[PATCH v2 00/17] bsd-user: Comprehensive RISCV Support

[PATCH v2 00/17] bsd-user: Comprehensive RISCV Support

[Ajeet Singh]

Key Changes Compared to Version 1:
Patch 3: Array subscript was replaced by a register constant.
Patches 4 and 5: Merged into a single patch.
Patch 6: Comment was removed.
Patch 10: ROUND_DOWN was used to align the stack.
	  Array subscript was replaced by a register constant.
Patch 15: Register constants were used instead of array subscripts.

Mark Corbin (15):
  bsd-user: Implement RISC-V CPU initialization and main loop
  bsd-user: Add RISC-V CPU execution loop and syscall handling
  bsd-user: Implement RISC-V CPU register cloning and reset functions
  bsd-user: Implement RISC-V TLS register setup
  bsd-user: Add RISC-V ELF definitions and hardware capability detection
  bsd-user: Define RISC-V register structures and register copying
  bsd-user: Add RISC-V signal trampoline setup function
  bsd-user: Implement RISC-V sysarch system call emulation
  bsd-user: Add RISC-V thread setup and initialization support
  bsd-user: Define RISC-V VM parameters and helper functions
  bsd-user: Define RISC-V system call structures and constants
  bsd-user: Define RISC-V signal handling structures and constants
  bsd-user: Implement RISC-V signal trampoline setup functions
  bsd-user: Implement 'get_mcontext' for RISC-V
  bsd-user: Implement set_mcontext and get_ucontext_sigreturn for RISCV

Warner Losh (2):
  bsd-user: Add generic RISC-V64 target definitions
  bsd-user: Add RISC-V 64-bit Target Configuration and Debug XML Files

 bsd-user/riscv/signal.c               | 170 ++++++++++++++++++++++++++
 bsd-user/riscv/target.h               |  20 +++
 bsd-user/riscv/target_arch.h          |  27 ++++
 bsd-user/riscv/target_arch_cpu.c      |  29 +++++
 bsd-user/riscv/target_arch_cpu.h      | 147 ++++++++++++++++++++++
 bsd-user/riscv/target_arch_elf.h      |  42 +++++++
 bsd-user/riscv/target_arch_reg.h      |  88 +++++++++++++
 bsd-user/riscv/target_arch_signal.h   |  75 ++++++++++++
 bsd-user/riscv/target_arch_sigtramp.h |  46 +++++++
 bsd-user/riscv/target_arch_sysarch.h  |  41 +++++++
 bsd-user/riscv/target_arch_thread.h   |  47 +++++++
 bsd-user/riscv/target_arch_vmparam.h  |  53 ++++++++
 bsd-user/riscv/target_syscall.h       |  38 ++++++
 configs/targets/riscv64-bsd-user.mak  |   4 +
 14 files changed, 827 insertions(+)
 create mode 100644 bsd-user/riscv/signal.c
 create mode 100644 bsd-user/riscv/target.h
 create mode 100644 bsd-user/riscv/target_arch.h
 create mode 100644 bsd-user/riscv/target_arch_cpu.c
 create mode 100644 bsd-user/riscv/target_arch_cpu.h
 create mode 100644 bsd-user/riscv/target_arch_elf.h
 create mode 100644 bsd-user/riscv/target_arch_reg.h
 create mode 100644 bsd-user/riscv/target_arch_signal.h
 create mode 100644 bsd-user/riscv/target_arch_sigtramp.h
 create mode 100644 bsd-user/riscv/target_arch_sysarch.h
 create mode 100644 bsd-user/riscv/target_arch_thread.h
 create mode 100644 bsd-user/riscv/target_arch_vmparam.h
 create mode 100644 bsd-user/riscv/target_syscall.h
 create mode 100644 configs/targets/riscv64-bsd-user.mak

-- 
2.34.1

[PATCH v2 01/17] bsd-user: Implement RISC-V CPU initialization and main loop

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Added the initial implementation for RISC-V CPU initialization and main
loop. This includes setting up the general-purpose registers and
program counter based on the provided target architecture definitions.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Co-authored-by: Jessica Clarke <jrtc27@jrtc27.com>
---
 bsd-user/riscv/target_arch_cpu.h | 39 ++++++++++++++++++++++++++++++++
 1 file changed, 39 insertions(+)
 create mode 100644 bsd-user/riscv/target_arch_cpu.h

diff --git a/bsd-user/riscv/target_arch_cpu.h b/bsd-user/riscv/target_arch_cpu.h
new file mode 100644
index 0000000000..28f56560e0
--- /dev/null
+++ b/bsd-user/riscv/target_arch_cpu.h
@@ -0,0 +1,39 @@
+/*
+ *  RISC-V CPU init and loop
+ *
+ *  Copyright (c) 2019 Mark Corbin
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef TARGET_ARCH_CPU_H
+#define TARGET_ARCH_CPU_H
+
+#include "target_arch.h"
+
+#define TARGET_DEFAULT_CPU_MODEL "max"
+
+static inline void target_cpu_init(CPURISCVState *env,
+        struct target_pt_regs *regs)
+{
+    int i;
+
+    for (i = 0; i < 32; i++) {
+        env->gpr[i] = regs->regs[i];
+    }
+
+    env->pc = regs->sepc;
+}
+
+#endif /* TARGET_ARCH_CPU_H */
-- 
2.34.1

Re: [PATCH v2 01/17] bsd-user: Implement RISC-V CPU initialization and main loop

[Richard Henderson]

On 8/17/24 03:09, Ajeet Singh wrote:
> From: Mark Corbin <mark@dibsco.co.uk>
> 
> Added the initial implementation for RISC-V CPU initialization and main
> loop. This includes setting up the general-purpose registers and
> program counter based on the provided target architecture definitions.
> 
> Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
> Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
> Co-authored-by: Jessica Clarke <jrtc27@jrtc27.com>
> ---
>   bsd-user/riscv/target_arch_cpu.h | 39 ++++++++++++++++++++++++++++++++
>   1 file changed, 39 insertions(+)
>   create mode 100644 bsd-user/riscv/target_arch_cpu.h
> 
> diff --git a/bsd-user/riscv/target_arch_cpu.h b/bsd-user/riscv/target_arch_cpu.h
> new file mode 100644
> index 0000000000..28f56560e0
> --- /dev/null
> +++ b/bsd-user/riscv/target_arch_cpu.h
> @@ -0,0 +1,39 @@
> +/*
> + *  RISC-V CPU init and loop
> + *
> + *  Copyright (c) 2019 Mark Corbin
> + *
> + *  This program is free software; you can redistribute it and/or modify
> + *  it under the terms of the GNU General Public License as published by
> + *  the Free Software Foundation; either version 2 of the License, or
> + *  (at your option) any later version.
> + *
> + *  This program is distributed in the hope that it will be useful,
> + *  but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *  GNU General Public License for more details.
> + *
> + *  You should have received a copy of the GNU General Public License
> + *  along with this program; if not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#ifndef TARGET_ARCH_CPU_H
> +#define TARGET_ARCH_CPU_H
> +
> +#include "target_arch.h"
> +
> +#define TARGET_DEFAULT_CPU_MODEL "max"
> +
> +static inline void target_cpu_init(CPURISCVState *env,
> +        struct target_pt_regs *regs)
> +{
> +    int i;
> +
> +    for (i = 0; i < 32; i++) {
> +        env->gpr[i] = regs->regs[i];

