[PATCH v6 0/4] riscv: Add support for Zicbo[m,z,p] instructions

[PATCH v6 0/4] riscv: Add support for Zicbo[m,z,p] instructions

[Daniel Henrique Barboza]

Hi,

This new version contains a change in patch 2 based on Richard's
feedback in v5 [1].

Changes from v5:
- patch 2:
  - check if 'mem' is mapped into RAM with 'tlb_vaddr_to_host' before
    zeroing it.
- v5 link: https://lists.gnu.org/archive/html/qemu-devel/2023-02/msg04414.html

[1] https://lists.gnu.org/archive/html/qemu-devel/2023-02/msg04414.html

Christoph Muellner (4):
  accel/tcg: Add probe_access_range_flags interface
  target/riscv: implement Zicboz extension
  target/riscv: implement Zicbom extension
  target/riscv: add Zicbop cbo.prefetch{i,r,m} placeholder

 accel/tcg/cputlb.c                          |  19 +++
 accel/tcg/user-exec.c                       |  15 +-
 include/exec/exec-all.h                     |  24 +++
 target/riscv/cpu.c                          |   7 +
 target/riscv/cpu.h                          |   4 +
 target/riscv/helper.h                       |   5 +
 target/riscv/insn32.decode                  |  16 +-
 target/riscv/insn_trans/trans_rvzicbo.c.inc |  57 +++++++
 target/riscv/op_helper.c                    | 162 ++++++++++++++++++++
 target/riscv/translate.c                    |   1 +
 10 files changed, 306 insertions(+), 4 deletions(-)
 create mode 100644 target/riscv/insn_trans/trans_rvzicbo.c.inc

-- 
2.39.2

[PATCH v6 1/4] accel/tcg: Add probe_access_range_flags interface

[Daniel Henrique Barboza]

From: Christoph Muellner <cmuellner@linux.com>

The existing probe_access* functions do not allow to specify the
access size and a non-faulting behavior at the same time.

This is resolved by adding a generalization of probe_access_flags()
that takes an additional size parameter.

The semantics is basically the same as probe_access_flags(),
but instead of assuming an access to any byte of the addressed
page, we can restrict to access to a specific area, like
probe_access() allows.

Signed-off-by: Christoph Muellner <cmuellner@linux.com>
---
 accel/tcg/cputlb.c      | 19 +++++++++++++++++++
 accel/tcg/user-exec.c   | 15 ++++++++++++---
 include/exec/exec-all.h | 24 ++++++++++++++++++++++++
 3 files changed, 55 insertions(+), 3 deletions(-)

diff --git a/accel/tcg/cputlb.c b/accel/tcg/cputlb.c
index 4812d83961..dd3bc7a356 100644
--- a/accel/tcg/cputlb.c
+++ b/accel/tcg/cputlb.c
@@ -1606,6 +1606,25 @@ int probe_access_full(CPUArchState *env, target_ulong addr,
     return flags;
 }
 
+int probe_access_range_flags(CPUArchState *env, target_ulong addr,
+                             int size, MMUAccessType access_type,
+                             int mmu_idx, bool nonfault, void **phost,
+                             uintptr_t retaddr)
+{
+    CPUTLBEntryFull *full;
+    int flags = probe_access_internal(env, addr, size, access_type,
+                                      mmu_idx, nonfault, phost, &full,
+                                      retaddr);
+
+    /* Handle clean RAM pages.  */
+    if (unlikely(flags & TLB_NOTDIRTY)) {
+        notdirty_write(env_cpu(env), addr, 1, full, retaddr);
+        flags &= ~TLB_NOTDIRTY;
+    }
+
+    return flags;
+}
+
 int probe_access_flags(CPUArchState *env, target_ulong addr,
                        MMUAccessType access_type, int mmu_idx,
                        bool nonfault, void **phost, uintptr_t retaddr)
diff --git a/accel/tcg/user-exec.c b/accel/tcg/user-exec.c
index ae67d84638..a73c840655 100644
--- a/accel/tcg/user-exec.c
+++ b/accel/tcg/user-exec.c
@@ -761,9 +761,10 @@ static int probe_access_internal(CPUArchState *env, target_ulong addr,
     cpu_loop_exit_sigsegv(env_cpu(env), addr, access_type, maperr, ra);
 }
 
-int probe_access_flags(CPUArchState *env, target_ulong addr,
-                       MMUAccessType access_type, int mmu_idx,
-                       bool nonfault, void **phost, uintptr_t ra)
+int probe_access_range_flags(CPUArchState *env, target_ulong addr,
+                             int size, MMUAccessType access_type,
+                             int mmu_idx, bool nonfault, void **phost,
+                             uintptr_t ra)
 {
     int flags;
 
@@ -772,6 +773,14 @@ int probe_access_flags(CPUArchState *env, target_ulong addr,
     return flags;
 }
 
+int probe_access_flags(CPUArchState *env, target_ulong addr,
+                       MMUAccessType access_type, int mmu_idx,
+                       bool nonfault, void **phost, uintptr_t ra)
+{
+    return probe_access_range_flags(env, addr, 0, access_type, mmu_idx,
+                                    nonfault, phost, ra);
+}
+
 void *probe_access(CPUArchState *env, target_ulong addr, int size,
                    MMUAccessType access_type, int mmu_idx, uintptr_t ra)
 {
diff --git a/include/exec/exec-all.h b/include/exec/exec-all.h
index 54585a9954..b75f15f247 100644
--- a/include/exec/exec-all.h
+++ b/include/exec/exec-all.h
@@ -442,6 +442,30 @@ static inline void *probe_read(CPUArchState *env, target_ulong addr, int size,
     return probe_access(env, addr, size, MMU_DATA_LOAD, mmu_idx, retaddr);
 }
 
+/**
+ * probe_access_range_flags:
+ * @env: CPUArchState
+ * @addr: guest virtual address to look up
+ * @size: size of the access
+ * @access_type: read, write or execute permission
+ * @mmu_idx: MMU index to use for lookup
+ * @nonfault: suppress the fault
+ * @phost: return value for host address
+ * @retaddr: return address for unwinding
+ *
+ * Similar to probe_access, loosely returning the TLB_FLAGS_MASK for
+ * the access range, and storing the host address for RAM in @phost.
+ *
+ * If @nonfault is set, do not raise an exception but return TLB_INVALID_MASK.
+ * Do not handle watchpoints, but include TLB_WATCHPOINT in the returned flags.
+ * Do handle clean pages, so exclude TLB_NOTDIRTY from the returned flags.
+ * For simplicity, all "mmio-like" flags are folded to TLB_MMIO.
+ */
+int probe_access_range_flags(CPUArchState *env, target_ulong addr,
+                             int size, MMUAccessType access_type,
+                             int mmu_idx, bool nonfault, void **phost,
+                             uintptr_t retaddr);
+
 /**
  * probe_access_flags:
  * @env: CPUArchState
-- 
2.39.2

[PATCH v6 2/4] target/riscv: implement Zicboz extension

[Daniel Henrique Barboza]

From: Christoph Muellner <cmuellner@linux.com>

The RISC-V base cache management operation (CBO) ISA extension has been
ratified. It defines three extensions: Cache-Block Management, Cache-Block
Prefetch and Cache-Block Zero. More information about the spec can be
found at [1].

