* [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality
@ 2019-04-09 2:01 Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
` (10 more replies)
0 siblings, 11 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel; +Cc: Kevin Wolf, Max Reitz, qemu-block, Stephen Checkoway
The goal of this patch series implement the following AMD command-set parallel
flash functionality:
- flash interleaving;
- nonuniform sector sizes;
- erase suspend/resume commands; and
- multi-sector erase.
During refactoring and implementation, I discovered several bugs that are
fixed here as well:
- flash commands use only 11-bits of the address in most cases, but the
current code uses all of them [1];
- entering CFI mode from autoselect mode and then exiting CFI mode should
return the chip to autoselect mode, but the current code returns to read
array mode; and
- reset command should be ignored during sector/chip erase, but the current
code performs the reset.
The first patch in the series adds a test for the existing behavior. Tests for
additional behavior/bug fixes are added in the relevant patch.
1. I found firmware in the wild that relies on the 11-bit address behavior,
probably due to a bug in the firmware itself.
Changes from v1:
- Fix missing spaces around *, -, and ?.
- Fix missing Signed-off-by line on patch 7
- Replace use of errc with g_printerr and exit
Stephen Checkoway (10):
block/pflash_cfi02: Add test for supported commands
block/pflash_cfi02: Refactor, NFC intended
block/pflash_cfi02: Fix command address comparison
block/pflash_cfi02: Implement intereleaved flash devices
block/pflash_cfi02: Implement nonuniform sector sizes
block/pflash_cfi02: Fix CFI in autoselect mode
block/pflash_cfi02: Fix reset command not ignored during erase
block/pflash_cfi02: Implement multi-sector erase
block/pflash_cfi02: Implement erase suspend/resume
block/pflash_cfi02: Use the chip erase time specified in the CFI table
hw/block/pflash_cfi02.c | 843 +++++++++++++++++++++++++++-----------
tests/Makefile.include | 2 +
tests/pflash-cfi02-test.c | 759 ++++++++++++++++++++++++++++++++++
3 files changed, 1367 insertions(+), 237 deletions(-)
create mode 100644 tests/pflash-cfi02-test.c
--
2.20.1 (Apple Git-117)
^ permalink raw reply [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 01/10] block/pflash_cfi02: Add test for supported commands Stephen Checkoway
` (9 subsequent siblings)
10 siblings, 0 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel; +Cc: Kevin Wolf, Stephen Checkoway, qemu-block, Max Reitz
The goal of this patch series implement the following AMD command-set parallel
flash functionality:
- flash interleaving;
- nonuniform sector sizes;
- erase suspend/resume commands; and
- multi-sector erase.
During refactoring and implementation, I discovered several bugs that are
fixed here as well:
- flash commands use only 11-bits of the address in most cases, but the
current code uses all of them [1];
- entering CFI mode from autoselect mode and then exiting CFI mode should
return the chip to autoselect mode, but the current code returns to read
array mode; and
- reset command should be ignored during sector/chip erase, but the current
code performs the reset.
The first patch in the series adds a test for the existing behavior. Tests for
additional behavior/bug fixes are added in the relevant patch.
1. I found firmware in the wild that relies on the 11-bit address behavior,
probably due to a bug in the firmware itself.
Changes from v1:
- Fix missing spaces around *, -, and ?.
- Fix missing Signed-off-by line on patch 7
- Replace use of errc with g_printerr and exit
Stephen Checkoway (10):
block/pflash_cfi02: Add test for supported commands
block/pflash_cfi02: Refactor, NFC intended
block/pflash_cfi02: Fix command address comparison
block/pflash_cfi02: Implement intereleaved flash devices
block/pflash_cfi02: Implement nonuniform sector sizes
block/pflash_cfi02: Fix CFI in autoselect mode
block/pflash_cfi02: Fix reset command not ignored during erase
block/pflash_cfi02: Implement multi-sector erase
block/pflash_cfi02: Implement erase suspend/resume
block/pflash_cfi02: Use the chip erase time specified in the CFI table
hw/block/pflash_cfi02.c | 843 +++++++++++++++++++++++++++-----------
tests/Makefile.include | 2 +
tests/pflash-cfi02-test.c | 759 ++++++++++++++++++++++++++++++++++
3 files changed, 1367 insertions(+), 237 deletions(-)
create mode 100644 tests/pflash-cfi02-test.c
--
2.20.1 (Apple Git-117)
^ permalink raw reply [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 01/10] block/pflash_cfi02: Add test for supported commands
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 02/10] block/pflash_cfi02: Refactor, NFC intended Stephen Checkoway
` (8 subsequent siblings)
10 siblings, 1 reply; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Max Reitz, qemu-block, Stephen Checkoway, Thomas Huth,
Laurent Vivier, Paolo Bonzini
Test the AMD command set for parallel flash chips. This test uses an
ARM musicpal board with a pflash drive to test the following list of
currently-supported commands.
- Autoselect
- CFI
- Sector erase
- Chip erase
- Program
- Unlock bypass
- Reset
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
tests/Makefile.include | 2 +
tests/pflash-cfi02-test.c | 227 ++++++++++++++++++++++++++++++++++++++
2 files changed, 229 insertions(+)
create mode 100644 tests/pflash-cfi02-test.c
diff --git a/tests/Makefile.include b/tests/Makefile.include
index 6b904d7430..0a26eacce0 100644
--- a/tests/Makefile.include
+++ b/tests/Makefile.include
@@ -263,6 +263,7 @@ check-qtest-arm-y += tests/m25p80-test$(EXESUF)
check-qtest-arm-y += tests/test-arm-mptimer$(EXESUF)
check-qtest-arm-y += tests/boot-serial-test$(EXESUF)
check-qtest-arm-y += tests/hexloader-test$(EXESUF)
+check-qtest-arm-$(CONFIG_PFLASH_CFI02) += tests/pflash-cfi02-test$(EXESUF)
check-qtest-aarch64-y = tests/numa-test$(EXESUF)
check-qtest-aarch64-y += tests/boot-serial-test$(EXESUF)
@@ -773,6 +774,7 @@ tests/device-introspect-test$(EXESUF): tests/device-introspect-test.o
tests/rtc-test$(EXESUF): tests/rtc-test.o
tests/m48t59-test$(EXESUF): tests/m48t59-test.o
tests/hexloader-test$(EXESUF): tests/hexloader-test.o
+tests/pflash-cfi02$(EXESUF): tests/pflash-cfi02-test.o
tests/endianness-test$(EXESUF): tests/endianness-test.o
tests/prom-env-test$(EXESUF): tests/prom-env-test.o $(libqos-obj-y)
tests/rtas-test$(EXESUF): tests/rtas-test.o $(libqos-spapr-obj-y)
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
new file mode 100644
index 0000000000..b113fca5af
--- /dev/null
+++ b/tests/pflash-cfi02-test.c
@@ -0,0 +1,227 @@
+/*
+ * QTest testcase for parallel flash with AMD command set
+ *
+ * Copyright (c) 2018 Stephen Checkoway
+ *
+ * This work is licensed under the terms of the GNU GPL, version 2 or later.
+ * See the COPYING file in the top-level directory.
+ */
+
+#include "qemu/osdep.h"
+#include <err.h>
+#include <unistd.h>
+#include "libqtest.h"
+
+/*
+ * To test the pflash_cfi02 device, we run QEMU with the musicpal machine with
+ * a pflash drive. This enables us to test some flash configurations, but not
+ * all. In particular, we're limited to a 16-bit wide flash device.
+ */
+
+#define MP_FLASH_SIZE_MAX (32 * 1024 * 1024)
+#define BASE_ADDR (0x100000000ULL - MP_FLASH_SIZE_MAX)
+
+#define FLASH_WIDTH 2
+#define CFI_ADDR (FLASH_WIDTH * 0x55)
+#define UNLOCK0_ADDR (FLASH_WIDTH * 0x5555)
+#define UNLOCK1_ADDR (FLASH_WIDTH * 0x2AAA)
+
+#define CFI_CMD 0x98
+#define UNLOCK0_CMD 0xAA
+#define UNLOCK1_CMD 0x55
+#define AUTOSELECT_CMD 0x90
+#define RESET_CMD 0xF0
+#define PROGRAM_CMD 0xA0
+#define SECTOR_ERASE_CMD 0x30
+#define CHIP_ERASE_CMD 0x10
+#define UNLOCK_BYPASS_CMD 0x20
+#define UNLOCK_BYPASS_RESET_CMD 0x00
+
+static char image_path[] = "/tmp/qtest.XXXXXX";
+
+static inline void flash_write(uint64_t byte_addr, uint16_t data)
+{
+ qtest_writew(global_qtest, BASE_ADDR + byte_addr, data);
+}
+
+static inline uint16_t flash_read(uint64_t byte_addr)
+{
+ return qtest_readw(global_qtest, BASE_ADDR + byte_addr);
+}
+
+static void unlock(void)
+{
+ flash_write(UNLOCK0_ADDR, UNLOCK0_CMD);
+ flash_write(UNLOCK1_ADDR, UNLOCK1_CMD);
+}
+
+static void reset(void)
+{
+ flash_write(0, RESET_CMD);
+}
+
+static void sector_erase(uint64_t byte_addr)
+{
+ unlock();
+ flash_write(UNLOCK0_ADDR, 0x80);
+ unlock();
+ flash_write(byte_addr, SECTOR_ERASE_CMD);
+}
+
+static void wait_for_completion(uint64_t byte_addr)
+{
+ /* If DQ6 is toggling, step the clock and ensure the toggle stops. */
+ if ((flash_read(byte_addr) & 0x40) ^ (flash_read(byte_addr) & 0x40)) {
+ /* Wait for erase or program to finish. */
+ clock_step_next();
+ /* Ensure that DQ6 has stopped toggling. */
+ g_assert_cmpint(flash_read(byte_addr), ==, flash_read(byte_addr));
+ }
+}
+
+static void bypass_program(uint64_t byte_addr, uint16_t data)
+{
+ flash_write(UNLOCK0_ADDR, PROGRAM_CMD);
+ flash_write(byte_addr, data);
+ /*
+ * Data isn't valid until DQ6 stops toggling. We don't model this as
+ * writes are immediate, but if this changes in the future, we can wait
+ * until the program is complete.
+ */
+ wait_for_completion(byte_addr);
+}
+
+static void program(uint64_t byte_addr, uint16_t data)
+{
+ unlock();
+ bypass_program(byte_addr, data);
+}
+
+static void chip_erase(void)
+{
+ unlock();
+ flash_write(UNLOCK0_ADDR, 0x80);
+ unlock();
+ flash_write(UNLOCK0_ADDR, SECTOR_ERASE_CMD);
+}
+
+static void test_flash(void)
+{
+ global_qtest = qtest_initf("-M musicpal,accel=qtest "
+ "-drive if=pflash,file=%s,format=raw,copy-on-read",
+ image_path);
+ /* Check the IDs. */
+ unlock();
+ flash_write(UNLOCK0_ADDR, AUTOSELECT_CMD);
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0000), ==, 0x00BF);
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0001), ==, 0x236D);
+ reset();
+
+ /* Check the erase blocks. */
+ flash_write(CFI_ADDR, CFI_CMD);
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x10), ==, 'Q');
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x11), ==, 'R');
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x12), ==, 'Y');
+ /* Num erase regions. */
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x2C), >=, 1);
+ uint32_t nb_sectors = flash_read(FLASH_WIDTH * 0x2D) +
+ (flash_read(FLASH_WIDTH * 0x2E) << 8) + 1;
+ uint32_t sector_len = (flash_read(FLASH_WIDTH * 0x2F) << 8) +
+ (flash_read(FLASH_WIDTH * 0x30) << 16);
+ reset();
+
+ /* Erase and program sector. */
+ for (uint32_t i = 0; i < nb_sectors; ++i) {
+ uint64_t byte_addr = i * sector_len;
+ sector_erase(byte_addr);
+ /* Read toggle. */
+ uint16_t status0 = flash_read(byte_addr);
+ /* DQ7 is 0 during an erase. */
+ g_assert_cmpint(status0 & 0x80, ==, 0);
+ uint16_t status1 = flash_read(byte_addr);
+ /* DQ6 toggles during an erase. */
+ g_assert_cmpint(status0 & 0x40, !=, status1 & 0x40);
+ /* Wait for erase to complete. */
+ clock_step_next();
+ /* Ensure DQ6 has stopped toggling. */
+ g_assert_cmpint(flash_read(byte_addr), ==, flash_read(byte_addr));
+ /* Now the data should be valid. */
+ g_assert_cmpint(flash_read(byte_addr), ==, 0xFFFF);
+
+ /* Program a bit pattern. */
+ program(byte_addr, 0x5555);
+ g_assert_cmpint(flash_read(byte_addr), ==, 0x5555);
+ program(byte_addr, 0xAA55);
+ g_assert_cmpint(flash_read(byte_addr), ==, 0x0055);
+ }
+
+ /* Erase the chip. */
+ chip_erase();
+ /* Read toggle. */
+ uint16_t status0 = flash_read(0);
+ /* DQ7 is 0 during an erase. */
+ g_assert_cmpint(status0 & 0x80, ==, 0);
+ uint16_t status1 = flash_read(0);
+ /* DQ6 toggles during an erase. */
+ g_assert_cmpint(status0 & 0x40, !=, status1 & 0x40);
+ /* Wait for erase to complete. */
+ clock_step_next();
+ /* Ensure DQ6 has stopped toggling. */
+ g_assert_cmpint(flash_read(0), ==, flash_read(0));
+ /* Now the data should be valid. */
+ g_assert_cmpint(flash_read(0), ==, 0xFFFF);
+
+ /* Unlock bypass */
+ unlock();
+ flash_write(UNLOCK0_ADDR, UNLOCK_BYPASS_CMD);
+ bypass_program(0, 0x0123);
+ bypass_program(2, 0x4567);
+ bypass_program(4, 0x89AB);
+ /*
+ * Test that bypass programming, unlike normal programming can use any
+ * address for the PROGRAM_CMD.
+ */
+ flash_write(6, PROGRAM_CMD);
+ flash_write(6, 0xCDEF);
+ wait_for_completion(6);
+ flash_write(0, UNLOCK_BYPASS_RESET_CMD);
+ bypass_program(8, 0x55AA); /* Should fail. */
+ g_assert_cmpint(flash_read(0), ==, 0x0123);
+ g_assert_cmpint(flash_read(2), ==, 0x4567);
+ g_assert_cmpint(flash_read(4), ==, 0x89AB);
+ g_assert_cmpint(flash_read(6), ==, 0xCDEF);
+ g_assert_cmpint(flash_read(8), ==, 0xFFFF);
+
+ qtest_quit(global_qtest);
+}
+
+static void cleanup(void *opaque)
+{
+ unlink(image_path);
+}
+
+int main(int argc, char **argv)
+{
+ int fd = mkstemp(image_path);
+ if (fd == -1) {
+ err(1, "Failed to create temporary file %s", image_path);
+ }
+ if (ftruncate(fd, 8 * 1024 * 1024) < 0) {
+ int error_code = errno;
+ close(fd);
+ unlink(image_path);
+ g_printerr("Failed to truncate file %s to 8 MB: %s\n", image_path,
+ strerror(error_code));
+ exit(EXIT_FAILURE);
+ }
+ close(fd);
+
+ qtest_add_abrt_handler(cleanup, NULL);
+ g_test_init(&argc, &argv, NULL);
+ qtest_add_func("pflash-cfi02", test_flash);
+ int result = g_test_run();
+ cleanup(NULL);
+ return result;
+}
+
+/* vim: set sw=4 sts=4 ts=8 et: */
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 01/10] block/pflash_cfi02: Add test for supported commands
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 01/10] block/pflash_cfi02: Add test for supported commands Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
0 siblings, 0 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Laurent Vivier, Thomas Huth, Stephen Checkoway,
qemu-block, Max Reitz, Paolo Bonzini
Test the AMD command set for parallel flash chips. This test uses an
ARM musicpal board with a pflash drive to test the following list of
currently-supported commands.
- Autoselect
- CFI
- Sector erase
- Chip erase
- Program
- Unlock bypass
- Reset
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
tests/Makefile.include | 2 +
tests/pflash-cfi02-test.c | 227 ++++++++++++++++++++++++++++++++++++++
2 files changed, 229 insertions(+)
create mode 100644 tests/pflash-cfi02-test.c
diff --git a/tests/Makefile.include b/tests/Makefile.include
index 6b904d7430..0a26eacce0 100644
--- a/tests/Makefile.include
+++ b/tests/Makefile.include
@@ -263,6 +263,7 @@ check-qtest-arm-y += tests/m25p80-test$(EXESUF)
check-qtest-arm-y += tests/test-arm-mptimer$(EXESUF)
check-qtest-arm-y += tests/boot-serial-test$(EXESUF)
check-qtest-arm-y += tests/hexloader-test$(EXESUF)
+check-qtest-arm-$(CONFIG_PFLASH_CFI02) += tests/pflash-cfi02-test$(EXESUF)
check-qtest-aarch64-y = tests/numa-test$(EXESUF)
check-qtest-aarch64-y += tests/boot-serial-test$(EXESUF)
@@ -773,6 +774,7 @@ tests/device-introspect-test$(EXESUF): tests/device-introspect-test.o
tests/rtc-test$(EXESUF): tests/rtc-test.o
tests/m48t59-test$(EXESUF): tests/m48t59-test.o
tests/hexloader-test$(EXESUF): tests/hexloader-test.o
+tests/pflash-cfi02$(EXESUF): tests/pflash-cfi02-test.o
tests/endianness-test$(EXESUF): tests/endianness-test.o
tests/prom-env-test$(EXESUF): tests/prom-env-test.o $(libqos-obj-y)
tests/rtas-test$(EXESUF): tests/rtas-test.o $(libqos-spapr-obj-y)
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
new file mode 100644
index 0000000000..b113fca5af
--- /dev/null
+++ b/tests/pflash-cfi02-test.c
@@ -0,0 +1,227 @@
+/*
+ * QTest testcase for parallel flash with AMD command set
+ *
+ * Copyright (c) 2018 Stephen Checkoway
+ *
+ * This work is licensed under the terms of the GNU GPL, version 2 or later.
+ * See the COPYING file in the top-level directory.
+ */
+
+#include "qemu/osdep.h"
+#include <err.h>
+#include <unistd.h>
+#include "libqtest.h"
+
+/*
+ * To test the pflash_cfi02 device, we run QEMU with the musicpal machine with
+ * a pflash drive. This enables us to test some flash configurations, but not
+ * all. In particular, we're limited to a 16-bit wide flash device.
+ */
+
+#define MP_FLASH_SIZE_MAX (32 * 1024 * 1024)
+#define BASE_ADDR (0x100000000ULL - MP_FLASH_SIZE_MAX)
+
+#define FLASH_WIDTH 2
+#define CFI_ADDR (FLASH_WIDTH * 0x55)
+#define UNLOCK0_ADDR (FLASH_WIDTH * 0x5555)
+#define UNLOCK1_ADDR (FLASH_WIDTH * 0x2AAA)
+
+#define CFI_CMD 0x98
+#define UNLOCK0_CMD 0xAA
+#define UNLOCK1_CMD 0x55
+#define AUTOSELECT_CMD 0x90
+#define RESET_CMD 0xF0
+#define PROGRAM_CMD 0xA0
+#define SECTOR_ERASE_CMD 0x30
+#define CHIP_ERASE_CMD 0x10
+#define UNLOCK_BYPASS_CMD 0x20
+#define UNLOCK_BYPASS_RESET_CMD 0x00
+
+static char image_path[] = "/tmp/qtest.XXXXXX";
+
+static inline void flash_write(uint64_t byte_addr, uint16_t data)
+{
+ qtest_writew(global_qtest, BASE_ADDR + byte_addr, data);
+}
+
+static inline uint16_t flash_read(uint64_t byte_addr)
+{
+ return qtest_readw(global_qtest, BASE_ADDR + byte_addr);
+}
+
+static void unlock(void)
+{
+ flash_write(UNLOCK0_ADDR, UNLOCK0_CMD);
+ flash_write(UNLOCK1_ADDR, UNLOCK1_CMD);
+}
+
+static void reset(void)
+{
+ flash_write(0, RESET_CMD);
+}
+
+static void sector_erase(uint64_t byte_addr)
+{
+ unlock();
+ flash_write(UNLOCK0_ADDR, 0x80);
+ unlock();
+ flash_write(byte_addr, SECTOR_ERASE_CMD);
+}
+
+static void wait_for_completion(uint64_t byte_addr)
+{
+ /* If DQ6 is toggling, step the clock and ensure the toggle stops. */
+ if ((flash_read(byte_addr) & 0x40) ^ (flash_read(byte_addr) & 0x40)) {
+ /* Wait for erase or program to finish. */
+ clock_step_next();
+ /* Ensure that DQ6 has stopped toggling. */
+ g_assert_cmpint(flash_read(byte_addr), ==, flash_read(byte_addr));
+ }
+}
+
+static void bypass_program(uint64_t byte_addr, uint16_t data)
+{
+ flash_write(UNLOCK0_ADDR, PROGRAM_CMD);
+ flash_write(byte_addr, data);
+ /*
+ * Data isn't valid until DQ6 stops toggling. We don't model this as
+ * writes are immediate, but if this changes in the future, we can wait
+ * until the program is complete.
+ */
+ wait_for_completion(byte_addr);
+}
+
+static void program(uint64_t byte_addr, uint16_t data)
+{
+ unlock();
+ bypass_program(byte_addr, data);
+}
+
+static void chip_erase(void)
+{
+ unlock();
+ flash_write(UNLOCK0_ADDR, 0x80);
+ unlock();
+ flash_write(UNLOCK0_ADDR, SECTOR_ERASE_CMD);
+}
+
+static void test_flash(void)
+{
+ global_qtest = qtest_initf("-M musicpal,accel=qtest "
+ "-drive if=pflash,file=%s,format=raw,copy-on-read",
+ image_path);
+ /* Check the IDs. */
+ unlock();
+ flash_write(UNLOCK0_ADDR, AUTOSELECT_CMD);
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0000), ==, 0x00BF);
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0001), ==, 0x236D);
+ reset();
+
+ /* Check the erase blocks. */
+ flash_write(CFI_ADDR, CFI_CMD);
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x10), ==, 'Q');
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x11), ==, 'R');
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x12), ==, 'Y');
+ /* Num erase regions. */
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x2C), >=, 1);
+ uint32_t nb_sectors = flash_read(FLASH_WIDTH * 0x2D) +
+ (flash_read(FLASH_WIDTH * 0x2E) << 8) + 1;
+ uint32_t sector_len = (flash_read(FLASH_WIDTH * 0x2F) << 8) +
+ (flash_read(FLASH_WIDTH * 0x30) << 16);
+ reset();
+
+ /* Erase and program sector. */
+ for (uint32_t i = 0; i < nb_sectors; ++i) {
+ uint64_t byte_addr = i * sector_len;
+ sector_erase(byte_addr);
+ /* Read toggle. */
+ uint16_t status0 = flash_read(byte_addr);
+ /* DQ7 is 0 during an erase. */
+ g_assert_cmpint(status0 & 0x80, ==, 0);
+ uint16_t status1 = flash_read(byte_addr);
+ /* DQ6 toggles during an erase. */
+ g_assert_cmpint(status0 & 0x40, !=, status1 & 0x40);
+ /* Wait for erase to complete. */
+ clock_step_next();
+ /* Ensure DQ6 has stopped toggling. */
+ g_assert_cmpint(flash_read(byte_addr), ==, flash_read(byte_addr));
+ /* Now the data should be valid. */
+ g_assert_cmpint(flash_read(byte_addr), ==, 0xFFFF);
+
+ /* Program a bit pattern. */
+ program(byte_addr, 0x5555);
+ g_assert_cmpint(flash_read(byte_addr), ==, 0x5555);
+ program(byte_addr, 0xAA55);
+ g_assert_cmpint(flash_read(byte_addr), ==, 0x0055);
+ }
+
+ /* Erase the chip. */
+ chip_erase();
+ /* Read toggle. */
+ uint16_t status0 = flash_read(0);
+ /* DQ7 is 0 during an erase. */
+ g_assert_cmpint(status0 & 0x80, ==, 0);
+ uint16_t status1 = flash_read(0);
+ /* DQ6 toggles during an erase. */
+ g_assert_cmpint(status0 & 0x40, !=, status1 & 0x40);
+ /* Wait for erase to complete. */
+ clock_step_next();
+ /* Ensure DQ6 has stopped toggling. */
+ g_assert_cmpint(flash_read(0), ==, flash_read(0));
+ /* Now the data should be valid. */
+ g_assert_cmpint(flash_read(0), ==, 0xFFFF);
+
+ /* Unlock bypass */
+ unlock();
+ flash_write(UNLOCK0_ADDR, UNLOCK_BYPASS_CMD);
+ bypass_program(0, 0x0123);
+ bypass_program(2, 0x4567);
+ bypass_program(4, 0x89AB);
+ /*
+ * Test that bypass programming, unlike normal programming can use any
+ * address for the PROGRAM_CMD.
+ */
+ flash_write(6, PROGRAM_CMD);
+ flash_write(6, 0xCDEF);
+ wait_for_completion(6);
+ flash_write(0, UNLOCK_BYPASS_RESET_CMD);
+ bypass_program(8, 0x55AA); /* Should fail. */
+ g_assert_cmpint(flash_read(0), ==, 0x0123);
+ g_assert_cmpint(flash_read(2), ==, 0x4567);
+ g_assert_cmpint(flash_read(4), ==, 0x89AB);
+ g_assert_cmpint(flash_read(6), ==, 0xCDEF);
+ g_assert_cmpint(flash_read(8), ==, 0xFFFF);
+
+ qtest_quit(global_qtest);
+}
+
+static void cleanup(void *opaque)
+{
+ unlink(image_path);
+}
+
+int main(int argc, char **argv)
+{
+ int fd = mkstemp(image_path);
+ if (fd == -1) {
+ err(1, "Failed to create temporary file %s", image_path);
+ }
+ if (ftruncate(fd, 8 * 1024 * 1024) < 0) {
+ int error_code = errno;
+ close(fd);
+ unlink(image_path);
+ g_printerr("Failed to truncate file %s to 8 MB: %s\n", image_path,
+ strerror(error_code));
+ exit(EXIT_FAILURE);
+ }
+ close(fd);
+
+ qtest_add_abrt_handler(cleanup, NULL);
+ g_test_init(&argc, &argv, NULL);
+ qtest_add_func("pflash-cfi02", test_flash);
+ int result = g_test_run();
+ cleanup(NULL);
+ return result;
+}
+
+/* vim: set sw=4 sts=4 ts=8 et: */
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 02/10] block/pflash_cfi02: Refactor, NFC intended
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 01/10] block/pflash_cfi02: Add test for supported commands Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 03/10] block/pflash_cfi02: Fix command address comparison Stephen Checkoway
` (7 subsequent siblings)
10 siblings, 1 reply; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel; +Cc: Kevin Wolf, Max Reitz, qemu-block, Stephen Checkoway
Simplify and refactor for upcoming commits. In particular, pull out all
of the code to modify the status into simple helper functions. Status
handling becomes more complex once multiple chips are interleaved to
produce a single device.
No change in functionality is intended with this commit.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 221 +++++++++++++++++-----------------------
1 file changed, 95 insertions(+), 126 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index f2c6201f81..4b7af71806 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -46,18 +46,19 @@
#include "hw/sysbus.h"
#include "trace.h"
-//#define PFLASH_DEBUG
-#ifdef PFLASH_DEBUG
+#define PFLASH_DEBUG false
#define DPRINTF(fmt, ...) \
do { \
- fprintf(stderr, "PFLASH: " fmt , ## __VA_ARGS__); \
+ if (PFLASH_DEBUG) { \
+ fprintf(stderr, "PFLASH: " fmt, ## __VA_ARGS__); \
+ } \
} while (0)
-#else
-#define DPRINTF(fmt, ...) do { } while (0)
-#endif
#define PFLASH_LAZY_ROMD_THRESHOLD 42
+/* Special write cycle for CFI queries. */
+#define WCYCLE_CFI 7
+
struct PFlashCFI02 {
/*< private >*/
SysBusDevice parent_obj;
@@ -97,6 +98,31 @@ struct PFlashCFI02 {
void *storage;
};
+/*
+ * Toggle status bit DQ7.
+ */
+static inline void toggle_dq7(PFlashCFI02 *pfl)
+{
+ pfl->status ^= 0x80;
+}
+
+/*
+ * Set status bit DQ7 to bit 7 of value.
+ */
+static inline void set_dq7(PFlashCFI02 *pfl, uint8_t value)
+{
+ pfl->status &= 0x7F;
+ pfl->status |= value & 0x80;
+}
+
+/*
+ * Toggle status bit DQ6.
+ */
+static inline void toggle_dq6(PFlashCFI02 *pfl)
+{
+ pfl->status ^= 0x40;
+}
+
/*
* Set up replicated mappings of the same region.
*/
@@ -126,7 +152,7 @@ static void pflash_timer (void *opaque)
trace_pflash_timer_expired(pfl->cmd);
/* Reset flash */
- pfl->status ^= 0x80;
+ toggle_dq7(pfl);
if (pfl->bypass) {
pfl->wcycle = 2;
} else {
@@ -136,12 +162,34 @@ static void pflash_timer (void *opaque)
pfl->cmd = 0;
}
-static uint32_t pflash_read(PFlashCFI02 *pfl, hwaddr offset,
- int width, int be)
+/*
+ * Read data from flash.
