[PULL 20/20] mac_via: extend timer calibration hack to work with A/UX

[Laurent Vivier <laurent@vivier.eu>]

From: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>

The A/UX timer calibration loop runs continuously until 2 consecutive iterations
differ by at least 0x492 timer ticks. Modern hosts execute the timer calibration
loop so fast that this situation never occurs causing a hang on boot.

Use a similar method to Shoebill which is to randomly add 0x500 to the T2
counter value during calibration to enable it to eventually succeed.

Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Laurent Vivier <laurent@vivier.eu>
Message-ID: <20231004083806.757242-21-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
---
 hw/misc/mac_via.c | 56 +++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 56 insertions(+)

diff --git a/hw/misc/mac_via.c b/hw/misc/mac_via.c
index 500ece5872bd..b6206ef73ca7 100644
--- a/hw/misc/mac_via.c
+++ b/hw/misc/mac_via.c
@@ -983,6 +983,44 @@ static void via1_timer_calibration_hack(MOS6522Q800VIA1State *v1s, int addr,
             /* Looks like there has been a reset? */
             v1s->timer_hack_state = 1;
         }
+
+        if (addr == VIA_REG_T2CL && val == 0xf0) {
+            /* VIA_REG_T2CL: low byte of counter (A/UX) */
+            v1s->timer_hack_state = 5;
+        }
+        break;
+    case 5:
+        if (addr == VIA_REG_T2CH && val == 0x3c) {
+            /*
+             * VIA_REG_T2CH: high byte of counter (A/UX). We are now extremely
+             * likely to be in the A/UX timer calibration routine, so move to
+             * the next state where we enable the calibration hack.
+             */
+            v1s->timer_hack_state = 6;
+        } else if ((addr == VIA_REG_IER && val == 0x20) ||
+                   addr == VIA_REG_T2CH) {
+            /* We're doing something else with the timer, not calibration */
+            v1s->timer_hack_state = 0;
+        }
+        break;
+    case 6:
+        if ((addr == VIA_REG_IER && val == 0x20) || addr == VIA_REG_T2CH) {
+            /* End of A/UX timer calibration routine, or another write */
+            v1s->timer_hack_state = 7;
+        } else {
+            v1s->timer_hack_state = 0;
+        }
+        break;
+    case 7:
+        /*
+         * This is the normal post-calibration timer state once both the
+         * MacOS toolbox and A/UX have been calibrated, until we see a write
+         * to VIA_REG_PCR to suggest a reset
+         */
+        if (addr == VIA_REG_PCR && val == 0x22) {
+            /* Looks like there has been a reset? */
+            v1s->timer_hack_state = 1;
+        }
         break;
     default:
         g_assert_not_reached();
@@ -998,6 +1036,7 @@ static uint64_t mos6522_q800_via1_read(void *opaque, hwaddr addr, unsigned size)
     MOS6522Q800VIA1State *s = MOS6522_Q800_VIA1(opaque);
     MOS6522State *ms = MOS6522(s);
     uint64_t ret;
+    int64_t now;
 
     addr = (addr >> 9) & 0xf;
     ret = mos6522_read(ms, addr, size);
@@ -1007,6 +1046,23 @@ static uint64_t mos6522_q800_via1_read(void *opaque, hwaddr addr, unsigned size)
         /* Quadra 800 Id */
         ret = (ret & ~VIA1A_CPUID_MASK) | VIA1A_CPUID_Q800;
         break;
+    case VIA_REG_T2CH:
+        if (s->timer_hack_state == 6) {
+            /*
+             * The A/UX timer calibration loop runs continuously until 2
+             * consecutive iterations differ by at least 0x492 timer ticks.
+             * Modern hosts execute the timer calibration loop so fast that
+             * this situation never occurs causing a hang on boot. Use a
+             * similar method to Shoebill which is to randomly add 0x500 to
+             * the T2 counter value during calibration to enable it to
+             * eventually succeed.
+             */
+            now = qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL);
+            if (now & 1) {
+                ret += 0x5;
+            }
+        }
+        break;
     }
     return ret;
 }
-- 
2.41.0