Again, r0 is zero.  Clearer if we never set that outside of reset.

r~

> +    }
> +
> +    env->pc = regs->sepc;
> +}
> +
> +#endif /* TARGET_ARCH_CPU_H */

[PATCH v2 02/17] bsd-user: Add RISC-V CPU execution loop and syscall handling

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Implemented the RISC-V CPU execution loop, including handling various
exceptions and system calls. The loop continuously executes CPU
instructions,processes exceptions, and handles system calls by invoking
FreeBSD syscall handlers.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Co-authored-by: Jessica Clarke <jrtc27@jrtc27.com>
Co-authored-by: Kyle Evans <kevans@FreeBSD.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/target_arch_cpu.h | 94 ++++++++++++++++++++++++++++++++
 1 file changed, 94 insertions(+)

diff --git a/bsd-user/riscv/target_arch_cpu.h b/bsd-user/riscv/target_arch_cpu.h
index 28f56560e0..5b436b2ac9 100644
--- a/bsd-user/riscv/target_arch_cpu.h
+++ b/bsd-user/riscv/target_arch_cpu.h
@@ -36,4 +36,98 @@ static inline void target_cpu_init(CPURISCVState *env,
     env->pc = regs->sepc;
 }
 
+static inline void target_cpu_loop(CPURISCVState *env)
+{
+    CPUState *cs = env_cpu(env);
+    int trapnr;
+    abi_long ret;
+    unsigned int syscall_num;
+    int32_t signo, code;
+
+    for (;;) {
+        cpu_exec_start(cs);
+        trapnr = cpu_exec(cs);
+        cpu_exec_end(cs);
+        process_queued_cpu_work(cs);
+
+        signo = 0;
+
+        switch (trapnr) {
+        case EXCP_INTERRUPT:
+            /* just indicate that signals should be handled asap */
+            break;
+        case EXCP_ATOMIC:
+            cpu_exec_step_atomic(cs);
+            break;
+        case RISCV_EXCP_U_ECALL:
+            syscall_num = env->gpr[xT0]; /* t0 */
+            env->pc += TARGET_INSN_SIZE;
+            /* Compare to cpu_fetch_syscall_args() in riscv/riscv/trap.c */
+            if (TARGET_FREEBSD_NR___syscall == syscall_num ||
+                TARGET_FREEBSD_NR_syscall == syscall_num) {
+                ret = do_freebsd_syscall(env,
+                                         env->gpr[xA0], /* a0 */
+                                         env->gpr[xA1], /* a1 */
+                                         env->gpr[xA2], /* a2 */
+                                         env->gpr[xA3], /* a3 */
+                                         env->gpr[xA4], /* a4 */
+                                         env->gpr[xA5], /* a5 */
+                                         env->gpr[xA6], /* a6 */
+                                         env->gpr[xA7], /* a7 */
+                                         0);
+            } else {
+                ret = do_freebsd_syscall(env,
+                                         syscall_num,
+                                         env->gpr[xA0], /* a0 */
+                                         env->gpr[xA1], /* a1 */
+                                         env->gpr[xA2], /* a2 */
+                                         env->gpr[xA3], /* a3 */
+                                         env->gpr[xA4], /* a4 */
+                                         env->gpr[xA5], /* a5 */
+                                         env->gpr[xA6], /* a6 */
+                                         env->gpr[xA7]  /* a7 */
+                    );
+            }
+
+            /*
+             * Compare to cpu_set_syscall_retval() in
+             * riscv/riscv/vm_machdep.c
+             */
+            if (ret >= 0) {
+                env->gpr[xA0] = ret; /* a0 */
+                env->gpr[xT0] = 0;   /* t0 */
+            } else if (ret == -TARGET_ERESTART) {
+                env->pc -= TARGET_INSN_SIZE;
+            } else if (ret != -TARGET_EJUSTRETURN) {
+                env->gpr[xA0] = -ret; /* a0 */
+                env->gpr[xT0] = 1;   /* t0 */
+            }
+            break;
+        case RISCV_EXCP_ILLEGAL_INST:
+            signo = TARGET_SIGILL;
+            code = TARGET_ILL_ILLOPC;
+            break;
+        case RISCV_EXCP_BREAKPOINT:
+            signo = TARGET_SIGTRAP;
+            code = TARGET_TRAP_BRKPT;
+            break;
+        case EXCP_DEBUG:
+            signo = TARGET_SIGTRAP;
+            code = TARGET_TRAP_BRKPT;
+            break;
+        default:
+            fprintf(stderr, "qemu: unhandled CPU exception "
+                "0x%x - aborting\n", trapnr);
+            cpu_dump_state(cs, stderr, 0);
+            abort();
+        }
+
+        if (signo) {
+            force_sig_fault(signo, code, env->pc);
+        }
+
+        process_pending_signals(env);
+    }
+}
+
 #endif /* TARGET_ARCH_CPU_H */
-- 
2.34.1

[PATCH v2 03/17] bsd-user: Implement RISC-V CPU register cloning and reset functions

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Added functions for cloning CPU registers and resetting the CPU state
for RISC-V architecture.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/target_arch_cpu.h | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/bsd-user/riscv/target_arch_cpu.h b/bsd-user/riscv/target_arch_cpu.h
index 5b436b2ac9..bdb527573b 100644
--- a/bsd-user/riscv/target_arch_cpu.h
+++ b/bsd-user/riscv/target_arch_cpu.h
@@ -130,4 +130,18 @@ static inline void target_cpu_loop(CPURISCVState *env)
     }
 }
 
+static inline void target_cpu_clone_regs(CPURISCVState *env, target_ulong newsp)
+{
+    if (newsp) {
+        env->gpr[xSP] = newsp;
+    }
+
+    env->gpr[xA0] = 0; /* a0 */
+    env->gpr[xT0] = 0; /* t0 */
+}
+
+static inline void target_cpu_reset(CPUArchState *env)
+{
+}
+
 #endif /* TARGET_ARCH_CPU_H */
-- 
2.34.1