+ */
+static uint64_t pflash_data_read(PFlashCFI02 *pfl, hwaddr offset,
+ unsigned int width)
{
+ uint8_t *p = (uint8_t *)pfl->storage + offset;
+ uint64_t ret = pfl->be ? ldn_be_p(p, width) : ldn_le_p(p, width);
+ /* XXX: Need a trace_pflash_data_read(offset, ret, width) */
+ switch (width) {
+ case 1:
+ trace_pflash_data_read8(offset, ret);
+ break;
+ case 2:
+ trace_pflash_data_read16(offset, ret);
+ break;
+ case 4:
+ trace_pflash_data_read32(offset, ret);
+ break;
+ }
+ return ret;
+}
+
+static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
+{
+ PFlashCFI02 *pfl = opaque;
hwaddr boff;
- uint32_t ret;
- uint8_t *p;
+ uint64_t ret;
ret = -1;
trace_pflash_read(offset, pfl->cmd, width, pfl->wcycle);
@@ -166,39 +214,8 @@ static uint32_t pflash_read(PFlashCFI02 *pfl, hwaddr offset,
case 0x80:
/* We accept reads during second unlock sequence... */
case 0x00:
- flash_read:
/* Flash area read */
- p = pfl->storage;
- switch (width) {
- case 1:
- ret = p[offset];
- trace_pflash_data_read8(offset, ret);
- break;
- case 2:
- if (be) {
- ret = p[offset] << 8;
- ret |= p[offset + 1];
- } else {
- ret = p[offset];
- ret |= p[offset + 1] << 8;
- }
- trace_pflash_data_read16(offset, ret);
- break;
- case 4:
- if (be) {
- ret = p[offset] << 24;
- ret |= p[offset + 1] << 16;
- ret |= p[offset + 2] << 8;
- ret |= p[offset + 3];
- } else {
- ret = p[offset];
- ret |= p[offset + 1] << 8;
- ret |= p[offset + 2] << 16;
- ret |= p[offset + 3] << 24;
- }
- trace_pflash_data_read32(offset, ret);
- break;
- }
+ ret = pflash_data_read(pfl, offset, width);
break;
case 0x90:
/* flash ID read */
@@ -213,23 +230,23 @@ static uint32_t pflash_read(PFlashCFI02 *pfl, hwaddr offset,
case 0x0E:
case 0x0F:
ret = boff & 0x01 ? pfl->ident3 : pfl->ident2;
- if (ret == (uint8_t)-1) {
- goto flash_read;
+ if (ret != (uint8_t)-1) {
+ break;
}
- break;
+ /* Fall through to data read. */
default:
- goto flash_read;
+ ret = pflash_data_read(pfl, offset, width);
}
- DPRINTF("%s: ID " TARGET_FMT_plx " %x\n", __func__, boff, ret);
+ DPRINTF("%s: ID " TARGET_FMT_plx " %" PRIx64 "\n", __func__, boff, ret);
break;
case 0xA0:
case 0x10:
case 0x30:
/* Status register read */
ret = pfl->status;
- DPRINTF("%s: status %x\n", __func__, ret);
+ DPRINTF("%s: status %" PRIx64 "\n", __func__, ret);
/* Toggle bit 6 */
- pfl->status ^= 0x40;
+ toggle_dq6(pfl);
break;
case 0x98:
/* CFI query mode */
@@ -245,8 +262,7 @@ static uint32_t pflash_read(PFlashCFI02 *pfl, hwaddr offset,
}
/* update flash content on disk */
-static void pflash_update(PFlashCFI02 *pfl, int offset,
- int size)
+static void pflash_update(PFlashCFI02 *pfl, int offset, int size)
{
int offset_end;
if (pfl->blk) {
@@ -259,9 +275,10 @@ static void pflash_update(PFlashCFI02 *pfl, int offset,
}
}
-static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
- uint32_t value, int width, int be)
+static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
+ unsigned int width)
{
+ PFlashCFI02 *pfl = opaque;
hwaddr boff;
uint8_t *p;
uint8_t cmd;
@@ -277,7 +294,7 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
trace_pflash_write(offset, value, width, pfl->wcycle);
offset &= pfl->chip_len - 1;
- DPRINTF("%s: offset " TARGET_FMT_plx " %08x %d\n", __func__,
+ DPRINTF("%s: offset " TARGET_FMT_plx " %08" PRIx64 " %d\n", __func__,
offset, value, width);
boff = offset & (pfl->sector_len - 1);
if (pfl->width == 2)
@@ -295,7 +312,7 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
if (boff == 0x55 && cmd == 0x98) {
enter_CFI_mode:
/* Enter CFI query mode */
- pfl->wcycle = 7;
+ pfl->wcycle = WCYCLE_CFI;
pfl->cmd = 0x98;
return;
}
@@ -345,40 +362,22 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
goto check_unlock0;
case 0xA0:
trace_pflash_data_write(offset, value, width, 0);
- p = pfl->storage;
if (!pfl->ro) {
- switch (width) {
- case 1:
- p[offset] &= value;
- pflash_update(pfl, offset, 1);
- break;
- case 2:
- if (be) {
- p[offset] &= value >> 8;
- p[offset + 1] &= value;
- } else {
- p[offset] &= value;
- p[offset + 1] &= value >> 8;
- }
- pflash_update(pfl, offset, 2);
- break;
- case 4:
- if (be) {
- p[offset] &= value >> 24;
- p[offset + 1] &= value >> 16;
- p[offset + 2] &= value >> 8;
- p[offset + 3] &= value;
- } else {
- p[offset] &= value;
- p[offset + 1] &= value >> 8;
- p[offset + 2] &= value >> 16;
- p[offset + 3] &= value >> 24;
- }
- pflash_update(pfl, offset, 4);
- break;
+ p = (uint8_t *)pfl->storage + offset;
+ if (pfl->be) {
+ uint64_t current = ldn_be_p(p, width);
+ stn_be_p(p, width, current & value);
+ } else {
+ uint64_t current = ldn_le_p(p, width);
+ stn_le_p(p, width, current & value);
}
+ pflash_update(pfl, offset, width);
}
- pfl->status = 0x00 | ~(value & 0x80);
+ /*
+ * While programming, status bit DQ7 should hold the opposite
+ * value from how it was programmed.
+ */
+ set_dq7(pfl, ~value);
/* Let's pretend write is immediate */
if (pfl->bypass)
goto do_bypass;
@@ -426,7 +425,7 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
memset(pfl->storage, 0xFF, pfl->chip_len);
pflash_update(pfl, 0, pfl->chip_len);
}
- pfl->status = 0x00;
+ set_dq7(pfl, 0x00);
/* Let's wait 5 seconds before chip erase is done */
timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) +
(NANOSECONDS_PER_SECOND * 5));
@@ -441,7 +440,7 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
memset(p + offset, 0xFF, pfl->sector_len);
pflash_update(pfl, offset, pfl->sector_len);
}
- pfl->status = 0x00;
+ set_dq7(pfl, 0x00);
/* Let's wait 1/2 second before sector erase is done */
timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) +
(NANOSECONDS_PER_SECOND / 2));
@@ -467,7 +466,7 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
goto reset_flash;
}
break;
- case 7: /* Special value for CFI queries */
+ case WCYCLE_CFI: /* Special value for CFI queries */
DPRINTF("%s: invalid write in CFI query mode\n", __func__);
goto reset_flash;
default:
@@ -492,39 +491,9 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
pfl->cmd = 0;
}
-static uint64_t pflash_be_readfn(void *opaque, hwaddr addr, unsigned size)
-{
- return pflash_read(opaque, addr, size, 1);
-}
-
-static void pflash_be_writefn(void *opaque, hwaddr addr,
- uint64_t value, unsigned size)
-{
- pflash_write(opaque, addr, value, size, 1);
-}
-
-static uint64_t pflash_le_readfn(void *opaque, hwaddr addr, unsigned size)
-{
- return pflash_read(opaque, addr, size, 0);
-}
-
-static void pflash_le_writefn(void *opaque, hwaddr addr,
- uint64_t value, unsigned size)
-{
- pflash_write(opaque, addr, value, size, 0);
-}
-
-static const MemoryRegionOps pflash_cfi02_ops_be = {
- .read = pflash_be_readfn,
- .write = pflash_be_writefn,
- .valid.min_access_size = 1,
- .valid.max_access_size = 4,
- .endianness = DEVICE_NATIVE_ENDIAN,
-};
-
-static const MemoryRegionOps pflash_cfi02_ops_le = {
- .read = pflash_le_readfn,
- .write = pflash_le_writefn,
+static const MemoryRegionOps pflash_cfi02_ops = {
+ .read = pflash_read,
+ .write = pflash_write,
.valid.min_access_size = 1,
.valid.max_access_size = 4,
.endianness = DEVICE_NATIVE_ENDIAN,
@@ -552,9 +521,9 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
chip_len = pfl->sector_len * pfl->nb_blocs;
- memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl), pfl->be ?
- &pflash_cfi02_ops_be : &pflash_cfi02_ops_le,
- pfl, pfl->name, chip_len, &local_err);
+ memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl),
+ &pflash_cfi02_ops, pfl, pfl->name,
+ chip_len, &local_err);
if (local_err) {
error_propagate(errp, local_err);
return;
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 02/10] block/pflash_cfi02: Refactor, NFC intended
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 02/10] block/pflash_cfi02: Refactor, NFC intended Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
0 siblings, 0 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel; +Cc: Kevin Wolf, Stephen Checkoway, qemu-block, Max Reitz
Simplify and refactor for upcoming commits. In particular, pull out all
of the code to modify the status into simple helper functions. Status
handling becomes more complex once multiple chips are interleaved to
produce a single device.
No change in functionality is intended with this commit.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 221 +++++++++++++++++-----------------------
1 file changed, 95 insertions(+), 126 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index f2c6201f81..4b7af71806 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -46,18 +46,19 @@
#include "hw/sysbus.h"
#include "trace.h"
-//#define PFLASH_DEBUG
-#ifdef PFLASH_DEBUG
+#define PFLASH_DEBUG false
#define DPRINTF(fmt, ...) \
do { \
- fprintf(stderr, "PFLASH: " fmt , ## __VA_ARGS__); \
+ if (PFLASH_DEBUG) { \
+ fprintf(stderr, "PFLASH: " fmt, ## __VA_ARGS__); \
+ } \
} while (0)
-#else
-#define DPRINTF(fmt, ...) do { } while (0)
-#endif
#define PFLASH_LAZY_ROMD_THRESHOLD 42
+/* Special write cycle for CFI queries. */
+#define WCYCLE_CFI 7
+
struct PFlashCFI02 {
/*< private >*/
SysBusDevice parent_obj;
@@ -97,6 +98,31 @@ struct PFlashCFI02 {
void *storage;
};
+/*
+ * Toggle status bit DQ7.
+ */
+static inline void toggle_dq7(PFlashCFI02 *pfl)
+{
+ pfl->status ^= 0x80;
+}
+
+/*
+ * Set status bit DQ7 to bit 7 of value.
+ */
+static inline void set_dq7(PFlashCFI02 *pfl, uint8_t value)
+{
+ pfl->status &= 0x7F;
+ pfl->status |= value & 0x80;
+}
+
+/*
+ * Toggle status bit DQ6.
+ */
+static inline void toggle_dq6(PFlashCFI02 *pfl)
+{
+ pfl->status ^= 0x40;
+}
+
/*
* Set up replicated mappings of the same region.
*/
@@ -126,7 +152,7 @@ static void pflash_timer (void *opaque)
trace_pflash_timer_expired(pfl->cmd);
/* Reset flash */
- pfl->status ^= 0x80;
+ toggle_dq7(pfl);
if (pfl->bypass) {
pfl->wcycle = 2;
} else {
@@ -136,12 +162,34 @@ static void pflash_timer (void *opaque)
pfl->cmd = 0;
}
-static uint32_t pflash_read(PFlashCFI02 *pfl, hwaddr offset,
- int width, int be)
+/*
+ * Read data from flash.
+ */
+static uint64_t pflash_data_read(PFlashCFI02 *pfl, hwaddr offset,
+ unsigned int width)
{
+ uint8_t *p = (uint8_t *)pfl->storage + offset;
+ uint64_t ret = pfl->be ? ldn_be_p(p, width) : ldn_le_p(p, width);
+ /* XXX: Need a trace_pflash_data_read(offset, ret, width) */
+ switch (width) {
+ case 1:
+ trace_pflash_data_read8(offset, ret);
+ break;
+ case 2:
+ trace_pflash_data_read16(offset, ret);
+ break;
+ case 4:
+ trace_pflash_data_read32(offset, ret);
+ break;
+ }
+ return ret;
+}
+
+static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
+{
+ PFlashCFI02 *pfl = opaque;
hwaddr boff;
- uint32_t ret;
- uint8_t *p;
+ uint64_t ret;
ret = -1;
trace_pflash_read(offset, pfl->cmd, width, pfl->wcycle);
@@ -166,39 +214,8 @@ static uint32_t pflash_read(PFlashCFI02 *pfl, hwaddr offset,
case 0x80:
/* We accept reads during second unlock sequence... */
case 0x00:
- flash_read:
/* Flash area read */
- p = pfl->storage;
- switch (width) {
- case 1:
- ret = p[offset];
- trace_pflash_data_read8(offset, ret);
- break;
- case 2:
- if (be) {
- ret = p[offset] << 8;
- ret |= p[offset + 1];
- } else {
- ret = p[offset];
- ret |= p[offset + 1] << 8;
- }
- trace_pflash_data_read16(offset, ret);
- break;
- case 4:
- if (be) {
- ret = p[offset] << 24;
- ret |= p[offset + 1] << 16;
- ret |= p[offset + 2] << 8;
- ret |= p[offset + 3];
- } else {
- ret = p[offset];
- ret |= p[offset + 1] << 8;
- ret |= p[offset + 2] << 16;
- ret |= p[offset + 3] << 24;
- }
- trace_pflash_data_read32(offset, ret);
- break;
- }
+ ret = pflash_data_read(pfl, offset, width);
break;
case 0x90:
/* flash ID read */
@@ -213,23 +230,23 @@ static uint32_t pflash_read(PFlashCFI02 *pfl, hwaddr offset,
case 0x0E:
case 0x0F:
ret = boff & 0x01 ? pfl->ident3 : pfl->ident2;
- if (ret == (uint8_t)-1) {
- goto flash_read;
+ if (ret != (uint8_t)-1) {
+ break;
}
- break;
+ /* Fall through to data read. */
default:
- goto flash_read;
+ ret = pflash_data_read(pfl, offset, width);
}
- DPRINTF("%s: ID " TARGET_FMT_plx " %x\n", __func__, boff, ret);
+ DPRINTF("%s: ID " TARGET_FMT_plx " %" PRIx64 "\n", __func__, boff, ret);
break;
case 0xA0:
case 0x10:
case 0x30:
/* Status register read */
ret = pfl->status;
- DPRINTF("%s: status %x\n", __func__, ret);
+ DPRINTF("%s: status %" PRIx64 "\n", __func__, ret);
/* Toggle bit 6 */
- pfl->status ^= 0x40;
+ toggle_dq6(pfl);
break;
case 0x98:
/* CFI query mode */
@@ -245,8 +262,7 @@ static uint32_t pflash_read(PFlashCFI02 *pfl, hwaddr offset,
}
/* update flash content on disk */
-static void pflash_update(PFlashCFI02 *pfl, int offset,
- int size)
+static void pflash_update(PFlashCFI02 *pfl, int offset, int size)
{
int offset_end;
if (pfl->blk) {
@@ -259,9 +275,10 @@ static void pflash_update(PFlashCFI02 *pfl, int offset,
}
}
-static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
- uint32_t value, int width, int be)
+static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
+ unsigned int width)
{
+ PFlashCFI02 *pfl = opaque;
hwaddr boff;
uint8_t *p;
uint8_t cmd;
@@ -277,7 +294,7 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
trace_pflash_write(offset, value, width, pfl->wcycle);
offset &= pfl->chip_len - 1;
- DPRINTF("%s: offset " TARGET_FMT_plx " %08x %d\n", __func__,
+ DPRINTF("%s: offset " TARGET_FMT_plx " %08" PRIx64 " %d\n", __func__,
offset, value, width);
boff = offset & (pfl->sector_len - 1);
if (pfl->width == 2)
@@ -295,7 +312,7 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
if (boff == 0x55 && cmd == 0x98) {
enter_CFI_mode:
/* Enter CFI query mode */
- pfl->wcycle = 7;
+ pfl->wcycle = WCYCLE_CFI;
pfl->cmd = 0x98;
return;
}
@@ -345,40 +362,22 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
goto check_unlock0;
case 0xA0:
trace_pflash_data_write(offset, value, width, 0);
- p = pfl->storage;
if (!pfl->ro) {
- switch (width) {
- case 1:
- p[offset] &= value;
- pflash_update(pfl, offset, 1);
- break;
- case 2:
- if (be) {
- p[offset] &= value >> 8;
- p[offset + 1] &= value;
- } else {
- p[offset] &= value;
- p[offset + 1] &= value >> 8;
- }
- pflash_update(pfl, offset, 2);
- break;
- case 4:
- if (be) {
- p[offset] &= value >> 24;
- p[offset + 1] &= value >> 16;
- p[offset + 2] &= value >> 8;
- p[offset + 3] &= value;
- } else {
- p[offset] &= value;
- p[offset + 1] &= value >> 8;
- p[offset + 2] &= value >> 16;
- p[offset + 3] &= value >> 24;
- }
- pflash_update(pfl, offset, 4);
- break;
+ p = (uint8_t *)pfl->storage + offset;
+ if (pfl->be) {
+ uint64_t current = ldn_be_p(p, width);
+ stn_be_p(p, width, current & value);
+ } else {
+ uint64_t current = ldn_le_p(p, width);
+ stn_le_p(p, width, current & value);
}
+ pflash_update(pfl, offset, width);
}
- pfl->status = 0x00 | ~(value & 0x80);
+ /*
+ * While programming, status bit DQ7 should hold the opposite
+ * value from how it was programmed.
+ */
+ set_dq7(pfl, ~value);
/* Let's pretend write is immediate */
if (pfl->bypass)
goto do_bypass;
@@ -426,7 +425,7 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
memset(pfl->storage, 0xFF, pfl->chip_len);
pflash_update(pfl, 0, pfl->chip_len);
}
- pfl->status = 0x00;
+ set_dq7(pfl, 0x00);
/* Let's wait 5 seconds before chip erase is done */
timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) +
(NANOSECONDS_PER_SECOND * 5));
@@ -441,7 +440,7 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
memset(p + offset, 0xFF, pfl->sector_len);
pflash_update(pfl, offset, pfl->sector_len);
}
- pfl->status = 0x00;
+ set_dq7(pfl, 0x00);
/* Let's wait 1/2 second before sector erase is done */
timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) +
(NANOSECONDS_PER_SECOND / 2));
@@ -467,7 +466,7 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
goto reset_flash;
}
break;
- case 7: /* Special value for CFI queries */
+ case WCYCLE_CFI: /* Special value for CFI queries */
DPRINTF("%s: invalid write in CFI query mode\n", __func__);
goto reset_flash;
default:
@@ -492,39 +491,9 @@ static void pflash_write(PFlashCFI02 *pfl, hwaddr offset,
pfl->cmd = 0;
}
-static uint64_t pflash_be_readfn(void *opaque, hwaddr addr, unsigned size)
-{
- return pflash_read(opaque, addr, size, 1);
-}
-
-static void pflash_be_writefn(void *opaque, hwaddr addr,
- uint64_t value, unsigned size)
-{
- pflash_write(opaque, addr, value, size, 1);
-}
-
-static uint64_t pflash_le_readfn(void *opaque, hwaddr addr, unsigned size)
-{
- return pflash_read(opaque, addr, size, 0);
-}
-
-static void pflash_le_writefn(void *opaque, hwaddr addr,
- uint64_t value, unsigned size)
-{
- pflash_write(opaque, addr, value, size, 0);
-}
-
-static const MemoryRegionOps pflash_cfi02_ops_be = {
- .read = pflash_be_readfn,
- .write = pflash_be_writefn,
- .valid.min_access_size = 1,
- .valid.max_access_size = 4,
- .endianness = DEVICE_NATIVE_ENDIAN,
-};
-
-static const MemoryRegionOps pflash_cfi02_ops_le = {
- .read = pflash_le_readfn,
- .write = pflash_le_writefn,
+static const MemoryRegionOps pflash_cfi02_ops = {
+ .read = pflash_read,
+ .write = pflash_write,
.valid.min_access_size = 1,
.valid.max_access_size = 4,
.endianness = DEVICE_NATIVE_ENDIAN,
@@ -552,9 +521,9 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
chip_len = pfl->sector_len * pfl->nb_blocs;
- memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl), pfl->be ?
- &pflash_cfi02_ops_be : &pflash_cfi02_ops_le,
- pfl, pfl->name, chip_len, &local_err);
+ memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl),
+ &pflash_cfi02_ops, pfl, pfl->name,
+ chip_len, &local_err);
if (local_err) {
error_propagate(errp, local_err);
return;
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 03/10] block/pflash_cfi02: Fix command address comparison
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
` (2 preceding siblings ...)
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 02/10] block/pflash_cfi02: Refactor, NFC intended Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 04/10] block/pflash_cfi02: Implement intereleaved flash devices Stephen Checkoway
` (6 subsequent siblings)
10 siblings, 1 reply; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Max Reitz, qemu-block, Stephen Checkoway, Thomas Huth,
Laurent Vivier, Paolo Bonzini
Most AMD commands only examine 11 bits of the address. This masks the
addresses used in the comparison to 11 bits. The exceptions are word or
sector addresses which use offset directly rather than the shifted
offset, boff.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 8 +++++++-
tests/pflash-cfi02-test.c | 12 ++++++++++--
2 files changed, 17 insertions(+), 3 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index 4b7af71806..e4bff0c8f8 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -296,11 +296,13 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
DPRINTF("%s: offset " TARGET_FMT_plx " %08" PRIx64 " %d\n", __func__,
offset, value, width);
- boff = offset & (pfl->sector_len - 1);
+ boff = offset;
if (pfl->width == 2)
boff = boff >> 1;
else if (pfl->width == 4)
boff = boff >> 2;
+ /* Only the least-significant 11 bits are used in most cases. */
+ boff &= 0x7FF;
switch (pfl->wcycle) {
case 0:
/* Set the device in I/O access mode if required */
@@ -519,6 +521,10 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
return;
}
+ /* Only 11 bits are used in the comparison. */
+ pfl->unlock_addr0 &= 0x7FF;
+ pfl->unlock_addr1 &= 0x7FF;
+
chip_len = pfl->sector_len * pfl->nb_blocs;
memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl),
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index b113fca5af..b91bb66a79 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -23,8 +23,8 @@
#define FLASH_WIDTH 2
#define CFI_ADDR (FLASH_WIDTH * 0x55)
-#define UNLOCK0_ADDR (FLASH_WIDTH * 0x5555)
-#define UNLOCK1_ADDR (FLASH_WIDTH * 0x2AAA)
+#define UNLOCK0_ADDR (FLASH_WIDTH * 0x555)
+#define UNLOCK1_ADDR (FLASH_WIDTH * 0x2AA)
#define CFI_CMD 0x98
#define UNLOCK0_CMD 0xAA
@@ -192,6 +192,14 @@ static void test_flash(void)
g_assert_cmpint(flash_read(6), ==, 0xCDEF);
g_assert_cmpint(flash_read(8), ==, 0xFFFF);
+ /* Test ignored high order bits of address. */
+ flash_write(FLASH_WIDTH * 0x5555, UNLOCK0_CMD);
+ flash_write(FLASH_WIDTH * 0x2AAA, UNLOCK1_CMD);
+ flash_write(FLASH_WIDTH * 0x5555, AUTOSELECT_CMD);
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0000), ==, 0x00BF);
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0001), ==, 0x236D);
+ reset();
+
qtest_quit(global_qtest);
}
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 03/10] block/pflash_cfi02: Fix command address comparison
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 03/10] block/pflash_cfi02: Fix command address comparison Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
0 siblings, 0 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Laurent Vivier, Thomas Huth, Stephen Checkoway,
qemu-block, Max Reitz, Paolo Bonzini
Most AMD commands only examine 11 bits of the address. This masks the
addresses used in the comparison to 11 bits. The exceptions are word or
sector addresses which use offset directly rather than the shifted
offset, boff.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 8 +++++++-
tests/pflash-cfi02-test.c | 12 ++++++++++--
2 files changed, 17 insertions(+), 3 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index 4b7af71806..e4bff0c8f8 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -296,11 +296,13 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
DPRINTF("%s: offset " TARGET_FMT_plx " %08" PRIx64 " %d\n", __func__,
offset, value, width);
- boff = offset & (pfl->sector_len - 1);
+ boff = offset;
if (pfl->width == 2)
boff = boff >> 1;
else if (pfl->width == 4)
boff = boff >> 2;
+ /* Only the least-significant 11 bits are used in most cases. */
+ boff &= 0x7FF;
switch (pfl->wcycle) {
case 0:
/* Set the device in I/O access mode if required */
@@ -519,6 +521,10 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
return;
}
+ /* Only 11 bits are used in the comparison. */
+ pfl->unlock_addr0 &= 0x7FF;
+ pfl->unlock_addr1 &= 0x7FF;
+
chip_len = pfl->sector_len * pfl->nb_blocs;
memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl),
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index b113fca5af..b91bb66a79 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -23,8 +23,8 @@
#define FLASH_WIDTH 2
#define CFI_ADDR (FLASH_WIDTH * 0x55)
-#define UNLOCK0_ADDR (FLASH_WIDTH * 0x5555)
-#define UNLOCK1_ADDR (FLASH_WIDTH * 0x2AAA)
+#define UNLOCK0_ADDR (FLASH_WIDTH * 0x555)
+#define UNLOCK1_ADDR (FLASH_WIDTH * 0x2AA)
#define CFI_CMD 0x98
#define UNLOCK0_CMD 0xAA
@@ -192,6 +192,14 @@ static void test_flash(void)
g_assert_cmpint(flash_read(6), ==, 0xCDEF);
g_assert_cmpint(flash_read(8), ==, 0xFFFF);
+ /* Test ignored high order bits of address. */
+ flash_write(FLASH_WIDTH * 0x5555, UNLOCK0_CMD);
+ flash_write(FLASH_WIDTH * 0x2AAA, UNLOCK1_CMD);
+ flash_write(FLASH_WIDTH * 0x5555, AUTOSELECT_CMD);
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0000), ==, 0x00BF);
+ g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0001), ==, 0x236D);
+ reset();
+
qtest_quit(global_qtest);
}
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 04/10] block/pflash_cfi02: Implement intereleaved flash devices
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
` (3 preceding siblings ...)
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 03/10] block/pflash_cfi02: Fix command address comparison Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 05/10] block/pflash_cfi02: Implement nonuniform sector sizes Stephen Checkoway
` (5 subsequent siblings)
10 siblings, 1 reply; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Max Reitz, qemu-block, Stephen Checkoway, Thomas Huth,
Laurent Vivier, Paolo Bonzini
It's common for multiple narrow flash chips to be hooked up in parallel
to support wider buses. For example, four 8-bit wide flash chips (x8)
may be combined in parallel to produce a 32-bit wide device. Similarly,
two 16-bit wide chips (x16) may be combined.
This commit introduces `device-width` and `max-device-width` properties,
similar to pflash_cfi01, with the following meanings:
- `width`: The width of the logical, qemu device (same as before);
- `device-width`: The width of an individual flash chip, defaulting to
`width`; and
- `max-device-width`: The maximum width of an individual flash chip,
defaulting to `device-width`.
Nothing needs to change to support reading such interleaved devices but
commands (e.g., erase and programming) must be sent to all devices at
the same time or else the various chips will be in different states.
For example, a 4-byte wide logical device can be composed of four x8/x16
devices in x8 mode. That is, each device supports both x8 or x16 and
they're being used in the byte, rather than word, mode. This
configuration would have `width=4`, `device-width=1`, and
`max-device-width=2`.
In addition to commands being sent to all devices, guest firmware
expects the status and CFI queries to be replicated for each device.
(The one exception to the response replication is that each device gets
to report its own status bit DQ7 while programming because its value
depends on the value being programmed which will usually differ for each
device.)
Testing is limited to 16-bit wide devices due to the current inability
to override the properties set by `pflash_cfi02_register`, but multiple
configurations are tested.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 270 +++++++++++++++++-------
tests/pflash-cfi02-test.c | 418 +++++++++++++++++++++++++++++---------
2 files changed, 523 insertions(+), 165 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index e4bff0c8f8..101628b4ec 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -28,7 +28,6 @@
* - unlock bypass command
* - CFI queries
*
- * It does not support flash interleaving.
* It does not implement boot blocs with reduced size
* It does not implement software data protection as found in many real chips
* It does not implement erase suspend/resume commands
@@ -67,15 +66,19 @@ struct PFlashCFI02 {
BlockBackend *blk;
uint32_t sector_len;
uint32_t nb_blocs;
- uint32_t chip_len;
+ uint64_t total_len;
+ uint64_t interleave_multiplier;
uint8_t mappings;
- uint8_t width;
+ uint8_t bank_width; /* Width of the QEMU device in bytes. */
+ uint8_t device_width; /* Width of individual pflash chip. */
+ uint8_t max_device_width; /* Maximum width of individual pflash chip. */
uint8_t be;
+ int device_shift; /* Amount to shift an offset to get a device address. */
int wcycle; /* if 0, the flash is read normally */
int bypass;
int ro;
uint8_t cmd;
- uint8_t status;
+ uint64_t status;
/* FIXME: implement array device properties */
uint16_t ident0;
uint16_t ident1;
@@ -103,16 +106,17 @@ struct PFlashCFI02 {
*/
static inline void toggle_dq7(PFlashCFI02 *pfl)
{
- pfl->status ^= 0x80;
+ pfl->status ^= pfl->interleave_multiplier * 0x80;
}
/*
* Set status bit DQ7 to bit 7 of value.