Let's start by implementing the Cache-Block Zero extension, Zicboz. It
uses the cbo.zero instruction that, as with all CBO instructions that
will be added later, needs to be implemented in an overlap group with
the LQ instruction due to overlapping patterns.

cbo.zero throws a Illegal Instruction/Virtual Instruction exception
depending on CSR state. This is also the case for the remaining cbo
instructions we're going to add next, so create a check_zicbo_envcfg()
that will be used by all Zicbo[mz] instructions.

[1] https://github.com/riscv/riscv-CMOs/blob/master/specifications/cmobase-v1.0.1.pdf

Co-developed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Signed-off-by: Christoph Muellner <cmuellner@linux.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
---
 target/riscv/cpu.c                          |  4 ++
 target/riscv/cpu.h                          |  2 +
 target/riscv/helper.h                       |  3 ++
 target/riscv/insn32.decode                  | 10 +++-
 target/riscv/insn_trans/trans_rvzicbo.c.inc | 30 +++++++++++
 target/riscv/op_helper.c                    | 55 +++++++++++++++++++++
 target/riscv/translate.c                    |  1 +
 7 files changed, 104 insertions(+), 1 deletion(-)
 create mode 100644 target/riscv/insn_trans/trans_rvzicbo.c.inc

diff --git a/target/riscv/cpu.c b/target/riscv/cpu.c
index 93b52b826c..7dd37de7f9 100644
--- a/target/riscv/cpu.c
+++ b/target/riscv/cpu.c
@@ -74,6 +74,7 @@ struct isa_ext_data {
 static const struct isa_ext_data isa_edata_arr[] = {
     ISA_EXT_DATA_ENTRY(h, false, PRIV_VERSION_1_12_0, ext_h),
     ISA_EXT_DATA_ENTRY(v, false, PRIV_VERSION_1_10_0, ext_v),
+    ISA_EXT_DATA_ENTRY(zicboz, true, PRIV_VERSION_1_12_0, ext_icboz),
     ISA_EXT_DATA_ENTRY(zicsr, true, PRIV_VERSION_1_10_0, ext_icsr),
     ISA_EXT_DATA_ENTRY(zifencei, true, PRIV_VERSION_1_10_0, ext_ifencei),
     ISA_EXT_DATA_ENTRY(zihintpause, true, PRIV_VERSION_1_10_0, ext_zihintpause),
@@ -1126,6 +1127,9 @@ static Property riscv_cpu_extensions[] = {
     DEFINE_PROP_BOOL("zhinx", RISCVCPU, cfg.ext_zhinx, false),
     DEFINE_PROP_BOOL("zhinxmin", RISCVCPU, cfg.ext_zhinxmin, false),
 
+    DEFINE_PROP_BOOL("zicboz", RISCVCPU, cfg.ext_icboz, true),
+    DEFINE_PROP_UINT16("cboz_blocksize", RISCVCPU, cfg.cboz_blocksize, 64),
+
     DEFINE_PROP_BOOL("zmmul", RISCVCPU, cfg.ext_zmmul, false),
 
     /* Vendor-specific custom extensions */
diff --git a/target/riscv/cpu.h b/target/riscv/cpu.h
index 7128438d8e..6b4c714d3a 100644
--- a/target/riscv/cpu.h
+++ b/target/riscv/cpu.h
@@ -447,6 +447,7 @@ struct RISCVCPUConfig {
     bool ext_zkt;
     bool ext_ifencei;
     bool ext_icsr;
+    bool ext_icboz;
     bool ext_zihintpause;
     bool ext_smstateen;
     bool ext_sstc;
@@ -494,6 +495,7 @@ struct RISCVCPUConfig {
     char *vext_spec;
     uint16_t vlen;
     uint16_t elen;
+    uint16_t cboz_blocksize;
     bool mmu;
     bool pmp;
     bool epmp;
diff --git a/target/riscv/helper.h b/target/riscv/helper.h
index 0497370afd..ce165821b8 100644
--- a/target/riscv/helper.h
+++ b/target/riscv/helper.h
@@ -97,6 +97,9 @@ DEF_HELPER_FLAGS_2(fcvt_h_l, TCG_CALL_NO_RWG, i64, env, tl)
 DEF_HELPER_FLAGS_2(fcvt_h_lu, TCG_CALL_NO_RWG, i64, env, tl)
 DEF_HELPER_FLAGS_2(fclass_h, TCG_CALL_NO_RWG_SE, tl, env, i64)
 
+/* Cache-block operations */
+DEF_HELPER_2(cbo_zero, void, env, tl)
+
 /* Special functions */
 DEF_HELPER_2(csrr, tl, env, int)
 DEF_HELPER_3(csrw, void, env, int, tl)
diff --git a/target/riscv/insn32.decode b/target/riscv/insn32.decode
index b7e7613ea2..3985bc703f 100644
--- a/target/riscv/insn32.decode
+++ b/target/riscv/insn32.decode
@@ -179,7 +179,15 @@ sraw     0100000 .....  ..... 101 ..... 0111011 @r
 
