From: David Gibson <david@gibson.dropbear.id.au>
To: Daniel Henrique Barboza <danielhb413@gmail.com>
Cc: gustavo.romero@linaro.org, richard.henderson@linaro.org,
qemu-devel@nongnu.org, groug@kaod.org, qemu-ppc@nongnu.org,
clg@kaod.org
Subject: Re: [PATCH v2 01/16] target/ppc: add user write access control for PMU SPRs
Date: Wed, 25 Aug 2021 14:26:49 +1000 [thread overview]
Message-ID: <YSXGiZeWLI+L0/lr@yekko> (raw)
In-Reply-To: <20210824163032.394099-2-danielhb413@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 9256 bytes --]
On Tue, Aug 24, 2021 at 01:30:17PM -0300, Daniel Henrique Barboza wrote:
> We're going to add PMU support for TCG PPC64 chips, based on IBM POWER8+
> emulation and following PowerISA v3.1.
>
> PowerISA v3.1 defines two PMU registers groups, A and B:
>
> - group A contains all performance monitor counters (PMCs), MMCR0, MMCR2
> and MMCRA;
>
> - group B contains MMCR1, MMCR3, SIER, SIER2, SIER3, SIAR, SDAR.
>
> Group A have read/write non-privileged access depending on MMCR0_PMCC
> bits. Group B is always userspace read only.
>
> Userspace will require to write Group A registers, and at the same time
> some Linux PMU selftests deliberately test if we are allowing write
> access when we shouldn't. This patch address the access control of Group
> A PMU registers by doing the following:
>
> - add a 'pmcc_clear' flag in DisasContext. This will map whether
> MMCR0_PMCC bits are cleared by checking HFLAGS_PMCCCLEAR;
>
> - create a spr_write_PMU_groupA_ureg() that will be used to all
> userspace writes of PMU regs. The reg will apply the proper access
> control before forwarding execution to spr_write_ureg().
>
> Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Hoping to get a review from Richard as well before merging.
> ---
> target/ppc/cpu.h | 4 ++++
> target/ppc/cpu_init.c | 18 +++++++++---------
> target/ppc/helper_regs.c | 3 +++
> target/ppc/spr_tcg.h | 1 +
> target/ppc/translate.c | 37 +++++++++++++++++++++++++++++++++++++
> 5 files changed, 54 insertions(+), 9 deletions(-)
>
> diff --git a/target/ppc/cpu.h b/target/ppc/cpu.h
> index 500205229c..627fc8d732 100644
> --- a/target/ppc/cpu.h
> +++ b/target/ppc/cpu.h
> @@ -342,6 +342,9 @@ typedef struct ppc_v3_pate_t {
> #define MSR_RI 1 /* Recoverable interrupt 1 */
> #define MSR_LE 0 /* Little-endian mode 1 hflags */
>
> +/* PMU bits */
> +#define MMCR0_PMCC PPC_BITMASK(44, 45) /* PMC Control */
> +
> /* LPCR bits */
> #define LPCR_VPM0 PPC_BIT(0)
> #define LPCR_VPM1 PPC_BIT(1)
> @@ -606,6 +609,7 @@ enum {
> HFLAGS_SE = 10, /* MSR_SE -- from elsewhere on embedded ppc */
> HFLAGS_FP = 13, /* MSR_FP */
> HFLAGS_PR = 14, /* MSR_PR */
> + HFLAGS_PMCCCLEAR = 15, /* PMU MMCR0 PMCC equal to 0b00 */
> HFLAGS_VSX = 23, /* MSR_VSX if cpu has VSX */
> HFLAGS_VR = 25, /* MSR_VR if cpu has VRE */
>
> diff --git a/target/ppc/cpu_init.c b/target/ppc/cpu_init.c
> index 66deb18a6b..c72c7fabea 100644
> --- a/target/ppc/cpu_init.c
> +++ b/target/ppc/cpu_init.c
> @@ -6868,7 +6868,7 @@ static void register_book3s_pmu_sup_sprs(CPUPPCState *env)
> static void register_book3s_pmu_user_sprs(CPUPPCState *env)
> {
> spr_register(env, SPR_POWER_UMMCR0, "UMMCR0",
> - &spr_read_ureg, SPR_NOACCESS,
> + &spr_read_ureg, &spr_write_PMU_groupA_ureg,
> &spr_read_ureg, &spr_write_ureg,
> 0x00000000);
> spr_register(env, SPR_POWER_UMMCR1, "UMMCR1",
> @@ -6876,31 +6876,31 @@ static void register_book3s_pmu_user_sprs(CPUPPCState *env)
> &spr_read_ureg, &spr_write_ureg,
> 0x00000000);
> spr_register(env, SPR_POWER_UMMCRA, "UMMCRA",
> - &spr_read_ureg, SPR_NOACCESS,
> + &spr_read_ureg, &spr_write_PMU_groupA_ureg,