*/
-static inline void set_dq7(PFlashCFI02 *pfl, uint8_t value)
+static inline void set_dq7(PFlashCFI02 *pfl, uint64_t value)
{
- pfl->status &= 0x7F;
- pfl->status |= value & 0x80;
+ uint64_t mask = pfl->interleave_multiplier * 0x80;
+ pfl->status &= ~mask;
+ pfl->status |= value & mask;
}
/*
@@ -120,7 +124,7 @@ static inline void set_dq7(PFlashCFI02 *pfl, uint8_t value)
*/
static inline void toggle_dq6(PFlashCFI02 *pfl)
{
- pfl->status ^= 0x40;
+ pfl->status ^= pfl->interleave_multiplier * 0x40;
}
/*
@@ -188,7 +192,6 @@ static uint64_t pflash_data_read(PFlashCFI02 *pfl, hwaddr offset,
static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
{
PFlashCFI02 *pfl = opaque;
- hwaddr boff;
uint64_t ret;
ret = -1;
@@ -198,12 +201,10 @@ static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
++pfl->read_counter > PFLASH_LAZY_ROMD_THRESHOLD) {
pflash_register_memory(pfl, 1);
}
- offset &= pfl->chip_len - 1;
- boff = offset & 0xFF;
- if (pfl->width == 2)
- boff = boff >> 1;
- else if (pfl->width == 4)
- boff = boff >> 2;
+ /* Mask by the total length of the chip to account for alias mappings. */
+ offset &= pfl->total_len - 1;
+ hwaddr device_addr = offset >> pfl->device_shift;
+
switch (pfl->cmd) {
default:
/* This should never happen : reset state & treat it as a read*/
@@ -215,29 +216,32 @@ static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
/* We accept reads during second unlock sequence... */
case 0x00:
/* Flash area read */
- ret = pflash_data_read(pfl, offset, width);
- break;
+ return pflash_data_read(pfl, offset, width);
case 0x90:
/* flash ID read */
- switch (boff) {
+ switch (device_addr & 0xFF) {
case 0x00:
+ ret = pfl->ident0;
+ break;
case 0x01:
- ret = boff & 0x01 ? pfl->ident1 : pfl->ident0;
+ ret = pfl->ident1;
break;
case 0x02:
ret = 0x00; /* Pretend all sectors are unprotected */
break;
case 0x0E:
case 0x0F:
- ret = boff & 0x01 ? pfl->ident3 : pfl->ident2;
+ ret = device_addr & 0x01 ? pfl->ident3 : pfl->ident2;
if (ret != (uint8_t)-1) {
break;
}
/* Fall through to data read. */
default:
- ret = pflash_data_read(pfl, offset, width);
+ return pflash_data_read(pfl, offset, width);
}
- DPRINTF("%s: ID " TARGET_FMT_plx " %" PRIx64 "\n", __func__, boff, ret);
+ ret *= pfl->interleave_multiplier;
+ DPRINTF("%s: ID " TARGET_FMT_plx " %" PRIx64 "\n",
+ __func__, device_addr & 0xFF, ret);
break;
case 0xA0:
case 0x10:
@@ -250,8 +254,8 @@ static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
break;
case 0x98:
/* CFI query mode */
- if (boff < sizeof(pfl->cfi_table)) {
- ret = pfl->cfi_table[boff];
+ if (device_addr < sizeof(pfl->cfi_table)) {
+ ret = pfl->interleave_multiplier * pfl->cfi_table[device_addr];
} else {
ret = 0;
}
@@ -279,30 +283,36 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
unsigned int width)
{
PFlashCFI02 *pfl = opaque;
- hwaddr boff;
uint8_t *p;
uint8_t cmd;
cmd = value;
- if (pfl->cmd != 0xA0 && cmd == 0xF0) {
-#if 0
- DPRINTF("%s: flash reset asked (%02x %02x)\n",
- __func__, pfl->cmd, cmd);
-#endif
- goto reset_flash;
+ if (pfl->cmd != 0xA0) {
+ if (value != pfl->interleave_multiplier * cmd) {
+ DPRINTF("%s: cmd 0x%02x not sent to all devices: expected="
+ "0x%0*" PRIx64 " actual=0x%0*" PRIx64 "\n",
+ __func__, cmd,
+ pfl->bank_width * 2, pfl->interleave_multiplier * cmd,
+ pfl->bank_width * 2, value);
+ }
+
+ if (cmd == 0xF0) {
+ goto reset_flash;
+ }
}
+
trace_pflash_write(offset, value, width, pfl->wcycle);
- offset &= pfl->chip_len - 1;
-
- DPRINTF("%s: offset " TARGET_FMT_plx " %08" PRIx64 " %d\n", __func__,
- offset, value, width);
- boff = offset;
- if (pfl->width == 2)
- boff = boff >> 1;
- else if (pfl->width == 4)
- boff = boff >> 2;
- /* Only the least-significant 11 bits are used in most cases. */
- boff &= 0x7FF;
+
+ /* Mask by the total length of the chip to account for alias mappings. */
+ offset &= pfl->total_len - 1;
+
+ DPRINTF("%s: offset " TARGET_FMT_plx " 0x%0*" PRIx64 "\n",
+ __func__, offset, width * 2, value);
+
+ hwaddr device_addr = (offset >> pfl->device_shift);
+ /* Address bits A11 and greater are don't cares for most commands. */
+ unsigned int masked_addr = device_addr & 0x7FF;
+
switch (pfl->wcycle) {
case 0:
/* Set the device in I/O access mode if required */
@@ -311,16 +321,16 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
pfl->read_counter = 0;
/* We're in read mode */
check_unlock0:
- if (boff == 0x55 && cmd == 0x98) {
+ if (masked_addr == 0x55 && cmd == 0x98) {
enter_CFI_mode:
/* Enter CFI query mode */
pfl->wcycle = WCYCLE_CFI;
pfl->cmd = 0x98;
return;
}
- if (boff != pfl->unlock_addr0 || cmd != 0xAA) {
- DPRINTF("%s: unlock0 failed " TARGET_FMT_plx " %02x %04x\n",
- __func__, boff, cmd, pfl->unlock_addr0);
+ if (masked_addr != pfl->unlock_addr0 || cmd != 0xAA) {
+ DPRINTF("%s: unlock0 failed %04x %02x %04x\n",
+ __func__, masked_addr, cmd, pfl->unlock_addr0);
goto reset_flash;
}
DPRINTF("%s: unlock sequence started\n", __func__);
@@ -328,18 +338,18 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
case 1:
/* We started an unlock sequence */
check_unlock1:
- if (boff != pfl->unlock_addr1 || cmd != 0x55) {
- DPRINTF("%s: unlock1 failed " TARGET_FMT_plx " %02x\n", __func__,
- boff, cmd);
+ if (masked_addr != pfl->unlock_addr1 || cmd != 0x55) {
+ DPRINTF("%s: unlock1 failed %03x %02x\n", __func__,
+ masked_addr, cmd);
goto reset_flash;
}
DPRINTF("%s: unlock sequence done\n", __func__);
break;
case 2:
/* We finished an unlock sequence */
- if (!pfl->bypass && boff != pfl->unlock_addr0) {
- DPRINTF("%s: command failed " TARGET_FMT_plx " %02x\n", __func__,
- boff, cmd);
+ if (!pfl->bypass && masked_addr != pfl->unlock_addr0) {
+ DPRINTF("%s: command failed %03x %02x\n", __func__,
+ masked_addr, cmd);
goto reset_flash;
}
switch (cmd) {
@@ -390,8 +400,9 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
goto reset_flash;
}
/* We can enter CFI query mode from autoselect mode */
- if (boff == 0x55 && cmd == 0x98)
+ if (masked_addr == 0x55 && cmd == 0x98) {
goto enter_CFI_mode;
+ }
/* No break here */
default:
DPRINTF("%s: invalid write for command %02x\n",
@@ -416,7 +427,7 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
case 5:
switch (cmd) {
case 0x10:
- if (boff != pfl->unlock_addr0) {
+ if (masked_addr != pfl->unlock_addr0) {
DPRINTF("%s: chip erase: invalid address " TARGET_FMT_plx "\n",
__func__, offset);
goto reset_flash;
@@ -424,8 +435,8 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* Chip erase */
DPRINTF("%s: start chip erase\n", __func__);
if (!pfl->ro) {
- memset(pfl->storage, 0xFF, pfl->chip_len);
- pflash_update(pfl, 0, pfl->chip_len);
+ memset(pfl->storage, 0xFF, pfl->total_len);
+ pflash_update(pfl, 0, pfl->total_len);
}
set_dq7(pfl, 0x00);
/* Let's wait 5 seconds before chip erase is done */
@@ -521,22 +532,132 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
return;
}
+ if (pfl->bank_width == 0) {
+ error_setg(errp, "attribute \"width\" not specified or zero.");
+ return;
+ }
+
+ /*
+ * device-width defaults to width and max-device-width defaults to
+ * device-width. Check that the device-width and max-device-width
+ * configurations are supported.
+ */
+ if (pfl->device_width == 0) {
+ pfl->device_width = pfl->bank_width;
+ }
+ if (pfl->max_device_width == 0) {
+ pfl->max_device_width = pfl->device_width;
+ }
+ if (pfl->bank_width % pfl->device_width != 0) {
+ error_setg(errp,
+ "attribute \"width\" (%u) not a multiple of attribute "
+ "\"device-width\" (%u).",
+ pfl->bank_width, pfl->device_width);
+ return;
+ }
+
+ /*
+ * Writing commands to the flash device and reading CFI responses or
+ * status values requires transforming a QEMU device offset into a
+ * flash device address given in terms of the device's maximum width. We
+ * can do this by shifting a QEMU device offset right a constant number of
+ * bits depending on the bank_width, device_width, and max_device_width.
+ *
+ * num_devices = bank_width / device_width is the number of interleaved
+ * flash devices. To compute a device byte address, we need to divide
+ * offset by num_devices (equivalently shift right by log2(num_devices)).
+ * To turn a device byte address into a device word address, we need to
+ * divide by max_device_width (equivalently shift right by
+ * log2(max_device_width)).
+ *
+ * In tabular form.
+ * ==================================================================
+ * bank_width device_width max_device_width num_devices shift
+ * ------------------------------------------------------------------
+ * 1 1 1 1 0
+ * 1 1 2 1 1
+ * 2 1 1 2 1
+ * 2 1 2 2 2
+ * 2 2 2 1 1
+ * 4 1 1 4 2
+ * 4 1 2 4 3
+ * 4 1 4 4 4
+ * 4 2 2 2 2
+ * 4 2 4 2 3
+ * 4 4 4 1 2
+ * ==================================================================
+ */
+ pfl->device_shift = ctz32(pfl->bank_width) - ctz32(pfl->device_width) +
+ ctz32(pfl->max_device_width);
+ pfl->interleave_multiplier = 0;
+ for (unsigned int shift = 0; shift < pfl->bank_width;
+ shift += pfl->device_width) {
+ pfl->interleave_multiplier |= 1 << (shift * 8);
+ }
+
+ uint16_t device_interface_code;
+ if (pfl->max_device_width == 1 && pfl->device_width == 1) {
+ device_interface_code = 0; /* x8 only. */
+ } else if (pfl->max_device_width == 2 &&
+ (pfl->device_width == 1 || pfl->device_width == 2)) {
+ /* XXX: Some devices only support x16, this code doesn't model them. */
+ device_interface_code = 2; /* Supports x8 or x16. */
+ } else if (pfl->max_device_width == 4 && pfl->device_width == 1) {
+ /*
+ * XXX: this is x32-only. The standards I've seen don't specify a value
+ * for x8/x32 but do mention them.
+ */
+ device_interface_code = 3; /* x32 only. */
+ } else if (pfl->max_device_width == 4 &&
+ (pfl->device_width == 2 || pfl->device_width == 4)) {
+ device_interface_code = 4; /* Supports x16 or x32. */
+ } else {
+ error_setg(errp,
+ "unsupported configuration: \"device-width\"=%u "
+ "\"max-device-width\"=%u.",
+ pfl->device_width, pfl->max_device_width);
+ return;
+ }
+
+ pfl->total_len = pfl->sector_len * pfl->nb_blocs;
+
+ /*
+ * If the flash is not a power of 2, then the code for handling multiple
+ * mappings will not work correctly.
+ */
+ if (!is_power_of_2(pfl->total_len)) {
+ error_setg(errp, "total pflash length (%" PRIx64 ") not a power of 2.",
+ pfl->total_len);
+ return;
+ }
+
+ int num_devices = pfl->bank_width / pfl->device_width;
+ uint64_t sector_len_per_device = pfl->sector_len / num_devices;
+ uint64_t device_len = sector_len_per_device * pfl->nb_blocs;
+
+ if (sector_len_per_device & 0xff || sector_len_per_device >= (1 << 24)) {
+ error_setg(errp,
+ "unsupported configuration: sector length per device = "
+ "%" PRIx64 ".",
+ sector_len_per_device);
+ return;
+ }
+
+ memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl),
+ &pflash_cfi02_ops, pfl, pfl->name,
+ pfl->total_len, &local_err);
/* Only 11 bits are used in the comparison. */
pfl->unlock_addr0 &= 0x7FF;
pfl->unlock_addr1 &= 0x7FF;
chip_len = pfl->sector_len * pfl->nb_blocs;
- memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl),
- &pflash_cfi02_ops, pfl, pfl->name,
- chip_len, &local_err);
if (local_err) {
error_propagate(errp, local_err);
return;
}
pfl->storage = memory_region_get_ram_ptr(&pfl->orig_mem);
- pfl->chip_len = chip_len;
if (pfl->blk) {
uint64_t perm;
@@ -566,6 +687,7 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->wcycle = 0;
pfl->cmd = 0;
pfl->status = 0;
+
/* Hardcoded CFI table (mostly from SG29 Spansion flash) */
/* Standard "QRY" string */
pfl->cfi_table[0x10] = 'Q';
@@ -591,8 +713,8 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->cfi_table[0x1D] = 0x00;
/* Vpp max (no Vpp pin) */
pfl->cfi_table[0x1E] = 0x00;
- /* Reserved */
- pfl->cfi_table[0x1F] = 0x07;
+ /* Timeout per single byte/word write (16 us) */
+ pfl->cfi_table[0x1F] = 0x04;
/* Timeout for min size buffer write (NA) */
pfl->cfi_table[0x20] = 0x00;
/* Typical timeout for block erase (512 ms) */
@@ -608,13 +730,13 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
/* Max timeout for chip erase */
pfl->cfi_table[0x26] = 0x0D;
/* Device size */
- pfl->cfi_table[0x27] = ctz32(chip_len);
- /* Flash device interface (8 & 16 bits) */
- pfl->cfi_table[0x28] = 0x02;
- pfl->cfi_table[0x29] = 0x00;
+ pfl->cfi_table[0x27] = ctz32(device_len);
+ /* Flash device interface */
+ pfl->cfi_table[0x28] = device_interface_code;
+ pfl->cfi_table[0x29] = device_interface_code >> 8;
/* Max number of bytes in multi-bytes write */
/* XXX: disable buffered write as it's not supported */
- // pfl->cfi_table[0x2A] = 0x05;
+ /* pfl->cfi_table[0x2A] = 0x05; */
pfl->cfi_table[0x2A] = 0x00;
pfl->cfi_table[0x2B] = 0x00;
/* Number of erase block regions (uniform) */
@@ -622,8 +744,8 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
/* Erase block region 1 */
pfl->cfi_table[0x2D] = pfl->nb_blocs - 1;
pfl->cfi_table[0x2E] = (pfl->nb_blocs - 1) >> 8;
- pfl->cfi_table[0x2F] = pfl->sector_len >> 8;
- pfl->cfi_table[0x30] = pfl->sector_len >> 16;
+ pfl->cfi_table[0x2F] = sector_len_per_device >> 8;
+ pfl->cfi_table[0x30] = sector_len_per_device >> 16;
/* Extended */
pfl->cfi_table[0x31] = 'P';
@@ -648,7 +770,9 @@ static Property pflash_cfi02_properties[] = {
DEFINE_PROP_DRIVE("drive", PFlashCFI02, blk),
DEFINE_PROP_UINT32("num-blocks", PFlashCFI02, nb_blocs, 0),
DEFINE_PROP_UINT32("sector-length", PFlashCFI02, sector_len, 0),
- DEFINE_PROP_UINT8("width", PFlashCFI02, width, 0),
+ DEFINE_PROP_UINT8("width", PFlashCFI02, bank_width, 0),
+ DEFINE_PROP_UINT8("device-width", PFlashCFI02, device_width, 0),
+ DEFINE_PROP_UINT8("max-device-width", PFlashCFI02, max_device_width, 0),
DEFINE_PROP_UINT8("mappings", PFlashCFI02, mappings, 0),
DEFINE_PROP_UINT8("big-endian", PFlashCFI02, be, 0),
DEFINE_PROP_UINT16("id0", PFlashCFI02, ident0, 0),
@@ -696,7 +820,7 @@ PFlashCFI02 *pflash_cfi02_register(hwaddr base,
hwaddr size,
BlockBackend *blk,
uint32_t sector_len,
- int nb_mappings, int width,
+ int nb_mappings, int bank_width,
uint16_t id0, uint16_t id1,
uint16_t id2, uint16_t id3,
uint16_t unlock_addr0,
@@ -711,7 +835,7 @@ PFlashCFI02 *pflash_cfi02_register(hwaddr base,
assert(size % sector_len == 0);
qdev_prop_set_uint32(dev, "num-blocks", size / sector_len);
qdev_prop_set_uint32(dev, "sector-length", sector_len);
- qdev_prop_set_uint8(dev, "width", width);
+ qdev_prop_set_uint8(dev, "width", bank_width);
qdev_prop_set_uint8(dev, "mappings", nb_mappings);
qdev_prop_set_uint8(dev, "big-endian", !!be);
qdev_prop_set_uint16(dev, "id0", id0);
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index b91bb66a79..4d621e584d 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -21,10 +21,15 @@
#define MP_FLASH_SIZE_MAX (32 * 1024 * 1024)
#define BASE_ADDR (0x100000000ULL - MP_FLASH_SIZE_MAX)
-#define FLASH_WIDTH 2
-#define CFI_ADDR (FLASH_WIDTH * 0x55)
-#define UNLOCK0_ADDR (FLASH_WIDTH * 0x555)
-#define UNLOCK1_ADDR (FLASH_WIDTH * 0x2AA)
+/* Use a newtype to keep flash addresses separate from byte addresses. */
+typedef struct {
+ uint64_t addr;
+} faddr;
+#define FLASH_ADDR(x) ((faddr) { .addr = (x) })
+
+#define CFI_ADDR FLASH_ADDR(0x55)
+#define UNLOCK0_ADDR FLASH_ADDR(0x555)
+#define UNLOCK1_ADDR FLASH_ADDR(0x2AA)
#define CFI_CMD 0x98
#define UNLOCK0_CMD 0xAA
@@ -37,168 +42,332 @@
#define UNLOCK_BYPASS_CMD 0x20
#define UNLOCK_BYPASS_RESET_CMD 0x00
+typedef struct {
+ int bank_width;
+ int device_width;
+ int max_device_width;
+} FlashConfig;
+
static char image_path[] = "/tmp/qtest.XXXXXX";
-static inline void flash_write(uint64_t byte_addr, uint16_t data)
+/*
+ * The pflash implementation allows some parameters to be unspecified. We want
+ * to test those configurations but we also need to know the real values in
+ * our testing code. So after we launch qemu, we'll need a new FlashConfig
+ * with the correct values filled in.
+ */
+static FlashConfig expand_config_defaults(const FlashConfig *c)
{
- qtest_writew(global_qtest, BASE_ADDR + byte_addr, data);
+ FlashConfig ret = *c;
+
+ if (ret.device_width == 0) {
+ ret.device_width = ret.bank_width;
+ }
+ if (ret.max_device_width == 0) {
+ ret.max_device_width = ret.device_width;
+ }
+ return ret;
+}
+
+/*
+ * Return a bit mask suitable for extracting the least significant
+ * status/query response from an interleaved response.
+ */
+static inline uint64_t device_mask(const FlashConfig *c)
+{
+ if (c->device_width == 8) {
+ return (uint64_t)-1;
+ }
+ return (1ULL << (c->device_width * 8)) - 1ULL;
+}
+
+/*
+ * Return a bit mask exactly as long as the bank_width.
+ */
+static inline uint64_t bank_mask(const FlashConfig *c)
+{
+ if (c->bank_width == 8) {
+ return (uint64_t)-1;
+ }
+ return (1ULL << (c->bank_width * 8)) - 1ULL;
+}
+
+static inline void flash_write(const FlashConfig *c, uint64_t byte_addr,
+ uint64_t data)
+{
+ /* Sanity check our tests. */
+ assert((data & ~bank_mask(c)) == 0);
+ uint64_t addr = BASE_ADDR + byte_addr;
+ switch (c->bank_width) {
+ case 1:
+ qtest_writeb(global_qtest, addr, data);
+ break;
+ case 2:
+ qtest_writew(global_qtest, addr, data);
+ break;
+ case 4:
+ qtest_writel(global_qtest, addr, data);
+ break;
+ case 8:
+ qtest_writeq(global_qtest, addr, data);
+ break;
+ default:
+ abort();
+ }
+}
+
+static inline uint64_t flash_read(const FlashConfig *c, uint64_t byte_addr)
+{
+ uint64_t addr = BASE_ADDR + byte_addr;
+ switch (c->bank_width) {
+ case 1:
+ return qtest_readb(global_qtest, addr);
+ case 2:
+ return qtest_readw(global_qtest, addr);
+ case 4:
+ return qtest_readl(global_qtest, addr);
+ case 8:
+ return qtest_readq(global_qtest, addr);
+ default:
+ abort();
+ }
+}
+
+/*
+ * Convert a flash address expressed in the maximum width of the device as a
+ * byte address.
+ */
+static inline uint64_t as_byte_addr(const FlashConfig *c, faddr flash_addr)
+{
+ /*
+ * Command addresses are always given as addresses in the maximum
+ * supported bus size for the flash chip. So an x8/x16 chip in x8 mode
+ * uses addresses 0xAAA and 0x555 to unlock because the least significant
+ * bit is ignored. (0x555 rather than 0x554 is traditional.)
+ *
+ * Interleaving flash chips use the least significant bits of a byte
+ * address to refer to data from the individual chips. Two interleaved x8
+ * devices would use command addresses 0xAAA and 0x554. Two interleaved
+ * x16 devices would use 0x1554 and 0xAA8.
+ *
+ * More exotic configurations are possible. Two interleaved x8/x16 devices
+ * in x8 mode would also use 0x1554 and 0xAA8.
+ *
+ * In general we need to multiply an address by the number of devices,
+ * which is bank_width / device_width, and multiply that by the maximum
+ * device width.
+ */
+ int num_devices = c->bank_width / c->device_width;
+ return flash_addr.addr * (num_devices * c->max_device_width);
+}
+
+/*
+ * Return the command value or expected status replicated across all devices.
+ */
+static inline uint64_t replicate(const FlashConfig *c, uint64_t data)
+{
+ /* Sanity check our tests. */
+ assert((data & ~device_mask(c)) == 0);
+ for (int i = c->device_width; i < c->bank_width; i += c->device_width) {
+ data |= data << (c->device_width * 8);
+ }
+ return data;
+}
+
+static inline void flash_cmd(const FlashConfig *c, faddr cmd_addr,
+ uint8_t cmd)
+{
+ flash_write(c, as_byte_addr(c, cmd_addr), replicate(c, cmd));
+}
+
+static inline uint64_t flash_query(const FlashConfig *c, faddr query_addr)
+{
+ return flash_read(c, as_byte_addr(c, query_addr));
}
-static inline uint16_t flash_read(uint64_t byte_addr)
+static inline uint64_t flash_query_1(const FlashConfig *c, faddr query_addr)
{
- return qtest_readw(global_qtest, BASE_ADDR + byte_addr);
+ return flash_query(c, query_addr) & device_mask(c);
}
-static void unlock(void)
+static void unlock(const FlashConfig *c)
{
- flash_write(UNLOCK0_ADDR, UNLOCK0_CMD);
- flash_write(UNLOCK1_ADDR, UNLOCK1_CMD);
+ flash_cmd(c, UNLOCK0_ADDR, UNLOCK0_CMD);
+ flash_cmd(c, UNLOCK1_ADDR, UNLOCK1_CMD);
}
-static void reset(void)
+static void reset(const FlashConfig *c)
{
- flash_write(0, RESET_CMD);
+ flash_cmd(c, FLASH_ADDR(0), RESET_CMD);
}
-static void sector_erase(uint64_t byte_addr)
+static void sector_erase(const FlashConfig *c, uint64_t byte_addr)
{
- unlock();
- flash_write(UNLOCK0_ADDR, 0x80);
- unlock();
- flash_write(byte_addr, SECTOR_ERASE_CMD);
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, 0x80);
+ unlock(c);
+ flash_write(c, byte_addr, replicate(c, SECTOR_ERASE_CMD));
}
-static void wait_for_completion(uint64_t byte_addr)
+static void wait_for_completion(const FlashConfig *c, uint64_t byte_addr)
{
/* If DQ6 is toggling, step the clock and ensure the toggle stops. */
- if ((flash_read(byte_addr) & 0x40) ^ (flash_read(byte_addr) & 0x40)) {
+ const uint64_t dq6 = replicate(c, 0x40);
+ if ((flash_read(c, byte_addr) & dq6) ^ (flash_read(c, byte_addr) & dq6)) {
/* Wait for erase or program to finish. */
clock_step_next();
/* Ensure that DQ6 has stopped toggling. */
- g_assert_cmpint(flash_read(byte_addr), ==, flash_read(byte_addr));
+ g_assert_cmpint(flash_read(c, byte_addr), ==, flash_read(c, byte_addr));
}
}
-static void bypass_program(uint64_t byte_addr, uint16_t data)
+static void bypass_program(const FlashConfig *c, uint64_t byte_addr,
+ uint16_t data)
{
- flash_write(UNLOCK0_ADDR, PROGRAM_CMD);
- flash_write(byte_addr, data);
+ flash_cmd(c, UNLOCK0_ADDR, PROGRAM_CMD);
+ flash_write(c, byte_addr, data);
/*
* Data isn't valid until DQ6 stops toggling. We don't model this as
* writes are immediate, but if this changes in the future, we can wait
* until the program is complete.
*/
- wait_for_completion(byte_addr);
+ wait_for_completion(c, byte_addr);
}
-static void program(uint64_t byte_addr, uint16_t data)
+static void program(const FlashConfig *c, uint64_t byte_addr, uint16_t data)
{
- unlock();
- bypass_program(byte_addr, data);
+ unlock(c);
+ bypass_program(c, byte_addr, data);
}
-static void chip_erase(void)
+static void chip_erase(const FlashConfig *c)
{
- unlock();
- flash_write(UNLOCK0_ADDR, 0x80);
- unlock();
- flash_write(UNLOCK0_ADDR, SECTOR_ERASE_CMD);
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, 0x80);
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, CHIP_ERASE_CMD);
}
-static void test_flash(void)
+static void test_flash(const void *opaque)
{
- global_qtest = qtest_initf("-M musicpal,accel=qtest "
- "-drive if=pflash,file=%s,format=raw,copy-on-read",
- image_path);
+ const FlashConfig *config = opaque;
+ global_qtest = qtest_initf("-M musicpal,accel=qtest"
+ " -drive if=pflash,file=%s,format=raw,"
+ "copy-on-read"
+ " -global driver=cfi.pflash02,"
+ "property=device-width,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=max-device-width,value=%d",
+ image_path,
+ config->device_width,
+ config->max_device_width);
+
+ const FlashConfig explicit_config = expand_config_defaults(config);
+ const FlashConfig *c = &explicit_config;
+
/* Check the IDs. */
- unlock();
- flash_write(UNLOCK0_ADDR, AUTOSELECT_CMD);
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0000), ==, 0x00BF);
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0001), ==, 0x236D);
- reset();
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, AUTOSELECT_CMD);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
+ if (c->device_width >= 2) {
+ /*
+ * XXX: The ID returned by the musicpal flash chip is 16 bits which
+ * wouldn't happen with an 8-bit device. It would probably be best to
+ * prohibit addresses larger than the device width in pflash_cfi02.c,
+ * but then we couldn't test smaller device widths at all.