 # *** RV128I Base Instruction Set (in addition to RV64I) ***
 ldu      ............   ..... 111 ..... 0000011 @i
-lq       ............   ..... 010 ..... 0001111 @i
+{
+  [
+    # *** RV32 Zicboz Standard Extension ***
+    cbo_zero   0000000 00100 ..... 010 00000 0001111 @sfence_vm
+  ]
+
+  # *** RVI128 lq ***
+  lq       ............   ..... 010 ..... 0001111 @i
+}
 sq       ............   ..... 100 ..... 0100011 @s
 addid    ............  .....  000 ..... 1011011 @i
 sllid    000000 ......  ..... 001 ..... 1011011 @sh6
diff --git a/target/riscv/insn_trans/trans_rvzicbo.c.inc b/target/riscv/insn_trans/trans_rvzicbo.c.inc
new file mode 100644
index 0000000000..feabc28342
--- /dev/null
+++ b/target/riscv/insn_trans/trans_rvzicbo.c.inc
@@ -0,0 +1,30 @@
+/*
+ * RISC-V translation routines for the RISC-V CBO Extension.
+ *
+ * Copyright (c) 2021 Philipp Tomsich, philipp.tomsich@vrull.eu
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2 or later, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#define REQUIRE_ZICBOZ(ctx) do {    \
+    if (!ctx->cfg_ptr->ext_icboz) { \
+        return false;               \
+    }                               \
+} while (0)
+
+static bool trans_cbo_zero(DisasContext *ctx, arg_cbo_zero *a)
+{
+    REQUIRE_ZICBOZ(ctx);
+    gen_helper_cbo_zero(cpu_env, cpu_gpr[a->rs1]);
+    return true;
+}
diff --git a/target/riscv/op_helper.c b/target/riscv/op_helper.c
index 48f918b71b..c5053e9446 100644
--- a/target/riscv/op_helper.c
+++ b/target/riscv/op_helper.c
@@ -3,6 +3,7 @@
  *
  * Copyright (c) 2016-2017 Sagar Karandikar, sagark@eecs.berkeley.edu
  * Copyright (c) 2017-2018 SiFive, Inc.
+ * Copyright (c) 2022      VRULL GmbH
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms and conditions of the GNU General Public License,
@@ -123,6 +124,60 @@ target_ulong helper_csrrw_i128(CPURISCVState *env, int csr,
     return int128_getlo(rv);
 }
 
+
+/*
+ * check_zicbo_envcfg
+ *
+ * Raise virtual exceptions and illegal instruction exceptions for
+ * Zicbo[mz] instructions based on the settings of [mhs]envcfg as
+ * specified in section 2.5.1 of the CMO specification.
+ */
+static void check_zicbo_envcfg(CPURISCVState *env, target_ulong envbits,
+                                uintptr_t ra)
+{
+#ifndef CONFIG_USER_ONLY
+    /*
+     * Check for virtual instruction exceptions first, as we don't see
+     * VU and VS reflected in env->priv (these are just the translated
+     * U and S stated with virtualisation enabled.
+     */
+    if (riscv_cpu_virt_enabled(env) &&
+        (((env->priv < PRV_H) && !get_field(env->henvcfg, envbits)) ||
+         ((env->priv < PRV_S) && !get_field(env->senvcfg, envbits)))) {
+        riscv_raise_exception(env, RISCV_EXCP_VIRT_INSTRUCTION_FAULT, ra);
+    }
+
+    if (((env->priv < PRV_M) && !get_field(env->menvcfg, envbits)) ||
+        ((env->priv < PRV_S) && !get_field(env->senvcfg, envbits))) {
+        riscv_raise_exception(env, RISCV_EXCP_ILLEGAL_INST, ra);
+    }
+#endif
+}
+
+void helper_cbo_zero(CPURISCVState *env, target_ulong address)
+{
+    RISCVCPU *cpu = env_archcpu(env);
+    uintptr_t ra = GETPC();
+    uint16_t cbozlen;
+    void *mem;
+
+    check_zicbo_envcfg(env, MENVCFG_CBZE, ra);
+
+    /* Get the size of the cache block for zero instructions. */
+    cbozlen = cpu->cfg.cboz_blocksize;
+
+    /* Mask off low-bits to align-down to the cache-block. */
+    address &= ~(cbozlen - 1);
+
+    mem = tlb_vaddr_to_host(env, address, MMU_DATA_STORE,
+                            cpu_mmu_index(env, false));
+
+    if (likely(mem)) {
+        /* Zero the block */
+        memset(mem, 0, cbozlen);
+    }
+}
+
 #ifndef CONFIG_USER_ONLY
 
 target_ulong helper_sret(CPURISCVState *env)
diff --git a/target/riscv/translate.c b/target/riscv/translate.c
index 772f9d7973..7f687a7e37 100644
--- a/target/riscv/translate.c
+++ b/target/riscv/translate.c
@@ -1104,6 +1104,7 @@ static uint32_t opcode_at(DisasContextBase *dcbase, target_ulong pc)
 #include "insn_trans/trans_rvv.c.inc"
 #include "insn_trans/trans_rvb.c.inc"
 #include "insn_trans/trans_rvzawrs.c.inc"
+#include "insn_trans/trans_rvzicbo.c.inc"
 #include "insn_trans/trans_rvzfh.c.inc"
 #include "insn_trans/trans_rvk.c.inc"
 #include "insn_trans/trans_privileged.c.inc"
-- 
2.39.2

[PATCH v6 3/4] target/riscv: implement Zicbom extension

[Daniel Henrique Barboza]

From: Christoph Muellner <cmuellner@linux.com>

Zicbom is the Cache-Block Management extension defined in the already
ratified RISC-V Base Cache Management Operation (CBO) ISA extension [1].

The extension contains three instructions: cbo.clean, cbo.flush and
cbo.inval. All of them must be implemented in the same group as LQ and
cbo.zero due to overlapping patterns.

All these instructions can throw a Illegal Instruction/Virtual
Instruction exception, similar to the existing cbo.zero. The same
check_zicbo_envcfg() is used to handle these exceptions.

Aside from that, these instructions also need to handle page faults and
guest page faults. This is done in a new check_zicbom_access() helper.

As with Zicboz, the cache block size for Zicbom is also configurable.
Note that the spec determines that Zicbo[mp] and Zicboz can have
different cache sizes (Section 2.7 of [1]), so we also include a
'cbom_blocksize' to go along with the existing 'cboz_blocksize'. They
are set to the same size, so unless users want to play around with the
settings both sizes will be the same.

