, typename);
+
snprintf(typename, sizeof(typename), "aspeed.i2c-%s", socname);
object_initialize_child(obj, "i2c", &s->i2c, typename);
@@ -322,6 +325,14 @@ static void aspeed_soc_ast2600_realize(DeviceState *dev, Error **errp)
sysbus_connect_irq(SYS_BUS_DEVICE(&s->timerctrl), i, irq);
}
+ /* ADC */
+ if (!sysbus_realize(SYS_BUS_DEVICE(&s->adc), errp)) {
+ return;
+ }
+ sysbus_mmio_map(SYS_BUS_DEVICE(&s->adc), 0, sc->memmap[ASPEED_DEV_ADC]);
+ sysbus_connect_irq(SYS_BUS_DEVICE(&s->adc), 0,
+ aspeed_soc_get_irq(s, ASPEED_DEV_ADC));
+
/* UART - attach an 8250 to the IO space as our UART */
serial_mm_init(get_system_memory(), sc->memmap[s->uart_default], 2,
aspeed_soc_get_irq(s, s->uart_default), 38400,
diff --git a/hw/arm/aspeed_soc.c b/hw/arm/aspeed_soc.c
index 4f013dd5cd9c..7d53cf2f5133 100644
--- a/hw/arm/aspeed_soc.c
+++ b/hw/arm/aspeed_soc.c
@@ -162,6 +162,9 @@ static void aspeed_soc_init(Object *obj)
snprintf(typename, sizeof(typename), "aspeed.timer-%s", socname);
object_initialize_child(obj, "timerctrl", &s->timerctrl, typename);
+ snprintf(typename, sizeof(typename), "aspeed.adc-%s", socname);
+ object_initialize_child(obj, "adc", &s->adc, typename);
+
snprintf(typename, sizeof(typename), "aspeed.i2c-%s", socname);
object_initialize_child(obj, "i2c", &s->i2c, typename);
@@ -287,6 +290,14 @@ static void aspeed_soc_realize(DeviceState *dev, Error **errp)
sysbus_connect_irq(SYS_BUS_DEVICE(&s->timerctrl), i, irq);
}
+ /* ADC */
+ if (!sysbus_realize(SYS_BUS_DEVICE(&s->adc), errp)) {
+ return;
+ }
+ sysbus_mmio_map(SYS_BUS_DEVICE(&s->adc), 0, sc->memmap[ASPEED_DEV_ADC]);
+ sysbus_connect_irq(SYS_BUS_DEVICE(&s->adc), 0,
+ aspeed_soc_get_irq(s, ASPEED_DEV_ADC));
+
/* UART - attach an 8250 to the IO space as our UART */
serial_mm_init(get_system_memory(), sc->memmap[s->uart_default], 2,
aspeed_soc_get_irq(s, s->uart_default), 38400,
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 17/18] aspeed/wdt: Add trace events
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (15 preceding siblings ...)