+ */
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(1)), ==,
+ replicate(c, 0x236D));
+ }
+ reset(c);
/* Check the erase blocks. */
- flash_write(CFI_ADDR, CFI_CMD);
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x10), ==, 'Q');
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x11), ==, 'R');
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x12), ==, 'Y');
+ flash_cmd(c, CFI_ADDR, CFI_CMD);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x10)), ==, replicate(c, 'Q'));
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x11)), ==, replicate(c, 'R'));
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x12)), ==, replicate(c, 'Y'));
/* Num erase regions. */
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x2C), >=, 1);
- uint32_t nb_sectors = flash_read(FLASH_WIDTH * 0x2D) +
- (flash_read(FLASH_WIDTH * 0x2E) << 8) + 1;
- uint32_t sector_len = (flash_read(FLASH_WIDTH * 0x2F) << 8) +
- (flash_read(FLASH_WIDTH * 0x30) << 16);
- reset();
+ g_assert_cmpint(flash_query_1(c, FLASH_ADDR(0x2C)), >=, 1);
+ uint32_t nb_sectors = flash_query_1(c, FLASH_ADDR(0x2D)) +
+ (flash_query_1(c, FLASH_ADDR(0x2E)) << 8) + 1;
+ uint32_t sector_len = (flash_query_1(c, FLASH_ADDR(0x2F)) << 8) +
+ (flash_query_1(c, FLASH_ADDR(0x30)) << 16);
+ reset(c);
+ const uint64_t dq7 = replicate(c, 0x80);
+ const uint64_t dq6 = replicate(c, 0x40);
/* Erase and program sector. */
for (uint32_t i = 0; i < nb_sectors; ++i) {
uint64_t byte_addr = i * sector_len;
- sector_erase(byte_addr);
+ sector_erase(c, byte_addr);
/* Read toggle. */
- uint16_t status0 = flash_read(byte_addr);
+ uint64_t status0 = flash_read(c, byte_addr);
/* DQ7 is 0 during an erase. */
- g_assert_cmpint(status0 & 0x80, ==, 0);
- uint16_t status1 = flash_read(byte_addr);
+ g_assert_cmpint(status0 & dq7, ==, 0);
+ uint64_t status1 = flash_read(c, byte_addr);
/* DQ6 toggles during an erase. */
- g_assert_cmpint(status0 & 0x40, !=, status1 & 0x40);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
/* Wait for erase to complete. */
clock_step_next();
/* Ensure DQ6 has stopped toggling. */
- g_assert_cmpint(flash_read(byte_addr), ==, flash_read(byte_addr));
+ g_assert_cmpint(flash_read(c, byte_addr), ==, flash_read(c, byte_addr));
/* Now the data should be valid. */
- g_assert_cmpint(flash_read(byte_addr), ==, 0xFFFF);
+ g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
/* Program a bit pattern. */
- program(byte_addr, 0x5555);
- g_assert_cmpint(flash_read(byte_addr), ==, 0x5555);
- program(byte_addr, 0xAA55);
- g_assert_cmpint(flash_read(byte_addr), ==, 0x0055);
+ program(c, byte_addr, 0x55);
+ g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x55);
+ program(c, byte_addr, 0xA5);
+ g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x05);
}
/* Erase the chip. */
- chip_erase();
+ chip_erase(c);
/* Read toggle. */
- uint16_t status0 = flash_read(0);
+ uint64_t status0 = flash_read(c, 0);
/* DQ7 is 0 during an erase. */
- g_assert_cmpint(status0 & 0x80, ==, 0);
- uint16_t status1 = flash_read(0);
+ g_assert_cmpint(status0 & dq7, ==, 0);
+ uint64_t status1 = flash_read(c, 0);
/* DQ6 toggles during an erase. */
- g_assert_cmpint(status0 & 0x40, !=, status1 & 0x40);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
/* Wait for erase to complete. */
clock_step_next();
/* Ensure DQ6 has stopped toggling. */
- g_assert_cmpint(flash_read(0), ==, flash_read(0));
+ g_assert_cmpint(flash_read(c, 0), ==, flash_read(c, 0));
/* Now the data should be valid. */
- g_assert_cmpint(flash_read(0), ==, 0xFFFF);
+
+ for (uint32_t i = 0; i < nb_sectors; ++i) {
+ uint64_t byte_addr = i * sector_len;
+ g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
+ }
/* Unlock bypass */
- unlock();
- flash_write(UNLOCK0_ADDR, UNLOCK_BYPASS_CMD);
- bypass_program(0, 0x0123);
- bypass_program(2, 0x4567);
- bypass_program(4, 0x89AB);
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, UNLOCK_BYPASS_CMD);
+ bypass_program(c, 0 * c->bank_width, 0x01);
+ bypass_program(c, 1 * c->bank_width, 0x23);
+ bypass_program(c, 2 * c->bank_width, 0x45);
/*
* Test that bypass programming, unlike normal programming can use any
* address for the PROGRAM_CMD.
*/
- flash_write(6, PROGRAM_CMD);
- flash_write(6, 0xCDEF);
- wait_for_completion(6);
- flash_write(0, UNLOCK_BYPASS_RESET_CMD);
- bypass_program(8, 0x55AA); /* Should fail. */
- g_assert_cmpint(flash_read(0), ==, 0x0123);
- g_assert_cmpint(flash_read(2), ==, 0x4567);
- g_assert_cmpint(flash_read(4), ==, 0x89AB);
- g_assert_cmpint(flash_read(6), ==, 0xCDEF);
- g_assert_cmpint(flash_read(8), ==, 0xFFFF);
+ flash_cmd(c, FLASH_ADDR(3 * c->bank_width), PROGRAM_CMD);
+ flash_write(c, 3 * c->bank_width, 0x67);
+ wait_for_completion(c, 3 * c->bank_width);
+ flash_cmd(c, FLASH_ADDR(0), UNLOCK_BYPASS_RESET_CMD);
+ bypass_program(c, 4 * c->bank_width, 0x89); /* Should fail. */
+ g_assert_cmpint(flash_read(c, 0 * c->bank_width), ==, 0x01);
+ g_assert_cmpint(flash_read(c, 1 * c->bank_width), ==, 0x23);
+ g_assert_cmpint(flash_read(c, 2 * c->bank_width), ==, 0x45);
+ g_assert_cmpint(flash_read(c, 3 * c->bank_width), ==, 0x67);
+ g_assert_cmpint(flash_read(c, 4 * c->bank_width), ==, bank_mask(c));
/* Test ignored high order bits of address. */
- flash_write(FLASH_WIDTH * 0x5555, UNLOCK0_CMD);
- flash_write(FLASH_WIDTH * 0x2AAA, UNLOCK1_CMD);
- flash_write(FLASH_WIDTH * 0x5555, AUTOSELECT_CMD);
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0000), ==, 0x00BF);
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0001), ==, 0x236D);
- reset();
+ flash_cmd(c, FLASH_ADDR(0x5555), UNLOCK0_CMD);
+ flash_cmd(c, FLASH_ADDR(0x2AAA), UNLOCK1_CMD);
+ flash_cmd(c, FLASH_ADDR(0x5555), AUTOSELECT_CMD);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
+ reset(c);
qtest_quit(global_qtest);
}
@@ -208,6 +377,61 @@ static void cleanup(void *opaque)
unlink(image_path);
}
+/*
+ * XXX: Tests are limited to bank_width = 2 for now because that's what
+ * hw/arm/musicpal.c has.
+ */
+static const FlashConfig configuration[] = {
+ /* One x16 device. */
+ {
+ .bank_width = 2,
+ .device_width = 2,
+ .max_device_width = 2,
+ },
+ /* Implicitly one x16 device. */
+ {
+ .bank_width = 2,
+ .device_width = 0,
+ .max_device_width = 0,
+ },
+ /* Implicitly one x16 device. */
+ {
+ .bank_width = 2,
+ .device_width = 2,
+ .max_device_width = 0,
+ },
+ /* Interleave two x8 devices. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .max_device_width = 1,
+ },
+ /* Interleave two implicit x8 devices. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .max_device_width = 0,
+ },
+ /* Interleave two x8/x16 devices in x8 mode. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .max_device_width = 2,
+ },
+ /* One x16/x32 device in x16 mode. */
+ {
+ .bank_width = 2,
+ .device_width = 2,
+ .max_device_width = 4,
+ },
+ /* Two x8/x32 devices in x8 mode; I am not sure if such devices exist. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .max_device_width = 4,
+ },
+};
+
int main(int argc, char **argv)
{
int fd = mkstemp(image_path);
@@ -226,7 +450,17 @@ int main(int argc, char **argv)
qtest_add_abrt_handler(cleanup, NULL);
g_test_init(&argc, &argv, NULL);
- qtest_add_func("pflash-cfi02", test_flash);
+
+ size_t nb_configurations = sizeof configuration / sizeof configuration[0];
+ for (size_t i = 0; i < nb_configurations; ++i) {
+ const FlashConfig *config = &configuration[i];
+ char *path = g_strdup_printf("pflash-cfi02/%d-%d-%d",
+ config->bank_width,
+ config->device_width,
+ config->max_device_width);
+ qtest_add_data_func(path, config, test_flash);
+ g_free(path);
+ }
int result = g_test_run();
cleanup(NULL);
return result;
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 04/10] block/pflash_cfi02: Implement intereleaved flash devices
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 04/10] block/pflash_cfi02: Implement intereleaved flash devices Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
0 siblings, 0 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Laurent Vivier, Thomas Huth, Stephen Checkoway,
qemu-block, Max Reitz, Paolo Bonzini
It's common for multiple narrow flash chips to be hooked up in parallel
to support wider buses. For example, four 8-bit wide flash chips (x8)
may be combined in parallel to produce a 32-bit wide device. Similarly,
two 16-bit wide chips (x16) may be combined.
This commit introduces `device-width` and `max-device-width` properties,
similar to pflash_cfi01, with the following meanings:
- `width`: The width of the logical, qemu device (same as before);
- `device-width`: The width of an individual flash chip, defaulting to
`width`; and
- `max-device-width`: The maximum width of an individual flash chip,
defaulting to `device-width`.
Nothing needs to change to support reading such interleaved devices but
commands (e.g., erase and programming) must be sent to all devices at
the same time or else the various chips will be in different states.
For example, a 4-byte wide logical device can be composed of four x8/x16
devices in x8 mode. That is, each device supports both x8 or x16 and
they're being used in the byte, rather than word, mode. This
configuration would have `width=4`, `device-width=1`, and
`max-device-width=2`.
In addition to commands being sent to all devices, guest firmware
expects the status and CFI queries to be replicated for each device.
(The one exception to the response replication is that each device gets
to report its own status bit DQ7 while programming because its value
depends on the value being programmed which will usually differ for each
device.)
Testing is limited to 16-bit wide devices due to the current inability
to override the properties set by `pflash_cfi02_register`, but multiple
configurations are tested.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 270 +++++++++++++++++-------
tests/pflash-cfi02-test.c | 418 +++++++++++++++++++++++++++++---------
2 files changed, 523 insertions(+), 165 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index e4bff0c8f8..101628b4ec 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -28,7 +28,6 @@
* - unlock bypass command
* - CFI queries
*
- * It does not support flash interleaving.
* It does not implement boot blocs with reduced size
* It does not implement software data protection as found in many real chips
* It does not implement erase suspend/resume commands
@@ -67,15 +66,19 @@ struct PFlashCFI02 {
BlockBackend *blk;
uint32_t sector_len;
uint32_t nb_blocs;
- uint32_t chip_len;
+ uint64_t total_len;
+ uint64_t interleave_multiplier;
uint8_t mappings;
- uint8_t width;
+ uint8_t bank_width; /* Width of the QEMU device in bytes. */
+ uint8_t device_width; /* Width of individual pflash chip. */
+ uint8_t max_device_width; /* Maximum width of individual pflash chip. */
uint8_t be;
+ int device_shift; /* Amount to shift an offset to get a device address. */
int wcycle; /* if 0, the flash is read normally */
int bypass;
int ro;
uint8_t cmd;
- uint8_t status;
+ uint64_t status;
/* FIXME: implement array device properties */
uint16_t ident0;
uint16_t ident1;
@@ -103,16 +106,17 @@ struct PFlashCFI02 {
*/
static inline void toggle_dq7(PFlashCFI02 *pfl)
{
- pfl->status ^= 0x80;
+ pfl->status ^= pfl->interleave_multiplier * 0x80;
}
/*
* Set status bit DQ7 to bit 7 of value.
*/
-static inline void set_dq7(PFlashCFI02 *pfl, uint8_t value)
+static inline void set_dq7(PFlashCFI02 *pfl, uint64_t value)
{
- pfl->status &= 0x7F;
- pfl->status |= value & 0x80;
+ uint64_t mask = pfl->interleave_multiplier * 0x80;
+ pfl->status &= ~mask;
+ pfl->status |= value & mask;
}
/*
@@ -120,7 +124,7 @@ static inline void set_dq7(PFlashCFI02 *pfl, uint8_t value)
*/
static inline void toggle_dq6(PFlashCFI02 *pfl)
{
- pfl->status ^= 0x40;
+ pfl->status ^= pfl->interleave_multiplier * 0x40;
}
/*
@@ -188,7 +192,6 @@ static uint64_t pflash_data_read(PFlashCFI02 *pfl, hwaddr offset,
static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
{
PFlashCFI02 *pfl = opaque;
- hwaddr boff;
uint64_t ret;
ret = -1;
@@ -198,12 +201,10 @@ static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
++pfl->read_counter > PFLASH_LAZY_ROMD_THRESHOLD) {
pflash_register_memory(pfl, 1);
}
- offset &= pfl->chip_len - 1;
- boff = offset & 0xFF;
- if (pfl->width == 2)
- boff = boff >> 1;
- else if (pfl->width == 4)
- boff = boff >> 2;
+ /* Mask by the total length of the chip to account for alias mappings. */
+ offset &= pfl->total_len - 1;
+ hwaddr device_addr = offset >> pfl->device_shift;
+
switch (pfl->cmd) {
default:
/* This should never happen : reset state & treat it as a read*/
@@ -215,29 +216,32 @@ static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
/* We accept reads during second unlock sequence... */
case 0x00:
/* Flash area read */
- ret = pflash_data_read(pfl, offset, width);
- break;
+ return pflash_data_read(pfl, offset, width);
case 0x90:
/* flash ID read */
- switch (boff) {
+ switch (device_addr & 0xFF) {
case 0x00:
+ ret = pfl->ident0;
+ break;
case 0x01:
- ret = boff & 0x01 ? pfl->ident1 : pfl->ident0;
+ ret = pfl->ident1;
break;
case 0x02:
ret = 0x00; /* Pretend all sectors are unprotected */
break;
case 0x0E:
case 0x0F:
- ret = boff & 0x01 ? pfl->ident3 : pfl->ident2;
+ ret = device_addr & 0x01 ? pfl->ident3 : pfl->ident2;
if (ret != (uint8_t)-1) {
break;
}
/* Fall through to data read. */
default:
- ret = pflash_data_read(pfl, offset, width);
+ return pflash_data_read(pfl, offset, width);
}
- DPRINTF("%s: ID " TARGET_FMT_plx " %" PRIx64 "\n", __func__, boff, ret);
+ ret *= pfl->interleave_multiplier;
+ DPRINTF("%s: ID " TARGET_FMT_plx " %" PRIx64 "\n",
+ __func__, device_addr & 0xFF, ret);
break;
case 0xA0:
case 0x10:
@@ -250,8 +254,8 @@ static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
break;
case 0x98:
/* CFI query mode */
- if (boff < sizeof(pfl->cfi_table)) {
- ret = pfl->cfi_table[boff];
+ if (device_addr < sizeof(pfl->cfi_table)) {
+ ret = pfl->interleave_multiplier * pfl->cfi_table[device_addr];
} else {
ret = 0;
}
@@ -279,30 +283,36 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
unsigned int width)
{
PFlashCFI02 *pfl = opaque;
- hwaddr boff;
uint8_t *p;
uint8_t cmd;
cmd = value;
- if (pfl->cmd != 0xA0 && cmd == 0xF0) {
-#if 0
- DPRINTF("%s: flash reset asked (%02x %02x)\n",
- __func__, pfl->cmd, cmd);
-#endif
- goto reset_flash;
+ if (pfl->cmd != 0xA0) {
+ if (value != pfl->interleave_multiplier * cmd) {
+ DPRINTF("%s: cmd 0x%02x not sent to all devices: expected="
+ "0x%0*" PRIx64 " actual=0x%0*" PRIx64 "\n",
+ __func__, cmd,
+ pfl->bank_width * 2, pfl->interleave_multiplier * cmd,
+ pfl->bank_width * 2, value);
+ }
+
+ if (cmd == 0xF0) {
+ goto reset_flash;
+ }
}
+
trace_pflash_write(offset, value, width, pfl->wcycle);
- offset &= pfl->chip_len - 1;
-
- DPRINTF("%s: offset " TARGET_FMT_plx " %08" PRIx64 " %d\n", __func__,
- offset, value, width);
- boff = offset;
- if (pfl->width == 2)
- boff = boff >> 1;
- else if (pfl->width == 4)
- boff = boff >> 2;
- /* Only the least-significant 11 bits are used in most cases. */
- boff &= 0x7FF;
+
+ /* Mask by the total length of the chip to account for alias mappings. */
+ offset &= pfl->total_len - 1;
+
+ DPRINTF("%s: offset " TARGET_FMT_plx " 0x%0*" PRIx64 "\n",
+ __func__, offset, width * 2, value);
+
+ hwaddr device_addr = (offset >> pfl->device_shift);
+ /* Address bits A11 and greater are don't cares for most commands. */
+ unsigned int masked_addr = device_addr & 0x7FF;
+
switch (pfl->wcycle) {
case 0:
/* Set the device in I/O access mode if required */
@@ -311,16 +321,16 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
pfl->read_counter = 0;
/* We're in read mode */
check_unlock0:
- if (boff == 0x55 && cmd == 0x98) {
+ if (masked_addr == 0x55 && cmd == 0x98) {
enter_CFI_mode:
/* Enter CFI query mode */
pfl->wcycle = WCYCLE_CFI;
pfl->cmd = 0x98;
return;
}
- if (boff != pfl->unlock_addr0 || cmd != 0xAA) {
- DPRINTF("%s: unlock0 failed " TARGET_FMT_plx " %02x %04x\n",
- __func__, boff, cmd, pfl->unlock_addr0);
+ if (masked_addr != pfl->unlock_addr0 || cmd != 0xAA) {
+ DPRINTF("%s: unlock0 failed %04x %02x %04x\n",
+ __func__, masked_addr, cmd, pfl->unlock_addr0);
goto reset_flash;
}
DPRINTF("%s: unlock sequence started\n", __func__);
@@ -328,18 +338,18 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
case 1:
/* We started an unlock sequence */
check_unlock1:
- if (boff != pfl->unlock_addr1 || cmd != 0x55) {
- DPRINTF("%s: unlock1 failed " TARGET_FMT_plx " %02x\n", __func__,
- boff, cmd);
+ if (masked_addr != pfl->unlock_addr1 || cmd != 0x55) {
+ DPRINTF("%s: unlock1 failed %03x %02x\n", __func__,
+ masked_addr, cmd);
goto reset_flash;
}
DPRINTF("%s: unlock sequence done\n", __func__);
break;
case 2:
/* We finished an unlock sequence */
- if (!pfl->bypass && boff != pfl->unlock_addr0) {
- DPRINTF("%s: command failed " TARGET_FMT_plx " %02x\n", __func__,
- boff, cmd);
+ if (!pfl->bypass && masked_addr != pfl->unlock_addr0) {
+ DPRINTF("%s: command failed %03x %02x\n", __func__,
+ masked_addr, cmd);
goto reset_flash;
}
switch (cmd) {
@@ -390,8 +400,9 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
goto reset_flash;
}
/* We can enter CFI query mode from autoselect mode */
- if (boff == 0x55 && cmd == 0x98)
+ if (masked_addr == 0x55 && cmd == 0x98) {
goto enter_CFI_mode;
+ }
/* No break here */
default:
DPRINTF("%s: invalid write for command %02x\n",
@@ -416,7 +427,7 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
case 5:
switch (cmd) {
case 0x10:
- if (boff != pfl->unlock_addr0) {
+ if (masked_addr != pfl->unlock_addr0) {
DPRINTF("%s: chip erase: invalid address " TARGET_FMT_plx "\n",
__func__, offset);
goto reset_flash;
@@ -424,8 +435,8 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* Chip erase */
DPRINTF("%s: start chip erase\n", __func__);
if (!pfl->ro) {
- memset(pfl->storage, 0xFF, pfl->chip_len);
- pflash_update(pfl, 0, pfl->chip_len);
+ memset(pfl->storage, 0xFF, pfl->total_len);
+ pflash_update(pfl, 0, pfl->total_len);
}
set_dq7(pfl, 0x00);
/* Let's wait 5 seconds before chip erase is done */
@@ -521,22 +532,132 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
return;
}
+ if (pfl->bank_width == 0) {
+ error_setg(errp, "attribute \"width\" not specified or zero.");
+ return;
+ }
+
+ /*
+ * device-width defaults to width and max-device-width defaults to
+ * device-width. Check that the device-width and max-device-width
+ * configurations are supported.
+ */
+ if (pfl->device_width == 0) {
+ pfl->device_width = pfl->bank_width;
+ }
+ if (pfl->max_device_width == 0) {
+ pfl->max_device_width = pfl->device_width;
+ }
+ if (pfl->bank_width % pfl->device_width != 0) {
+ error_setg(errp,
+ "attribute \"width\" (%u) not a multiple of attribute "
+ "\"device-width\" (%u).",
+ pfl->bank_width, pfl->device_width);
+ return;
+ }
+
+ /*
+ * Writing commands to the flash device and reading CFI responses or
+ * status values requires transforming a QEMU device offset into a
+ * flash device address given in terms of the device's maximum width. We
+ * can do this by shifting a QEMU device offset right a constant number of
+ * bits depending on the bank_width, device_width, and max_device_width.
+ *
+ * num_devices = bank_width / device_width is the number of interleaved
+ * flash devices. To compute a device byte address, we need to divide
+ * offset by num_devices (equivalently shift right by log2(num_devices)).
+ * To turn a device byte address into a device word address, we need to
+ * divide by max_device_width (equivalently shift right by
+ * log2(max_device_width)).
+ *
+ * In tabular form.
+ * ==================================================================
+ * bank_width device_width max_device_width num_devices shift
+ * ------------------------------------------------------------------
+ * 1 1 1 1 0
+ * 1 1 2 1 1
+ * 2 1 1 2 1
+ * 2 1 2 2 2
+ * 2 2 2 1 1
+ * 4 1 1 4 2
+ * 4 1 2 4 3
+ * 4 1 4 4 4
+ * 4 2 2 2 2
+ * 4 2 4 2 3
+ * 4 4 4 1 2
+ * ==================================================================
+ */
+ pfl->device_shift = ctz32(pfl->bank_width) - ctz32(pfl->device_width) +
+ ctz32(pfl->max_device_width);
+ pfl->interleave_multiplier = 0;
+ for (unsigned int shift = 0; shift < pfl->bank_width;
+ shift += pfl->device_width) {
+ pfl->interleave_multiplier |= 1 << (shift * 8);
+ }
+
+ uint16_t device_interface_code;
+ if (pfl->max_device_width == 1 && pfl->device_width == 1) {
+ device_interface_code = 0; /* x8 only. */
+ } else if (pfl->max_device_width == 2 &&
+ (pfl->device_width == 1 || pfl->device_width == 2)) {
+ /* XXX: Some devices only support x16, this code doesn't model them. */
+ device_interface_code = 2; /* Supports x8 or x16. */
+ } else if (pfl->max_device_width == 4 && pfl->device_width == 1) {
+ /*
+ * XXX: this is x32-only. The standards I've seen don't specify a value
+ * for x8/x32 but do mention them.
+ */
+ device_interface_code = 3; /* x32 only. */
+ } else if (pfl->max_device_width == 4 &&
+ (pfl->device_width == 2 || pfl->device_width == 4)) {
+ device_interface_code = 4; /* Supports x16 or x32. */
+ } else {
+ error_setg(errp,
+ "unsupported configuration: \"device-width\"=%u "
+ "\"max-device-width\"=%u.",
+ pfl->device_width, pfl->max_device_width);
+ return;
+ }
+
+ pfl->total_len = pfl->sector_len * pfl->nb_blocs;
+
+ /*
+ * If the flash is not a power of 2, then the code for handling multiple
+ * mappings will not work correctly.
+ */
+ if (!is_power_of_2(pfl->total_len)) {
+ error_setg(errp, "total pflash length (%" PRIx64 ") not a power of 2.",
+ pfl->total_len);
+ return;
+ }
+
+ int num_devices = pfl->bank_width / pfl->device_width;
+ uint64_t sector_len_per_device = pfl->sector_len / num_devices;
+ uint64_t device_len = sector_len_per_device * pfl->nb_blocs;
+
+ if (sector_len_per_device & 0xff || sector_len_per_device >= (1 << 24)) {
+ error_setg(errp,
+ "unsupported configuration: sector length per device = "
+ "%" PRIx64 ".",
+ sector_len_per_device);
+ return;
+ }
+
+ memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl),
+ &pflash_cfi02_ops, pfl, pfl->name,
+ pfl->total_len, &local_err);
/* Only 11 bits are used in the comparison. */
pfl->unlock_addr0 &= 0x7FF;
pfl->unlock_addr1 &= 0x7FF;
chip_len = pfl->sector_len * pfl->nb_blocs;
- memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl),
- &pflash_cfi02_ops, pfl, pfl->name,
- chip_len, &local_err);
if (local_err) {
error_propagate(errp, local_err);
return;
}
pfl->storage = memory_region_get_ram_ptr(&pfl->orig_mem);
- pfl->chip_len = chip_len;
if (pfl->blk) {
uint64_t perm;
@@ -566,6 +687,7 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->wcycle = 0;
pfl->cmd = 0;
pfl->status = 0;
+
/* Hardcoded CFI table (mostly from SG29 Spansion flash) */
/* Standard "QRY" string */
pfl->cfi_table[0x10] = 'Q';
@@ -591,8 +713,8 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->cfi_table[0x1D] = 0x00;
/* Vpp max (no Vpp pin) */
pfl->cfi_table[0x1E] = 0x00;
- /* Reserved */
- pfl->cfi_table[0x1F] = 0x07;
+ /* Timeout per single byte/word write (16 us) */
+ pfl->cfi_table[0x1F] = 0x04;
/* Timeout for min size buffer write (NA) */
pfl->cfi_table[0x20] = 0x00;
/* Typical timeout for block erase (512 ms) */
@@ -608,13 +730,13 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
/* Max timeout for chip erase */
pfl->cfi_table[0x26] = 0x0D;
/* Device size */
- pfl->cfi_table[0x27] = ctz32(chip_len);
- /* Flash device interface (8 & 16 bits) */
- pfl->cfi_table[0x28] = 0x02;
- pfl->cfi_table[0x29] = 0x00;
+ pfl->cfi_table[0x27] = ctz32(device_len);
+ /* Flash device interface */
+ pfl->cfi_table[0x28] = device_interface_code;
+ pfl->cfi_table[0x29] = device_interface_code >> 8;
/* Max number of bytes in multi-bytes write */
/* XXX: disable buffered write as it's not supported */
- // pfl->cfi_table[0x2A] = 0x05;
+ /* pfl->cfi_table[0x2A] = 0x05; */
pfl->cfi_table[0x2A] = 0x00;
pfl->cfi_table[0x2B] = 0x00;
/* Number of erase block regions (uniform) */
@@ -622,8 +744,8 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
/* Erase block region 1 */
pfl->cfi_table[0x2D] = pfl->nb_blocs - 1;
pfl->cfi_table[0x2E] = (pfl->nb_blocs - 1) >> 8;
- pfl->cfi_table[0x2F] = pfl->sector_len >> 8;
- pfl->cfi_table[0x30] = pfl->sector_len >> 16;
+ pfl->cfi_table[0x2F] = sector_len_per_device >> 8;
+ pfl->cfi_table[0x30] = sector_len_per_device >> 16;
/* Extended */
pfl->cfi_table[0x31] = 'P';
@@ -648,7 +770,9 @@ static Property pflash_cfi02_properties[] = {
DEFINE_PROP_DRIVE("drive", PFlashCFI02, blk),
DEFINE_PROP_UINT32("num-blocks", PFlashCFI02, nb_blocs, 0),
DEFINE_PROP_UINT32("sector-length", PFlashCFI02, sector_len, 0),
- DEFINE_PROP_UINT8("width", PFlashCFI02, width, 0),
+ DEFINE_PROP_UINT8("width", PFlashCFI02, bank_width, 0),
+ DEFINE_PROP_UINT8("device-width", PFlashCFI02, device_width, 0),
+ DEFINE_PROP_UINT8("max-device-width", PFlashCFI02, max_device_width, 0),
DEFINE_PROP_UINT8("mappings", PFlashCFI02, mappings, 0),
DEFINE_PROP_UINT8("big-endian", PFlashCFI02, be, 0),
DEFINE_PROP_UINT16("id0", PFlashCFI02, ident0, 0),
@@ -696,7 +820,7 @@ PFlashCFI02 *pflash_cfi02_register(hwaddr base,
hwaddr size,
BlockBackend *blk,
uint32_t sector_len,
- int nb_mappings, int width,
+ int nb_mappings, int bank_width,
uint16_t id0, uint16_t id1,
uint16_t id2, uint16_t id3,
uint16_t unlock_addr0,
@@ -711,7 +835,7 @@ PFlashCFI02 *pflash_cfi02_register(hwaddr base,
assert(size % sector_len == 0);
qdev_prop_set_uint32(dev, "num-blocks", size / sector_len);
qdev_prop_set_uint32(dev, "sector-length", sector_len);
- qdev_prop_set_uint8(dev, "width", width);
+ qdev_prop_set_uint8(dev, "width", bank_width);
qdev_prop_set_uint8(dev, "mappings", nb_mappings);
qdev_prop_set_uint8(dev, "big-endian", !!be);
qdev_prop_set_uint16(dev, "id0", id0);
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index b91bb66a79..4d621e584d 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -21,10 +21,15 @@
#define MP_FLASH_SIZE_MAX (32 * 1024 * 1024)
#define BASE_ADDR (0x100000000ULL - MP_FLASH_SIZE_MAX)
-#define FLASH_WIDTH 2
-#define CFI_ADDR (FLASH_WIDTH * 0x55)
-#define UNLOCK0_ADDR (FLASH_WIDTH * 0x555)
-#define UNLOCK1_ADDR (FLASH_WIDTH * 0x2AA)
+/* Use a newtype to keep flash addresses separate from byte addresses. */
+typedef struct {
+ uint64_t addr;
+} faddr;
+#define FLASH_ADDR(x) ((faddr) { .addr = (x) })
+
+#define CFI_ADDR FLASH_ADDR(0x55)
+#define UNLOCK0_ADDR FLASH_ADDR(0x555)
+#define UNLOCK1_ADDR FLASH_ADDR(0x2AA)
#define CFI_CMD 0x98
#define UNLOCK0_CMD 0xAA
@@ -37,168 +42,332 @@
#define UNLOCK_BYPASS_CMD 0x20
#define UNLOCK_BYPASS_RESET_CMD 0x00
+typedef struct {
+ int bank_width;
+ int device_width;
+ int max_device_width;
+} FlashConfig;
+
static char image_path[] = "/tmp/qtest.XXXXXX";
-static inline void flash_write(uint64_t byte_addr, uint16_t data)
+/*
+ * The pflash implementation allows some parameters to be unspecified. We want
+ * to test those configurations but we also need to know the real values in
+ * our testing code. So after we launch qemu, we'll need a new FlashConfig
+ * with the correct values filled in.
