[PULL 07/32] hw/arm/xlnx-zynqmp: Use &error_abort for programming errors

["Philippe Mathieu-Daudé" <philmd@linaro.org>]

When a property value is static (not provided by QMP or CLI),
error shouldn't happen, otherwise it is a programming error.
Therefore simplify and use &error_abort as this can't fail.

Reported-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Anton Johansson <anjo@rev.ng>
Message-Id: <20241108154317.12129-11-philmd@linaro.org>
---
 hw/arm/xlnx-zynqmp.c | 38 ++++++++++++--------------------------
 1 file changed, 12 insertions(+), 26 deletions(-)

diff --git a/hw/arm/xlnx-zynqmp.c b/hw/arm/xlnx-zynqmp.c
index bd5b0dd5e76..d6022ff2d3d 100644
--- a/hw/arm/xlnx-zynqmp.c
+++ b/hw/arm/xlnx-zynqmp.c
@@ -689,16 +689,10 @@ static void xlnx_zynqmp_realize(DeviceState *dev, Error **errp)
          * - SDIO Specification Version 3.0
          * - eMMC Specification Version 4.51
          */
-        if (!object_property_set_uint(sdhci, "sd-spec-version", 3, errp)) {
-            return;
-        }
-        if (!object_property_set_uint(sdhci, "capareg", SDHCI_CAPABILITIES,
-                                      errp)) {
-            return;
-        }
-        if (!object_property_set_uint(sdhci, "uhs", UHS_I, errp)) {
-            return;
-        }
+        object_property_set_uint(sdhci, "sd-spec-version", 3, &error_abort);
+        object_property_set_uint(sdhci, "capareg", SDHCI_CAPABILITIES,
+                                 &error_abort);
+        object_property_set_uint(sdhci, "uhs", UHS_I, &error_abort);
         if (!sysbus_realize(SYS_BUS_DEVICE(sdhci), errp)) {
             return;
         }
@@ -763,14 +757,10 @@ static void xlnx_zynqmp_realize(DeviceState *dev, Error **errp)
     xlnx_zynqmp_create_unimp_mmio(s);
 
     for (i = 0; i < XLNX_ZYNQMP_NUM_GDMA_CH; i++) {
-        if (!object_property_set_uint(OBJECT(&s->gdma[i]), "bus-width", 128,
-                                      errp)) {
-            return;
-        }
-        if (!object_property_set_link(OBJECT(&s->gdma[i]), "dma",
-                                      OBJECT(system_memory), errp)) {
-            return;
-        }
+        object_property_set_uint(OBJECT(&s->gdma[i]), "bus-width", 128,
+                                 &error_abort);
+        object_property_set_link(OBJECT(&s->gdma[i]), "dma",
+                                 OBJECT(system_memory), &error_abort);
         if (!sysbus_realize(SYS_BUS_DEVICE(&s->gdma[i]), errp)) {
             return;
         }
@@ -811,10 +801,8 @@ static void xlnx_zynqmp_realize(DeviceState *dev, Error **errp)
     sysbus_connect_irq(SYS_BUS_DEVICE(&s->qspi_dma), 0,
                        qdev_get_gpio_in(DEVICE(&s->qspi_irq_orgate), 0));
 
-    if (!object_property_set_link(OBJECT(&s->qspi), "stream-connected-dma",
-                                  OBJECT(&s->qspi_dma), errp)) {
-         return;
-    }
+    object_property_set_link(OBJECT(&s->qspi), "stream-connected-dma",
+                             OBJECT(&s->qspi_dma), &error_abort);
     if (!sysbus_realize(SYS_BUS_DEVICE(&s->qspi), errp)) {
         return;
     }
@@ -833,10 +821,8 @@ static void xlnx_zynqmp_realize(DeviceState *dev, Error **errp)
     }
 
     for (i = 0; i < XLNX_ZYNQMP_NUM_USB; i++) {
-        if (!object_property_set_link(OBJECT(&s->usb[i].sysbus_xhci), "dma",
-                                      OBJECT(system_memory), errp)) {
-            return;
-        }
+        object_property_set_link(OBJECT(&s->usb[i].sysbus_xhci), "dma",
+                                 OBJECT(system_memory), &error_abort);
 
         qdev_prop_set_uint32(DEVICE(&s->usb[i].sysbus_xhci), "intrs", 4);
         qdev_prop_set_uint32(DEVICE(&s->usb[i].sysbus_xhci), "slots", 2);
-- 
2.47.1