Re: [PATCH v2 6/7] usb/ohci: Implement resume on connection status change

["Philippe Mathieu-Daudé" <philmd@linaro.org>]

On 20/2/23 19:19, BALATON Zoltan wrote:
> If certain bit is set remote wake up should change state from
> suspended to resume and generate interrupt. There was a todo comment
> for this, implement that by moving existing resume logic to a function
> and call that.
> 
> Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
> ---
>   hw/usb/hcd-ohci.c | 23 +++++++++++++++++------
>   1 file changed, 17 insertions(+), 6 deletions(-)
> 
> diff --git a/hw/usb/hcd-ohci.c b/hw/usb/hcd-ohci.c
> index bad8db7b1d..88bd42b14a 100644
> --- a/hw/usb/hcd-ohci.c
> +++ b/hw/usb/hcd-ohci.c
> @@ -1410,6 +1410,18 @@ static void ohci_set_hub_status(OHCIState *ohci, uint32_t val)
>       }
>   }
>   
> +/* This is the one state transition the controller can do by itself */
> +static int ohci_resume(OHCIState *s)

Preferably returning bool.

> +{
> +    if ((s->ctl & OHCI_CTL_HCFS) == OHCI_USB_SUSPEND) {
> +        trace_usb_ohci_remote_wakeup(s->name);
> +        s->ctl &= ~OHCI_CTL_HCFS;
> +        s->ctl |= OHCI_USB_RESUME;
> +        return 1;
> +    }
> +    return 0;
> +}
> +
>   /*
>    * Sets a flag in a port status reg but only set it if the port is connected.
>    * If not set ConnectStatusChange flag. If flag is enabled return 1.
> @@ -1426,7 +1438,10 @@ static int ohci_port_set_if_connected(OHCIState *ohci, int i, uint32_t val)
>       if (!(ohci->rhport[i].ctrl & OHCI_PORT_CCS)) {
>           ohci->rhport[i].ctrl |= OHCI_PORT_CSC;

// ConnectStatusChange

>           if (ohci->rhstatus & OHCI_RHS_DRWE) {

// DeviceRemoteWakeupEnable: ConnectStatusChange is a remote wakeup event.

> -            /* TODO: CSC is a wakeup event */
> +            /* CSC is a wakeup event */
> +            if (ohci_resume(ohci)) {
> +                ohci_set_interrupt(ohci, OHCI_INTR_RD);

Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>

Gerd, if you Ack I can queue this.

> +            }
>           }
>           return 0;
>       }
> @@ -1828,11 +1843,7 @@ static void ohci_wakeup(USBPort *port1)
>           intr = OHCI_INTR_RHSC;
>       }
>       /* Note that the controller can be suspended even if this port is not */
> -    if ((s->ctl & OHCI_CTL_HCFS) == OHCI_USB_SUSPEND) {
> -        trace_usb_ohci_remote_wakeup(s->name);
> -        /* This is the one state transition the controller can do by itself */
> -        s->ctl &= ~OHCI_CTL_HCFS;
> -        s->ctl |= OHCI_USB_RESUME;
> +    if (ohci_resume(s)) {
>           /*
>            * In suspend mode only ResumeDetected is possible, not RHSC:
>            * see the OHCI spec 5.1.2.3.