+ */
+static FlashConfig expand_config_defaults(const FlashConfig *c)
{
- qtest_writew(global_qtest, BASE_ADDR + byte_addr, data);
+ FlashConfig ret = *c;
+
+ if (ret.device_width == 0) {
+ ret.device_width = ret.bank_width;
+ }
+ if (ret.max_device_width == 0) {
+ ret.max_device_width = ret.device_width;
+ }
+ return ret;
+}
+
+/*
+ * Return a bit mask suitable for extracting the least significant
+ * status/query response from an interleaved response.
+ */
+static inline uint64_t device_mask(const FlashConfig *c)
+{
+ if (c->device_width == 8) {
+ return (uint64_t)-1;
+ }
+ return (1ULL << (c->device_width * 8)) - 1ULL;
+}
+
+/*
+ * Return a bit mask exactly as long as the bank_width.
+ */
+static inline uint64_t bank_mask(const FlashConfig *c)
+{
+ if (c->bank_width == 8) {
+ return (uint64_t)-1;
+ }
+ return (1ULL << (c->bank_width * 8)) - 1ULL;
+}
+
+static inline void flash_write(const FlashConfig *c, uint64_t byte_addr,
+ uint64_t data)
+{
+ /* Sanity check our tests. */
+ assert((data & ~bank_mask(c)) == 0);
+ uint64_t addr = BASE_ADDR + byte_addr;
+ switch (c->bank_width) {
+ case 1:
+ qtest_writeb(global_qtest, addr, data);
+ break;
+ case 2:
+ qtest_writew(global_qtest, addr, data);
+ break;
+ case 4:
+ qtest_writel(global_qtest, addr, data);
+ break;
+ case 8:
+ qtest_writeq(global_qtest, addr, data);
+ break;
+ default:
+ abort();
+ }
+}
+
+static inline uint64_t flash_read(const FlashConfig *c, uint64_t byte_addr)
+{
+ uint64_t addr = BASE_ADDR + byte_addr;
+ switch (c->bank_width) {
+ case 1:
+ return qtest_readb(global_qtest, addr);
+ case 2:
+ return qtest_readw(global_qtest, addr);
+ case 4:
+ return qtest_readl(global_qtest, addr);
+ case 8:
+ return qtest_readq(global_qtest, addr);
+ default:
+ abort();
+ }
+}
+
+/*
+ * Convert a flash address expressed in the maximum width of the device as a
+ * byte address.
+ */
+static inline uint64_t as_byte_addr(const FlashConfig *c, faddr flash_addr)
+{
+ /*
+ * Command addresses are always given as addresses in the maximum
+ * supported bus size for the flash chip. So an x8/x16 chip in x8 mode
+ * uses addresses 0xAAA and 0x555 to unlock because the least significant
+ * bit is ignored. (0x555 rather than 0x554 is traditional.)
+ *
+ * Interleaving flash chips use the least significant bits of a byte
+ * address to refer to data from the individual chips. Two interleaved x8
+ * devices would use command addresses 0xAAA and 0x554. Two interleaved
+ * x16 devices would use 0x1554 and 0xAA8.
+ *
+ * More exotic configurations are possible. Two interleaved x8/x16 devices
+ * in x8 mode would also use 0x1554 and 0xAA8.
+ *
+ * In general we need to multiply an address by the number of devices,
+ * which is bank_width / device_width, and multiply that by the maximum
+ * device width.
+ */
+ int num_devices = c->bank_width / c->device_width;
+ return flash_addr.addr * (num_devices * c->max_device_width);
+}
+
+/*
+ * Return the command value or expected status replicated across all devices.
+ */
+static inline uint64_t replicate(const FlashConfig *c, uint64_t data)
+{
+ /* Sanity check our tests. */
+ assert((data & ~device_mask(c)) == 0);
+ for (int i = c->device_width; i < c->bank_width; i += c->device_width) {
+ data |= data << (c->device_width * 8);
+ }
+ return data;
+}
+
+static inline void flash_cmd(const FlashConfig *c, faddr cmd_addr,
+ uint8_t cmd)
+{
+ flash_write(c, as_byte_addr(c, cmd_addr), replicate(c, cmd));
+}
+
+static inline uint64_t flash_query(const FlashConfig *c, faddr query_addr)
+{
+ return flash_read(c, as_byte_addr(c, query_addr));
}
-static inline uint16_t flash_read(uint64_t byte_addr)
+static inline uint64_t flash_query_1(const FlashConfig *c, faddr query_addr)
{
- return qtest_readw(global_qtest, BASE_ADDR + byte_addr);
+ return flash_query(c, query_addr) & device_mask(c);
}
-static void unlock(void)
+static void unlock(const FlashConfig *c)
{
- flash_write(UNLOCK0_ADDR, UNLOCK0_CMD);
- flash_write(UNLOCK1_ADDR, UNLOCK1_CMD);
+ flash_cmd(c, UNLOCK0_ADDR, UNLOCK0_CMD);
+ flash_cmd(c, UNLOCK1_ADDR, UNLOCK1_CMD);
}
-static void reset(void)
+static void reset(const FlashConfig *c)
{
- flash_write(0, RESET_CMD);
+ flash_cmd(c, FLASH_ADDR(0), RESET_CMD);
}
-static void sector_erase(uint64_t byte_addr)
+static void sector_erase(const FlashConfig *c, uint64_t byte_addr)
{
- unlock();
- flash_write(UNLOCK0_ADDR, 0x80);
- unlock();
- flash_write(byte_addr, SECTOR_ERASE_CMD);
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, 0x80);
+ unlock(c);
+ flash_write(c, byte_addr, replicate(c, SECTOR_ERASE_CMD));
}
-static void wait_for_completion(uint64_t byte_addr)
+static void wait_for_completion(const FlashConfig *c, uint64_t byte_addr)
{
/* If DQ6 is toggling, step the clock and ensure the toggle stops. */
- if ((flash_read(byte_addr) & 0x40) ^ (flash_read(byte_addr) & 0x40)) {
+ const uint64_t dq6 = replicate(c, 0x40);
+ if ((flash_read(c, byte_addr) & dq6) ^ (flash_read(c, byte_addr) & dq6)) {
/* Wait for erase or program to finish. */
clock_step_next();
/* Ensure that DQ6 has stopped toggling. */
- g_assert_cmpint(flash_read(byte_addr), ==, flash_read(byte_addr));
+ g_assert_cmpint(flash_read(c, byte_addr), ==, flash_read(c, byte_addr));
}
}
-static void bypass_program(uint64_t byte_addr, uint16_t data)
+static void bypass_program(const FlashConfig *c, uint64_t byte_addr,
+ uint16_t data)
{
- flash_write(UNLOCK0_ADDR, PROGRAM_CMD);
- flash_write(byte_addr, data);
+ flash_cmd(c, UNLOCK0_ADDR, PROGRAM_CMD);
+ flash_write(c, byte_addr, data);
/*
* Data isn't valid until DQ6 stops toggling. We don't model this as
* writes are immediate, but if this changes in the future, we can wait
* until the program is complete.
*/
- wait_for_completion(byte_addr);
+ wait_for_completion(c, byte_addr);
}
-static void program(uint64_t byte_addr, uint16_t data)
+static void program(const FlashConfig *c, uint64_t byte_addr, uint16_t data)
{
- unlock();
- bypass_program(byte_addr, data);
+ unlock(c);
+ bypass_program(c, byte_addr, data);
}
-static void chip_erase(void)
+static void chip_erase(const FlashConfig *c)
{
- unlock();
- flash_write(UNLOCK0_ADDR, 0x80);
- unlock();
- flash_write(UNLOCK0_ADDR, SECTOR_ERASE_CMD);
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, 0x80);
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, CHIP_ERASE_CMD);
}
-static void test_flash(void)
+static void test_flash(const void *opaque)
{
- global_qtest = qtest_initf("-M musicpal,accel=qtest "
- "-drive if=pflash,file=%s,format=raw,copy-on-read",
- image_path);
+ const FlashConfig *config = opaque;
+ global_qtest = qtest_initf("-M musicpal,accel=qtest"
+ " -drive if=pflash,file=%s,format=raw,"
+ "copy-on-read"
+ " -global driver=cfi.pflash02,"
+ "property=device-width,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=max-device-width,value=%d",
+ image_path,
+ config->device_width,
+ config->max_device_width);
+
+ const FlashConfig explicit_config = expand_config_defaults(config);
+ const FlashConfig *c = &explicit_config;
+
/* Check the IDs. */
- unlock();
- flash_write(UNLOCK0_ADDR, AUTOSELECT_CMD);
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0000), ==, 0x00BF);
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0001), ==, 0x236D);
- reset();
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, AUTOSELECT_CMD);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
+ if (c->device_width >= 2) {
+ /*
+ * XXX: The ID returned by the musicpal flash chip is 16 bits which
+ * wouldn't happen with an 8-bit device. It would probably be best to
+ * prohibit addresses larger than the device width in pflash_cfi02.c,
+ * but then we couldn't test smaller device widths at all.
+ */
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(1)), ==,
+ replicate(c, 0x236D));
+ }
+ reset(c);
/* Check the erase blocks. */
- flash_write(CFI_ADDR, CFI_CMD);
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x10), ==, 'Q');
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x11), ==, 'R');
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x12), ==, 'Y');
+ flash_cmd(c, CFI_ADDR, CFI_CMD);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x10)), ==, replicate(c, 'Q'));
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x11)), ==, replicate(c, 'R'));
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x12)), ==, replicate(c, 'Y'));
/* Num erase regions. */
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x2C), >=, 1);
- uint32_t nb_sectors = flash_read(FLASH_WIDTH * 0x2D) +
- (flash_read(FLASH_WIDTH * 0x2E) << 8) + 1;
- uint32_t sector_len = (flash_read(FLASH_WIDTH * 0x2F) << 8) +
- (flash_read(FLASH_WIDTH * 0x30) << 16);
- reset();
+ g_assert_cmpint(flash_query_1(c, FLASH_ADDR(0x2C)), >=, 1);
+ uint32_t nb_sectors = flash_query_1(c, FLASH_ADDR(0x2D)) +
+ (flash_query_1(c, FLASH_ADDR(0x2E)) << 8) + 1;
+ uint32_t sector_len = (flash_query_1(c, FLASH_ADDR(0x2F)) << 8) +
+ (flash_query_1(c, FLASH_ADDR(0x30)) << 16);
+ reset(c);
+ const uint64_t dq7 = replicate(c, 0x80);
+ const uint64_t dq6 = replicate(c, 0x40);
/* Erase and program sector. */
for (uint32_t i = 0; i < nb_sectors; ++i) {
uint64_t byte_addr = i * sector_len;
- sector_erase(byte_addr);
+ sector_erase(c, byte_addr);
/* Read toggle. */
- uint16_t status0 = flash_read(byte_addr);
+ uint64_t status0 = flash_read(c, byte_addr);
/* DQ7 is 0 during an erase. */
- g_assert_cmpint(status0 & 0x80, ==, 0);
- uint16_t status1 = flash_read(byte_addr);
+ g_assert_cmpint(status0 & dq7, ==, 0);
+ uint64_t status1 = flash_read(c, byte_addr);
/* DQ6 toggles during an erase. */
- g_assert_cmpint(status0 & 0x40, !=, status1 & 0x40);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
/* Wait for erase to complete. */
clock_step_next();
/* Ensure DQ6 has stopped toggling. */
- g_assert_cmpint(flash_read(byte_addr), ==, flash_read(byte_addr));
+ g_assert_cmpint(flash_read(c, byte_addr), ==, flash_read(c, byte_addr));
/* Now the data should be valid. */
- g_assert_cmpint(flash_read(byte_addr), ==, 0xFFFF);
+ g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
/* Program a bit pattern. */
- program(byte_addr, 0x5555);
- g_assert_cmpint(flash_read(byte_addr), ==, 0x5555);
- program(byte_addr, 0xAA55);
- g_assert_cmpint(flash_read(byte_addr), ==, 0x0055);
+ program(c, byte_addr, 0x55);
+ g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x55);
+ program(c, byte_addr, 0xA5);
+ g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x05);
}
/* Erase the chip. */
- chip_erase();
+ chip_erase(c);
/* Read toggle. */
- uint16_t status0 = flash_read(0);
+ uint64_t status0 = flash_read(c, 0);
/* DQ7 is 0 during an erase. */
- g_assert_cmpint(status0 & 0x80, ==, 0);
- uint16_t status1 = flash_read(0);
+ g_assert_cmpint(status0 & dq7, ==, 0);
+ uint64_t status1 = flash_read(c, 0);
/* DQ6 toggles during an erase. */
- g_assert_cmpint(status0 & 0x40, !=, status1 & 0x40);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
/* Wait for erase to complete. */
clock_step_next();
/* Ensure DQ6 has stopped toggling. */
- g_assert_cmpint(flash_read(0), ==, flash_read(0));
+ g_assert_cmpint(flash_read(c, 0), ==, flash_read(c, 0));
/* Now the data should be valid. */
- g_assert_cmpint(flash_read(0), ==, 0xFFFF);
+
+ for (uint32_t i = 0; i < nb_sectors; ++i) {
+ uint64_t byte_addr = i * sector_len;
+ g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
+ }
/* Unlock bypass */
- unlock();
- flash_write(UNLOCK0_ADDR, UNLOCK_BYPASS_CMD);
- bypass_program(0, 0x0123);
- bypass_program(2, 0x4567);
- bypass_program(4, 0x89AB);
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, UNLOCK_BYPASS_CMD);
+ bypass_program(c, 0 * c->bank_width, 0x01);
+ bypass_program(c, 1 * c->bank_width, 0x23);
+ bypass_program(c, 2 * c->bank_width, 0x45);
/*
* Test that bypass programming, unlike normal programming can use any
* address for the PROGRAM_CMD.
*/
- flash_write(6, PROGRAM_CMD);
- flash_write(6, 0xCDEF);
- wait_for_completion(6);
- flash_write(0, UNLOCK_BYPASS_RESET_CMD);
- bypass_program(8, 0x55AA); /* Should fail. */
- g_assert_cmpint(flash_read(0), ==, 0x0123);
- g_assert_cmpint(flash_read(2), ==, 0x4567);
- g_assert_cmpint(flash_read(4), ==, 0x89AB);
- g_assert_cmpint(flash_read(6), ==, 0xCDEF);
- g_assert_cmpint(flash_read(8), ==, 0xFFFF);
+ flash_cmd(c, FLASH_ADDR(3 * c->bank_width), PROGRAM_CMD);
+ flash_write(c, 3 * c->bank_width, 0x67);
+ wait_for_completion(c, 3 * c->bank_width);
+ flash_cmd(c, FLASH_ADDR(0), UNLOCK_BYPASS_RESET_CMD);
+ bypass_program(c, 4 * c->bank_width, 0x89); /* Should fail. */
+ g_assert_cmpint(flash_read(c, 0 * c->bank_width), ==, 0x01);
+ g_assert_cmpint(flash_read(c, 1 * c->bank_width), ==, 0x23);
+ g_assert_cmpint(flash_read(c, 2 * c->bank_width), ==, 0x45);
+ g_assert_cmpint(flash_read(c, 3 * c->bank_width), ==, 0x67);
+ g_assert_cmpint(flash_read(c, 4 * c->bank_width), ==, bank_mask(c));
/* Test ignored high order bits of address. */
- flash_write(FLASH_WIDTH * 0x5555, UNLOCK0_CMD);
- flash_write(FLASH_WIDTH * 0x2AAA, UNLOCK1_CMD);
- flash_write(FLASH_WIDTH * 0x5555, AUTOSELECT_CMD);
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0000), ==, 0x00BF);
- g_assert_cmpint(flash_read(FLASH_WIDTH * 0x0001), ==, 0x236D);
- reset();
+ flash_cmd(c, FLASH_ADDR(0x5555), UNLOCK0_CMD);
+ flash_cmd(c, FLASH_ADDR(0x2AAA), UNLOCK1_CMD);
+ flash_cmd(c, FLASH_ADDR(0x5555), AUTOSELECT_CMD);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
+ reset(c);
qtest_quit(global_qtest);
}
@@ -208,6 +377,61 @@ static void cleanup(void *opaque)
unlink(image_path);
}
+/*
+ * XXX: Tests are limited to bank_width = 2 for now because that's what
+ * hw/arm/musicpal.c has.
+ */
+static const FlashConfig configuration[] = {
+ /* One x16 device. */
+ {
+ .bank_width = 2,
+ .device_width = 2,
+ .max_device_width = 2,
+ },
+ /* Implicitly one x16 device. */
+ {
+ .bank_width = 2,
+ .device_width = 0,
+ .max_device_width = 0,
+ },
+ /* Implicitly one x16 device. */
+ {
+ .bank_width = 2,
+ .device_width = 2,
+ .max_device_width = 0,
+ },
+ /* Interleave two x8 devices. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .max_device_width = 1,
+ },
+ /* Interleave two implicit x8 devices. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .max_device_width = 0,
+ },
+ /* Interleave two x8/x16 devices in x8 mode. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .max_device_width = 2,
+ },
+ /* One x16/x32 device in x16 mode. */
+ {
+ .bank_width = 2,
+ .device_width = 2,
+ .max_device_width = 4,
+ },
+ /* Two x8/x32 devices in x8 mode; I am not sure if such devices exist. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .max_device_width = 4,
+ },
+};
+
int main(int argc, char **argv)
{
int fd = mkstemp(image_path);
@@ -226,7 +450,17 @@ int main(int argc, char **argv)
qtest_add_abrt_handler(cleanup, NULL);
g_test_init(&argc, &argv, NULL);
- qtest_add_func("pflash-cfi02", test_flash);
+
+ size_t nb_configurations = sizeof configuration / sizeof configuration[0];
+ for (size_t i = 0; i < nb_configurations; ++i) {
+ const FlashConfig *config = &configuration[i];
+ char *path = g_strdup_printf("pflash-cfi02/%d-%d-%d",
+ config->bank_width,
+ config->device_width,
+ config->max_device_width);
+ qtest_add_data_func(path, config, test_flash);
+ g_free(path);
+ }
int result = g_test_run();
cleanup(NULL);
return result;
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 05/10] block/pflash_cfi02: Implement nonuniform sector sizes
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
` (4 preceding siblings ...)
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 04/10] block/pflash_cfi02: Implement intereleaved flash devices Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 06/10] block/pflash_cfi02: Fix CFI in autoselect mode Stephen Checkoway
` (4 subsequent siblings)
10 siblings, 1 reply; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Max Reitz, qemu-block, Stephen Checkoway, Thomas Huth,
Laurent Vivier, Paolo Bonzini
Some flash chips support sectors of different sizes. For example, the
AMD AM29LV160DT has 31 64 kB sectors, one 32 kB sector, two 8 kB
sectors, and a 16 kB sector, in that order. The AM29LV160DB has those in
the reverse order.
The `num-blocks` and `sector-length` properties work exactly as they did
before: a flash device with uniform sector lengths. To get non-uniform
sector lengths for up to four regions, the following properties may be
set
- region 0. `num-blocks0` and `sector-length0`;
- region 1. `num-blocks1` and `sector-length1`;
- region 2. `num-blocks2` and `sector-length2`; and
- region 3. `num-blocks3` and `sector-length3`.
If the uniform and nonuniform properties are set, then both must specify
a flash device with the same total size. It would be better to disallow
both being set, or make `num-blocks0` and `sector-length0` alias
`num-blocks` and `sector-length`, but that would make testing currently
impossible.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 177 ++++++++++++++++++++++++++-----------
tests/pflash-cfi02-test.c | 179 +++++++++++++++++++++++++++++---------
2 files changed, 265 insertions(+), 91 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index 101628b4ec..c4efbe8cdf 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -28,7 +28,6 @@
* - unlock bypass command
* - CFI queries
*
- * It does not implement boot blocs with reduced size
* It does not implement software data protection as found in many real chips
* It does not implement erase suspend/resume commands
* It does not implement multiple sectors erase
@@ -55,6 +54,13 @@ do { \
#define PFLASH_LAZY_ROMD_THRESHOLD 42
+/*
+ * The size of the cfi_table indirectly depends on this and the start of the
+ * PRI table directly depends on it. 4 is the maximum size (and also what
+ * seems common) without changing the PRT table address.
+ */
+#define PFLASH_MAX_ERASE_REGIONS 4
+
/* Special write cycle for CFI queries. */
#define WCYCLE_CFI 7
@@ -64,8 +70,10 @@ struct PFlashCFI02 {
/*< public >*/
BlockBackend *blk;
- uint32_t sector_len;
- uint32_t nb_blocs;
+ uint32_t uniform_nb_blocs;
+ uint32_t uniform_sector_len;
+ uint32_t nb_blocs[PFLASH_MAX_ERASE_REGIONS];
+ uint32_t sector_len[PFLASH_MAX_ERASE_REGIONS];
uint64_t total_len;
uint64_t interleave_multiplier;
uint8_t mappings;
@@ -86,7 +94,7 @@ struct PFlashCFI02 {
uint16_t ident3;
uint16_t unlock_addr0;
uint16_t unlock_addr1;
- uint8_t cfi_table[0x52];
+ uint8_t cfi_table[0x4D];
QEMUTimer timer;
/* The device replicates the flash memory across its memory space. Emulate
* that by having a container (.mem) filled with an array of aliases
@@ -189,6 +197,25 @@ static uint64_t pflash_data_read(PFlashCFI02 *pfl, hwaddr offset,
return ret;
}
+/*
+ * offset should be a byte offset of the QEMU device and _not_ a device
+ * offset.
+ */
+static uint32_t pflash_sector_len(PFlashCFI02 *pfl, hwaddr offset)
+{
+ assert(offset < pfl->total_len);
+ int nb_regions = pfl->cfi_table[0x2C];
+ hwaddr addr = 0;
+ for (int i = 0; i < nb_regions; ++i) {
+ uint64_t region_size = (uint64_t)pfl->nb_blocs[i] * pfl->sector_len[i];
+ if (addr <= offset && offset < addr + region_size) {
+ return pfl->sector_len[i];
+ }
+ addr += region_size;
+ }
+ abort();
+}
+
static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
{
PFlashCFI02 *pfl = opaque;
@@ -285,6 +312,7 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
PFlashCFI02 *pfl = opaque;
uint8_t *p;
uint8_t cmd;
+ uint32_t sector_len;
cmd = value;
if (pfl->cmd != 0xA0) {
@@ -446,12 +474,14 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
case 0x30:
/* Sector erase */
p = pfl->storage;
- offset &= ~(pfl->sector_len - 1);
- DPRINTF("%s: start sector erase at " TARGET_FMT_plx "\n", __func__,
- offset);
+ sector_len = pflash_sector_len(pfl, offset);
+ offset &= ~(sector_len - 1);
+ DPRINTF("%s: start sector erase at %0*" PRIx64 "-%0*" PRIx64 "\n",
+ __func__, pfl->bank_width * 2, offset,
+ pfl->bank_width * 2, offset + sector_len - 1);
if (!pfl->ro) {
- memset(p + offset, 0xFF, pfl->sector_len);
- pflash_update(pfl, offset, pfl->sector_len);
+ memset(p + offset, 0xFF, sector_len);
+ pflash_update(pfl, offset, sector_len);
}
set_dq7(pfl, 0x00);
/* Let's wait 1/2 second before sector erase is done */
@@ -515,15 +545,14 @@ static const MemoryRegionOps pflash_cfi02_ops = {
static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
{
PFlashCFI02 *pfl = PFLASH_CFI02(dev);
- uint32_t chip_len;
int ret;
Error *local_err = NULL;
- if (pfl->sector_len == 0) {
+ if (pfl->uniform_sector_len == 0 && pfl->sector_len[0] == 0) {
error_setg(errp, "attribute \"sector-length\" not specified or zero.");
return;
}
- if (pfl->nb_blocs == 0) {
+ if (pfl->uniform_nb_blocs == 0 && pfl->nb_blocs[0] == 0) {
error_setg(errp, "attribute \"num-blocks\" not specified or zero.");
return;
}
@@ -619,7 +648,53 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
return;
}
- pfl->total_len = pfl->sector_len * pfl->nb_blocs;
+ int num_devices = pfl->bank_width / pfl->device_width;
+ int nb_regions;
+ pfl->total_len = 0;
+ for (nb_regions = 0; nb_regions < PFLASH_MAX_ERASE_REGIONS; ++nb_regions) {
+ if (pfl->nb_blocs[nb_regions] == 0) {
+ break;
+ }
+ uint64_t sector_len_per_device = pfl->sector_len[nb_regions] /
+ num_devices;
+
+ /*
+ * The size of each flash sector must be a power of 2 and it must be
+ * aligned at the same power of 2.