[PATCH v2 04/17] bsd-user: Implement RISC-V TLS register setup

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Included the prototype for the 'target_cpu_set_tls' function in the
'target_arch.h' header file. This function is responsible for setting
the Thread Local Storage (TLS) register for RISC-V architecture.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/target_arch.h     | 27 +++++++++++++++++++++++++++
 bsd-user/riscv/target_arch_cpu.c | 29 +++++++++++++++++++++++++++++
 2 files changed, 56 insertions(+)
 create mode 100644 bsd-user/riscv/target_arch.h
 create mode 100644 bsd-user/riscv/target_arch_cpu.c

diff --git a/bsd-user/riscv/target_arch.h b/bsd-user/riscv/target_arch.h
new file mode 100644
index 0000000000..26ce07f343
--- /dev/null
+++ b/bsd-user/riscv/target_arch.h
@@ -0,0 +1,27 @@
+/*
+ * RISC-V specific prototypes
+ *
+ * Copyright (c) 2019 Mark Corbin <mark.corbin@embecsom.com>
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public
+ * License as published by the Free Software Foundation; either
+ * version 2 of the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef TARGET_ARCH_H
+#define TARGET_ARCH_H
+
+#include "qemu.h"
+
+void target_cpu_set_tls(CPURISCVState *env, target_ulong newtls);
+
+#endif /* TARGET_ARCH_H */
diff --git a/bsd-user/riscv/target_arch_cpu.c b/bsd-user/riscv/target_arch_cpu.c
new file mode 100644
index 0000000000..44e25d2ddf
--- /dev/null
+++ b/bsd-user/riscv/target_arch_cpu.c
@@ -0,0 +1,29 @@
+/*
+ *  RISC-V CPU related code
+ *
+ *  Copyright (c) 2019 Mark Corbin
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+#include "qemu/osdep.h"
+
+#include "target_arch.h"
+
+#define TP_OFFSET       16
+
+/* Compare with cpu_set_user_tls() in riscv/riscv/vm_machdep.c */
+void target_cpu_set_tls(CPURISCVState *env, target_ulong newtls)
+{
+    env->gpr[xTP] = newtls + TP_OFFSET;
+}
-- 
2.34.1

[PATCH v2 05/17] bsd-user: Add RISC-V ELF definitions and hardware capability detection

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Introduced RISC-V specific ELF definitions and hardware capability
detection.
Additionally, a function to retrieve hardware capabilities
('get_elf_hwcap') is implemented, which returns the common bits set in
each CPU's ISA strings.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Co-authored-by: Kyle Evans <kevans@FreeBSD.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/target_arch_elf.h | 42 ++++++++++++++++++++++++++++++++
 1 file changed, 42 insertions(+)
 create mode 100644 bsd-user/riscv/target_arch_elf.h

diff --git a/bsd-user/riscv/target_arch_elf.h b/bsd-user/riscv/target_arch_elf.h
new file mode 100644
index 0000000000..4eb915e61e
--- /dev/null
+++ b/bsd-user/riscv/target_arch_elf.h
@@ -0,0 +1,42 @@
+/*
+ *  RISC-V ELF definitions
+ *
+ *  Copyright (c) 2019 Mark Corbin
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef TARGET_ARCH_ELF_H
+#define TARGET_ARCH_ELF_H
+
+#define elf_check_arch(x) ((x) == EM_RISCV)
+#define ELF_START_MMAP 0x80000000
+#define ELF_ET_DYN_LOAD_ADDR    0x100000
+#define ELF_CLASS   ELFCLASS64
+
+#define ELF_DATA    ELFDATA2LSB
+#define ELF_ARCH    EM_RISCV
+
+#define ELF_HWCAP get_elf_hwcap()
+static uint32_t get_elf_hwcap(void)
+{
+    RISCVCPU *cpu = RISCV_CPU(thread_cpu);
+
+    return cpu->env.misa_ext_mask;
+}
+
+#define USE_ELF_CORE_DUMP
+#define ELF_EXEC_PAGESIZE        4096
+
+#endif /* TARGET_ARCH_ELF_H */
-- 
2.34.1

[PATCH v2 06/17] bsd-user: Define RISC-V register structures and register copying

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Added definitions for RISC-V register structures, including
general-purpose registers and floating-point registers, in
'target_arch_reg.h'. Implemented the 'target_copy_regs' function to
copy register values from the CPU state to the target register
structure, ensuring proper endianness handling using 'tswapreg'.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/target_arch_reg.h | 88 ++++++++++++++++++++++++++++++++
 1 file changed, 88 insertions(+)
 create mode 100644 bsd-user/riscv/target_arch_reg.h

diff --git a/bsd-user/riscv/target_arch_reg.h b/bsd-user/riscv/target_arch_reg.h
new file mode 100644
index 0000000000..12b1c96b61
--- /dev/null
+++ b/bsd-user/riscv/target_arch_reg.h
@@ -0,0 +1,88 @@
+/*
+ *  RISC-V register structures
+ *
+ *  Copyright (c) 2019 Mark Corbin
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef TARGET_ARCH_REG_H
+#define TARGET_ARCH_REG_H
+
+/* Compare with riscv/include/reg.h */
+typedef struct target_reg {
+    uint64_t ra;            /* return address */
+    uint64_t sp;            /* stack pointer */
+    uint64_t gp;            /* global pointer */
+    uint64_t tp;            /* thread pointer */
+    uint64_t t[7];          /* temporaries */
+    uint64_t s[12];         /* saved registers */
+    uint64_t a[8];          /* function arguments */
+    uint64_t sepc;          /* exception program counter */
+    uint64_t sstatus;       /* status register */
+} target_reg_t;
+
+typedef struct target_fpreg {
+    uint64_t        fp_x[32][2];    /* Floating point registers */
+    uint64_t        fp_fcsr;        /* Floating point control reg */
+} target_fpreg_t;
+
+#define tswapreg(ptr)   tswapal(ptr)
+
+/* Compare with struct trapframe in riscv/include/frame.h */
+static inline void target_copy_regs(target_reg_t *regs,
+                                    const CPURISCVState *env)
+{
+
+    regs->ra = tswapreg(env->gpr[1]);
+    regs->sp = tswapreg(env->gpr[2]);
+    regs->gp = tswapreg(env->gpr[3]);
+    regs->tp = tswapreg(env->gpr[4]);
+
+    regs->t[0] = tswapreg(env->gpr[5]);
+    regs->t[1] = tswapreg(env->gpr[6]);
+    regs->t[2] = tswapreg(env->gpr[7]);
+    regs->t[3] = tswapreg(env->gpr[28]);
+    regs->t[4] = tswapreg(env->gpr[29]);
+    regs->t[5] = tswapreg(env->gpr[30]);
+    regs->t[6] = tswapreg(env->gpr[31]);
+
+    regs->s[0] = tswapreg(env->gpr[8]);
+    regs->s[1] = tswapreg(env->gpr[9]);
+    regs->s[2] = tswapreg(env->gpr[18]);
+    regs->s[3] = tswapreg(env->gpr[19]);
+    regs->s[4] = tswapreg(env->gpr[20]);
+    regs->s[5] = tswapreg(env->gpr[21]);
+    regs->s[6] = tswapreg(env->gpr[22]);
+    regs->s[7] = tswapreg(env->gpr[23]);
+    regs->s[8] = tswapreg(env->gpr[24]);
+    regs->s[9] = tswapreg(env->gpr[25]);
+    regs->s[10] = tswapreg(env->gpr[26]);
+    regs->s[11] = tswapreg(env->gpr[27]);
+
+    regs->a[0] = tswapreg(env->gpr[10]);
+    regs->a[1] = tswapreg(env->gpr[11]);
+    regs->a[2] = tswapreg(env->gpr[12]);
+    regs->a[3] = tswapreg(env->gpr[13]);
+    regs->a[4] = tswapreg(env->gpr[14]);
+    regs->a[5] = tswapreg(env->gpr[15]);
+    regs->a[6] = tswapreg(env->gpr[16]);
+    regs->a[7] = tswapreg(env->gpr[17]);
+
+    regs->sepc = tswapreg(env->pc);
+}
+
+#undef tswapreg
+
+#endif /* TARGET_ARCH_REG_H */
-- 
2.34.1