2021-10-12 7:37 ` [PULL 16/18] hw/arm: Integrate ADC model into Aspeed SoC Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 7:37 ` [PULL 18/18] aspeed/smc: Dump address offset in " Cédric Le Goater
2021-10-12 13:15 ` [PULL 00/18] aspeed queue Richard Henderson
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Francisco Iglesias, qemu-devel, qemu-arm,
Cédric Le Goater, Joel Stanley
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
hw/watchdog/wdt_aspeed.c | 5 +++++
hw/watchdog/trace-events | 4 ++++
2 files changed, 9 insertions(+)
diff --git a/hw/watchdog/wdt_aspeed.c b/hw/watchdog/wdt_aspeed.c
index 69c37af9a6e9..146ffcd71301 100644
--- a/hw/watchdog/wdt_aspeed.c
+++ b/hw/watchdog/wdt_aspeed.c
@@ -19,6 +19,7 @@
#include "hw/sysbus.h"
#include "hw/watchdog/wdt_aspeed.h"
#include "migration/vmstate.h"
+#include "trace.h"
#define WDT_STATUS (0x00 / 4)
#define WDT_RELOAD_VALUE (0x04 / 4)
@@ -60,6 +61,8 @@ static uint64_t aspeed_wdt_read(void *opaque, hwaddr offset, unsigned size)
{
AspeedWDTState *s = ASPEED_WDT(opaque);
+ trace_aspeed_wdt_read(offset, size);
+
offset >>= 2;
switch (offset) {
@@ -140,6 +143,8 @@ static void aspeed_wdt_write(void *opaque, hwaddr offset, uint64_t data,
AspeedWDTClass *awc = ASPEED_WDT_GET_CLASS(s);
bool enable;
+ trace_aspeed_wdt_write(offset, size, data);
+
offset >>= 2;
switch (offset) {
diff --git a/hw/watchdog/trace-events b/hw/watchdog/trace-events
index c3bafbffa911..e7523e22aaf2 100644
--- a/hw/watchdog/trace-events
+++ b/hw/watchdog/trace-events
@@ -5,3 +5,7 @@ cmsdk_apb_watchdog_read(uint64_t offset, uint64_t data, unsigned size) "CMSDK AP
cmsdk_apb_watchdog_write(uint64_t offset, uint64_t data, unsigned size) "CMSDK APB watchdog write: offset 0x%" PRIx64 " data 0x%" PRIx64 " size %u"
cmsdk_apb_watchdog_reset(void) "CMSDK APB watchdog: reset"
cmsdk_apb_watchdog_lock(uint32_t lock) "CMSDK APB watchdog: lock %" PRIu32
+
+# wdt-aspeed.c
+aspeed_wdt_read(uint64_t addr, uint32_t size) "@0x%" PRIx64 " size=%d"
+aspeed_wdt_write(uint64_t addr, uint32_t size, uint64_t data) "@0x%" PRIx64 " size=%d value=0x%"PRIx64
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* [PULL 18/18] aspeed/smc: Dump address offset in trace events
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (16 preceding siblings ...)
2021-10-12 7:37 ` [PULL 17/18] aspeed/wdt: Add trace events Cédric Le Goater
@ 2021-10-12 7:37 ` Cédric Le Goater
2021-10-12 13:15 ` [PULL 00/18] aspeed queue Richard Henderson
18 siblings, 0 replies; 20+ messages in thread
From: Cédric Le Goater @ 2021-10-12 7:37 UTC (permalink / raw)
To: Peter Maydell
Cc: Andrew Jeffery, Francisco Iglesias, qemu-devel, qemu-arm,
Cédric Le Goater, Joel Stanley
The register index is currently printed and this is confusing.
Reviewed-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
---
hw/ssi/aspeed_smc.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/hw/ssi/aspeed_smc.c b/hw/ssi/aspeed_smc.c
index 7129341c129e..8a988c167604 100644
--- a/hw/ssi/aspeed_smc.c
+++ b/hw/ssi/aspeed_smc.c
@@ -728,7 +728,7 @@ static uint64_t aspeed_smc_read(void *opaque, hwaddr addr, unsigned int size)
addr < R_SEG_ADDR0 + asc->max_peripherals) ||
(addr >= s->r_ctrl0 && addr < s->r_ctrl0 + asc->max_peripherals)) {
- trace_aspeed_smc_read(addr, size, s->regs[addr]);
+ trace_aspeed_smc_read(addr << 2, size, s->regs[addr]);
return s->regs[addr];
} else {
@@ -1029,10 +1029,10 @@ static void aspeed_smc_write(void *opaque, hwaddr addr, uint64_t data,
AspeedSMCClass *asc = ASPEED_SMC_GET_CLASS(s);
uint32_t value = data;
- addr >>= 2;
-
trace_aspeed_smc_write(addr, size, data);
+ addr >>= 2;
+
if (addr == s->r_conf ||
(addr >= s->r_timings &&
addr < s->r_timings + asc->nregs_timings) ||
--
2.31.1
^ permalink raw reply related [flat|nested] 20+ messages in thread* Re: [PULL 00/18] aspeed queue
2021-10-12 7:37 [PULL 00/18] aspeed queue Cédric Le Goater
` (17 preceding siblings ...)