+ */
+ if (sector_len_per_device & 0xff ||
+ sector_len_per_device >= (1 << 24) ||
+ !is_power_of_2(sector_len_per_device))
+ {
+ error_setg(errp, "unsupported configuration: "
+ "sector length[%d] per device = %" PRIx64 ".",
+ nb_regions, sector_len_per_device);
+ return;
+ }
+ if ((pfl->total_len / num_devices) & (sector_len_per_device - 1)) {
+ error_setg(errp, "unsupported configuration: "
+ "flash region %d not correctly aligned.",
+ nb_regions);
+ return;
+ }
+
+ pfl->total_len += (uint64_t)pfl->sector_len[nb_regions] *
+ pfl->nb_blocs[nb_regions];
+ }
+
+ uint64_t uniform_len = (uint64_t)pfl->uniform_nb_blocs *
+ pfl->uniform_sector_len;
+ if (nb_regions == 0) {
+ nb_regions = 1;
+ pfl->nb_blocs[0] = pfl->uniform_nb_blocs;
+ pfl->sector_len[0] = pfl->uniform_sector_len;
+ pfl->total_len = uniform_len;
+ } else if (uniform_len != 0 && uniform_len != pfl->total_len) {
+ error_setg(errp, "\"num-blocks\"*\"sector-length\" "
+ "different from \"num-blocks0\"*\'sector-length0\" + ... + "
+ "\"num-blocks3\"*\"sector-length3\"");
+ return;
+ }
/*
* If the flash is not a power of 2, then the code for handling multiple
@@ -631,18 +706,6 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
return;
}
- int num_devices = pfl->bank_width / pfl->device_width;
- uint64_t sector_len_per_device = pfl->sector_len / num_devices;
- uint64_t device_len = sector_len_per_device * pfl->nb_blocs;
-
- if (sector_len_per_device & 0xff || sector_len_per_device >= (1 << 24)) {
- error_setg(errp,
- "unsupported configuration: sector length per device = "
- "%" PRIx64 ".",
- sector_len_per_device);
- return;
- }
-
memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl),
&pflash_cfi02_ops, pfl, pfl->name,
pfl->total_len, &local_err);
@@ -650,8 +713,6 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->unlock_addr0 &= 0x7FF;
pfl->unlock_addr1 &= 0x7FF;
- chip_len = pfl->sector_len * pfl->nb_blocs;
-
if (local_err) {
error_propagate(errp, local_err);
return;
@@ -672,8 +733,8 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
}
if (pfl->blk) {
- if (!blk_check_size_and_read_all(pfl->blk, pfl->storage, chip_len,
- errp)) {
+ if (!blk_check_size_and_read_all(pfl->blk, pfl->storage,
+ pfl->total_len, errp)) {
vmstate_unregister_ram(&pfl->orig_mem, DEVICE(pfl));
return;
}
@@ -697,7 +758,7 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->cfi_table[0x13] = 0x02;
pfl->cfi_table[0x14] = 0x00;
/* Primary extended table address */
- pfl->cfi_table[0x15] = 0x31;
+ pfl->cfi_table[0x15] = 0x40;
pfl->cfi_table[0x16] = 0x00;
/* Alternate command set (none) */
pfl->cfi_table[0x17] = 0x00;
@@ -730,7 +791,7 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
/* Max timeout for chip erase */
pfl->cfi_table[0x26] = 0x0D;
/* Device size */
- pfl->cfi_table[0x27] = ctz32(device_len);
+ pfl->cfi_table[0x27] = ctz32(pfl->total_len / num_devices);
/* Flash device interface */
pfl->cfi_table[0x28] = device_interface_code;
pfl->cfi_table[0x29] = device_interface_code >> 8;
@@ -739,37 +800,49 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
/* pfl->cfi_table[0x2A] = 0x05; */
pfl->cfi_table[0x2A] = 0x00;
pfl->cfi_table[0x2B] = 0x00;
- /* Number of erase block regions (uniform) */
- pfl->cfi_table[0x2C] = 0x01;
- /* Erase block region 1 */
- pfl->cfi_table[0x2D] = pfl->nb_blocs - 1;
- pfl->cfi_table[0x2E] = (pfl->nb_blocs - 1) >> 8;
- pfl->cfi_table[0x2F] = sector_len_per_device >> 8;
- pfl->cfi_table[0x30] = sector_len_per_device >> 16;
+ /* Number of erase block regions */
+ pfl->cfi_table[0x2C] = nb_regions;
+ /* Erase block regions */
+ for (int i = 0; i < nb_regions; ++i) {
+ uint32_t sector_len_per_device = pfl->sector_len[i] / num_devices;
+ pfl->cfi_table[0x2D + 4 * i] = pfl->nb_blocs[i] - 1;
+ pfl->cfi_table[0x2E + 4 * i] = (pfl->nb_blocs[i] - 1) >> 8;
+ pfl->cfi_table[0x2F + 4 * i] = sector_len_per_device >> 8;
+ pfl->cfi_table[0x30 + 4 * i] = sector_len_per_device >> 16;
+ }
/* Extended */
- pfl->cfi_table[0x31] = 'P';
- pfl->cfi_table[0x32] = 'R';
- pfl->cfi_table[0x33] = 'I';
+ pfl->cfi_table[0x40] = 'P';
+ pfl->cfi_table[0x41] = 'R';
+ pfl->cfi_table[0x42] = 'I';
- pfl->cfi_table[0x34] = '1';
- pfl->cfi_table[0x35] = '0';
+ pfl->cfi_table[0x43] = '1'; /* version 1.0 */
+ pfl->cfi_table[0x44] = '0';
- pfl->cfi_table[0x36] = 0x00;
- pfl->cfi_table[0x37] = 0x00;
- pfl->cfi_table[0x38] = 0x00;
- pfl->cfi_table[0x39] = 0x00;
+ pfl->cfi_table[0x45] = 0x00; /* Address sensitive unlock required. */
+ pfl->cfi_table[0x46] = 0x00; /* Erase suspend not supported. */
+ pfl->cfi_table[0x47] = 0x00; /* Sector protect not supported. */
+ pfl->cfi_table[0x48] = 0x00; /* Temporary sector unprotect not supported. */
- pfl->cfi_table[0x3a] = 0x00;
+ pfl->cfi_table[0x49] = 0x00; /* Sector protect/unprotect scheme. */
- pfl->cfi_table[0x3b] = 0x00;
- pfl->cfi_table[0x3c] = 0x00;
+ pfl->cfi_table[0x4a] = 0x00; /* Simultaneous operation not supported. */
+ pfl->cfi_table[0x4b] = 0x00; /* Burst mode not supported. */
+ pfl->cfi_table[0x4c] = 0x00; /* Page mode not supported. */
}
static Property pflash_cfi02_properties[] = {
DEFINE_PROP_DRIVE("drive", PFlashCFI02, blk),
- DEFINE_PROP_UINT32("num-blocks", PFlashCFI02, nb_blocs, 0),
- DEFINE_PROP_UINT32("sector-length", PFlashCFI02, sector_len, 0),
+ DEFINE_PROP_UINT32("num-blocks", PFlashCFI02, uniform_nb_blocs, 0),
+ DEFINE_PROP_UINT32("sector-length", PFlashCFI02, uniform_sector_len, 0),
+ DEFINE_PROP_UINT32("num-blocks0", PFlashCFI02, nb_blocs[0], 0),
+ DEFINE_PROP_UINT32("sector-length0", PFlashCFI02, sector_len[0], 0),
+ DEFINE_PROP_UINT32("num-blocks1", PFlashCFI02, nb_blocs[1], 0),
+ DEFINE_PROP_UINT32("sector-length1", PFlashCFI02, sector_len[1], 0),
+ DEFINE_PROP_UINT32("num-blocks2", PFlashCFI02, nb_blocs[2], 0),
+ DEFINE_PROP_UINT32("sector-length2", PFlashCFI02, sector_len[2], 0),
+ DEFINE_PROP_UINT32("num-blocks3", PFlashCFI02, nb_blocs[3], 0),
+ DEFINE_PROP_UINT32("sector-length3", PFlashCFI02, sector_len[3], 0),
DEFINE_PROP_UINT8("width", PFlashCFI02, bank_width, 0),
DEFINE_PROP_UINT8("device-width", PFlashCFI02, device_width, 0),
DEFINE_PROP_UINT8("max-device-width", PFlashCFI02, max_device_width, 0),
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index 4d621e584d..dc85783a6a 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -21,6 +21,9 @@
#define MP_FLASH_SIZE_MAX (32 * 1024 * 1024)
#define BASE_ADDR (0x100000000ULL - MP_FLASH_SIZE_MAX)
+#define UNIFORM_FLASH_SIZE (8 * 1024 * 1024)
+#define UNIFORM_FLASH_SECTOR_SIZE (64 * 1024)
+
/* Use a newtype to keep flash addresses separate from byte addresses. */
typedef struct {
uint64_t addr;
@@ -43,9 +46,14 @@ typedef struct {
#define UNLOCK_BYPASS_RESET_CMD 0x00
typedef struct {
+ /* Interleave configuration. */
int bank_width;
int device_width;
int max_device_width;
+
+ /* Nonuniform block size. */
+ int nb_blocs[4];
+ int sector_len[4];
} FlashConfig;
static char image_path[] = "/tmp/qtest.XXXXXX";
@@ -60,12 +68,22 @@ static FlashConfig expand_config_defaults(const FlashConfig *c)
{
FlashConfig ret = *c;
+ if (ret.bank_width == 0) {
+ ret.bank_width = 2;
+ }
if (ret.device_width == 0) {
ret.device_width = ret.bank_width;
}
if (ret.max_device_width == 0) {
ret.max_device_width = ret.device_width;
}
+ if (ret.nb_blocs[0] == 0 && ret.sector_len[0] == 0) {
+ ret.sector_len[0] = UNIFORM_FLASH_SECTOR_SIZE;
+ ret.nb_blocs[0] = UNIFORM_FLASH_SIZE / UNIFORM_FLASH_SECTOR_SIZE;
+ }
+
+ /* XXX: Limitations of test harness. */
+ assert(ret.bank_width == 2);
return ret;
}
@@ -157,8 +175,8 @@ static inline uint64_t as_byte_addr(const FlashConfig *c, faddr flash_addr)
* which is bank_width / device_width, and multiply that by the maximum
* device width.
*/
- int num_devices = c->bank_width / c->device_width;
- return flash_addr.addr * (num_devices * c->max_device_width);
+ int nb_devices = c->bank_width / c->device_width;
+ return flash_addr.addr * (nb_devices * c->max_device_width);
}
/*
@@ -248,22 +266,53 @@ static void chip_erase(const FlashConfig *c)
flash_cmd(c, UNLOCK0_ADDR, CHIP_ERASE_CMD);
}
-static void test_flash(const void *opaque)
+/*
+ * Test flash commands with a variety of device geometry.
+ */
+static void test_geometry(const void *opaque)
{
const FlashConfig *config = opaque;
+ /* Set the properties that are under our control. */
global_qtest = qtest_initf("-M musicpal,accel=qtest"
" -drive if=pflash,file=%s,format=raw,"
"copy-on-read"
+ /* Interleave properties. */
" -global driver=cfi.pflash02,"
"property=device-width,value=%d"
" -global driver=cfi.pflash02,"
- "property=max-device-width,value=%d",
+ "property=max-device-width,value=%d"
+ /* Device geometry properties. */
+ " -global driver=cfi.pflash02,"
+ "property=num-blocks0,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=sector-length0,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=num-blocks1,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=sector-length1,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=num-blocks2,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=sector-length2,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=num-blocks3,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=sector-length3,value=%d",
image_path,
config->device_width,
- config->max_device_width);
+ config->max_device_width,
+ config->nb_blocs[0],
+ config->sector_len[0],
+ config->nb_blocs[1],
+ config->sector_len[1],
+ config->nb_blocs[2],
+ config->sector_len[2],
+ config->nb_blocs[3],
+ config->sector_len[3]);
const FlashConfig explicit_config = expand_config_defaults(config);
const FlashConfig *c = &explicit_config;
+ int nb_devices = c->bank_width / c->device_width;
/* Check the IDs. */
unlock(c);
@@ -287,38 +336,52 @@ static void test_flash(const void *opaque)
g_assert_cmpint(flash_query(c, FLASH_ADDR(0x11)), ==, replicate(c, 'R'));
g_assert_cmpint(flash_query(c, FLASH_ADDR(0x12)), ==, replicate(c, 'Y'));
/* Num erase regions. */
- g_assert_cmpint(flash_query_1(c, FLASH_ADDR(0x2C)), >=, 1);
- uint32_t nb_sectors = flash_query_1(c, FLASH_ADDR(0x2D)) +
- (flash_query_1(c, FLASH_ADDR(0x2E)) << 8) + 1;
- uint32_t sector_len = (flash_query_1(c, FLASH_ADDR(0x2F)) << 8) +
- (flash_query_1(c, FLASH_ADDR(0x30)) << 16);
+ int nb_erase_regions = flash_query_1(c, FLASH_ADDR(0x2C));
+ g_assert_cmpint(nb_erase_regions, ==,
+ !!c->nb_blocs[0] + !!c->nb_blocs[1] + !!c->nb_blocs[2] +
+ !!c->nb_blocs[3]);
reset(c);
-
const uint64_t dq7 = replicate(c, 0x80);
const uint64_t dq6 = replicate(c, 0x40);
- /* Erase and program sector. */
- for (uint32_t i = 0; i < nb_sectors; ++i) {
- uint64_t byte_addr = i * sector_len;
- sector_erase(c, byte_addr);
- /* Read toggle. */
- uint64_t status0 = flash_read(c, byte_addr);
- /* DQ7 is 0 during an erase. */
- g_assert_cmpint(status0 & dq7, ==, 0);
- uint64_t status1 = flash_read(c, byte_addr);
- /* DQ6 toggles during an erase. */
- g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
- /* Wait for erase to complete. */
- clock_step_next();
- /* Ensure DQ6 has stopped toggling. */
- g_assert_cmpint(flash_read(c, byte_addr), ==, flash_read(c, byte_addr));
- /* Now the data should be valid. */
- g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
- /* Program a bit pattern. */
- program(c, byte_addr, 0x55);
- g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x55);
- program(c, byte_addr, 0xA5);
- g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x05);
+ uint64_t byte_addr = 0;
+ for (int region = 0; region < nb_erase_regions; ++region) {
+ uint64_t base = 0x2D + 4 * region;
+ flash_cmd(c, CFI_ADDR, CFI_CMD);
+ uint32_t nb_sectors = flash_query_1(c, FLASH_ADDR(base + 0)) +
+ (flash_query_1(c, FLASH_ADDR(base + 1)) << 8) + 1;
+ uint32_t sector_len = (flash_query_1(c, FLASH_ADDR(base + 2)) << 8) +
+ (flash_query_1(c, FLASH_ADDR(base + 3)) << 16);
+ sector_len *= nb_devices;
+ g_assert_cmpint(nb_sectors, ==, c->nb_blocs[region]);
+ g_assert_cmpint(sector_len, ==, c->sector_len[region]);
+ reset(c);
+
+ /* Erase and program sector. */
+ for (uint32_t i = 0; i < nb_sectors; ++i) {
+ sector_erase(c, byte_addr);
+ /* Read toggle. */
+ uint64_t status0 = flash_read(c, byte_addr);
+ /* DQ7 is 0 during an erase. */
+ g_assert_cmpint(status0 & dq7, ==, 0);
+ uint64_t status1 = flash_read(c, byte_addr);
+ /* DQ6 toggles during an erase. */
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ /* Wait for erase to complete. */
+ clock_step_next();
+ /* Ensure DQ6 has stopped toggling. */
+ g_assert_cmpint(flash_read(c, byte_addr), ==,
+ flash_read(c, byte_addr));
+ /* Now the data should be valid. */
+ g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
+
+ /* Program a bit pattern. */
+ program(c, byte_addr, 0x55);
+ g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x55);
+ program(c, byte_addr, 0xA5);
+ g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x05);
+ byte_addr += sector_len;
+ }
}
/* Erase the chip. */
@@ -336,9 +399,11 @@ static void test_flash(const void *opaque)
g_assert_cmpint(flash_read(c, 0), ==, flash_read(c, 0));
/* Now the data should be valid. */
- for (uint32_t i = 0; i < nb_sectors; ++i) {
- uint64_t byte_addr = i * sector_len;
- g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
+ for (int region = 0; region < nb_erase_regions; ++region) {
+ for (uint32_t i = 0; i < c->nb_blocs[region]; ++i) {
+ uint64_t byte_addr = i * c->sector_len[region];
+ g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
+ }
}
/* Unlock bypass */
@@ -430,6 +495,32 @@ static const FlashConfig configuration[] = {
.device_width = 1,
.max_device_width = 4,
},
+ /* Nonuniform sectors (top boot). */
+ {
+ .bank_width = 2,
+ .nb_blocs = { 127, 1, 2, 1 },
+ .sector_len = { 0x10000, 0x08000, 0x02000, 0x04000 },
+ },
+ /* Nonuniform sectors (top boot) with two x8 devices. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .nb_blocs = { 127, 1, 2, 1 },
+ .sector_len = { 0x10000, 0x08000, 0x02000, 0x04000 },
+ },
+ /* Nonuniform sectors (bottom boot). */
+ {
+ .bank_width = 2,
+ .nb_blocs = { 1, 2, 1, 127 },
+ .sector_len = { 0x04000, 0x02000, 0x08000, 0x10000 },
+ },
+ /* Nonuniform sectors (bottom boot) with two x8 devices. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .nb_blocs = { 1, 2, 1, 127 },
+ .sector_len = { 0x04000, 0x02000, 0x08000, 0x10000 },
+ },
};
int main(int argc, char **argv)
@@ -438,7 +529,7 @@ int main(int argc, char **argv)
if (fd == -1) {
err(1, "Failed to create temporary file %s", image_path);
}
- if (ftruncate(fd, 8 * 1024 * 1024) < 0) {
+ if (ftruncate(fd, UNIFORM_FLASH_SIZE) < 0) {
int error_code = errno;
close(fd);
unlink(image_path);
@@ -454,11 +545,21 @@ int main(int argc, char **argv)
size_t nb_configurations = sizeof configuration / sizeof configuration[0];
for (size_t i = 0; i < nb_configurations; ++i) {
const FlashConfig *config = &configuration[i];
- char *path = g_strdup_printf("pflash-cfi02/%d-%d-%d",
+ char *path = g_strdup_printf("pflash-cfi02"
+ "/geometry/%dx%x-%dx%x-%dx%x-%dx%x"
+ "/%d-%d-%d",
+ config->nb_blocs[0],
+ config->sector_len[0],
+ config->nb_blocs[1],
+ config->sector_len[1],
+ config->nb_blocs[2],
+ config->sector_len[2],
+ config->nb_blocs[3],
+ config->sector_len[3],
config->bank_width,
config->device_width,
config->max_device_width);
- qtest_add_data_func(path, config, test_flash);
+ qtest_add_data_func(path, config, test_geometry);
g_free(path);
}
int result = g_test_run();
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 05/10] block/pflash_cfi02: Implement nonuniform sector sizes
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 05/10] block/pflash_cfi02: Implement nonuniform sector sizes Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
0 siblings, 0 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Laurent Vivier, Thomas Huth, Stephen Checkoway,
qemu-block, Max Reitz, Paolo Bonzini
Some flash chips support sectors of different sizes. For example, the
AMD AM29LV160DT has 31 64 kB sectors, one 32 kB sector, two 8 kB
sectors, and a 16 kB sector, in that order. The AM29LV160DB has those in
the reverse order.
The `num-blocks` and `sector-length` properties work exactly as they did
before: a flash device with uniform sector lengths. To get non-uniform
sector lengths for up to four regions, the following properties may be
set
- region 0. `num-blocks0` and `sector-length0`;
- region 1. `num-blocks1` and `sector-length1`;
- region 2. `num-blocks2` and `sector-length2`; and
- region 3. `num-blocks3` and `sector-length3`.
If the uniform and nonuniform properties are set, then both must specify
a flash device with the same total size. It would be better to disallow
both being set, or make `num-blocks0` and `sector-length0` alias
`num-blocks` and `sector-length`, but that would make testing currently
impossible.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 177 ++++++++++++++++++++++++++-----------
tests/pflash-cfi02-test.c | 179 +++++++++++++++++++++++++++++---------
2 files changed, 265 insertions(+), 91 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index 101628b4ec..c4efbe8cdf 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -28,7 +28,6 @@
* - unlock bypass command
* - CFI queries
*
- * It does not implement boot blocs with reduced size
* It does not implement software data protection as found in many real chips
* It does not implement erase suspend/resume commands
* It does not implement multiple sectors erase
@@ -55,6 +54,13 @@ do { \
#define PFLASH_LAZY_ROMD_THRESHOLD 42
+/*
+ * The size of the cfi_table indirectly depends on this and the start of the
+ * PRI table directly depends on it. 4 is the maximum size (and also what
+ * seems common) without changing the PRT table address.
+ */
+#define PFLASH_MAX_ERASE_REGIONS 4
+
/* Special write cycle for CFI queries. */
#define WCYCLE_CFI 7
@@ -64,8 +70,10 @@ struct PFlashCFI02 {
/*< public >*/
BlockBackend *blk;
- uint32_t sector_len;
- uint32_t nb_blocs;
+ uint32_t uniform_nb_blocs;
+ uint32_t uniform_sector_len;
+ uint32_t nb_blocs[PFLASH_MAX_ERASE_REGIONS];
+ uint32_t sector_len[PFLASH_MAX_ERASE_REGIONS];
uint64_t total_len;
uint64_t interleave_multiplier;
uint8_t mappings;
@@ -86,7 +94,7 @@ struct PFlashCFI02 {
uint16_t ident3;
uint16_t unlock_addr0;
uint16_t unlock_addr1;
- uint8_t cfi_table[0x52];
+ uint8_t cfi_table[0x4D];
QEMUTimer timer;
/* The device replicates the flash memory across its memory space. Emulate
* that by having a container (.mem) filled with an array of aliases
@@ -189,6 +197,25 @@ static uint64_t pflash_data_read(PFlashCFI02 *pfl, hwaddr offset,
return ret;
}
+/*
+ * offset should be a byte offset of the QEMU device and _not_ a device
+ * offset.
+ */
+static uint32_t pflash_sector_len(PFlashCFI02 *pfl, hwaddr offset)
+{
+ assert(offset < pfl->total_len);
+ int nb_regions = pfl->cfi_table[0x2C];
+ hwaddr addr = 0;
+ for (int i = 0; i < nb_regions; ++i) {
+ uint64_t region_size = (uint64_t)pfl->nb_blocs[i] * pfl->sector_len[i];
+ if (addr <= offset && offset < addr + region_size) {
+ return pfl->sector_len[i];
+ }
+ addr += region_size;
+ }
+ abort();
+}
+
static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
{
PFlashCFI02 *pfl = opaque;
@@ -285,6 +312,7 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
PFlashCFI02 *pfl = opaque;
uint8_t *p;
uint8_t cmd;
+ uint32_t sector_len;
cmd = value;
if (pfl->cmd != 0xA0) {
@@ -446,12 +474,14 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
case 0x30:
/* Sector erase */
p = pfl->storage;
- offset &= ~(pfl->sector_len - 1);
- DPRINTF("%s: start sector erase at " TARGET_FMT_plx "\n", __func__,
- offset);
+ sector_len = pflash_sector_len(pfl, offset);
+ offset &= ~(sector_len - 1);
+ DPRINTF("%s: start sector erase at %0*" PRIx64 "-%0*" PRIx64 "\n",
+ __func__, pfl->bank_width * 2, offset,
+ pfl->bank_width * 2, offset + sector_len - 1);
if (!pfl->ro) {
- memset(p + offset, 0xFF, pfl->sector_len);
- pflash_update(pfl, offset, pfl->sector_len);
+ memset(p + offset, 0xFF, sector_len);
+ pflash_update(pfl, offset, sector_len);
}
set_dq7(pfl, 0x00);
/* Let's wait 1/2 second before sector erase is done */
@@ -515,15 +545,14 @@ static const MemoryRegionOps pflash_cfi02_ops = {
static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
{
PFlashCFI02 *pfl = PFLASH_CFI02(dev);
- uint32_t chip_len;
int ret;
Error *local_err = NULL;
- if (pfl->sector_len == 0) {
+ if (pfl->uniform_sector_len == 0 && pfl->sector_len[0] == 0) {
error_setg(errp, "attribute \"sector-length\" not specified or zero.");
return;
}
- if (pfl->nb_blocs == 0) {
+ if (pfl->uniform_nb_blocs == 0 && pfl->nb_blocs[0] == 0) {
error_setg(errp, "attribute \"num-blocks\" not specified or zero.");
return;
}
@@ -619,7 +648,53 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
return;
}
- pfl->total_len = pfl->sector_len * pfl->nb_blocs;
+ int num_devices = pfl->bank_width / pfl->device_width;
+ int nb_regions;
+ pfl->total_len = 0;
+ for (nb_regions = 0; nb_regions < PFLASH_MAX_ERASE_REGIONS; ++nb_regions) {
+ if (pfl->nb_blocs[nb_regions] == 0) {
+ break;
+ }
+ uint64_t sector_len_per_device = pfl->sector_len[nb_regions] /
+ num_devices;
+
+ /*
+ * The size of each flash sector must be a power of 2 and it must be
+ * aligned at the same power of 2.
+ */
+ if (sector_len_per_device & 0xff ||
+ sector_len_per_device >= (1 << 24) ||
+ !is_power_of_2(sector_len_per_device))
+ {
+ error_setg(errp, "unsupported configuration: "
+ "sector length[%d] per device = %" PRIx64 ".",
+ nb_regions, sector_len_per_device);
+ return;
+ }
+ if ((pfl->total_len / num_devices) & (sector_len_per_device - 1)) {
+ error_setg(errp, "unsupported configuration: "
+ "flash region %d not correctly aligned.",
+ nb_regions);
+ return;
+ }
+
+ pfl->total_len += (uint64_t)pfl->sector_len[nb_regions] *
+ pfl->nb_blocs[nb_regions];
+ }
+
+ uint64_t uniform_len = (uint64_t)pfl->uniform_nb_blocs *
+ pfl->uniform_sector_len;
+ if (nb_regions == 0) {
+ nb_regions = 1;
+ pfl->nb_blocs[0] = pfl->uniform_nb_blocs;
+ pfl->sector_len[0] = pfl->uniform_sector_len;
+ pfl->total_len = uniform_len;
+ } else if (uniform_len != 0 && uniform_len != pfl->total_len) {
+ error_setg(errp, "\"num-blocks\"*\"sector-length\" "
+ "different from \"num-blocks0\"*\'sector-length0\" + ... + "
+ "\"num-blocks3\"*\"sector-length3\"");
+ return;
+ }
/*
* If the flash is not a power of 2, then the code for handling multiple
@@ -631,18 +706,6 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
return;
}
- int num_devices = pfl->bank_width / pfl->device_width;
- uint64_t sector_len_per_device = pfl->sector_len / num_devices;
- uint64_t device_len = sector_len_per_device * pfl->nb_blocs;
-
- if (sector_len_per_device & 0xff || sector_len_per_device >= (1 << 24)) {
- error_setg(errp,
- "unsupported configuration: sector length per device = "
- "%" PRIx64 ".",
- sector_len_per_device);
- return;
- }
-
memory_region_init_rom_device(&pfl->orig_mem, OBJECT(pfl),
&pflash_cfi02_ops, pfl, pfl->name,
pfl->total_len, &local_err);
@@ -650,8 +713,6 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->unlock_addr0 &= 0x7FF;
pfl->unlock_addr1 &= 0x7FF;
- chip_len = pfl->sector_len * pfl->nb_blocs;
-
if (local_err) {
error_propagate(errp, local_err);
return;
@@ -672,8 +733,8 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
}
if (pfl->blk) {
- if (!blk_check_size_and_read_all(pfl->blk, pfl->storage, chip_len,
- errp)) {
+ if (!blk_check_size_and_read_all(pfl->blk, pfl->storage,
+ pfl->total_len, errp)) {
vmstate_unregister_ram(&pfl->orig_mem, DEVICE(pfl));
return;
}
@@ -697,7 +758,7 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->cfi_table[0x13] = 0x02;
pfl->cfi_table[0x14] = 0x00;
/* Primary extended table address */
- pfl->cfi_table[0x15] = 0x31;
+ pfl->cfi_table[0x15] = 0x40;
pfl->cfi_table[0x16] = 0x00;
/* Alternate command set (none) */
pfl->cfi_table[0x17] = 0x00;
@@ -730,7 +791,7 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
/* Max timeout for chip erase */
pfl->cfi_table[0x26] = 0x0D;
/* Device size */
- pfl->cfi_table[0x27] = ctz32(device_len);
+ pfl->cfi_table[0x27] = ctz32(pfl->total_len / num_devices);
/* Flash device interface */
pfl->cfi_table[0x28] = device_interface_code;
pfl->cfi_table[0x29] = device_interface_code >> 8;
@@ -739,37 +800,49 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
/* pfl->cfi_table[0x2A] = 0x05; */
pfl->cfi_table[0x2A] = 0x00;
pfl->cfi_table[0x2B] = 0x00;
- /* Number of erase block regions (uniform) */
- pfl->cfi_table[0x2C] = 0x01;
- /* Erase block region 1 */
- pfl->cfi_table[0x2D] = pfl->nb_blocs - 1;
- pfl->cfi_table[0x2E] = (pfl->nb_blocs - 1) >> 8;
- pfl->cfi_table[0x2F] = sector_len_per_device >> 8;
- pfl->cfi_table[0x30] = sector_len_per_device >> 16;
+ /* Number of erase block regions */
+ pfl->cfi_table[0x2C] = nb_regions;
+ /* Erase block regions */
+ for (int i = 0; i < nb_regions; ++i) {
+ uint32_t sector_len_per_device = pfl->sector_len[i] / num_devices;
+ pfl->cfi_table[0x2D + 4 * i] = pfl->nb_blocs[i] - 1;
+ pfl->cfi_table[0x2E + 4 * i] = (pfl->nb_blocs[i] - 1) >> 8;
+ pfl->cfi_table[0x2F + 4 * i] = sector_len_per_device >> 8;
+ pfl->cfi_table[0x30 + 4 * i] = sector_len_per_device >> 16;
+ }
/* Extended */
- pfl->cfi_table[0x31] = 'P';
- pfl->cfi_table[0x32] = 'R';
- pfl->cfi_table[0x33] = 'I';
+ pfl->cfi_table[0x40] = 'P';
+ pfl->cfi_table[0x41] = 'R';
+ pfl->cfi_table[0x42] = 'I';
- pfl->cfi_table[0x34] = '1';
- pfl->cfi_table[0x35] = '0';
+ pfl->cfi_table[0x43] = '1'; /* version 1.0 */
+ pfl->cfi_table[0x44] = '0';
- pfl->cfi_table[0x36] = 0x00;
- pfl->cfi_table[0x37] = 0x00;
- pfl->cfi_table[0x38] = 0x00;
- pfl->cfi_table[0x39] = 0x00;
+ pfl->cfi_table[0x45] = 0x00; /* Address sensitive unlock required. */
+ pfl->cfi_table[0x46] = 0x00; /* Erase suspend not supported. */
+ pfl->cfi_table[0x47] = 0x00; /* Sector protect not supported. */
+ pfl->cfi_table[0x48] = 0x00; /* Temporary sector unprotect not supported. */
- pfl->cfi_table[0x3a] = 0x00;
+ pfl->cfi_table[0x49] = 0x00; /* Sector protect/unprotect scheme. */
- pfl->cfi_table[0x3b] = 0x00;
- pfl->cfi_table[0x3c] = 0x00;
+ pfl->cfi_table[0x4a] = 0x00; /* Simultaneous operation not supported. */
+ pfl->cfi_table[0x4b] = 0x00; /* Burst mode not supported. */
+ pfl->cfi_table[0x4c] = 0x00; /* Page mode not supported. */
}
static Property pflash_cfi02_properties[] = {
DEFINE_PROP_DRIVE("drive", PFlashCFI02, blk),
- DEFINE_PROP_UINT32("num-blocks", PFlashCFI02, nb_blocs, 0),
- DEFINE_PROP_UINT32("sector-length", PFlashCFI02, sector_len, 0),
+ DEFINE_PROP_UINT32("num-blocks", PFlashCFI02, uniform_nb_blocs, 0),
+ DEFINE_PROP_UINT32("sector-length", PFlashCFI02, uniform_sector_len, 0),
+ DEFINE_PROP_UINT32("num-blocks0", PFlashCFI02, nb_blocs[0], 0),
+ DEFINE_PROP_UINT32("sector-length0", PFlashCFI02, sector_len[0], 0),
+ DEFINE_PROP_UINT32("num-blocks1", PFlashCFI02, nb_blocs[1], 0),
+ DEFINE_PROP_UINT32("sector-length1", PFlashCFI02, sector_len[1], 0),
+ DEFINE_PROP_UINT32("num-blocks2", PFlashCFI02, nb_blocs[2], 0),
+ DEFINE_PROP_UINT32("sector-length2", PFlashCFI02, sector_len[2], 0),
+ DEFINE_PROP_UINT32("num-blocks3", PFlashCFI02, nb_blocs[3], 0),
+ DEFINE_PROP_UINT32("sector-length3", PFlashCFI02, sector_len[3], 0),
DEFINE_PROP_UINT8("width", PFlashCFI02, bank_width, 0),
DEFINE_PROP_UINT8("device-width", PFlashCFI02, device_width, 0),
DEFINE_PROP_UINT8("max-device-width", PFlashCFI02, max_device_width, 0),
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index 4d621e584d..dc85783a6a 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -21,6 +21,9 @@
#define MP_FLASH_SIZE_MAX (32 * 1024 * 1024)
#define BASE_ADDR (0x100000000ULL - MP_FLASH_SIZE_MAX)
+#define UNIFORM_FLASH_SIZE (8 * 1024 * 1024)
+#define UNIFORM_FLASH_SECTOR_SIZE (64 * 1024)
+
/* Use a newtype to keep flash addresses separate from byte addresses. */
typedef struct {
uint64_t addr;
@@ -43,9 +46,14 @@ typedef struct {
#define UNLOCK_BYPASS_RESET_CMD 0x00
typedef struct {
+ /* Interleave configuration. */
int bank_width;
int device_width;
int max_device_width;
+
+ /* Nonuniform block size. */
+ int nb_blocs[4];
+ int sector_len[4];
} FlashConfig;
static char image_path[] = "/tmp/qtest.XXXXXX";
@@ -60,12 +68,22 @@ static FlashConfig expand_config_defaults(const FlashConfig *c)
{
FlashConfig ret = *c;
+ if (ret.bank_width == 0) {
+ ret.bank_width = 2;
+ }
if (ret.device_width == 0) {
ret.device_width = ret.bank_width;
}
if (ret.max_device_width == 0) {
ret.max_device_width = ret.device_width;
}
+ if (ret.nb_blocs[0] == 0 && ret.sector_len[0] == 0) {
+ ret.sector_len[0] = UNIFORM_FLASH_SECTOR_SIZE;
+ ret.nb_blocs[0] = UNIFORM_FLASH_SIZE / UNIFORM_FLASH_SECTOR_SIZE;
+ }
+
+ /* XXX: Limitations of test harness. */
+ assert(ret.bank_width == 2);
return ret;
}
@@ -157,8 +175,8 @@ static inline uint64_t as_byte_addr(const FlashConfig *c, faddr flash_addr)
* which is bank_width / device_width, and multiply that by the maximum
* device width.
