[PATCH 4/4] pnv/xive2: Handle TIMA access through all ports

[Frederic Barrat <fbarrat@linux.ibm.com>]

The Thread Interrupt Management Area (TIMA) can be accessed through 4
ports/snoop buses, targeted by the address. The base address of a TIMA
is using port 0 and the other ports are 0x80 apart. Using one port or
another can be useful to balance the load on the snoop buses.

The TIMA registers are in the 0x0 -> 0x3F range and there are 2
indication bits for special operations (bits 10 and 11; everything
fits on a 4k page). So the port address bits fall in between and are
"don't care" for the hardware when processing the TIMA operation. So
this patch filters out those port address bits so that a TIMA
operation can be triggered using any port.

It is also true for indirect access (through the IC BAR) and it's
actually nothing new, it was already the case on P9. Which helps here,
as the TIMA handling code is common between P9 (xive) and P10 (xive2).

Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
---
 hw/intc/pnv_xive2.c |  4 ++++
 hw/intc/xive.c      | 18 ++++++++++++++++++
 2 files changed, 22 insertions(+)

diff --git a/hw/intc/pnv_xive2.c b/hw/intc/pnv_xive2.c
index 132f82a035..c80316657a 100644
--- a/hw/intc/pnv_xive2.c
+++ b/hw/intc/pnv_xive2.c
@@ -1662,6 +1662,8 @@ static void pnv_xive2_tm_write(void *opaque, hwaddr offset,
     bool gen1_tima_os =
         xive->cq_regs[CQ_XIVE_CFG >> 3] & CQ_XIVE_CFG_GEN1_TIMA_OS;
 
+    offset &= 0xC3F; /* See comment in xive_tctx_tm_write() */
+
     /* TODO: should we switch the TM ops table instead ? */
     if (!gen1_tima_os && offset == HV_PUSH_OS_CTX_OFFSET) {
         xive2_tm_push_os_ctx(xptr, tctx, offset, value, size);
@@ -1681,6 +1683,8 @@ static uint64_t pnv_xive2_tm_read(void *opaque, hwaddr offset, unsigned size)
     bool gen1_tima_os =
         xive->cq_regs[CQ_XIVE_CFG >> 3] & CQ_XIVE_CFG_GEN1_TIMA_OS;
 
+    offset &= 0xC3F; /* See comment in xive_tctx_tm_read() */
+
     /* TODO: should we switch the TM ops table instead ? */
     if (!gen1_tima_os && offset == HV_PULL_OS_CTX_OFFSET) {
         return xive2_tm_pull_os_ctx(xptr, tctx, offset, size);
diff --git a/hw/intc/xive.c b/hw/intc/xive.c
index a986b96843..c1abfae31d 100644
--- a/hw/intc/xive.c
+++ b/hw/intc/xive.c
@@ -527,6 +527,15 @@ void xive_tctx_tm_write(XivePresenter *xptr, XiveTCTX *tctx, hwaddr offset,
 
     trace_xive_tctx_tm_write(offset, size, value);
 
+    /*
+     * The TIMA can be accessed through 4 ports/snoop buses, with
+     * addresses 0x80 apart.
+     * However, the offset bits between the "special op" bits and the
+     * MSB of the range used for the TIMA registers are "don't care"
+     * for the hardware, so we filter them out.
+     */
+    offset &= 0xC3F;
+
     /*
      * TODO: check V bit in Q[0-3]W2
      */
@@ -566,6 +575,15 @@ uint64_t xive_tctx_tm_read(XivePresenter *xptr, XiveTCTX *tctx, hwaddr offset,
     const XiveTmOp *xto;
     uint64_t ret;
 
+    /*
+     * The TIMA can be accessed through 4 ports/snoop buses, with
+     * addresses 0x80 apart.
+     * However, the offset bits between the "special op" bits and the
+     * MSB of the range used for the TIMA registers are "don't care"
+     * for the hardware, so we filter them out.
+     */
+    offset &= 0xC3F;
+
     /*
      * TODO: check V bit in Q[0-3]W2
      */
-- 
2.40.1