2021-10-12 7:37 ` [PULL 18/18] aspeed/smc: Dump address offset in " Cédric Le Goater
@ 2021-10-12 13:15 ` Richard Henderson
18 siblings, 0 replies; 20+ messages in thread
From: Richard Henderson @ 2021-10-12 13:15 UTC (permalink / raw)
To: Cédric Le Goater, Peter Maydell
Cc: Andrew Jeffery, qemu-arm, Joel Stanley, qemu-devel
On 10/12/21 12:37 AM, Cédric Le Goater wrote:
> The following changes since commit c09124dcb8401a0d635b4a52b295e9b3fc12392a:
>
> Merge remote-tracking branch 'remotes/stefanha/tags/block-pull-request' into staging (2021-10-11 08:15:32 -0700)
>
> are available in the Git repository at:
>
> https://github.com/legoater/qemu/ tags/pull-aspeed-20211012
>
> for you to fetch changes up to e2804a1ec97ceede14b69a2a6e9a8b5dfa0b15c2:
>
> aspeed/smc: Dump address offset in trace events (2021-10-12 08:20:08 +0200)
>
> ----------------------------------------------------------------
> Aspeed patches :
>
> * I2C QOMify (Cedric)
> * SMC model cleanup and QOMify (Cedric)
> * ADC model (Peter and Andrew)
> * GPIO fixes (Peter)
>
> ----------------------------------------------------------------
> Andrew Jeffery (2):
> hw/adc: Add basic Aspeed ADC model
> hw/arm: Integrate ADC model into Aspeed SoC
>
> Cédric Le Goater (14):
> aspeed/smc: Add watchdog Control/Status Registers
> aspeed/smc: Introduce aspeed_smc_error() helper
> aspeed/smc: Stop using the model name for the memory regions
> aspeed/smc: Drop AspeedSMCController structure
> aspeed/smc: Remove the 'flash' attribute from AspeedSMCFlash
> aspeed/smc: Remove the 'size' attribute from AspeedSMCFlash
> aspeed/smc: Rename AspeedSMCFlash 'id' to 'cs'
> aspeed/smc: QOMify AspeedSMCFlash
> aspeed/smc: Add default reset values
> aspeed/smc: Introduce a new addr_width() class handler
> aspeed/smc: Remove unused attribute 'irqline'
> aspeed/i2c: QOMify AspeedI2CBus
> aspeed/wdt: Add trace events
> aspeed/smc: Dump address offset in trace events
>
> Peter Delevoryas (2):
> hw: aspeed_gpio: Fix pin I/O type declarations
> hw: aspeed_gpio: Fix GPIO array indexing
>
> include/hw/adc/aspeed_adc.h | 55 ++
> include/hw/arm/aspeed_soc.h | 2 +
> include/hw/gpio/aspeed_gpio.h | 5 +-
> include/hw/i2c/aspeed_i2c.h | 8 +-
> include/hw/ssi/aspeed_smc.h | 82 ++-
> hw/adc/aspeed_adc.c | 427 ++++++++++++++++
> hw/arm/aspeed.c | 18 +-
> hw/arm/aspeed_ast2600.c | 22 +-
> hw/arm/aspeed_soc.c | 15 +-
> hw/gpio/aspeed_gpio.c | 88 ++--
> hw/i2c/aspeed_i2c.c | 101 +++-
> hw/ssi/aspeed_smc.c | 1134 +++++++++++++++++++++++------------------
> hw/watchdog/wdt_aspeed.c | 5 +
> hw/adc/meson.build | 1 +
> hw/adc/trace-events | 3 +
> hw/watchdog/trace-events | 4 +
> 16 files changed, 1352 insertions(+), 618 deletions(-)
> create mode 100644 include/hw/adc/aspeed_adc.h
> create mode 100644 hw/adc/aspeed_adc.c
Applied, thanks.
r~
^ permalink raw reply [flat|nested] 20+ messages in thread