[PATCH v2 07/17] bsd-user: Add RISC-V signal trampoline setup function

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Implemented the `setup_sigtramp` function for setting up the signal
trampoline code in the RISC-V architecture.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/target_arch_sigtramp.h | 46 +++++++++++++++++++++++++++
 1 file changed, 46 insertions(+)
 create mode 100644 bsd-user/riscv/target_arch_sigtramp.h

diff --git a/bsd-user/riscv/target_arch_sigtramp.h b/bsd-user/riscv/target_arch_sigtramp.h
new file mode 100644
index 0000000000..39c878db22
--- /dev/null
+++ b/bsd-user/riscv/target_arch_sigtramp.h
@@ -0,0 +1,46 @@
+/*
+ * RISC-V sigcode
+ *
+ * Copyright (c) 2019 Mark Corbin
+ *
+ * This library is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU Lesser General Public
+ * License as published by the Free Software Foundation; either
+ * version 2 of the License, or (at your option) any later version.
+ *
+ * This library is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+ * Lesser General Public License for more details.
+ *
+ * You should have received a copy of the GNU Lesser General Public
+ * License along with this library; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef TARGET_ARCH_SIGTRAMP_H
+#define TARGET_ARCH_SIGTRAMP_H
+
+/* Compare with sigcode() in riscv/riscv/locore.S */
+static inline abi_long setup_sigtramp(abi_ulong offset, unsigned sigf_uc,
+        unsigned sys_sigreturn)
+{
+    int i;
+    uint32_t sys_exit = TARGET_FREEBSD_NR_exit;
+
+    uint32_t sigtramp_code[] = {
+    /* 1 */ 0x00010513,                         /* mv a0, sp */
+    /* 2 */ 0x00050513 + (sigf_uc << 20),       /* addi a0, a0, sigf_uc */
+    /* 3 */ 0x00000293 + (sys_sigreturn << 20), /* li t0, sys_sigreturn */
+    /* 4 */ 0x00000073,                         /* ecall */
+    /* 5 */ 0x00000293 + (sys_exit << 20),      /* li t0, sys_exit */
+    /* 6 */ 0x00000073,                         /* ecall */
+    /* 7 */ 0xFF1FF06F                          /* b -16 */
+    };
+
+    for (i = 0; i < 7; i++) {
+        tswap32s(&sigtramp_code[i]);
+    }
+
+    return memcpy_to_target(offset, sigtramp_code, TARGET_SZSIGCODE);
+}
+#endif /* TARGET_ARCH_SIGTRAMP_H */
-- 
2.34.1

Re: [PATCH v2 07/17] bsd-user: Add RISC-V signal trampoline setup function

[Richard Henderson]

On 8/17/24 03:09, Ajeet Singh wrote:
> From: Mark Corbin <mark@dibsco.co.uk>
> 
> Implemented the `setup_sigtramp` function for setting up the signal
> trampoline code in the RISC-V architecture.
> 
> Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
> Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
> Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
> ---
>   bsd-user/riscv/target_arch_sigtramp.h | 46 +++++++++++++++++++++++++++
>   1 file changed, 46 insertions(+)
>   create mode 100644 bsd-user/riscv/target_arch_sigtramp.h
> 
> diff --git a/bsd-user/riscv/target_arch_sigtramp.h b/bsd-user/riscv/target_arch_sigtramp.h
> new file mode 100644
> index 0000000000..39c878db22
> --- /dev/null
> +++ b/bsd-user/riscv/target_arch_sigtramp.h
> @@ -0,0 +1,46 @@
> +/*
> + * RISC-V sigcode
> + *
> + * Copyright (c) 2019 Mark Corbin
> + *
> + * This library is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU Lesser General Public
> + * License as published by the Free Software Foundation; either
> + * version 2 of the License, or (at your option) any later version.
> + *
> + * This library is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
> + * Lesser General Public License for more details.
> + *
> + * You should have received a copy of the GNU Lesser General Public
> + * License along with this library; if not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#ifndef TARGET_ARCH_SIGTRAMP_H
> +#define TARGET_ARCH_SIGTRAMP_H
> +
> +/* Compare with sigcode() in riscv/riscv/locore.S */
> +static inline abi_long setup_sigtramp(abi_ulong offset, unsigned sigf_uc,
> +        unsigned sys_sigreturn)
> +{
> +    int i;
> +    uint32_t sys_exit = TARGET_FREEBSD_NR_exit;
> +
> +    uint32_t sigtramp_code[] = {
> +    /* 1 */ 0x00010513,                         /* mv a0, sp */
> +    /* 2 */ 0x00050513 + (sigf_uc << 20),       /* addi a0, a0, sigf_uc */
> +    /* 3 */ 0x00000293 + (sys_sigreturn << 20), /* li t0, sys_sigreturn */
> +    /* 4 */ 0x00000073,                         /* ecall */
> +    /* 5 */ 0x00000293 + (sys_exit << 20),      /* li t0, sys_exit */
> +    /* 6 */ 0x00000073,                         /* ecall */
> +    /* 7 */ 0xFF1FF06F                          /* b -16 */
> +    };
> +
> +    for (i = 0; i < 7; i++) {
> +        tswap32s(&sigtramp_code[i]);
> +    }

Use

     static const uint32_t sigtramp_code[] = {
         const_le32(...),
     };


r~

> +
> +    return memcpy_to_target(offset, sigtramp_code, TARGET_SZSIGCODE);
> +}
> +#endif /* TARGET_ARCH_SIGTRAMP_H */