*/
- int num_devices = c->bank_width / c->device_width;
- return flash_addr.addr * (num_devices * c->max_device_width);
+ int nb_devices = c->bank_width / c->device_width;
+ return flash_addr.addr * (nb_devices * c->max_device_width);
}
/*
@@ -248,22 +266,53 @@ static void chip_erase(const FlashConfig *c)
flash_cmd(c, UNLOCK0_ADDR, CHIP_ERASE_CMD);
}
-static void test_flash(const void *opaque)
+/*
+ * Test flash commands with a variety of device geometry.
+ */
+static void test_geometry(const void *opaque)
{
const FlashConfig *config = opaque;
+ /* Set the properties that are under our control. */
global_qtest = qtest_initf("-M musicpal,accel=qtest"
" -drive if=pflash,file=%s,format=raw,"
"copy-on-read"
+ /* Interleave properties. */
" -global driver=cfi.pflash02,"
"property=device-width,value=%d"
" -global driver=cfi.pflash02,"
- "property=max-device-width,value=%d",
+ "property=max-device-width,value=%d"
+ /* Device geometry properties. */
+ " -global driver=cfi.pflash02,"
+ "property=num-blocks0,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=sector-length0,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=num-blocks1,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=sector-length1,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=num-blocks2,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=sector-length2,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=num-blocks3,value=%d"
+ " -global driver=cfi.pflash02,"
+ "property=sector-length3,value=%d",
image_path,
config->device_width,
- config->max_device_width);
+ config->max_device_width,
+ config->nb_blocs[0],
+ config->sector_len[0],
+ config->nb_blocs[1],
+ config->sector_len[1],
+ config->nb_blocs[2],
+ config->sector_len[2],
+ config->nb_blocs[3],
+ config->sector_len[3]);
const FlashConfig explicit_config = expand_config_defaults(config);
const FlashConfig *c = &explicit_config;
+ int nb_devices = c->bank_width / c->device_width;
/* Check the IDs. */
unlock(c);
@@ -287,38 +336,52 @@ static void test_flash(const void *opaque)
g_assert_cmpint(flash_query(c, FLASH_ADDR(0x11)), ==, replicate(c, 'R'));
g_assert_cmpint(flash_query(c, FLASH_ADDR(0x12)), ==, replicate(c, 'Y'));
/* Num erase regions. */
- g_assert_cmpint(flash_query_1(c, FLASH_ADDR(0x2C)), >=, 1);
- uint32_t nb_sectors = flash_query_1(c, FLASH_ADDR(0x2D)) +
- (flash_query_1(c, FLASH_ADDR(0x2E)) << 8) + 1;
- uint32_t sector_len = (flash_query_1(c, FLASH_ADDR(0x2F)) << 8) +
- (flash_query_1(c, FLASH_ADDR(0x30)) << 16);
+ int nb_erase_regions = flash_query_1(c, FLASH_ADDR(0x2C));
+ g_assert_cmpint(nb_erase_regions, ==,
+ !!c->nb_blocs[0] + !!c->nb_blocs[1] + !!c->nb_blocs[2] +
+ !!c->nb_blocs[3]);
reset(c);
-
const uint64_t dq7 = replicate(c, 0x80);
const uint64_t dq6 = replicate(c, 0x40);
- /* Erase and program sector. */
- for (uint32_t i = 0; i < nb_sectors; ++i) {
- uint64_t byte_addr = i * sector_len;
- sector_erase(c, byte_addr);
- /* Read toggle. */
- uint64_t status0 = flash_read(c, byte_addr);
- /* DQ7 is 0 during an erase. */
- g_assert_cmpint(status0 & dq7, ==, 0);
- uint64_t status1 = flash_read(c, byte_addr);
- /* DQ6 toggles during an erase. */
- g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
- /* Wait for erase to complete. */
- clock_step_next();
- /* Ensure DQ6 has stopped toggling. */
- g_assert_cmpint(flash_read(c, byte_addr), ==, flash_read(c, byte_addr));
- /* Now the data should be valid. */
- g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
- /* Program a bit pattern. */
- program(c, byte_addr, 0x55);
- g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x55);
- program(c, byte_addr, 0xA5);
- g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x05);
+ uint64_t byte_addr = 0;
+ for (int region = 0; region < nb_erase_regions; ++region) {
+ uint64_t base = 0x2D + 4 * region;
+ flash_cmd(c, CFI_ADDR, CFI_CMD);
+ uint32_t nb_sectors = flash_query_1(c, FLASH_ADDR(base + 0)) +
+ (flash_query_1(c, FLASH_ADDR(base + 1)) << 8) + 1;
+ uint32_t sector_len = (flash_query_1(c, FLASH_ADDR(base + 2)) << 8) +
+ (flash_query_1(c, FLASH_ADDR(base + 3)) << 16);
+ sector_len *= nb_devices;
+ g_assert_cmpint(nb_sectors, ==, c->nb_blocs[region]);
+ g_assert_cmpint(sector_len, ==, c->sector_len[region]);
+ reset(c);
+
+ /* Erase and program sector. */
+ for (uint32_t i = 0; i < nb_sectors; ++i) {
+ sector_erase(c, byte_addr);
+ /* Read toggle. */
+ uint64_t status0 = flash_read(c, byte_addr);
+ /* DQ7 is 0 during an erase. */
+ g_assert_cmpint(status0 & dq7, ==, 0);
+ uint64_t status1 = flash_read(c, byte_addr);
+ /* DQ6 toggles during an erase. */
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ /* Wait for erase to complete. */
+ clock_step_next();
+ /* Ensure DQ6 has stopped toggling. */
+ g_assert_cmpint(flash_read(c, byte_addr), ==,
+ flash_read(c, byte_addr));
+ /* Now the data should be valid. */
+ g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
+
+ /* Program a bit pattern. */
+ program(c, byte_addr, 0x55);
+ g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x55);
+ program(c, byte_addr, 0xA5);
+ g_assert_cmpint(flash_read(c, byte_addr) & 0xFF, ==, 0x05);
+ byte_addr += sector_len;
+ }
}
/* Erase the chip. */
@@ -336,9 +399,11 @@ static void test_flash(const void *opaque)
g_assert_cmpint(flash_read(c, 0), ==, flash_read(c, 0));
/* Now the data should be valid. */
- for (uint32_t i = 0; i < nb_sectors; ++i) {
- uint64_t byte_addr = i * sector_len;
- g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
+ for (int region = 0; region < nb_erase_regions; ++region) {
+ for (uint32_t i = 0; i < c->nb_blocs[region]; ++i) {
+ uint64_t byte_addr = i * c->sector_len[region];
+ g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
+ }
}
/* Unlock bypass */
@@ -430,6 +495,32 @@ static const FlashConfig configuration[] = {
.device_width = 1,
.max_device_width = 4,
},
+ /* Nonuniform sectors (top boot). */
+ {
+ .bank_width = 2,
+ .nb_blocs = { 127, 1, 2, 1 },
+ .sector_len = { 0x10000, 0x08000, 0x02000, 0x04000 },
+ },
+ /* Nonuniform sectors (top boot) with two x8 devices. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .nb_blocs = { 127, 1, 2, 1 },
+ .sector_len = { 0x10000, 0x08000, 0x02000, 0x04000 },
+ },
+ /* Nonuniform sectors (bottom boot). */
+ {
+ .bank_width = 2,
+ .nb_blocs = { 1, 2, 1, 127 },
+ .sector_len = { 0x04000, 0x02000, 0x08000, 0x10000 },
+ },
+ /* Nonuniform sectors (bottom boot) with two x8 devices. */
+ {
+ .bank_width = 2,
+ .device_width = 1,
+ .nb_blocs = { 1, 2, 1, 127 },
+ .sector_len = { 0x04000, 0x02000, 0x08000, 0x10000 },
+ },
};
int main(int argc, char **argv)
@@ -438,7 +529,7 @@ int main(int argc, char **argv)
if (fd == -1) {
err(1, "Failed to create temporary file %s", image_path);
}
- if (ftruncate(fd, 8 * 1024 * 1024) < 0) {
+ if (ftruncate(fd, UNIFORM_FLASH_SIZE) < 0) {
int error_code = errno;
close(fd);
unlink(image_path);
@@ -454,11 +545,21 @@ int main(int argc, char **argv)
size_t nb_configurations = sizeof configuration / sizeof configuration[0];
for (size_t i = 0; i < nb_configurations; ++i) {
const FlashConfig *config = &configuration[i];
- char *path = g_strdup_printf("pflash-cfi02/%d-%d-%d",
+ char *path = g_strdup_printf("pflash-cfi02"
+ "/geometry/%dx%x-%dx%x-%dx%x-%dx%x"
+ "/%d-%d-%d",
+ config->nb_blocs[0],
+ config->sector_len[0],
+ config->nb_blocs[1],
+ config->sector_len[1],
+ config->nb_blocs[2],
+ config->sector_len[2],
+ config->nb_blocs[3],
+ config->sector_len[3],
config->bank_width,
config->device_width,
config->max_device_width);
- qtest_add_data_func(path, config, test_flash);
+ qtest_add_data_func(path, config, test_geometry);
g_free(path);
}
int result = g_test_run();
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 06/10] block/pflash_cfi02: Fix CFI in autoselect mode
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
` (5 preceding siblings ...)
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 05/10] block/pflash_cfi02: Implement nonuniform sector sizes Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 07/10] block/pflash_cfi02: Fix reset command not ignored during erase Stephen Checkoway
` (3 subsequent siblings)
10 siblings, 1 reply; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Max Reitz, qemu-block, Stephen Checkoway, Thomas Huth,
Laurent Vivier, Paolo Bonzini
After a flash device enters CFI mode from autoselect mode, the reset
command returns the device to autoselect mode. An additional reset
command is necessary to return to read array mode.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 21 +++++++++++++++++----
tests/pflash-cfi02-test.c | 36 ++++++++++++++++++++++++++++++++++++
2 files changed, 53 insertions(+), 4 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index c4efbe8cdf..be10036886 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -61,8 +61,9 @@ do { \
*/
#define PFLASH_MAX_ERASE_REGIONS 4
-/* Special write cycle for CFI queries. */
+/* Special write cycles for CFI queries. */
#define WCYCLE_CFI 7
+#define WCYCLE_AUTOSELECT_CFI 8
struct PFlashCFI02 {
/*< private >*/
@@ -325,6 +326,12 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
}
if (cmd == 0xF0) {
+ if (pfl->wcycle == WCYCLE_AUTOSELECT_CFI) {
+ /* Return to autoselect mode. */
+ pfl->wcycle = 3;
+ pfl->cmd = 0x90;
+ return;
+ }
goto reset_flash;
}
}
@@ -350,7 +357,6 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* We're in read mode */
check_unlock0:
if (masked_addr == 0x55 && cmd == 0x98) {
- enter_CFI_mode:
/* Enter CFI query mode */
pfl->wcycle = WCYCLE_CFI;
pfl->cmd = 0x98;
@@ -427,9 +433,15 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* Unlock bypass reset */
goto reset_flash;
}
- /* We can enter CFI query mode from autoselect mode */
+ /*
+ * We can enter CFI query mode from autoselect mode, but we must
+ * return to autoselect mode after a reset.
+ */
if (masked_addr == 0x55 && cmd == 0x98) {
- goto enter_CFI_mode;
+ /* Enter autoselect CFI query mode */
+ pfl->wcycle = WCYCLE_AUTOSELECT_CFI;
+ pfl->cmd = 0x98;
+ return;
}
/* No break here */
default:
@@ -510,6 +522,7 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
}
break;
case WCYCLE_CFI: /* Special value for CFI queries */
+ case WCYCLE_AUTOSELECT_CFI:
DPRINTF("%s: invalid write in CFI query mode\n", __func__);
goto reset_flash;
default:
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index dc85783a6a..ae1cd4e54b 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -437,6 +437,39 @@ static void test_geometry(const void *opaque)
qtest_quit(global_qtest);
}
+/*
+ * Test that
+ * 1. enter autoselect mode;
+ * 2. enter CFI mode; and then
+ * 3. exit CFI mode
+ * leaves the flash device in autoselect mode.
+ */
+static void test_cfi_in_autoselect(const void *opaque)
+{
+ const FlashConfig *c = opaque;
+ global_qtest = qtest_initf("-M musicpal,accel=qtest"
+ " -drive if=pflash,file=%s,format=raw,"
+ "copy-on-read",
+ image_path);
+
+ /* 1. Enter autoselect. */
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, AUTOSELECT_CMD);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
+
+ /* 2. Enter CFI. */
+ flash_cmd(c, CFI_ADDR, CFI_CMD);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x10)), ==, replicate(c, 'Q'));
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x11)), ==, replicate(c, 'R'));
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x12)), ==, replicate(c, 'Y'));
+
+ /* 3. Exit CFI. */
+ reset(c);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
+
+ qtest_quit(global_qtest);
+}
+
static void cleanup(void *opaque)
{
unlink(image_path);
@@ -562,6 +595,9 @@ int main(int argc, char **argv)
qtest_add_data_func(path, config, test_geometry);
g_free(path);
}
+
+ qtest_add_data_func("pflash-cfi02/cfi-in-autoselect", &configuration[0],
+ test_cfi_in_autoselect);
int result = g_test_run();
cleanup(NULL);
return result;
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 06/10] block/pflash_cfi02: Fix CFI in autoselect mode
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 06/10] block/pflash_cfi02: Fix CFI in autoselect mode Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
0 siblings, 0 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Laurent Vivier, Thomas Huth, Stephen Checkoway,
qemu-block, Max Reitz, Paolo Bonzini
After a flash device enters CFI mode from autoselect mode, the reset
command returns the device to autoselect mode. An additional reset
command is necessary to return to read array mode.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 21 +++++++++++++++++----
tests/pflash-cfi02-test.c | 36 ++++++++++++++++++++++++++++++++++++
2 files changed, 53 insertions(+), 4 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index c4efbe8cdf..be10036886 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -61,8 +61,9 @@ do { \
*/
#define PFLASH_MAX_ERASE_REGIONS 4
-/* Special write cycle for CFI queries. */
+/* Special write cycles for CFI queries. */
#define WCYCLE_CFI 7
+#define WCYCLE_AUTOSELECT_CFI 8
struct PFlashCFI02 {
/*< private >*/
@@ -325,6 +326,12 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
}
if (cmd == 0xF0) {
+ if (pfl->wcycle == WCYCLE_AUTOSELECT_CFI) {
+ /* Return to autoselect mode. */
+ pfl->wcycle = 3;
+ pfl->cmd = 0x90;
+ return;
+ }
goto reset_flash;
}
}
@@ -350,7 +357,6 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* We're in read mode */
check_unlock0:
if (masked_addr == 0x55 && cmd == 0x98) {
- enter_CFI_mode:
/* Enter CFI query mode */
pfl->wcycle = WCYCLE_CFI;
pfl->cmd = 0x98;
@@ -427,9 +433,15 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* Unlock bypass reset */
goto reset_flash;
}
- /* We can enter CFI query mode from autoselect mode */
+ /*
+ * We can enter CFI query mode from autoselect mode, but we must
+ * return to autoselect mode after a reset.
+ */
if (masked_addr == 0x55 && cmd == 0x98) {
- goto enter_CFI_mode;
+ /* Enter autoselect CFI query mode */
+ pfl->wcycle = WCYCLE_AUTOSELECT_CFI;
+ pfl->cmd = 0x98;
+ return;
}
/* No break here */
default:
@@ -510,6 +522,7 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
}
break;
case WCYCLE_CFI: /* Special value for CFI queries */
+ case WCYCLE_AUTOSELECT_CFI:
DPRINTF("%s: invalid write in CFI query mode\n", __func__);
goto reset_flash;
default:
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index dc85783a6a..ae1cd4e54b 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -437,6 +437,39 @@ static void test_geometry(const void *opaque)
qtest_quit(global_qtest);
}
+/*
+ * Test that
+ * 1. enter autoselect mode;
+ * 2. enter CFI mode; and then
+ * 3. exit CFI mode
+ * leaves the flash device in autoselect mode.
+ */
+static void test_cfi_in_autoselect(const void *opaque)
+{
+ const FlashConfig *c = opaque;
+ global_qtest = qtest_initf("-M musicpal,accel=qtest"
+ " -drive if=pflash,file=%s,format=raw,"
+ "copy-on-read",
+ image_path);
+
+ /* 1. Enter autoselect. */
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, AUTOSELECT_CMD);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
+
+ /* 2. Enter CFI. */
+ flash_cmd(c, CFI_ADDR, CFI_CMD);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x10)), ==, replicate(c, 'Q'));
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x11)), ==, replicate(c, 'R'));
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0x12)), ==, replicate(c, 'Y'));
+
+ /* 3. Exit CFI. */
+ reset(c);
+ g_assert_cmpint(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
+
+ qtest_quit(global_qtest);
+}
+
static void cleanup(void *opaque)
{
unlink(image_path);
@@ -562,6 +595,9 @@ int main(int argc, char **argv)
qtest_add_data_func(path, config, test_geometry);
g_free(path);
}
+
+ qtest_add_data_func("pflash-cfi02/cfi-in-autoselect", &configuration[0],
+ test_cfi_in_autoselect);
int result = g_test_run();
cleanup(NULL);
return result;
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 07/10] block/pflash_cfi02: Fix reset command not ignored during erase
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
` (6 preceding siblings ...)
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 06/10] block/pflash_cfi02: Fix CFI in autoselect mode Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 08/10] block/pflash_cfi02: Implement multi-sector erase Stephen Checkoway
` (2 subsequent siblings)
10 siblings, 1 reply; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel; +Cc: Kevin Wolf, Max Reitz, qemu-block, Stephen Checkoway
When the flash device is performing a chip erase, all commands are
ignored. When it is performing a sector erase, only the erase suspend
command is valid, which is currently not supported.
In particular, the reset command should not cause the device to reset to
read array mode while programming is on going.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index be10036886..cb1160eb35 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -325,7 +325,8 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
pfl->bank_width * 2, value);
}
- if (cmd == 0xF0) {
+ /* Reset does nothing during chip erase and sector erase. */
+ if (cmd == 0xF0 && pfl->cmd != 0x10 && pfl->cmd != 0x30) {
if (pfl->wcycle == WCYCLE_AUTOSELECT_CFI) {
/* Return to autoselect mode. */
pfl->wcycle = 3;
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 07/10] block/pflash_cfi02: Fix reset command not ignored during erase
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 07/10] block/pflash_cfi02: Fix reset command not ignored during erase Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
0 siblings, 0 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel; +Cc: Kevin Wolf, Stephen Checkoway, qemu-block, Max Reitz
When the flash device is performing a chip erase, all commands are
ignored. When it is performing a sector erase, only the erase suspend
command is valid, which is currently not supported.
In particular, the reset command should not cause the device to reset to
read array mode while programming is on going.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index be10036886..cb1160eb35 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -325,7 +325,8 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
pfl->bank_width * 2, value);
}
- if (cmd == 0xF0) {
+ /* Reset does nothing during chip erase and sector erase. */
+ if (cmd == 0xF0 && pfl->cmd != 0x10 && pfl->cmd != 0x30) {
if (pfl->wcycle == WCYCLE_AUTOSELECT_CFI) {
/* Return to autoselect mode. */
pfl->wcycle = 3;
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 08/10] block/pflash_cfi02: Implement multi-sector erase
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
` (7 preceding siblings ...)
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 07/10] block/pflash_cfi02: Fix reset command not ignored during erase Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 09/10] block/pflash_cfi02: Implement erase suspend/resume Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 10/10] block/pflash_cfi02: Use the chip erase time specified in the CFI table Stephen Checkoway
10 siblings, 1 reply; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Max Reitz, qemu-block, Stephen Checkoway, Thomas Huth,
Laurent Vivier, Paolo Bonzini
After two unlock cycles and a sector erase command, the AMD flash chips
start a 50 us erase time out. Any additional sector erase commands add a
sector to be erased and restart the 50 us timeout. During the timeout,
status bit DQ3 is cleared. After the time out, DQ3 is asserted during
erasure.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 94 +++++++++++++++++++++++++++++++--------
tests/pflash-cfi02-test.c | 59 ++++++++++++++++++++++--
2 files changed, 131 insertions(+), 22 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index cb1160eb35..21ceb0823b 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -30,7 +30,6 @@
*
* It does not implement software data protection as found in many real chips
* It does not implement erase suspend/resume commands
- * It does not implement multiple sectors erase
*/
#include "qemu/osdep.h"
@@ -106,6 +105,7 @@ struct PFlashCFI02 {
MemoryRegion orig_mem;
int rom_mode;
int read_counter; /* used for lazy switch-back to rom mode */
+ int sectors_to_erase;
char *name;
void *storage;
};
@@ -136,6 +136,22 @@ static inline void toggle_dq6(PFlashCFI02 *pfl)
pfl->status ^= pfl->interleave_multiplier * 0x40;
}
+/*
+ * Turn on DQ3.
+ */
+static inline void assert_dq3(PFlashCFI02 *pfl)
+{
+ pfl->status |= pfl->interleave_multiplier * 0x08;
+}
+
+/*
+ * Turn off DQ3.
+ */
+static inline void reset_dq3(PFlashCFI02 *pfl)
+{
+ pfl->status &= ~(pfl->interleave_multiplier * 0x08);
+}
+
/*
* Set up replicated mappings of the same region.
*/
@@ -159,11 +175,37 @@ static void pflash_register_memory(PFlashCFI02 *pfl, int rom_mode)
pfl->rom_mode = rom_mode;
}
-static void pflash_timer (void *opaque)
+static void pflash_timer(void *opaque)
{
PFlashCFI02 *pfl = opaque;
trace_pflash_timer_expired(pfl->cmd);
+ if (pfl->cmd == 0x30) {
+ /*
+ * Sector erase. If DQ3 is 0 when the timer expires, then the 50
+ * us erase timeout has expired so we need to start the timer for the
+ * sector erase algorithm. Otherwise, the erase completed and we should
+ * go back to read array mode.
+ */
+ if ((pfl->status & 0x08) == 0) {
+ assert_dq3(pfl);
+ /*
+ * CFI address 0x21 is "Typical timeout per individual block erase
+ * 2^N ms"
+ */
+ uint64_t timeout = ((1ULL << pfl->cfi_table[0x21]) *
+ pfl->sectors_to_erase) * 1000000;
+ timer_mod(&pfl->timer,
+ qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + timeout);
+ DPRINTF("%s: erase timeout fired; erasing %d sectors\n",
+ __func__, pfl->sectors_to_erase);
+ return;
+ }
+ DPRINTF("%s: sector erase complete\n", __func__);
+ pfl->sectors_to_erase = 0;
+ reset_dq3(pfl);
+ }
+
/* Reset flash */
toggle_dq7(pfl);
if (pfl->bypass) {
@@ -307,13 +349,30 @@ static void pflash_update(PFlashCFI02 *pfl, int offset, int size)
}
}
+static void pflash_sector_erase(PFlashCFI02 *pfl, hwaddr offset)
+{
+ uint64_t sector_len = pflash_sector_len(pfl, offset);
+ offset &= ~(sector_len - 1);
+ DPRINTF("%s: start sector erase at %0*" PRIx64 "-%0*" PRIx64 "\n",
+ __func__, pfl->bank_width * 2, offset,
+ pfl->bank_width * 2, offset + sector_len - 1);
+ if (!pfl->ro) {
+ uint8_t *p = pfl->storage;
+ memset(p + offset, 0xFF, sector_len);
+ pflash_update(pfl, offset, sector_len);
+ }
+ set_dq7(pfl, 0x00);
+ ++pfl->sectors_to_erase;
+ /* Set (or reset) the 50 us timer for additional erase commands. */
+ timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + 50000);
+}
+
static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
unsigned int width)
{
PFlashCFI02 *pfl = opaque;
uint8_t *p;
uint8_t cmd;
- uint32_t sector_len;
cmd = value;
if (pfl->cmd != 0xA0) {
@@ -486,20 +545,7 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
break;
case 0x30:
/* Sector erase */
- p = pfl->storage;
- sector_len = pflash_sector_len(pfl, offset);
- offset &= ~(sector_len - 1);
- DPRINTF("%s: start sector erase at %0*" PRIx64 "-%0*" PRIx64 "\n",
- __func__, pfl->bank_width * 2, offset,
- pfl->bank_width * 2, offset + sector_len - 1);
- if (!pfl->ro) {
- memset(p + offset, 0xFF, sector_len);
- pflash_update(pfl, offset, sector_len);
- }
- set_dq7(pfl, 0x00);
- /* Let's wait 1/2 second before sector erase is done */
- timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) +
- (NANOSECONDS_PER_SECOND / 2));
+ pflash_sector_erase(pfl, offset);
break;
default:
DPRINTF("%s: invalid command %02x (wc 5)\n", __func__, cmd);
@@ -513,7 +559,19 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* Ignore writes during chip erase */
return;
case 0x30:
- /* Ignore writes during sector erase */
+ /*
+ * If DQ3 is 0, additional sector erase commands can be
+ * written and anything else (other than an erase suspend) resets
+ * the device.
+ */
+ if ((pfl->status & 0x08) == 0) {
+ if (cmd == 0x30) {
+ pflash_sector_erase(pfl, offset);
+ } else {
+ goto reset_flash;
+ }
+ }
+ /* Ignore writes during the actual erase. */
return;
default:
/* Should never happen */
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index ae1cd4e54b..1cd9807c1b 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -37,6 +37,7 @@ typedef struct {
#define CFI_CMD 0x98
#define UNLOCK0_CMD 0xAA
#define UNLOCK1_CMD 0x55
+#define SECOND_UNLOCK_CMD 0x80
#define AUTOSELECT_CMD 0x90
#define RESET_CMD 0xF0
#define PROGRAM_CMD 0xA0
@@ -222,7 +223,7 @@ static void reset(const FlashConfig *c)
static void sector_erase(const FlashConfig *c, uint64_t byte_addr)
{
unlock(c);
- flash_cmd(c, UNLOCK0_ADDR, 0x80);
+ flash_cmd(c, UNLOCK0_ADDR, SECOND_UNLOCK_CMD);
unlock(c);
flash_write(c, byte_addr, replicate(c, SECTOR_ERASE_CMD));
}
@@ -261,7 +262,7 @@ static void program(const FlashConfig *c, uint64_t byte_addr, uint16_t data)
static void chip_erase(const FlashConfig *c)
{
unlock(c);
- flash_cmd(c, UNLOCK0_ADDR, 0x80);
+ flash_cmd(c, UNLOCK0_ADDR, SECOND_UNLOCK_CMD);
unlock(c);
flash_cmd(c, UNLOCK0_ADDR, CHIP_ERASE_CMD);
}
@@ -343,6 +344,7 @@ static void test_geometry(const void *opaque)
reset(c);
const uint64_t dq7 = replicate(c, 0x80);
const uint64_t dq6 = replicate(c, 0x40);
+ const uint64_t dq3 = replicate(c, 0x08);
uint64_t byte_addr = 0;
for (int region = 0; region < nb_erase_regions; ++region) {
@@ -360,18 +362,29 @@ static void test_geometry(const void *opaque)
/* Erase and program sector. */
for (uint32_t i = 0; i < nb_sectors; ++i) {
sector_erase(c, byte_addr);
- /* Read toggle. */
+
+ /* Check that DQ3 is 0. */
+ g_assert_cmpint(flash_read(c, byte_addr) & dq3, ==, 0);
+ clock_step_next(); /* Step over the 50 us timeout. */
+
+ /* Check that DQ3 is 1. */
uint64_t status0 = flash_read(c, byte_addr);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+
/* DQ7 is 0 during an erase. */
g_assert_cmpint(status0 & dq7, ==, 0);
uint64_t status1 = flash_read(c, byte_addr);
+
/* DQ6 toggles during an erase. */
g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+
/* Wait for erase to complete. */
- clock_step_next();
+ wait_for_completion(c, byte_addr);
+
/* Ensure DQ6 has stopped toggling. */
g_assert_cmpint(flash_read(c, byte_addr), ==,
flash_read(c, byte_addr));
+
/* Now the data should be valid. */
g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
@@ -434,6 +447,44 @@ static void test_geometry(const void *opaque)
g_assert_cmpint(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
reset(c);
+ /*
+ * Program a word on each sector, erase one or two sectors per region, and
+ * verify that all of those, and only those, are erased.