> &spr_read_ureg, &spr_write_ureg,
> 0x00000000);
> spr_register(env, SPR_POWER_UPMC1, "UPMC1",
> - &spr_read_ureg, SPR_NOACCESS,
> + &spr_read_ureg, &spr_write_PMU_groupA_ureg,
> &spr_read_ureg, &spr_write_ureg,
> 0x00000000);
> spr_register(env, SPR_POWER_UPMC2, "UPMC2",
> - &spr_read_ureg, SPR_NOACCESS,
> + &spr_read_ureg, &spr_write_PMU_groupA_ureg,
> &spr_read_ureg, &spr_write_ureg,
> 0x00000000);
> spr_register(env, SPR_POWER_UPMC3, "UPMC3",
> - &spr_read_ureg, SPR_NOACCESS,
> + &spr_read_ureg, &spr_write_PMU_groupA_ureg,
> &spr_read_ureg, &spr_write_ureg,
> 0x00000000);
> spr_register(env, SPR_POWER_UPMC4, "UPMC4",
> - &spr_read_ureg, SPR_NOACCESS,
> + &spr_read_ureg, &spr_write_PMU_groupA_ureg,
> &spr_read_ureg, &spr_write_ureg,
> 0x00000000);
> spr_register(env, SPR_POWER_UPMC5, "UPMC5",
> - &spr_read_ureg, SPR_NOACCESS,
> + &spr_read_ureg, &spr_write_PMU_groupA_ureg,
> &spr_read_ureg, &spr_write_ureg,
> 0x00000000);
> spr_register(env, SPR_POWER_UPMC6, "UPMC6",
> - &spr_read_ureg, SPR_NOACCESS,
> + &spr_read_ureg, &spr_write_PMU_groupA_ureg,
> &spr_read_ureg, &spr_write_ureg,
> 0x00000000);
> spr_register(env, SPR_POWER_USIAR, "USIAR",
> @@ -6976,7 +6976,7 @@ static void register_power8_pmu_sup_sprs(CPUPPCState *env)
> static void register_power8_pmu_user_sprs(CPUPPCState *env)
> {
> spr_register(env, SPR_POWER_UMMCR2, "UMMCR2",
> - &spr_read_ureg, SPR_NOACCESS,
> + &spr_read_ureg, &spr_write_PMU_groupA_ureg,
> &spr_read_ureg, &spr_write_ureg,
> 0x00000000);
> spr_register(env, SPR_POWER_USIER, "USIER",
> diff --git a/target/ppc/helper_regs.c b/target/ppc/helper_regs.c
> index 405450d863..4c1d9575ac 100644
> --- a/target/ppc/helper_regs.c
> +++ b/target/ppc/helper_regs.c
> @@ -106,6 +106,9 @@ static uint32_t hreg_compute_hflags_value(CPUPPCState *env)
> if (env->spr[SPR_LPCR] & LPCR_GTSE) {
> hflags |= 1 << HFLAGS_GTSE;
> }
> + if (((env->spr[SPR_POWER_MMCR0] & MMCR0_PMCC) >> 18) == 0) {
> + hflags |= 1 << HFLAGS_PMCCCLEAR;
> + }
>
> #ifndef CONFIG_USER_ONLY
> if (!env->has_hv_mode || (msr & (1ull << MSR_HV))) {
> diff --git a/target/ppc/spr_tcg.h b/target/ppc/spr_tcg.h
> index 0be5f347d5..027ec4c3f7 100644
> --- a/target/ppc/spr_tcg.h
> +++ b/target/ppc/spr_tcg.h
> @@ -40,6 +40,7 @@ void spr_read_601_rtcl(DisasContext *ctx, int gprn, int sprn);
> void spr_read_601_rtcu(DisasContext *ctx, int gprn, int sprn);
> void spr_read_spefscr(DisasContext *ctx, int gprn, int sprn);
> void spr_write_spefscr(DisasContext *ctx, int sprn, int gprn);
> +void spr_write_PMU_groupA_ureg(DisasContext *ctx, int sprn, int gprn);
>
> #ifndef CONFIG_USER_ONLY
> void spr_write_generic32(DisasContext *ctx, int sprn, int gprn);
> diff --git a/target/ppc/translate.c b/target/ppc/translate.c
> index 171b216e17..3a1eafbba8 100644
> --- a/target/ppc/translate.c
> +++ b/target/ppc/translate.c
> @@ -175,6 +175,7 @@ struct DisasContext {
> bool spe_enabled;
> bool tm_enabled;
> bool gtse;
> + bool pmcc_clear;
> ppc_spr_t *spr_cb; /* Needed to check rights for mfspr/mtspr */
> int singlestep_enabled;
> uint32_t flags;
> @@ -526,6 +527,41 @@ void spr_write_ureg(DisasContext *ctx, int sprn, int gprn)
> }
> #endif
>
> +#if defined(TARGET_PPC64) && !defined(CONFIG_USER_ONLY)
> +/*
> + * User write function for PMU group A regs. PowerISA v3.1
> + * defines Group A sprs as:
> + *
> + * "The non-privileged read/write Performance Monitor registers
> + * (i.e., the PMCs, MMCR0, MMCR2, and MMCRA at SPR numbers
> + * 771-776, 779, 769, and 770, respectively)"
> + *
> + * These SPRs have a common user write access control via
> + * MMCR0 bits 44 and 45 (PMCC).