[PATCH v2 08/17] bsd-user: Implement RISC-V sysarch system call emulation

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Added the 'do_freebsd_arch_sysarch' function to emulate the 'sysarch'
system call for the RISC-V architecture.
Currently, this function returns '-TARGET_EOPNOTSUPP' to indicate that
the operation is not supported.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/target_arch_sysarch.h | 41 ++++++++++++++++++++++++++++
 1 file changed, 41 insertions(+)
 create mode 100644 bsd-user/riscv/target_arch_sysarch.h

diff --git a/bsd-user/riscv/target_arch_sysarch.h b/bsd-user/riscv/target_arch_sysarch.h
new file mode 100644
index 0000000000..9af42331b4
--- /dev/null
+++ b/bsd-user/riscv/target_arch_sysarch.h
@@ -0,0 +1,41 @@
+/*
+ *  RISC-V sysarch() system call emulation
+ *
+ *  Copyright (c) 2019 Mark Corbin
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef TARGET_ARCH_SYSARCH_H
+#define TARGET_ARCH_SYSARCH_H
+
+#include "target_syscall.h"
+#include "target_arch.h"
+
+static inline abi_long do_freebsd_arch_sysarch(CPURISCVState *env, int op,
+        abi_ulong parms)
+{
+
+    return -TARGET_EOPNOTSUPP;
+}
+
+static inline void do_freebsd_arch_print_sysarch(
+        const struct syscallname *name, abi_long arg1, abi_long arg2,
+        abi_long arg3, abi_long arg4, abi_long arg5, abi_long arg6)
+{
+
+    gemu_log("UNKNOWN OP: %d, " TARGET_ABI_FMT_lx ")", (int)arg1, arg2);
+}
+
+#endif /* TARGET_ARCH_SYSARCH_H */
-- 
2.34.1

[PATCH v2 09/17] bsd-user: Add RISC-V thread setup and initialization support

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Implemented functions for setting up and initializing threads in the
RISC-V architecture.
The 'target_thread_set_upcall' function sets up the stack pointer,
program counter, and function argument for new threads.
The 'target_thread_init' function initializes thread registers based on
the provided image information.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Co-authored-by: Jessica Clarke <jrtc27@jrtc27.com>
Co-authored-by: Kyle Evans <kevans@FreeBSD.org>
---
 bsd-user/riscv/target_arch_thread.h | 47 +++++++++++++++++++++++++++++
 1 file changed, 47 insertions(+)
 create mode 100644 bsd-user/riscv/target_arch_thread.h

diff --git a/bsd-user/riscv/target_arch_thread.h b/bsd-user/riscv/target_arch_thread.h
new file mode 100644
index 0000000000..4596d3d51f
--- /dev/null
+++ b/bsd-user/riscv/target_arch_thread.h
@@ -0,0 +1,47 @@
+/*
+ *  RISC-V thread support
+ *
+ *  Copyright (c) 2019 Mark Corbin
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef TARGET_ARCH_THREAD_H
+#define TARGET_ARCH_THREAD_H
+
+/* Compare with cpu_set_upcall() in riscv/riscv/vm_machdep.c */
+static inline void target_thread_set_upcall(CPURISCVState *regs,
+    abi_ulong entry, abi_ulong arg, abi_ulong stack_base,
+    abi_ulong stack_size)
+{
+    abi_ulong sp;
+
+    sp = (abi_ulong)(stack_base + stack_size) & ~(16 - 1);
+
+    regs->gpr[xSP] = sp;
+    regs->pc = entry;
+    regs->gpr[xA0] = arg;
+}
+
+/* Compare with exec_setregs() in riscv/riscv/machdep.c */
+static inline void target_thread_init(struct target_pt_regs *regs,
+    struct image_info *infop)
+{
+    regs->sepc = infop->entry;
+    regs->regs[xRA] = infop->entry;
+    regs->regs[xA0] = infop->start_stack;               
+    regs->regs[xSP] = ROUND_DOWN(infop->start_stack,16);
+}
+
+#endif /* TARGET_ARCH_THREAD_H */
-- 
2.34.1

Re: [PATCH v2 09/17] bsd-user: Add RISC-V thread setup and initialization support

[Richard Henderson]

On 8/17/24 03:09, Ajeet Singh wrote:
> From: Mark Corbin <mark@dibsco.co.uk>
> 
> Implemented functions for setting up and initializing threads in the
> RISC-V architecture.
> The 'target_thread_set_upcall' function sets up the stack pointer,
> program counter, and function argument for new threads.
> The 'target_thread_init' function initializes thread registers based on
> the provided image information.
> 
> Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
> Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
> Co-authored-by: Jessica Clarke <jrtc27@jrtc27.com>
> Co-authored-by: Kyle Evans <kevans@FreeBSD.org>
> ---
>   bsd-user/riscv/target_arch_thread.h | 47 +++++++++++++++++++++++++++++
>   1 file changed, 47 insertions(+)
>   create mode 100644 bsd-user/riscv/target_arch_thread.h
> 
> diff --git a/bsd-user/riscv/target_arch_thread.h b/bsd-user/riscv/target_arch_thread.h
> new file mode 100644
> index 0000000000..4596d3d51f
> --- /dev/null
> +++ b/bsd-user/riscv/target_arch_thread.h
> @@ -0,0 +1,47 @@
> +/*
> + *  RISC-V thread support
> + *
> + *  Copyright (c) 2019 Mark Corbin
> + *
> + *  This program is free software; you can redistribute it and/or modify
> + *  it under the terms of the GNU General Public License as published by
> + *  the Free Software Foundation; either version 2 of the License, or
> + *  (at your option) any later version.
> + *
> + *  This program is distributed in the hope that it will be useful,
> + *  but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *  GNU General Public License for more details.
> + *
> + *  You should have received a copy of the GNU General Public License
> + *  along with this program; if not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#ifndef TARGET_ARCH_THREAD_H
> +#define TARGET_ARCH_THREAD_H
> +
> +/* Compare with cpu_set_upcall() in riscv/riscv/vm_machdep.c */
> +static inline void target_thread_set_upcall(CPURISCVState *regs,
> +    abi_ulong entry, abi_ulong arg, abi_ulong stack_base,
> +    abi_ulong stack_size)
> +{
> +    abi_ulong sp;
> +
> +    sp = (abi_ulong)(stack_base + stack_size) & ~(16 - 1);

ROUND_DOWN(stack_base + stack_size, 16)

r~

[PATCH v2 10/17] bsd-user: Define RISC-V VM parameters and helper functions

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Added definitions for RISC-V VM parameters, including maximum and
default sizes for text, data, and stack, as well as address space
limits.
Implemented helper functions for retrieving and setting specific
values in the CPU state, such as stack pointer and return values.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/target_arch_vmparam.h | 53 ++++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)
 create mode 100644 bsd-user/riscv/target_arch_vmparam.h