[1] https://github.com/riscv/riscv-CMOs/blob/master/specifications/cmobase-v1.0.1.pdf

Co-developed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Signed-off-by: Christoph Muellner <cmuellner@linux.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
---
 target/riscv/cpu.c                          |   3 +
 target/riscv/cpu.h                          |   2 +
 target/riscv/helper.h                       |   2 +
 target/riscv/insn32.decode                  |   5 +
 target/riscv/insn_trans/trans_rvzicbo.c.inc |  27 +++++
 target/riscv/op_helper.c                    | 107 ++++++++++++++++++++
 6 files changed, 146 insertions(+)

diff --git a/target/riscv/cpu.c b/target/riscv/cpu.c
index 7dd37de7f9..4b779b1775 100644
--- a/target/riscv/cpu.c
+++ b/target/riscv/cpu.c
@@ -74,6 +74,7 @@ struct isa_ext_data {
 static const struct isa_ext_data isa_edata_arr[] = {
     ISA_EXT_DATA_ENTRY(h, false, PRIV_VERSION_1_12_0, ext_h),
     ISA_EXT_DATA_ENTRY(v, false, PRIV_VERSION_1_10_0, ext_v),
+    ISA_EXT_DATA_ENTRY(zicbom, true, PRIV_VERSION_1_12_0, ext_icbom),
     ISA_EXT_DATA_ENTRY(zicboz, true, PRIV_VERSION_1_12_0, ext_icboz),
     ISA_EXT_DATA_ENTRY(zicsr, true, PRIV_VERSION_1_10_0, ext_icsr),
     ISA_EXT_DATA_ENTRY(zifencei, true, PRIV_VERSION_1_10_0, ext_ifencei),
@@ -1127,6 +1128,8 @@ static Property riscv_cpu_extensions[] = {
     DEFINE_PROP_BOOL("zhinx", RISCVCPU, cfg.ext_zhinx, false),
     DEFINE_PROP_BOOL("zhinxmin", RISCVCPU, cfg.ext_zhinxmin, false),
 
+    DEFINE_PROP_BOOL("zicbom", RISCVCPU, cfg.ext_icbom, true),
+    DEFINE_PROP_UINT16("cbom_blocksize", RISCVCPU, cfg.cbom_blocksize, 64),
     DEFINE_PROP_BOOL("zicboz", RISCVCPU, cfg.ext_icboz, true),
     DEFINE_PROP_UINT16("cboz_blocksize", RISCVCPU, cfg.cboz_blocksize, 64),
 
diff --git a/target/riscv/cpu.h b/target/riscv/cpu.h
index 6b4c714d3a..a0673b4604 100644
--- a/target/riscv/cpu.h
+++ b/target/riscv/cpu.h
@@ -447,6 +447,7 @@ struct RISCVCPUConfig {
     bool ext_zkt;
     bool ext_ifencei;
     bool ext_icsr;
+    bool ext_icbom;
     bool ext_icboz;
     bool ext_zihintpause;
     bool ext_smstateen;
@@ -495,6 +496,7 @@ struct RISCVCPUConfig {
     char *vext_spec;
     uint16_t vlen;
     uint16_t elen;
+    uint16_t cbom_blocksize;
     uint16_t cboz_blocksize;
     bool mmu;
     bool pmp;
diff --git a/target/riscv/helper.h b/target/riscv/helper.h
index ce165821b8..37b54e0991 100644
--- a/target/riscv/helper.h
+++ b/target/riscv/helper.h
@@ -98,6 +98,8 @@ DEF_HELPER_FLAGS_2(fcvt_h_lu, TCG_CALL_NO_RWG, i64, env, tl)
 DEF_HELPER_FLAGS_2(fclass_h, TCG_CALL_NO_RWG_SE, tl, env, i64)
 
 /* Cache-block operations */
+DEF_HELPER_2(cbo_clean_flush, void, env, tl)
+DEF_HELPER_2(cbo_inval, void, env, tl)
 DEF_HELPER_2(cbo_zero, void, env, tl)
 
 /* Special functions */
diff --git a/target/riscv/insn32.decode b/target/riscv/insn32.decode
index 3985bc703f..3788f86528 100644
--- a/target/riscv/insn32.decode
+++ b/target/riscv/insn32.decode
@@ -181,6 +181,11 @@ sraw     0100000 .....  ..... 101 ..... 0111011 @r
 ldu      ............   ..... 111 ..... 0000011 @i
 {
   [
+    # *** RV32 Zicbom Standard Extension ***
+    cbo_clean  0000000 00001 ..... 010 00000 0001111 @sfence_vm
+    cbo_flush  0000000 00010 ..... 010 00000 0001111 @sfence_vm
+    cbo_inval  0000000 00000 ..... 010 00000 0001111 @sfence_vm
+
     # *** RV32 Zicboz Standard Extension ***
     cbo_zero   0000000 00100 ..... 010 00000 0001111 @sfence_vm
   ]
diff --git a/target/riscv/insn_trans/trans_rvzicbo.c.inc b/target/riscv/insn_trans/trans_rvzicbo.c.inc
index feabc28342..7df9c30b58 100644
--- a/target/riscv/insn_trans/trans_rvzicbo.c.inc
+++ b/target/riscv/insn_trans/trans_rvzicbo.c.inc
@@ -16,12 +16,39 @@
  * this program.  If not, see <http://www.gnu.org/licenses/>.
  */
 
+#define REQUIRE_ZICBOM(ctx) do {    \
+    if (!ctx->cfg_ptr->ext_icbom) { \
+        return false;               \
+    }                               \
+} while (0)
+
 #define REQUIRE_ZICBOZ(ctx) do {    \
     if (!ctx->cfg_ptr->ext_icboz) { \
         return false;               \
     }                               \
 } while (0)
 
+static bool trans_cbo_clean(DisasContext *ctx, arg_cbo_clean *a)
+{
+    REQUIRE_ZICBOM(ctx);
+    gen_helper_cbo_clean_flush(cpu_env, cpu_gpr[a->rs1]);
+    return true;
+}
+
+static bool trans_cbo_flush(DisasContext *ctx, arg_cbo_flush *a)
+{
+    REQUIRE_ZICBOM(ctx);
+    gen_helper_cbo_clean_flush(cpu_env, cpu_gpr[a->rs1]);
+    return true;
+}
+
+static bool trans_cbo_inval(DisasContext *ctx, arg_cbo_inval *a)
+{
+    REQUIRE_ZICBOM(ctx);
+    gen_helper_cbo_inval(cpu_env, cpu_gpr[a->rs1]);
+    return true;
+}
+
 static bool trans_cbo_zero(DisasContext *ctx, arg_cbo_zero *a)
 {
     REQUIRE_ZICBOZ(ctx);
diff --git a/target/riscv/op_helper.c b/target/riscv/op_helper.c
index c5053e9446..25ffa324a3 100644
--- a/target/riscv/op_helper.c
+++ b/target/riscv/op_helper.c
@@ -178,6 +178,113 @@ void helper_cbo_zero(CPURISCVState *env, target_ulong address)
     }
 }
 
