Re: [Qemu-devel] [PATCH 1/2] hw/hppa: Use qemu_log_mask instead of fprintf to stderr

["Alex Bennée" <alex.bennee@linaro.org>]

Richard Henderson <richard.henderson@linaro.org> writes:

> Reported-by: Thomas Huth <thuth@redhat.com>
> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>

Reviewed-by: Alex Bennée <alex.bennee@linaro.org>

> ---
>  hw/hppa/machine.c | 17 ++++++++---------
>  1 file changed, 8 insertions(+), 9 deletions(-)
>
> diff --git a/hw/hppa/machine.c b/hw/hppa/machine.c
> index afd3867313..19033e268d 100644
> --- a/hw/hppa/machine.c
> +++ b/hw/hppa/machine.c
> @@ -19,6 +19,7 @@
>  #include "hw/hppa/hppa_sys.h"
>  #include "qemu/cutils.h"
>  #include "qapi/error.h"
> +#include "qemu/log.h"
>
>  #define MAX_IDE_BUS 2
>
> @@ -111,7 +112,6 @@ static void machine_hppa_init(MachineState *machine)
>          uint32_t addr = DINO_UART_HPA + 0x800;
>          serial_mm_init(addr_space, addr, 0, serial_irq,
>                         115200, serial_hds[0], DEVICE_BIG_ENDIAN);
> -        fprintf(stderr, "Serial port created at 0x%x\n", addr);
>      }
>
>      /* SCSI disk setup. */
> @@ -146,9 +146,9 @@ static void machine_hppa_init(MachineState *machine)
>          error_report("could not load firmware '%s'", firmware_filename);
>          exit(1);
>      }
> -    fprintf(stderr, "Firmware loaded at 0x%08" PRIx64 "-0x%08" PRIx64
> -            ", entry at 0x%08" PRIx64 ".\n",
> -            firmware_low, firmware_high, firmware_entry);
> +    qemu_log_mask(CPU_LOG_PAGE, "Firmware loaded at 0x%08" PRIx64
> +                  "-0x%08" PRIx64 ", entry at 0x%08" PRIx64 ".\n",
> +                  firmware_low, firmware_high, firmware_entry);
>      if (firmware_low < ram_size || firmware_high >= FIRMWARE_END) {
>          error_report("Firmware overlaps with memory or IO space");
>          exit(1);
> @@ -163,7 +163,6 @@ static void machine_hppa_init(MachineState *machine)
>
>      /* Load kernel */
>      if (kernel_filename) {
> -        fprintf(stderr, "LOADING kernel '%s'\n", kernel_filename);
>          size = load_elf(kernel_filename, &cpu_hppa_to_phys,
>                          NULL, &kernel_entry, &kernel_low, &kernel_high,
>                          true, EM_PARISC, 0, 0);
> @@ -177,10 +176,10 @@ static void machine_hppa_init(MachineState *machine)
>              error_report("could not load kernel '%s'", kernel_filename);
>              exit(1);
>          }
> -
> -        fprintf(stderr, "Kernel loaded at 0x%08" PRIx64 "-0x%08" PRIx64
> -                ", entry at 0x%08" PRIx64 ", size %ld kB.\n",
> -                kernel_low, kernel_high, kernel_entry, size / 1024);
> +        qemu_log_mask(CPU_LOG_PAGE, "Kernel loaded at 0x%08" PRIx64
> +                      "-0x%08" PRIx64 ", entry at 0x%08" PRIx64
> +                      ", size %ld kB.\n",
> +                      kernel_low, kernel_high, kernel_entry, size / 1024);
>
>          if (kernel_cmdline) {
>              cpu[0]->env.gr[24] = 0x4000;


--
Alex Bennée