diff --git a/bsd-user/riscv/target_arch_vmparam.h b/bsd-user/riscv/target_arch_vmparam.h
new file mode 100644
index 0000000000..0f2486def1
--- /dev/null
+++ b/bsd-user/riscv/target_arch_vmparam.h
@@ -0,0 +1,53 @@
+/*
+ *  RISC-V VM parameters definitions
+ *
+ *  Copyright (c) 2019 Mark Corbin
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef TARGET_ARCH_VMPARAM_H
+#define TARGET_ARCH_VMPARAM_H
+
+#include "cpu.h"
+
+/* Compare with riscv/include/vmparam.h */
+#define TARGET_MAXTSIZ      (1 * GiB)           /* max text size */
+#define TARGET_DFLDSIZ      (128 * MiB)         /* initial data size limit */
+#define TARGET_MAXDSIZ      (1 * GiB)           /* max data size */
+#define TARGET_DFLSSIZ      (128 * MiB)         /* initial stack size limit */
+#define TARGET_MAXSSIZ      (1 * GiB)           /* max stack size */
+#define TARGET_SGROWSIZ     (128 * KiB)         /* amount to grow stack */
+
+#define TARGET_VM_MINUSER_ADDRESS   (0x0000000000000000UL)
+#define TARGET_VM_MAXUSER_ADDRESS   (0x0000004000000000UL)
+
+#define TARGET_USRSTACK (TARGET_VM_MAXUSER_ADDRESS - TARGET_PAGE_SIZE)
+
+static inline abi_ulong get_sp_from_cpustate(CPURISCVState *state)
+{
+    return state->gpr[xSP];
+}
+
+static inline void set_second_rval(CPURISCVState *state, abi_ulong retval2)
+{
+    state->gpr[xA1] = retval2;
+}
+
+static inline abi_ulong get_second_rval(CPURISCVState *state)
+{
+    return state->gpr[xA1];
+}
+
+#endif /* TARGET_ARCH_VMPARAM_H */
-- 
2.34.1

[PATCH v2 11/17] bsd-user: Define RISC-V system call structures and constants

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Introduced definitions for the RISC-V system call interface, including
the 'target_pt_regs' structure that outlines the register storage
layout during a system call.
Added constants for hardware machine identifiers.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Co-authored-by: Jessica Clarke <jrtc27@jrtc27.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/target_syscall.h | 38 +++++++++++++++++++++++++++++++++
 1 file changed, 38 insertions(+)
 create mode 100644 bsd-user/riscv/target_syscall.h

diff --git a/bsd-user/riscv/target_syscall.h b/bsd-user/riscv/target_syscall.h
new file mode 100644
index 0000000000..e7e5231309
--- /dev/null
+++ b/bsd-user/riscv/target_syscall.h
@@ -0,0 +1,38 @@
+/*
+ *  RISC-V system call definitions
+ *
+ *  Copyright (c) Mark Corbin
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef BSD_USER_RISCV_TARGET_SYSCALL_H
+#define BSD_USER_RISCV_TARGET_SYSCALL_H
+
+/*
+ * struct target_pt_regs defines the way the registers are stored on the stack
+ * during a system call.
+ */
+
+struct target_pt_regs {
+    abi_ulong regs[32];
+    abi_ulong sepc;
+};
+
+#define UNAME_MACHINE "riscv64"
+
+#define TARGET_HW_MACHINE       "riscv"
+#define TARGET_HW_MACHINE_ARCH  UNAME_MACHINE
+
+#endif /* BSD_USER_RISCV_TARGET_SYSCALL_H */
-- 
2.34.1

[PATCH v2 12/17] bsd-user: Add generic RISC-V64 target definitions

[Ajeet Singh]

From: Warner Losh <imp@bsdimp.com>

Added a generic definition for RISC-V64 target-specific details.
Implemented the 'regpairs_aligned' function,which returns 'false'
to indicate that register pairs are not aligned in the RISC-V64 ABI.

Signed-off-by: Warner Losh <imp@bsdimp.com>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/target.h | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)
 create mode 100644 bsd-user/riscv/target.h

diff --git a/bsd-user/riscv/target.h b/bsd-user/riscv/target.h
new file mode 100644
index 0000000000..036ddd185e
--- /dev/null
+++ b/bsd-user/riscv/target.h
@@ -0,0 +1,20 @@
+/*
+ * Riscv64 general target stuff that's common to all aarch details
+ *
+ * Copyright (c) 2022 M. Warner Losh <imp@bsdimp.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0-or-later
+ */
+
+#ifndef TARGET_H
+#define TARGET_H
+
+/*
+ * riscv64 ABI does not 'lump' the registers for 64-bit args.
+ */
+static inline bool regpairs_aligned(void *cpu_env)
+{
+    return false;
+}
+
+#endif /* TARGET_H */
-- 
2.34.1

[PATCH v2 13/17] bsd-user: Define RISC-V signal handling structures and constants

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Added definitions for RISC-V signal handling, including structures
and constants for managing signal frames and context

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Co-authored-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/target_arch_signal.h | 75 +++++++++++++++++++++++++++++
 1 file changed, 75 insertions(+)
 create mode 100644 bsd-user/riscv/target_arch_signal.h

diff --git a/bsd-user/riscv/target_arch_signal.h b/bsd-user/riscv/target_arch_signal.h
new file mode 100644
index 0000000000..1a634b865b
--- /dev/null
+++ b/bsd-user/riscv/target_arch_signal.h
@@ -0,0 +1,75 @@
+/*
+ *  RISC-V signal definitions
+ *
+ *  Copyright (c) 2019 Mark Corbin
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+
+#ifndef TARGET_ARCH_SIGNAL_H
+#define TARGET_ARCH_SIGNAL_H
+
+#include "cpu.h"
+
+
+#define TARGET_INSN_SIZE     4  /* riscv instruction size */
+
+/* Size of the signal trampoline code placed on the stack. */
+#define TARGET_SZSIGCODE    ((abi_ulong)(7 * TARGET_INSN_SIZE))
+
+/* Compare with riscv/include/_limits.h */
+#define TARGET_MINSIGSTKSZ  (1024 * 4)
+#define TARGET_SIGSTKSZ     (TARGET_MINSIGSTKSZ + 32768)
+
+struct target_gpregs {
+    uint64_t    gp_ra;
+    uint64_t    gp_sp;
+    uint64_t    gp_gp;
+    uint64_t    gp_tp;
+    uint64_t    gp_t[7];
+    uint64_t    gp_s[12];
+    uint64_t    gp_a[8];
+    uint64_t    gp_sepc;
+    uint64_t    gp_sstatus;
+};
+
+struct target_fpregs {
+    uint64_t        fp_x[32][2];
+    uint64_t        fp_fcsr;
+    uint32_t        fp_flags;
+    uint32_t        pad;
+};
+
+typedef struct target_mcontext {
+    struct target_gpregs   mc_gpregs;
+    struct target_fpregs   mc_fpregs;
+    uint32_t               mc_flags;
+#define TARGET_MC_FP_VALID 0x01
+    uint32_t               mc_pad;
+    uint64_t               mc_spare[8];
+} target_mcontext_t;
+
+#define TARGET_MCONTEXT_SIZE 864
+#define TARGET_UCONTEXT_SIZE 936
+
+#include "target_os_ucontext.h"
+
+struct target_sigframe {
+    target_ucontext_t   sf_uc; /* = *sf_uncontext */
+    target_siginfo_t    sf_si; /* = *sf_siginfo (SA_SIGINFO case)*/
+};
+
+#define TARGET_SIGSTACK_ALIGN 16
+
+#endif /* TARGET_ARCH_SIGNAL_H */
-- 
2.34.1

[PATCH v2 14/17] bsd-user: Implement RISC-V signal trampoline setup functions

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Added functions for setting up the RISC-V signal trampoline and signal
frame:

'set_sigtramp_args()': Configures the RISC-V CPU state with arguments
for the signal handler. It sets up the registers with the signal
number,pointers to the signal info and user context, the signal handler
address, and the signal frame pointer.