+/*
+ * check_zicbom_access
+ *
+ * Check access permissions (LOAD, STORE or FETCH as specified in
+ * section 2.5.2 of the CMO specification) for Zicbom, raising
+ * either store page-fault (non-virtualized) or store guest-page
+ * fault (virtualized).
+ */
+static void check_zicbom_access(CPURISCVState *env,
+                                target_ulong address,
+                                uintptr_t ra)
+{
+    RISCVCPU *cpu = env_archcpu(env);
+    int mmu_idx = cpu_mmu_index(env, false);
+    uint16_t cbomlen = cpu->cfg.cbom_blocksize;
+    void *phost;
+    int ret;
+
+    /* Mask off low-bits to align-down to the cache-block. */
+    address &= ~(cbomlen - 1);
+
+    /*
+     * Section 2.5.2 of cmobase v1.0.1:
+     *
+     * "A cache-block management instruction is permitted to
+     * access the specified cache block whenever a load instruction
+     * or store instruction is permitted to access the corresponding
+     * physical addresses. If neither a load instruction nor store
+     * instruction is permitted to access the physical addresses,
+     * but an instruction fetch is permitted to access the physical
+     * addresses, whether a cache-block management instruction is
+     * permitted to access the cache block is UNSPECIFIED.
+     *
+     * This means we have to make a choice of whether checking
+     * MMU_INST_FETCH is worth it or not. We'll go the easier
+     * route and check MMU_DATA_LOAD and MMU_DATA_STORE only.
+     */
+    ret = probe_access_range_flags(env, address, cbomlen,
+                                   MMU_DATA_LOAD,
+                                   mmu_idx, true, &phost, ra);
+
+    if (ret == TLB_INVALID_MASK) {
+        probe_access_range_flags(env, address, cbomlen,
+                                 MMU_DATA_STORE,
+                                 mmu_idx, true, &phost, ra);
+    }
+
+    if (ret == TLB_INVALID_MASK) {
+        /*
+         * If ret == TLB_INVALID_MASK at this point, LOAD and
+         * STORE aren't permitted, meaning that access to the
+         * cache block is not permitted. Same paragraph
+         * mentioned above from cmobase v1.0.1 spec says:
+         *
+         * "If access to the cache block is not permitted, a
+         * cache-block management instruction raises a store
+         * page fault or store guest-page fault exception if
+         * address translation does not permit any access or
+         * raises a store access fault exception otherwise."
+         *
+         * Thus, raise a store (guest-)page fault exception.
+         */
+#ifndef CONFIG_USER_ONLY
+        if (riscv_cpu_virt_enabled(env)) {
+            riscv_raise_exception(env,
+                                  RISCV_EXCP_STORE_GUEST_AMO_ACCESS_FAULT,
+                                  ra);
+        }
+#endif
+        riscv_raise_exception(env, RISCV_EXCP_STORE_AMO_ACCESS_FAULT, ra);
+
+        return;
+    }
+
+    /*
+     * We're still missing PMP faults checks. The spec mentions
+     * that we either raise a store (guest) page fault, which
+     * we're already doing above, or raise a store access fault
+     * otherwise.
+     *
+     * The latter can be achieved by using probe_access_range_flags(),
+     * using MMU_DATA_STORE, with nonfault = false. riscv_cpu_tlb_fill()
+     * will raise the appropriate exception regardless of being a
+     * PMP fault or any other.
+     */
+    probe_access_range_flags(env, address, cbomlen, MMU_DATA_STORE,
+                             mmu_idx, false, &phost, ra);
+}
+
+void helper_cbo_clean_flush(CPURISCVState *env, target_ulong address)
+{
+    uintptr_t ra = GETPC();
+    check_zicbo_envcfg(env, MENVCFG_CBCFE, ra);
+    check_zicbom_access(env, address, ra);
+
+    /* We don't emulate the cache-hierarchy, so we're done. */
+}
+
+void helper_cbo_inval(CPURISCVState *env, target_ulong address)
+{
+    uintptr_t ra = GETPC();
+    check_zicbo_envcfg(env, MENVCFG_CBIE, ra);
+    check_zicbom_access(env, address, ra);
+
+    /* We don't emulate the cache-hierarchy, so we're done. */
+}
+
 #ifndef CONFIG_USER_ONLY
 
 target_ulong helper_sret(CPURISCVState *env)
-- 
2.39.2

[PATCH v6 4/4] target/riscv: add Zicbop cbo.prefetch{i, r, m} placeholder

[Daniel Henrique Barboza]

From: Christoph Muellner <cmuellner@linux.com>

The cmo.prefetch instructions are nops for QEMU (no emulation of the
memory hierarchy, no illegal instructions, no permission faults, no
traps).

Add a comment noting where they would be decoded in case cbo.prefetch
instructions become relevant in the future.

Co-developed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Signed-off-by: Christoph Muellner <cmuellner@linux.com>
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
---
 target/riscv/insn32.decode | 1 +
 1 file changed, 1 insertion(+)

diff --git a/target/riscv/insn32.decode b/target/riscv/insn32.decode
index 3788f86528..1aebd37572 100644
--- a/target/riscv/insn32.decode
+++ b/target/riscv/insn32.decode
@@ -134,6 +134,7 @@ addi     ............     ..... 000 ..... 0010011 @i
 slti     ............     ..... 010 ..... 0010011 @i
 sltiu    ............     ..... 011 ..... 0010011 @i
 xori     ............     ..... 100 ..... 0010011 @i
+# cbo.prefetch_{i,r,m} instructions are ori with rd=x0 and not decoded.
 ori      ............     ..... 110 ..... 0010011 @i
 andi     ............     ..... 111 ..... 0010011 @i
 slli     00000. ......    ..... 001 ..... 0010011 @sh
-- 
2.39.2

Re: [PATCH v6 2/4] target/riscv: implement Zicboz extension

[Richard Henderson]

On 2/17/23 10:34, Daniel Henrique Barboza wrote:
> +void helper_cbo_zero(CPURISCVState *env, target_ulong address)
> +{
> +    RISCVCPU *cpu = env_archcpu(env);
> +    uintptr_t ra = GETPC();
> +    uint16_t cbozlen;
> +    void *mem;
> +
> +    check_zicbo_envcfg(env, MENVCFG_CBZE, ra);
> +
> +    /* Get the size of the cache block for zero instructions. */
> +    cbozlen = cpu->cfg.cboz_blocksize;
> +
> +    /* Mask off low-bits to align-down to the cache-block. */
> +    address &= ~(cbozlen - 1);
> +
> +    mem = tlb_vaddr_to_host(env, address, MMU_DATA_STORE,
> +                            cpu_mmu_index(env, false));
> +
> +    if (likely(mem)) {
> +        /* Zero the block */
> +        memset(mem, 0, cbozlen);
> +    }
> +}

