[PULL 01/14] hw/sd/sdhci: Set reset value of interrupt registers

["Philippe Mathieu-Daudé" <philmd@linaro.org>]

From: BALATON Zoltan <balaton@eik.bme.hu>

The interrupt enable registers are not reset to 0 on Freescale eSDHC
but some bits are enabled on reset. At least some U-Boot versions seem
to expect this and not initialise these registers before expecting
interrupts. Use existing vendor property for Freescale eSDHC and set
the reset value of the interrupt registers to match Freescale
documentation.

Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-ID: <20250210160329.DDA7F4E600E@zero.eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
---
 include/hw/sd/sdhci.h | 1 +
 hw/ppc/e500.c         | 1 +
 hw/sd/sdhci.c         | 4 ++++
 3 files changed, 6 insertions(+)

diff --git a/include/hw/sd/sdhci.h b/include/hw/sd/sdhci.h
index 38c08e28598..f722d8eb1cc 100644
--- a/include/hw/sd/sdhci.h
+++ b/include/hw/sd/sdhci.h
@@ -110,6 +110,7 @@ typedef struct SDHCIState SDHCIState;
 
 #define SDHCI_VENDOR_NONE       0
 #define SDHCI_VENDOR_IMX        1
+#define SDHCI_VENDOR_FSL        2
 
 /*
  * Controller does not provide transfer-complete interrupt when not
diff --git a/hw/ppc/e500.c b/hw/ppc/e500.c
index fe8b9f79621..69269aa24c4 100644
--- a/hw/ppc/e500.c
+++ b/hw/ppc/e500.c
@@ -1043,6 +1043,7 @@ void ppce500_init(MachineState *machine)
         dev = qdev_new(TYPE_SYSBUS_SDHCI);
         qdev_prop_set_uint8(dev, "sd-spec-version", 2);
         qdev_prop_set_uint8(dev, "endianness", DEVICE_BIG_ENDIAN);
+        qdev_prop_set_uint8(dev, "vendor", SDHCI_VENDOR_FSL);
         s = SYS_BUS_DEVICE(dev);
         sysbus_realize_and_unref(s, &error_fatal);
         sysbus_connect_irq(s, 0, qdev_get_gpio_in(mpicdev, MPC85XX_ESDHC_IRQ));
diff --git a/hw/sd/sdhci.c b/hw/sd/sdhci.c
index 1f45a77566c..fe87e18d5d2 100644
--- a/hw/sd/sdhci.c
+++ b/hw/sd/sdhci.c
@@ -307,6 +307,10 @@ static void sdhci_reset(SDHCIState *s)
     s->data_count = 0;
     s->stopped_state = sdhc_not_stopped;
     s->pending_insert_state = false;
+    if (s->vendor == SDHCI_VENDOR_FSL) {
+        s->norintstsen = 0x013f;
+        s->errintstsen = 0x117f;
+    }
 }
 
 static void sdhci_poweron_reset(DeviceState *dev)
-- 
2.47.1