'setup_sigframe_arch()': Initializes the signal frame with the current
machine context.This function copies the context from the CPU state to
the signal frame, preparing it for the signal handler.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Signed-off-by: Warner Losh <imp@bsdimp.com>
Co-authored-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/signal.c | 63 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 63 insertions(+)
 create mode 100644 bsd-user/riscv/signal.c

diff --git a/bsd-user/riscv/signal.c b/bsd-user/riscv/signal.c
new file mode 100644
index 0000000000..2597fec2fd
--- /dev/null
+++ b/bsd-user/riscv/signal.c
@@ -0,0 +1,63 @@
+/*
+ *  RISC-V signal definitions
+ *
+ *  Copyright (c) 2019 Mark Corbin
+ *
+ *  This program is free software; you can redistribute it and/or modify
+ *  it under the terms of the GNU General Public License as published by
+ *  the Free Software Foundation; either version 2 of the License, or
+ *  (at your option) any later version.
+ *
+ *  This program is distributed in the hope that it will be useful,
+ *  but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *  GNU General Public License for more details.
+ *
+ *  You should have received a copy of the GNU General Public License
+ *  along with this program; if not, see <http://www.gnu.org/licenses/>.
+ */
+#include "qemu/osdep.h"
+
+#include "qemu.h"
+
+/*
+ * Compare with sendsig() in riscv/riscv/exec_machdep.c
+ * Assumes that target stack frame memory is locked.
+ */
+abi_long
+set_sigtramp_args(CPURISCVState *regs, int sig, struct target_sigframe *frame,
+    abi_ulong frame_addr, struct target_sigaction *ka)
+{
+    /*
+     * Arguments to signal handler:
+     *  a0 (10) = signal number
+     *  a1 (11) = siginfo pointer
+     *  a2 (12) = ucontext pointer
+     *  pc      = signal pointer handler
+     *  sp (2)  = sigframe pointer
+     *  ra (1)  = sigtramp at base of user stack
+     */
+
+     regs->gpr[xA0] = sig;
+     regs->gpr[xA1] = frame_addr +
+         offsetof(struct target_sigframe, sf_si);
+     regs->gpr[xA2] = frame_addr +
+         offsetof(struct target_sigframe, sf_uc);
+     regs->pc = ka->_sa_handler;
+     regs->gpr[xSP] = frame_addr;
+     regs->gpr[xRA] = TARGET_PS_STRINGS - TARGET_SZSIGCODE;
+     return 0;
+}
+
+/*
+ * Compare to riscv/riscv/exec_machdep.c sendsig()
+ * Assumes that the memory is locked if frame points to user memory.
+ */
+abi_long setup_sigframe_arch(CPURISCVState *env, abi_ulong frame_addr,
+                             struct target_sigframe *frame, int flags)
+{
+    target_mcontext_t *mcp = &frame->sf_uc.uc_mcontext;
+
+    get_mcontext(env, mcp, flags);
+    return 0;
+}
-- 
2.34.1

[PATCH v2 15/17] bsd-user: Implement 'get_mcontext' for RISC-V

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Added the 'get_mcontext' function to extract and populate
the RISC-V machine context from the CPU state.
This function is used to gather the current state of the
general-purpose registers and store it in a 'target_mcontext_'
structure.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Signed-off-by: Warner Losh <imp@bsdimp.com>
Co-authored-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/signal.c | 53 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 53 insertions(+)

diff --git a/bsd-user/riscv/signal.c b/bsd-user/riscv/signal.c
index 2597fec2fd..072ad821d2 100644
--- a/bsd-user/riscv/signal.c
+++ b/bsd-user/riscv/signal.c
@@ -61,3 +61,56 @@ abi_long setup_sigframe_arch(CPURISCVState *env, abi_ulong frame_addr,
     get_mcontext(env, mcp, flags);
     return 0;
 }
+
+/*
+ * Compare with get_mcontext() in riscv/riscv/machdep.c
+ * Assumes that the memory is locked if mcp points to user memory.
+ */
+abi_long get_mcontext(CPURISCVState *regs, target_mcontext_t *mcp,
+        int flags)
+{
+
+    mcp->mc_gpregs.gp_t[0] = tswap64(regs->gpr[5]);
+    mcp->mc_gpregs.gp_t[1] = tswap64(regs->gpr[6]);
+    mcp->mc_gpregs.gp_t[2] = tswap64(regs->gpr[7]);
+    mcp->mc_gpregs.gp_t[3] = tswap64(regs->gpr[28]);
+    mcp->mc_gpregs.gp_t[4] = tswap64(regs->gpr[29]);
+    mcp->mc_gpregs.gp_t[5] = tswap64(regs->gpr[30]);
+    mcp->mc_gpregs.gp_t[6] = tswap64(regs->gpr[31]);
+
+    mcp->mc_gpregs.gp_s[0] = tswap64(regs->gpr[8]);
+    mcp->mc_gpregs.gp_s[1] = tswap64(regs->gpr[9]);
+    mcp->mc_gpregs.gp_s[2] = tswap64(regs->gpr[18]);
+    mcp->mc_gpregs.gp_s[3] = tswap64(regs->gpr[19]);
+    mcp->mc_gpregs.gp_s[4] = tswap64(regs->gpr[20]);
+    mcp->mc_gpregs.gp_s[5] = tswap64(regs->gpr[21]);
+    mcp->mc_gpregs.gp_s[6] = tswap64(regs->gpr[22]);
+    mcp->mc_gpregs.gp_s[7] = tswap64(regs->gpr[23]);
+    mcp->mc_gpregs.gp_s[8] = tswap64(regs->gpr[24]);
+    mcp->mc_gpregs.gp_s[9] = tswap64(regs->gpr[25]);
+    mcp->mc_gpregs.gp_s[10] = tswap64(regs->gpr[26]);
+    mcp->mc_gpregs.gp_s[11] = tswap64(regs->gpr[27]);
+
+    mcp->mc_gpregs.gp_a[0] = tswap64(regs->gpr[10]);
+    mcp->mc_gpregs.gp_a[1] = tswap64(regs->gpr[11]);
+    mcp->mc_gpregs.gp_a[2] = tswap64(regs->gpr[12]);
+    mcp->mc_gpregs.gp_a[3] = tswap64(regs->gpr[13]);
+    mcp->mc_gpregs.gp_a[4] = tswap64(regs->gpr[14]);
+    mcp->mc_gpregs.gp_a[5] = tswap64(regs->gpr[15]);
+    mcp->mc_gpregs.gp_a[6] = tswap64(regs->gpr[16]);
+    mcp->mc_gpregs.gp_a[7] = tswap64(regs->gpr[17]);
+
+    if (flags & TARGET_MC_GET_CLEAR_RET) {
+        mcp->mc_gpregs.gp_a[0] = 0; /* a0 */
+        mcp->mc_gpregs.gp_a[1] = 0; /* a1 */
+        mcp->mc_gpregs.gp_t[0] = 0; /* clear syscall error */
+    }
+
+    mcp->mc_gpregs.gp_ra = tswap64(regs->gpr[1]);
+    mcp->mc_gpregs.gp_sp = tswap64(regs->gpr[2]);
+    mcp->mc_gpregs.gp_gp = tswap64(regs->gpr[3]);
+    mcp->mc_gpregs.gp_tp = tswap64(regs->gpr[4]);
+    mcp->mc_gpregs.gp_sepc = tswap64(regs->pc);
+
+    return 0;
+}
-- 
2.34.1