Not correct.  This fails to zero the block at all under a number of conditions.
Please have a closer look at the feedback on v5.


r~

Re: [PATCH v6 3/4] target/riscv: implement Zicbom extension

[Richard Henderson]

On 2/17/23 10:34, Daniel Henrique Barboza wrote:
> +    /*
> +     * Section 2.5.2 of cmobase v1.0.1:
> +     *
> +     * "A cache-block management instruction is permitted to
> +     * access the specified cache block whenever a load instruction
> +     * or store instruction is permitted to access the corresponding
> +     * physical addresses. If neither a load instruction nor store
> +     * instruction is permitted to access the physical addresses,
> +     * but an instruction fetch is permitted to access the physical
> +     * addresses, whether a cache-block management instruction is
> +     * permitted to access the cache block is UNSPECIFIED.
> +     *
> +     * This means we have to make a choice of whether checking
> +     * MMU_INST_FETCH is worth it or not. We'll go the easier
> +     * route and check MMU_DATA_LOAD and MMU_DATA_STORE only.
> +     */
> +    ret = probe_access_range_flags(env, address, cbomlen,
> +                                   MMU_DATA_LOAD,
> +                                   mmu_idx, true, &phost, ra);
> +
> +    if (ret == TLB_INVALID_MASK) {
> +        probe_access_range_flags(env, address, cbomlen,
> +                                 MMU_DATA_STORE,
> +                                 mmu_idx, true, &phost, ra);
> +    }

Not correct, at minimum for discarding the result of the second call.  But I suggested a 
different ordering of operations which avoid a third probe.


r~

Re: [PATCH v6 2/4] target/riscv: implement Zicboz extension

[Daniel Henrique Barboza]

On 2/18/23 00:44, Richard Henderson wrote:
> On 2/17/23 10:34, Daniel Henrique Barboza wrote:
>> +void helper_cbo_zero(CPURISCVState *env, target_ulong address)
>> +{
>> +    RISCVCPU *cpu = env_archcpu(env);
>> +    uintptr_t ra = GETPC();
>> +    uint16_t cbozlen;
>> +    void *mem;
>> +
>> +    check_zicbo_envcfg(env, MENVCFG_CBZE, ra);
>> +
>> +    /* Get the size of the cache block for zero instructions. */
>> +    cbozlen = cpu->cfg.cboz_blocksize;
>> +
>> +    /* Mask off low-bits to align-down to the cache-block. */
>> +    address &= ~(cbozlen - 1);
>> +
>> +    mem = tlb_vaddr_to_host(env, address, MMU_DATA_STORE,
>> +                            cpu_mmu_index(env, false));
>> +
>> +    if (likely(mem)) {
>> +        /* Zero the block */
>> +        memset(mem, 0, cbozlen);
>> +    }
>> +}
> 
> Not correct.  This fails to zero the block at all under a number of conditions.

Ops. The 'else' conditional in which we would zero the mem in case it's an I/O
region got lost in the middle of rebasing it seems ....

By the way, looking at the lack of any probing in this particular function and at
the probe_writes() that ARM does, I read the spec again. A paragraph in 2.5.2
says:

"A cache-block zero instruction is permitted to access the specified cache block whenever
a store instruction is permitted to access the corresponding physical addresses and when
the PMAs indicate that cache-block zero instructions are a supported access type. If access
to the cache block is not permitted, a cache-block zero instruction raises a store page fault
or store guest-page fault exception if address translation does not permit write access or
raises a store access fault exception otherwise. During address translation, the instruction
also checks the accessed and dirty bits and may either raise an exception or set the bits as
required."

PMA (Physical Memory Access) doesn't seem to be implemented in RISC-V, or at the very least
it's not using the PMA acronym, so let's skip that for now. I'll add a comment mentioning
it in the code mentioning that PMA for I/O should be checked and we're not doing it.

But PMA aside, we have wording and conditionals that resembles the cache-block management
permissions and so on, with the exception that we're not caring about LOAD access this time
around. So I guess we'll also need here something like what check_zicbom_access() is doing
in the next patch.


Thanks,

Daniel



> Please have a closer look at the feedback on v5.
> 
> 
> r~

Re: [PATCH v6 2/4] target/riscv: implement Zicboz extension

[weiwei]

