Re: [QEMU PATCH v4 10/10] cxl-mailbox-utils: 0x5605 - FMAPI Initiate DC Release

[Jonathan Cameron via <qemu-devel@nongnu.org>]

On Thu, 26 Jun 2025 22:23:33 +0000
anisa.su887@gmail.com wrote:

> From: Anisa Su <anisa.su@samsung.com>
> 
> FM DCD Management command 0x5605 implemented per CXL r3.2 Spec Section 7.6.7.6.6
> 
> Signed-off-by: Anisa Su <anisa.su@samsung.com>
A few more long line related tweaks.

> ---
>  hw/cxl/cxl-mailbox-utils.c | 79 ++++++++++++++++++++++++++++++++++++++
>  1 file changed, 79 insertions(+)
> 
> diff --git a/hw/cxl/cxl-mailbox-utils.c b/hw/cxl/cxl-mailbox-utils.c
> index 787eeaa7b9..87f9535d46 100644
> --- a/hw/cxl/cxl-mailbox-utils.c
> +++ b/hw/cxl/cxl-mailbox-utils.c
> @@ -123,6 +123,7 @@ enum {
>          #define SET_DC_REGION_CONFIG        0x2
>          #define GET_DC_REGION_EXTENT_LIST   0x3
>          #define INITIATE_DC_ADD             0x4
> +        #define INITIATE_DC_RELEASE         0x5
>  };
>  
>  /* CCI Message Format CXL r3.1 Figure 7-19 */
> @@ -3638,6 +3639,77 @@ static CXLRetCode cmd_fm_initiate_dc_add(const struct cxl_cmd *cmd,
>      }
>  }
>  
> +#define CXL_EXTENT_REMOVAL_POLICY_MASK 0x0F
> +#define CXL_FORCED_REMOVAL_MASK (1 << 4)
> +/* CXL r3.2 Section 7.6.7.6.6 Initiate Dynamic Capacity Release (Opcode 5605h) */

Added a colon and wrapped after the number.

> +static CXLRetCode cmd_fm_initiate_dc_release(const struct cxl_cmd *cmd,
> +                                             uint8_t *payload_in,
> +                                             size_t len_in,
> +                                             uint8_t *payload_out,
> +                                             size_t *len_out,
> +                                             CXLCCI *cci)
> +{
> +    struct {
> +        uint16_t host_id;
> +        uint8_t flags;
> +        uint8_t reg_num;
> +        uint64_t length;
> +        uint8_t tag[0x10];
> +        uint32_t ext_count;
> +        CXLDCExtentRaw extents[];
> +    } QEMU_PACKED *in = (void *)payload_in;
> +    CXLType3Dev *ct3d = CXL_TYPE3(cci->d);
> +    int i, rc;
> +
> +    switch (in->flags & CXL_EXTENT_REMOVAL_POLICY_MASK) {
> +        case CXL_EXTENT_REMOVAL_POLICY_PRESCRIPTIVE: {
> +            CXLDCExtentList updated_list;
> +            uint32_t updated_list_size;
> +            g_autofree CXLUpdateDCExtentListInPl *list =
> +                g_malloc0(sizeof(*list) +
> +                    in->ext_count * sizeof(*list->updated_entries));
> +
> +            convert_raw_extents(in->extents, list, in->ext_count);
> +            rc = cxl_detect_malformed_extent_list(ct3d, list);
> +            if (rc) {
> +                return rc;
> +            }
> +
> +            /* Fail with Invalid PA if an extent is pending and Forced Removal

/*
 * Fail...

> +             * flag not set
> +             */
> +            if (!(in->flags & CXL_FORCED_REMOVAL_MASK)) {
> +                for (i = 0; i < in->ext_count; i++) {
> +                    CXLDCExtentRaw ext = in->extents[i];
> +                    /* Check requested extents don't overlap with pending extents. */
Made this a multiline comment. 

> +                    if (cxl_extent_groups_overlaps_dpa_range(&ct3d->dc.extents_pending,
This is quite a bit too far over so I just went with the ugly
                    if (cxl_extent_groups_overlaps_dpa_range(
                            &ct3d->dc.extents_pending,

> +                                                             ext.start_dpa, ext.len)) {
> +                        return CXL_MBOX_INVALID_PA;