[PATCH v2 16/17] bsd-user: Implement set_mcontext and get_ucontext_sigreturn for RISCV

[Ajeet Singh]

From: Mark Corbin <mark@dibsco.co.uk>

Added implementations for 'set_mcontext' and 'get_ucontext_sigreturn'
functions for RISC-V architecture,
Both functions ensure that the CPU state and user context are properly
managed.

Signed-off-by: Mark Corbin <mark@dibsco.co.uk>
Signed-off-by: Warner Losh <imp@bsdimp.com>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Co-authored-by: Warner Losh <imp@bsdimp.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 bsd-user/riscv/signal.c | 54 +++++++++++++++++++++++++++++++++++++++++
 1 file changed, 54 insertions(+)

diff --git a/bsd-user/riscv/signal.c b/bsd-user/riscv/signal.c
index 072ad821d2..10c940cd49 100644
--- a/bsd-user/riscv/signal.c
+++ b/bsd-user/riscv/signal.c
@@ -114,3 +114,57 @@ abi_long get_mcontext(CPURISCVState *regs, target_mcontext_t *mcp,
 
     return 0;
 }
+
+/* Compare with set_mcontext() in riscv/riscv/exec_machdep.c */
+abi_long set_mcontext(CPURISCVState *regs, target_mcontext_t *mcp,
+        int srflag)
+{
+
+    regs->gpr[5] = tswap64(mcp->mc_gpregs.gp_t[0]);
+    regs->gpr[6] = tswap64(mcp->mc_gpregs.gp_t[1]);
+    regs->gpr[7] = tswap64(mcp->mc_gpregs.gp_t[2]);
+    regs->gpr[28] = tswap64(mcp->mc_gpregs.gp_t[3]);
+    regs->gpr[29] = tswap64(mcp->mc_gpregs.gp_t[4]);
+    regs->gpr[30] = tswap64(mcp->mc_gpregs.gp_t[5]);
+    regs->gpr[31] = tswap64(mcp->mc_gpregs.gp_t[6]);
+
+    regs->gpr[8] = tswap64(mcp->mc_gpregs.gp_s[0]);
+    regs->gpr[9] = tswap64(mcp->mc_gpregs.gp_s[1]);
+    regs->gpr[18] = tswap64(mcp->mc_gpregs.gp_s[2]);
+    regs->gpr[19] = tswap64(mcp->mc_gpregs.gp_s[3]);
+    regs->gpr[20] = tswap64(mcp->mc_gpregs.gp_s[4]);
+    regs->gpr[21] = tswap64(mcp->mc_gpregs.gp_s[5]);
+    regs->gpr[22] = tswap64(mcp->mc_gpregs.gp_s[6]);
+    regs->gpr[23] = tswap64(mcp->mc_gpregs.gp_s[7]);
+    regs->gpr[24] = tswap64(mcp->mc_gpregs.gp_s[8]);
+    regs->gpr[25] = tswap64(mcp->mc_gpregs.gp_s[9]);
+    regs->gpr[26] = tswap64(mcp->mc_gpregs.gp_s[10]);
+    regs->gpr[27] = tswap64(mcp->mc_gpregs.gp_s[11]);
+
+    regs->gpr[10] = tswap64(mcp->mc_gpregs.gp_a[0]);
+    regs->gpr[11] = tswap64(mcp->mc_gpregs.gp_a[1]);
+    regs->gpr[12] = tswap64(mcp->mc_gpregs.gp_a[2]);
+    regs->gpr[13] = tswap64(mcp->mc_gpregs.gp_a[3]);
+    regs->gpr[14] = tswap64(mcp->mc_gpregs.gp_a[4]);
+    regs->gpr[15] = tswap64(mcp->mc_gpregs.gp_a[5]);
+    regs->gpr[16] = tswap64(mcp->mc_gpregs.gp_a[6]);
+    regs->gpr[17] = tswap64(mcp->mc_gpregs.gp_a[7]);
+
+
+    regs->gpr[1] = tswap64(mcp->mc_gpregs.gp_ra);
+    regs->gpr[2] = tswap64(mcp->mc_gpregs.gp_sp);
+    regs->gpr[3] = tswap64(mcp->mc_gpregs.gp_gp);
+    regs->gpr[4] = tswap64(mcp->mc_gpregs.gp_tp);
+    regs->pc = tswap64(mcp->mc_gpregs.gp_sepc);
+
+    return 0;
+}
+
+/* Compare with sys_sigreturn() in riscv/riscv/machdep.c */
+abi_long get_ucontext_sigreturn(CPURISCVState *regs,
+                        abi_ulong target_sf, abi_ulong *target_uc)
+{
+
+    *target_uc = target_sf;
+    return 0;
+}
-- 
2.34.1

[PATCH v2 17/17] bsd-user: Add RISC-V 64-bit Target Configuration and Debug XML Files

[Ajeet Singh]

From: Warner Losh <imp@bsdimp.com>

Added configuration for RISC-V 64-bit target to the build system.

Signed-off-by: Warner Losh <imp@bsdimp.com>
Signed-off-by: Ajeet Singh <itachis@FreeBSD.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 configs/targets/riscv64-bsd-user.mak | 4 ++++
 1 file changed, 4 insertions(+)
 create mode 100644 configs/targets/riscv64-bsd-user.mak

diff --git a/configs/targets/riscv64-bsd-user.mak b/configs/targets/riscv64-bsd-user.mak
new file mode 100644
index 0000000000..191c2c483f
--- /dev/null
+++ b/configs/targets/riscv64-bsd-user.mak
@@ -0,0 +1,4 @@
+TARGET_ARCH=riscv64
+TARGET_BASE_ARCH=riscv
+TARGET_ABI_DIR=riscv
+TARGET_XML_FILES= gdb-xml/riscv-64bit-cpu.xml gdb-xml/riscv-32bit-fpu.xml gdb-xml/riscv-64bit-fpu.xml gdb-xml/riscv-64bit-virtual.xml
-- 
2.34.1