On 2023/2/18 04:34, Daniel Henrique Barboza wrote:
> From: Christoph Muellner <cmuellner@linux.com>
>
> The RISC-V base cache management operation (CBO) ISA extension has been
> ratified. It defines three extensions: Cache-Block Management, Cache-Block
> Prefetch and Cache-Block Zero. More information about the spec can be
> found at [1].
>
> Let's start by implementing the Cache-Block Zero extension, Zicboz. It
> uses the cbo.zero instruction that, as with all CBO instructions that
> will be added later, needs to be implemented in an overlap group with
> the LQ instruction due to overlapping patterns.
>
> cbo.zero throws a Illegal Instruction/Virtual Instruction exception
> depending on CSR state. This is also the case for the remaining cbo
> instructions we're going to add next, so create a check_zicbo_envcfg()
> that will be used by all Zicbo[mz] instructions.
>
> [1] https://github.com/riscv/riscv-CMOs/blob/master/specifications/cmobase-v1.0.1.pdf
>
> Co-developed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
> Signed-off-by: Christoph Muellner <cmuellner@linux.com>
> Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
> ---
>   target/riscv/cpu.c                          |  4 ++
>   target/riscv/cpu.h                          |  2 +
>   target/riscv/helper.h                       |  3 ++
>   target/riscv/insn32.decode                  | 10 +++-
>   target/riscv/insn_trans/trans_rvzicbo.c.inc | 30 +++++++++++
>   target/riscv/op_helper.c                    | 55 +++++++++++++++++++++
>   target/riscv/translate.c                    |  1 +
>   7 files changed, 104 insertions(+), 1 deletion(-)
>   create mode 100644 target/riscv/insn_trans/trans_rvzicbo.c.inc
>
> diff --git a/target/riscv/cpu.c b/target/riscv/cpu.c
> index 93b52b826c..7dd37de7f9 100644
> --- a/target/riscv/cpu.c
> +++ b/target/riscv/cpu.c
> @@ -74,6 +74,7 @@ struct isa_ext_data {
>   static const struct isa_ext_data isa_edata_arr[] = {
>       ISA_EXT_DATA_ENTRY(h, false, PRIV_VERSION_1_12_0, ext_h),
>       ISA_EXT_DATA_ENTRY(v, false, PRIV_VERSION_1_10_0, ext_v),
> +    ISA_EXT_DATA_ENTRY(zicboz, true, PRIV_VERSION_1_12_0, ext_icboz),
>       ISA_EXT_DATA_ENTRY(zicsr, true, PRIV_VERSION_1_10_0, ext_icsr),
>       ISA_EXT_DATA_ENTRY(zifencei, true, PRIV_VERSION_1_10_0, ext_ifencei),
>       ISA_EXT_DATA_ENTRY(zihintpause, true, PRIV_VERSION_1_10_0, ext_zihintpause),
> @@ -1126,6 +1127,9 @@ static Property riscv_cpu_extensions[] = {
>       DEFINE_PROP_BOOL("zhinx", RISCVCPU, cfg.ext_zhinx, false),
>       DEFINE_PROP_BOOL("zhinxmin", RISCVCPU, cfg.ext_zhinxmin, false),
>   
> +    DEFINE_PROP_BOOL("zicboz", RISCVCPU, cfg.ext_icboz, true),
> +    DEFINE_PROP_UINT16("cboz_blocksize", RISCVCPU, cfg.cboz_blocksize, 64),
> +
>       DEFINE_PROP_BOOL("zmmul", RISCVCPU, cfg.ext_zmmul, false),
>   
>       /* Vendor-specific custom extensions */
> diff --git a/target/riscv/cpu.h b/target/riscv/cpu.h
> index 7128438d8e..6b4c714d3a 100644
> --- a/target/riscv/cpu.h
> +++ b/target/riscv/cpu.h
> @@ -447,6 +447,7 @@ struct RISCVCPUConfig {
>       bool ext_zkt;
>       bool ext_ifencei;
>       bool ext_icsr;
> +    bool ext_icboz;
>       bool ext_zihintpause;
>       bool ext_smstateen;
>       bool ext_sstc;
> @@ -494,6 +495,7 @@ struct RISCVCPUConfig {
>       char *vext_spec;
>       uint16_t vlen;
>       uint16_t elen;
> +    uint16_t cboz_blocksize;
>       bool mmu;
>       bool pmp;
>       bool epmp;
> diff --git a/target/riscv/helper.h b/target/riscv/helper.h
> index 0497370afd..ce165821b8 100644
> --- a/target/riscv/helper.h
> +++ b/target/riscv/helper.h
> @@ -97,6 +97,9 @@ DEF_HELPER_FLAGS_2(fcvt_h_l, TCG_CALL_NO_RWG, i64, env, tl)
>   DEF_HELPER_FLAGS_2(fcvt_h_lu, TCG_CALL_NO_RWG, i64, env, tl)
>   DEF_HELPER_FLAGS_2(fclass_h, TCG_CALL_NO_RWG_SE, tl, env, i64)
>   
> +/* Cache-block operations */
> +DEF_HELPER_2(cbo_zero, void, env, tl)
> +
>   /* Special functions */
>   DEF_HELPER_2(csrr, tl, env, int)
>   DEF_HELPER_3(csrw, void, env, int, tl)
> diff --git a/target/riscv/insn32.decode b/target/riscv/insn32.decode
> index b7e7613ea2..3985bc703f 100644
> --- a/target/riscv/insn32.decode
> +++ b/target/riscv/insn32.decode
> @@ -179,7 +179,15 @@ sraw     0100000 .....  ..... 101 ..... 0111011 @r
>   
>   # *** RV128I Base Instruction Set (in addition to RV64I) ***
>   ldu      ............   ..... 111 ..... 0000011 @i
> -lq       ............   ..... 010 ..... 0001111 @i
> +{
> +  [
> +    # *** RV32 Zicboz Standard Extension ***
> +    cbo_zero   0000000 00100 ..... 010 00000 0001111 @sfence_vm
> +  ]
> +
> +  # *** RVI128 lq ***
> +  lq       ............   ..... 010 ..... 0001111 @i
> +}
>   sq       ............   ..... 100 ..... 0100011 @s
>   addid    ............  .....  000 ..... 1011011 @i
>   sllid    000000 ......  ..... 001 ..... 1011011 @sh6
> diff --git a/target/riscv/insn_trans/trans_rvzicbo.c.inc b/target/riscv/insn_trans/trans_rvzicbo.c.inc
> new file mode 100644
> index 0000000000..feabc28342
> --- /dev/null
> +++ b/target/riscv/insn_trans/trans_rvzicbo.c.inc
> @@ -0,0 +1,30 @@
> +/*
> + * RISC-V translation routines for the RISC-V CBO Extension.
> + *
> + * Copyright (c) 2021 Philipp Tomsich, philipp.tomsich@vrull.eu
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2 or later, as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
> + * more details.
> + *
> + * You should have received a copy of the GNU General Public License along with
> + * this program.  If not, see <http://www.gnu.org/licenses/>.
> + */
> +
> +#define REQUIRE_ZICBOZ(ctx) do {    \
> +    if (!ctx->cfg_ptr->ext_icboz) { \
> +        return false;               \
> +    }                               \
> +} while (0)
> +
> +static bool trans_cbo_zero(DisasContext *ctx, arg_cbo_zero *a)
> +{
> +    REQUIRE_ZICBOZ(ctx);
> +    gen_helper_cbo_zero(cpu_env, cpu_gpr[a->rs1]);
> +    return true;
> +}
> diff --git a/target/riscv/op_helper.c b/target/riscv/op_helper.c
> index 48f918b71b..c5053e9446 100644
> --- a/target/riscv/op_helper.c
> +++ b/target/riscv/op_helper.c
> @@ -3,6 +3,7 @@
>    *
>    * Copyright (c) 2016-2017 Sagar Karandikar, sagark@eecs.berkeley.edu
>    * Copyright (c) 2017-2018 SiFive, Inc.
> + * Copyright (c) 2022      VRULL GmbH
>    *
>    * This program is free software; you can redistribute it and/or modify it
>    * under the terms and conditions of the GNU General Public License,
> @@ -123,6 +124,60 @@ target_ulong helper_csrrw_i128(CPURISCVState *env, int csr,
>       return int128_getlo(rv);
>   }
>   
> +
> +/*
> + * check_zicbo_envcfg
> + *
> + * Raise virtual exceptions and illegal instruction exceptions for
> + * Zicbo[mz] instructions based on the settings of [mhs]envcfg as
> + * specified in section 2.5.1 of the CMO specification.
> + */
> +static void check_zicbo_envcfg(CPURISCVState *env, target_ulong envbits,
> +                                uintptr_t ra)
> +{
> +#ifndef CONFIG_USER_ONLY
> +    /*
> +     * Check for virtual instruction exceptions first, as we don't see
> +     * VU and VS reflected in env->priv (these are just the translated
> +     * U and S stated with virtualisation enabled.
> +     */
> +    if (riscv_cpu_virt_enabled(env) &&
> +        (((env->priv < PRV_H) && !get_field(env->henvcfg, envbits)) ||
> +         ((env->priv < PRV_S) && !get_field(env->senvcfg, envbits)))) {
> +        riscv_raise_exception(env, RISCV_EXCP_VIRT_INSTRUCTION_FAULT, ra);
> +    }