> + */
> +void spr_write_PMU_groupA_ureg(DisasContext *ctx, int sprn, int gprn)
> +{
> + /*
> + * For group A PMU sprs, if PMCC = 0b00, PowerISA v3.1
> + * dictates that:
> + *
> + * "If an attempt is made to write to an SPR in group A in
> + * problem state, a Hypervisor Emulation Assistance
> + * interrupt will occur."
> + */
> + if (ctx->pmcc_clear) {
> + gen_hvpriv_exception(ctx, POWERPC_EXCP_INVAL_SPR);
> + return;
> + }
> + spr_write_ureg(ctx, sprn, gprn);
> +}
> +#else
> +void spr_write_PMU_groupA_ureg(DisasContext *ctx, int sprn, int gprn)
> +{
> + spr_noaccess(ctx, gprn, sprn);
> +}
> +#endif
> +
> /* SPR common to all non-embedded PowerPC */
> /* DECR */
> #if !defined(CONFIG_USER_ONLY)
> @@ -8539,6 +8575,7 @@ static void ppc_tr_init_disas_context(DisasContextBase *dcbase, CPUState *cs)
> ctx->vsx_enabled = (hflags >> HFLAGS_VSX) & 1;
> ctx->tm_enabled = (hflags >> HFLAGS_TM) & 1;
> ctx->gtse = (hflags >> HFLAGS_GTSE) & 1;
> + ctx->pmcc_clear = (hflags >> HFLAGS_PMCCCLEAR) & 1;
>
> ctx->singlestep_enabled = 0;
> if ((hflags >> HFLAGS_SE) & 1) {
--
David Gibson | I'll have my music baroque, and my code
david AT gibson.dropbear.id.au | minimalist, thank you. NOT _the_ _other_
| _way_ _around_!
http://www.ozlabs.org/~dgibson
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
next prev parent reply other threads:[~2021-08-25 4:54 UTC|newest]
Thread overview: 33+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-08-24 16:30 [PATCH v2 00/16] PMU-EBB support for PPC64 TCG Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 01/16] target/ppc: add user write access control for PMU SPRs Daniel Henrique Barboza
2021-08-25 4:26 ` David Gibson [this message]
2021-08-24 16:30 ` [PATCH v2 02/16] target/ppc: add user read functions for MMCR0 and MMCR2 Daniel Henrique Barboza
2021-08-25 4:30 ` David Gibson
2021-08-25 12:25 ` Paul A. Clarke
2021-08-25 13:35 ` David Gibson
2021-08-24 16:30 ` [PATCH v2 03/16] target/ppc: add exclusive user write function for MMCR0 Daniel Henrique Barboza
2021-08-25 4:37 ` David Gibson
2021-08-25 14:01 ` Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 04/16] target/ppc: PMU basic cycle count for pseries TCG Daniel Henrique Barboza
2021-08-25 5:19 ` David Gibson
2021-08-25 14:05 ` Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 05/16] target/ppc/power8_pmu.c: enable PMC1-PMC4 events Daniel Henrique Barboza
2021-08-25 5:23 ` David Gibson
2021-08-24 16:30 ` [PATCH v2 06/16] target/ppc: PMU: add instruction counting Daniel Henrique Barboza
2021-08-25 5:31 ` David Gibson
2021-08-25 14:10 ` Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 07/16] target/ppc/power8_pmu.c: add PM_RUN_INST_CMPL (0xFA) event Daniel Henrique Barboza
2021-08-25 5:32 ` David Gibson
2021-08-24 16:30 ` [PATCH v2 08/16] target/ppc/power8_pmu.c: add PMC14/PMC56 counter freeze bits Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 09/16] PPC64/TCG: Implement 'rfebb' instruction Daniel Henrique Barboza
2021-08-30 12:12 ` Matheus K. Ferst
2021-08-30 18:41 ` Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 10/16] target/ppc: PMU Event-Based exception support Daniel Henrique Barboza
2021-08-25 5:37 ` David Gibson
2021-08-30 19:09 ` Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 11/16] target/ppc/excp_helper.c: EBB handling adjustments Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 12/16] target/ppc/power8_pmu.c: enable PMC1 counter negative overflow Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 13/16] target/ppc/power8_pmu.c: cycles overflow with all PMCs Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 14/16] target/ppc: PMU: insns counter negative overflow support Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 15/16] target/ppc/translate: PMU: handle setting of PMCs while running Daniel Henrique Barboza
2021-08-24 16:30 ` [PATCH v2 16/16] target/ppc/power8_pmu.c: handle overflow bits when PMU is running Daniel Henrique Barboza
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=YSXGiZeWLI+L0/lr@yekko \
--to=david@gibson.dropbear.id.au \
--cc=clg@kaod.org \
--cc=danielhb413@gmail.com \
--cc=groug@kaod.org \
--cc=gustavo.romero@linaro.org \
--cc=qemu-devel@nongnu.org \
--cc=qemu-ppc@nongnu.org \
--cc=richard.henderson@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).