Check of (env->priv < PRV_M) && !get_field(env->menvcfg, envbits) should 
be put before upper check.

Illegal instruction exception should be triggered if (env->priv < PRV_M) 
&& !get_field(env->menvcfg, envbits).

However, virtual instruction exception may be triggered if we do upper 
check firstly.

Regards,

Weiwei Li

> +
> +    if (((env->priv < PRV_M) && !get_field(env->menvcfg, envbits)) ||
> +        ((env->priv < PRV_S) && !get_field(env->senvcfg, envbits))) {
> +        riscv_raise_exception(env, RISCV_EXCP_ILLEGAL_INST, ra);
> +    }
> +#endif
> +}
> +
> +void helper_cbo_zero(CPURISCVState *env, target_ulong address)
> +{
> +    RISCVCPU *cpu = env_archcpu(env);
> +    uintptr_t ra = GETPC();
> +    uint16_t cbozlen;
> +    void *mem;
> +
> +    check_zicbo_envcfg(env, MENVCFG_CBZE, ra);
> +
> +    /* Get the size of the cache block for zero instructions. */
> +    cbozlen = cpu->cfg.cboz_blocksize;
> +
> +    /* Mask off low-bits to align-down to the cache-block. */
> +    address &= ~(cbozlen - 1);
> +
> +    mem = tlb_vaddr_to_host(env, address, MMU_DATA_STORE,
> +                            cpu_mmu_index(env, false));
> +
> +    if (likely(mem)) {
> +        /* Zero the block */
> +        memset(mem, 0, cbozlen);
> +    }
> +}
> +
>   #ifndef CONFIG_USER_ONLY
>   
>   target_ulong helper_sret(CPURISCVState *env)
> diff --git a/target/riscv/translate.c b/target/riscv/translate.c
> index 772f9d7973..7f687a7e37 100644
> --- a/target/riscv/translate.c
> +++ b/target/riscv/translate.c
> @@ -1104,6 +1104,7 @@ static uint32_t opcode_at(DisasContextBase *dcbase, target_ulong pc)
>   #include "insn_trans/trans_rvv.c.inc"
>   #include "insn_trans/trans_rvb.c.inc"
>   #include "insn_trans/trans_rvzawrs.c.inc"
> +#include "insn_trans/trans_rvzicbo.c.inc"
>   #include "insn_trans/trans_rvzfh.c.inc"
>   #include "insn_trans/trans_rvk.c.inc"
>   #include "insn_trans/trans_privileged.c.inc"

Re: [PATCH v6 2/4] target/riscv: implement Zicboz extension

[Richard Henderson]

On 2/17/23 23:28, Daniel Henrique Barboza wrote:
> "A cache-block zero instruction is permitted to access the specified cache block whenever
> a store instruction is permitted to access the corresponding physical addresses and when
> the PMAs indicate that cache-block zero instructions are a supported access type. If access
> to the cache block is not permitted, a cache-block zero instruction raises a store page fault
> or store guest-page fault exception if address translation does not permit write access or
> raises a store access fault exception otherwise. During address translation, the instruction
> also checks the accessed and dirty bits and may either raise an exception or set the bits as
> required."

By the way, I think the documentation should specify what happens if the page is *not* 
accessible.  Is badaddr = {rN, aligned(rN), unspecified, but somewhere in the block}?


r~

Re: [PATCH v6 2/4] target/riscv: implement Zicboz extension

[Daniel Henrique Barboza]

On 2/18/23 16:35, Richard Henderson wrote:
> On 2/17/23 23:28, Daniel Henrique Barboza wrote:
>> "A cache-block zero instruction is permitted to access the specified cache block whenever
>> a store instruction is permitted to access the corresponding physical addresses and when
>> the PMAs indicate that cache-block zero instructions are a supported access type. If access
>> to the cache block is not permitted, a cache-block zero instruction raises a store page fault
>> or store guest-page fault exception if address translation does not permit write access or
>> raises a store access fault exception otherwise. During address translation, the instruction
>> also checks the accessed and dirty bits and may either raise an exception or set the bits as
>> required."
> 
> By the way, I think the documentation should specify what happens if the page is *not* accessible.  Is badaddr = {rN, aligned(rN), unspecified, but somewhere in the block}?
> 

Do you mean that the doc should tell whether the address to be returned in the store
access fault should be aligned and whatnot?

Yeah, this is not mentioned in the docs. I think you're wondering if we should do like
ARM does, like you're mentioned in the previous version:

=======
While re-reading the ARM code, I remembered that the ARM dc.zva instruction is required
to produce original unmasked address on a page fault, thus the little dance with two
calls to probe_write.
=======

By reading target/riscv code it seems that all store acess faults are being fired via
raise_mmu_exception(), which is only called in riscv_cpu_tlb_fill(), which in turn
doesn't do any thing special with the address before firing the exception. So I guess
we can assume that badddr = aligned?



Daniel


> 
> r~

Re: [PATCH v6 2/4] target/riscv: implement Zicboz extension

[Richard Henderson]

On 2/21/23 23:37, Daniel Henrique Barboza wrote:
> Do you mean that the doc should tell whether the address to be returned in the store
> access fault should be aligned and whatnot?

Yes.

> By reading target/riscv code it seems that all store acess faults are being fired via
> raise_mmu_exception(), which is only called in riscv_cpu_tlb_fill(), which in turn
> doesn't do any thing special with the address before firing the exception. So I guess
> we can assume that badddr = aligned?

Well that's certainly how the code is written, yes.


r~