+ */
+ byte_addr = 0;
+ for (int region = 0; region < nb_erase_regions; ++region) {
+ for (int i = 0; i < config->nb_blocs[region]; ++i) {
+ program(c, byte_addr, 0);
+ byte_addr += config->sector_len[region];
+ }
+ }
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, SECOND_UNLOCK_CMD);
+ unlock(c);
+ byte_addr = 0;
+ const uint64_t erase_cmd = replicate(c, SECTOR_ERASE_CMD);
+ for (int region = 0; region < nb_erase_regions; ++region) {
+ flash_write(c, byte_addr, erase_cmd);
+ if (c->nb_blocs[region] > 1) {
+ flash_write(c, byte_addr + c->sector_len[region], erase_cmd);
+ }
+ byte_addr += c->sector_len[region] * c->nb_blocs[region];
+ }
+
+ clock_step_next(); /* Step over the 50 us timeout. */
+ wait_for_completion(c, 0);
+ byte_addr = 0;
+ for (int region = 0; region < nb_erase_regions; ++region) {
+ for (int i = 0; i < config->nb_blocs[region]; ++i) {
+ if (i < 2) {
+ g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
+ } else {
+ g_assert_cmpint(flash_read(c, byte_addr), ==, 0);
+ }
+ byte_addr += config->sector_len[region];
+ }
+ }
+
qtest_quit(global_qtest);
}
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 08/10] block/pflash_cfi02: Implement multi-sector erase
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 08/10] block/pflash_cfi02: Implement multi-sector erase Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
0 siblings, 0 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Laurent Vivier, Thomas Huth, Stephen Checkoway,
qemu-block, Max Reitz, Paolo Bonzini
After two unlock cycles and a sector erase command, the AMD flash chips
start a 50 us erase time out. Any additional sector erase commands add a
sector to be erased and restart the 50 us timeout. During the timeout,
status bit DQ3 is cleared. After the time out, DQ3 is asserted during
erasure.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 94 +++++++++++++++++++++++++++++++--------
tests/pflash-cfi02-test.c | 59 ++++++++++++++++++++++--
2 files changed, 131 insertions(+), 22 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index cb1160eb35..21ceb0823b 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -30,7 +30,6 @@
*
* It does not implement software data protection as found in many real chips
* It does not implement erase suspend/resume commands
- * It does not implement multiple sectors erase
*/
#include "qemu/osdep.h"
@@ -106,6 +105,7 @@ struct PFlashCFI02 {
MemoryRegion orig_mem;
int rom_mode;
int read_counter; /* used for lazy switch-back to rom mode */
+ int sectors_to_erase;
char *name;
void *storage;
};
@@ -136,6 +136,22 @@ static inline void toggle_dq6(PFlashCFI02 *pfl)
pfl->status ^= pfl->interleave_multiplier * 0x40;
}
+/*
+ * Turn on DQ3.
+ */
+static inline void assert_dq3(PFlashCFI02 *pfl)
+{
+ pfl->status |= pfl->interleave_multiplier * 0x08;
+}
+
+/*
+ * Turn off DQ3.
+ */
+static inline void reset_dq3(PFlashCFI02 *pfl)
+{
+ pfl->status &= ~(pfl->interleave_multiplier * 0x08);
+}
+
/*
* Set up replicated mappings of the same region.
*/
@@ -159,11 +175,37 @@ static void pflash_register_memory(PFlashCFI02 *pfl, int rom_mode)
pfl->rom_mode = rom_mode;
}
-static void pflash_timer (void *opaque)
+static void pflash_timer(void *opaque)
{
PFlashCFI02 *pfl = opaque;
trace_pflash_timer_expired(pfl->cmd);
+ if (pfl->cmd == 0x30) {
+ /*
+ * Sector erase. If DQ3 is 0 when the timer expires, then the 50
+ * us erase timeout has expired so we need to start the timer for the
+ * sector erase algorithm. Otherwise, the erase completed and we should
+ * go back to read array mode.
+ */
+ if ((pfl->status & 0x08) == 0) {
+ assert_dq3(pfl);
+ /*
+ * CFI address 0x21 is "Typical timeout per individual block erase
+ * 2^N ms"
+ */
+ uint64_t timeout = ((1ULL << pfl->cfi_table[0x21]) *
+ pfl->sectors_to_erase) * 1000000;
+ timer_mod(&pfl->timer,
+ qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + timeout);
+ DPRINTF("%s: erase timeout fired; erasing %d sectors\n",
+ __func__, pfl->sectors_to_erase);
+ return;
+ }
+ DPRINTF("%s: sector erase complete\n", __func__);
+ pfl->sectors_to_erase = 0;
+ reset_dq3(pfl);
+ }
+
/* Reset flash */
toggle_dq7(pfl);
if (pfl->bypass) {
@@ -307,13 +349,30 @@ static void pflash_update(PFlashCFI02 *pfl, int offset, int size)
}
}
+static void pflash_sector_erase(PFlashCFI02 *pfl, hwaddr offset)
+{
+ uint64_t sector_len = pflash_sector_len(pfl, offset);
+ offset &= ~(sector_len - 1);
+ DPRINTF("%s: start sector erase at %0*" PRIx64 "-%0*" PRIx64 "\n",
+ __func__, pfl->bank_width * 2, offset,
+ pfl->bank_width * 2, offset + sector_len - 1);
+ if (!pfl->ro) {
+ uint8_t *p = pfl->storage;
+ memset(p + offset, 0xFF, sector_len);
+ pflash_update(pfl, offset, sector_len);
+ }
+ set_dq7(pfl, 0x00);
+ ++pfl->sectors_to_erase;
+ /* Set (or reset) the 50 us timer for additional erase commands. */
+ timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + 50000);
+}
+
static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
unsigned int width)
{
PFlashCFI02 *pfl = opaque;
uint8_t *p;
uint8_t cmd;
- uint32_t sector_len;
cmd = value;
if (pfl->cmd != 0xA0) {
@@ -486,20 +545,7 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
break;
case 0x30:
/* Sector erase */
- p = pfl->storage;
- sector_len = pflash_sector_len(pfl, offset);
- offset &= ~(sector_len - 1);
- DPRINTF("%s: start sector erase at %0*" PRIx64 "-%0*" PRIx64 "\n",
- __func__, pfl->bank_width * 2, offset,
- pfl->bank_width * 2, offset + sector_len - 1);
- if (!pfl->ro) {
- memset(p + offset, 0xFF, sector_len);
- pflash_update(pfl, offset, sector_len);
- }
- set_dq7(pfl, 0x00);
- /* Let's wait 1/2 second before sector erase is done */
- timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) +
- (NANOSECONDS_PER_SECOND / 2));
+ pflash_sector_erase(pfl, offset);
break;
default:
DPRINTF("%s: invalid command %02x (wc 5)\n", __func__, cmd);
@@ -513,7 +559,19 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* Ignore writes during chip erase */
return;
case 0x30:
- /* Ignore writes during sector erase */
+ /*
+ * If DQ3 is 0, additional sector erase commands can be
+ * written and anything else (other than an erase suspend) resets
+ * the device.
+ */
+ if ((pfl->status & 0x08) == 0) {
+ if (cmd == 0x30) {
+ pflash_sector_erase(pfl, offset);
+ } else {
+ goto reset_flash;
+ }
+ }
+ /* Ignore writes during the actual erase. */
return;
default:
/* Should never happen */
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index ae1cd4e54b..1cd9807c1b 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -37,6 +37,7 @@ typedef struct {
#define CFI_CMD 0x98
#define UNLOCK0_CMD 0xAA
#define UNLOCK1_CMD 0x55
+#define SECOND_UNLOCK_CMD 0x80
#define AUTOSELECT_CMD 0x90
#define RESET_CMD 0xF0
#define PROGRAM_CMD 0xA0
@@ -222,7 +223,7 @@ static void reset(const FlashConfig *c)
static void sector_erase(const FlashConfig *c, uint64_t byte_addr)
{
unlock(c);
- flash_cmd(c, UNLOCK0_ADDR, 0x80);
+ flash_cmd(c, UNLOCK0_ADDR, SECOND_UNLOCK_CMD);
unlock(c);
flash_write(c, byte_addr, replicate(c, SECTOR_ERASE_CMD));
}
@@ -261,7 +262,7 @@ static void program(const FlashConfig *c, uint64_t byte_addr, uint16_t data)
static void chip_erase(const FlashConfig *c)
{
unlock(c);
- flash_cmd(c, UNLOCK0_ADDR, 0x80);
+ flash_cmd(c, UNLOCK0_ADDR, SECOND_UNLOCK_CMD);
unlock(c);
flash_cmd(c, UNLOCK0_ADDR, CHIP_ERASE_CMD);
}
@@ -343,6 +344,7 @@ static void test_geometry(const void *opaque)
reset(c);
const uint64_t dq7 = replicate(c, 0x80);
const uint64_t dq6 = replicate(c, 0x40);
+ const uint64_t dq3 = replicate(c, 0x08);
uint64_t byte_addr = 0;
for (int region = 0; region < nb_erase_regions; ++region) {
@@ -360,18 +362,29 @@ static void test_geometry(const void *opaque)
/* Erase and program sector. */
for (uint32_t i = 0; i < nb_sectors; ++i) {
sector_erase(c, byte_addr);
- /* Read toggle. */
+
+ /* Check that DQ3 is 0. */
+ g_assert_cmpint(flash_read(c, byte_addr) & dq3, ==, 0);
+ clock_step_next(); /* Step over the 50 us timeout. */
+
+ /* Check that DQ3 is 1. */
uint64_t status0 = flash_read(c, byte_addr);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+
/* DQ7 is 0 during an erase. */
g_assert_cmpint(status0 & dq7, ==, 0);
uint64_t status1 = flash_read(c, byte_addr);
+
/* DQ6 toggles during an erase. */
g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+
/* Wait for erase to complete. */
- clock_step_next();
+ wait_for_completion(c, byte_addr);
+
/* Ensure DQ6 has stopped toggling. */
g_assert_cmpint(flash_read(c, byte_addr), ==,
flash_read(c, byte_addr));
+
/* Now the data should be valid. */
g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
@@ -434,6 +447,44 @@ static void test_geometry(const void *opaque)
g_assert_cmpint(flash_query(c, FLASH_ADDR(0)), ==, replicate(c, 0xBF));
reset(c);
+ /*
+ * Program a word on each sector, erase one or two sectors per region, and
+ * verify that all of those, and only those, are erased.
+ */
+ byte_addr = 0;
+ for (int region = 0; region < nb_erase_regions; ++region) {
+ for (int i = 0; i < config->nb_blocs[region]; ++i) {
+ program(c, byte_addr, 0);
+ byte_addr += config->sector_len[region];
+ }
+ }
+ unlock(c);
+ flash_cmd(c, UNLOCK0_ADDR, SECOND_UNLOCK_CMD);
+ unlock(c);
+ byte_addr = 0;
+ const uint64_t erase_cmd = replicate(c, SECTOR_ERASE_CMD);
+ for (int region = 0; region < nb_erase_regions; ++region) {
+ flash_write(c, byte_addr, erase_cmd);
+ if (c->nb_blocs[region] > 1) {
+ flash_write(c, byte_addr + c->sector_len[region], erase_cmd);
+ }
+ byte_addr += c->sector_len[region] * c->nb_blocs[region];
+ }
+
+ clock_step_next(); /* Step over the 50 us timeout. */
+ wait_for_completion(c, 0);
+ byte_addr = 0;
+ for (int region = 0; region < nb_erase_regions; ++region) {
+ for (int i = 0; i < config->nb_blocs[region]; ++i) {
+ if (i < 2) {
+ g_assert_cmpint(flash_read(c, byte_addr), ==, bank_mask(c));
+ } else {
+ g_assert_cmpint(flash_read(c, byte_addr), ==, 0);
+ }
+ byte_addr += config->sector_len[region];
+ }
+ }
+
qtest_quit(global_qtest);
}
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 09/10] block/pflash_cfi02: Implement erase suspend/resume
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
` (8 preceding siblings ...)
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 08/10] block/pflash_cfi02: Implement multi-sector erase Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 10/10] block/pflash_cfi02: Use the chip erase time specified in the CFI table Stephen Checkoway
10 siblings, 1 reply; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Max Reitz, qemu-block, Stephen Checkoway, Thomas Huth,
Laurent Vivier, Paolo Bonzini
During a sector erase (but not a chip erase), the embeded erase program
can be suspended. Once suspended, the sectors not selected for erasure
may be read and programmed. Autoselect mode is allowed during erase
suspend mode. Presumably, CFI queries are similarly allowed so this
commit allows them as well.
Since guest firmware can use status bits DQ7, DQ6, DQ3, and DQ2 to
determine the current state of sector erasure, these bits are properly
implemented.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 153 ++++++++++++++++++++++++++++++++++----
tests/pflash-cfi02-test.c | 102 +++++++++++++++++++++++++
2 files changed, 241 insertions(+), 14 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index 21ceb0823b..d9087cafff 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -29,7 +29,6 @@
* - CFI queries
*
* It does not implement software data protection as found in many real chips
- * It does not implement erase suspend/resume commands
*/
#include "qemu/osdep.h"
@@ -37,6 +36,7 @@
#include "hw/block/block.h"
#include "hw/block/flash.h"
#include "qapi/error.h"
+#include "qemu/bitmap.h"
#include "qemu/timer.h"
#include "sysemu/block-backend.h"
#include "qemu/host-utils.h"
@@ -72,6 +72,7 @@ struct PFlashCFI02 {
BlockBackend *blk;
uint32_t uniform_nb_blocs;
uint32_t uniform_sector_len;
+ uint32_t total_sectors;
uint32_t nb_blocs[PFLASH_MAX_ERASE_REGIONS];
uint32_t sector_len[PFLASH_MAX_ERASE_REGIONS];
uint64_t total_len;
@@ -106,6 +107,8 @@ struct PFlashCFI02 {
int rom_mode;
int read_counter; /* used for lazy switch-back to rom mode */
int sectors_to_erase;
+ uint64_t erase_time_remaining;
+ unsigned long *sector_erase_map;
char *name;
void *storage;
};
@@ -152,6 +155,14 @@ static inline void reset_dq3(PFlashCFI02 *pfl)
pfl->status &= ~(pfl->interleave_multiplier * 0x08);
}
+/*
+ * Toggle status bit DQ2.
+ */
+static inline void toggle_dq2(PFlashCFI02 *pfl)
+{
+ pfl->status ^= pfl->interleave_multiplier * 0x04;
+}
+
/*
* Set up replicated mappings of the same region.
*/
@@ -175,6 +186,29 @@ static void pflash_register_memory(PFlashCFI02 *pfl, int rom_mode)
pfl->rom_mode = rom_mode;
}
+/*
+ * Returns the time it takes to erase the number of sectors scheduled for
+ * erasure based on CFI address 0x21 which is "Typical timeout per individual
+ * block erase 2^N ms."
+ */
+static uint64_t pflash_erase_time(PFlashCFI02 *pfl)
+{
+ /*
+ * If there are no sectors to erase (which can happen if all of the sectors
+ * to be erased are protected), then erase takes 100 us. Protected sectors
+ * aren't supported so this should never happen.
+ */
+ return ((1ULL << pfl->cfi_table[0x21]) * pfl->sectors_to_erase) * SCALE_US;
+}
+
+/*
+ * Returns true if the device is currently in erase suspend mode.
+ */
+static inline bool pflash_erase_suspend_mode(PFlashCFI02 *pfl)
+{
+ return pfl->erase_time_remaining > 0;
+}
+
static void pflash_timer(void *opaque)
{
PFlashCFI02 *pfl = opaque;
@@ -189,12 +223,7 @@ static void pflash_timer(void *opaque)
*/
if ((pfl->status & 0x08) == 0) {
assert_dq3(pfl);
- /*
- * CFI address 0x21 is "Typical timeout per individual block erase
- * 2^N ms"
- */
- uint64_t timeout = ((1ULL << pfl->cfi_table[0x21]) *
- pfl->sectors_to_erase) * 1000000;
+ uint64_t timeout = pflash_erase_time(pfl);
timer_mod(&pfl->timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + timeout);
DPRINTF("%s: erase timeout fired; erasing %d sectors\n",
@@ -202,6 +231,7 @@ static void pflash_timer(void *opaque)
return;
}
DPRINTF("%s: sector erase complete\n", __func__);
+ bitmap_zero(pfl->sector_erase_map, pfl->total_sectors);
pfl->sectors_to_erase = 0;
reset_dq3(pfl);
}
@@ -240,25 +270,45 @@ static uint64_t pflash_data_read(PFlashCFI02 *pfl, hwaddr offset,
return ret;
}
+typedef struct {
+ uint32_t len;
+ uint32_t num;
+} SectorInfo;
+
/*
* offset should be a byte offset of the QEMU device and _not_ a device
* offset.
*/
-static uint32_t pflash_sector_len(PFlashCFI02 *pfl, hwaddr offset)
+static SectorInfo pflash_sector_info(PFlashCFI02 *pfl, hwaddr offset)
{
assert(offset < pfl->total_len);
int nb_regions = pfl->cfi_table[0x2C];
hwaddr addr = 0;
+ uint32_t sector_num = 0;
for (int i = 0; i < nb_regions; ++i) {
uint64_t region_size = (uint64_t)pfl->nb_blocs[i] * pfl->sector_len[i];
if (addr <= offset && offset < addr + region_size) {
- return pfl->sector_len[i];
+ return (SectorInfo) {
+ .len = pfl->sector_len[i],
+ .num = sector_num + (offset - addr) / pfl->sector_len[i],
+ };
}
+ sector_num += pfl->nb_blocs[i];
addr += region_size;
}
abort();
}
+/*
+ * Returns true if the offset refers to a flash sector that is currently being
+ * erased.
+ */
+static bool pflash_sector_is_erasing(PFlashCFI02 *pfl, hwaddr offset)
+{
+ long sector_num = pflash_sector_info(pfl, offset).num;
+ return test_bit(sector_num, pfl->sector_erase_map);
+}
+
static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
{
PFlashCFI02 *pfl = opaque;
@@ -285,6 +335,15 @@ static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
case 0x80:
/* We accept reads during second unlock sequence... */
case 0x00:
+ if (pflash_erase_suspend_mode(pfl) &&
+ pflash_sector_is_erasing(pfl, offset)) {
+ /* Toggle bit 2, but not 6. */
+ toggle_dq2(pfl);
+ /* Status register read */
+ ret = pfl->status;
+ DPRINTF("%s: status %" PRIx64 "\n", __func__, ret);
+ break;
+ }
/* Flash area read */
return pflash_data_read(pfl, offset, width);
case 0x90:
@@ -313,14 +372,16 @@ static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
DPRINTF("%s: ID " TARGET_FMT_plx " %" PRIx64 "\n",
__func__, device_addr & 0xFF, ret);
break;
- case 0xA0:
case 0x10:
case 0x30:
+ /* Toggle bit 2 during erase, but not program. */
+ toggle_dq2(pfl);
+ case 0xA0:
+ /* Toggle bit 6 */
+ toggle_dq6(pfl);
/* Status register read */
ret = pfl->status;
DPRINTF("%s: status %" PRIx64 "\n", __func__, ret);
- /* Toggle bit 6 */
- toggle_dq6(pfl);
break;
case 0x98:
/* CFI query mode */
@@ -351,7 +412,8 @@ static void pflash_update(PFlashCFI02 *pfl, int offset, int size)
static void pflash_sector_erase(PFlashCFI02 *pfl, hwaddr offset)
{
- uint64_t sector_len = pflash_sector_len(pfl, offset);
+ SectorInfo sector_info = pflash_sector_info(pfl, offset);
+ uint64_t sector_len = sector_info.len;
offset &= ~(sector_len - 1);
DPRINTF("%s: start sector erase at %0*" PRIx64 "-%0*" PRIx64 "\n",
__func__, pfl->bank_width * 2, offset,
@@ -363,6 +425,7 @@ static void pflash_sector_erase(PFlashCFI02 *pfl, hwaddr offset)
}
set_dq7(pfl, 0x00);
++pfl->sectors_to_erase;
+ set_bit(sector_info.num, pfl->sector_erase_map);
/* Set (or reset) the 50 us timer for additional erase commands. */
timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + 50000);
}
@@ -422,6 +485,25 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
pfl->cmd = 0x98;
return;
}
+ /* Handle erase resume in erase suspend mode, otherwise reset. */
+ if (cmd == 0x30) {
+ if (pflash_erase_suspend_mode(pfl)) {
+ /* Resume the erase. */
+ timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) +
+ pfl->erase_time_remaining);
+ pfl->erase_time_remaining = 0;
+ pfl->wcycle = 6;
+ pfl->cmd = 0x30;
+ set_dq7(pfl, 0x00);
+ assert_dq3(pfl);
+ return;
+ }
+ goto reset_flash;
+ }
+ /* Ignore erase suspend. */
+ if (cmd == 0xB0) {
+ return;
+ }
if (masked_addr != pfl->unlock_addr0 || cmd != 0xAA) {
DPRINTF("%s: unlock0 failed %04x %02x %04x\n",
__func__, masked_addr, cmd, pfl->unlock_addr0);
@@ -467,6 +549,14 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* We need another unlock sequence */
goto check_unlock0;
case 0xA0:
+ if (pflash_erase_suspend_mode(pfl) &&
+ pflash_sector_is_erasing(pfl, offset)) {
+ /* Ignore writes to erasing sectors. */
+ if (pfl->bypass) {
+ goto do_bypass;
+ }
+ goto reset_flash;
+ }
trace_pflash_data_write(offset, value, width, 0);
if (!pfl->ro) {
p = (uint8_t *)pfl->storage + offset;
@@ -525,6 +615,10 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
}
break;
case 5:
+ if (pflash_erase_suspend_mode(pfl)) {
+ /* Erasing is not supported in erase suspend mode. */
+ goto reset_flash;
+ }
switch (cmd) {
case 0x10:
if (masked_addr != pfl->unlock_addr0) {
@@ -559,6 +653,30 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* Ignore writes during chip erase */
return;
case 0x30:
+ if (cmd == 0xB0) {
+ /*
+ * If erase suspend happens during the erase timeout (so DQ3 is
+ * 0), then the device suspends erasing immediately. Set the
+ * remaining time to be the total time to erase. Otherwise,
+ * there is a maximum amount of time it can take to enter
+ * suspend mode. Let's ignore that and suspend immediately and
+ * set the remaining time to the actual time remaining on the
+ * timer.
+ */
+ if ((pfl->status & 0x08) == 0) {
+ pfl->erase_time_remaining = pflash_erase_time(pfl);
+ } else {
+ int64_t delta = timer_expire_time_ns(&pfl->timer) -
+ qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL);
+ /* Make sure we have a positive time remaining. */
+ pfl->erase_time_remaining = delta <= 0 ? 1 : delta;
+ }
+ reset_dq3(pfl);
+ timer_del(&pfl->timer);
+ pfl->wcycle = 0;
+ pfl->cmd = 0;
+ return;
+ }
/*
* If DQ3 is 0, additional sector erase commands can be
* written and anything else (other than an erase suspend) resets
@@ -723,10 +841,12 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
int num_devices = pfl->bank_width / pfl->device_width;
int nb_regions;
pfl->total_len = 0;
+ pfl->total_sectors = 0;
for (nb_regions = 0; nb_regions < PFLASH_MAX_ERASE_REGIONS; ++nb_regions) {
if (pfl->nb_blocs[nb_regions] == 0) {
break;
}
+ pfl->total_sectors += pfl->nb_blocs[nb_regions];
uint64_t sector_len_per_device = pfl->sector_len[nb_regions] /
num_devices;
@@ -761,6 +881,7 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->nb_blocs[0] = pfl->uniform_nb_blocs;
pfl->sector_len[0] = pfl->uniform_sector_len;
pfl->total_len = uniform_len;
+ pfl->total_sectors = pfl->uniform_nb_blocs;
} else if (uniform_len != 0 && uniform_len != pfl->total_len) {
error_setg(errp, "\"num-blocks\"*\"sector-length\" "
"different from \"num-blocks0\"*\'sector-length0\" + ... + "
@@ -785,6 +906,9 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->unlock_addr0 &= 0x7FF;
pfl->unlock_addr1 &= 0x7FF;
+ /* Allocate memory for a bitmap for sectors being erased. */
+ pfl->sector_erase_map = bitmap_new(pfl->total_sectors);
+
if (local_err) {
error_propagate(errp, local_err);
return;
@@ -892,7 +1016,7 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->cfi_table[0x44] = '0';
pfl->cfi_table[0x45] = 0x00; /* Address sensitive unlock required. */
- pfl->cfi_table[0x46] = 0x00; /* Erase suspend not supported. */
+ pfl->cfi_table[0x46] = 0x02; /* Erase suspend to read/write. */
pfl->cfi_table[0x47] = 0x00; /* Sector protect not supported. */
pfl->cfi_table[0x48] = 0x00; /* Temporary sector unprotect not supported. */
@@ -934,6 +1058,7 @@ static void pflash_cfi02_unrealize(DeviceState *dev, Error **errp)
{
PFlashCFI02 *pfl = PFLASH_CFI02(dev);
timer_del(&pfl->timer);
+ g_free(pfl->sector_erase_map);
}
static void pflash_cfi02_class_init(ObjectClass *klass, void *data)
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index 1cd9807c1b..38d6f6b809 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -45,6 +45,8 @@ typedef struct {
#define CHIP_ERASE_CMD 0x10
#define UNLOCK_BYPASS_CMD 0x20
#define UNLOCK_BYPASS_RESET_CMD 0x00
+#define ERASE_SUSPEND_CMD 0xB0
+#define ERASE_RESUME_CMD SECTOR_ERASE_CMD
typedef struct {
/* Interleave configuration. */
@@ -267,6 +269,16 @@ static void chip_erase(const FlashConfig *c)
flash_cmd(c, UNLOCK0_ADDR, CHIP_ERASE_CMD);
}
+static void erase_suspend(const FlashConfig *c)
+{
+ flash_cmd(c, FLASH_ADDR(0), ERASE_SUSPEND_CMD);
+}
+
+static void erase_resume(const FlashConfig *c)
+{
+ flash_cmd(c, FLASH_ADDR(0), ERASE_RESUME_CMD);
+}
+
/*
* Test flash commands with a variety of device geometry.
*/
@@ -345,6 +357,7 @@ static void test_geometry(const void *opaque)
const uint64_t dq7 = replicate(c, 0x80);
const uint64_t dq6 = replicate(c, 0x40);
const uint64_t dq3 = replicate(c, 0x08);
+ const uint64_t dq2 = replicate(c, 0x04);
uint64_t byte_addr = 0;
for (int region = 0; region < nb_erase_regions; ++region) {
@@ -485,6 +498,95 @@ static void test_geometry(const void *opaque)
}
}
+ /* Test erase suspend/resume during erase timeout. */
+ sector_erase(c, 0);
+ /*
+ * Check that DQ 3 is 0 and DQ6 and DQ2 are toggling in the sector being
+ * erased as well as in a sector not being erased.
+ */
+ byte_addr = c->sector_len[0];
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq3, ==, 0);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ status0 = flash_read(c, byte_addr);
+ status1 = flash_read(c, byte_addr);
+ g_assert_cmpint(status0 & dq3, ==, 0);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+
+ /*
+ * Check that after suspending, DQ6 does not toggle but DQ2 does toggle in
+ * an erase suspended sector but that neither toggle (we should be
+ * getting data) in a sector not being erased.
+ */
+ erase_suspend(c);
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq6, ==, status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ g_assert_cmpint(flash_read(c, byte_addr), ==, flash_read(c, byte_addr));
+
+ /* Check that after resuming, DQ3 is 1 and DQ6 and DQ2 toggle. */
+ erase_resume(c);
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ status0 = flash_read(c, byte_addr);
+ status1 = flash_read(c, byte_addr);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ wait_for_completion(c, 0);
+
+ /* Repeat this process but this time suspend after the timeout. */
+ sector_erase(c, 0);
+ clock_step_next();
+ /*
+ * Check that DQ 3 is 1 and DQ6 and DQ2 are toggling in the sector being
+ * erased as well as in a sector not being erased.
+ */
+ byte_addr = c->sector_len[0];
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ status0 = flash_read(c, byte_addr);
+ status1 = flash_read(c, byte_addr);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+
+ /*
+ * Check that after suspending, DQ6 does not toggle but DQ2 does toggle in
+ * an erase suspended sector but that neither toggle (we should be
+ * getting data) in a sector not being erased.
+ */
+ erase_suspend(c);
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq6, ==, status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ g_assert_cmpint(flash_read(c, byte_addr), ==, flash_read(c, byte_addr));
+
+ /* Check that after resuming, DQ3 is 1 and DQ6 and DQ2 toggle. */
+ erase_resume(c);
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ status0 = flash_read(c, byte_addr);
+ status1 = flash_read(c, byte_addr);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ wait_for_completion(c, 0);
+
qtest_quit(global_qtest);
}
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 09/10] block/pflash_cfi02: Implement erase suspend/resume
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 09/10] block/pflash_cfi02: Implement erase suspend/resume Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
0 siblings, 0 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel
Cc: Kevin Wolf, Laurent Vivier, Thomas Huth, Stephen Checkoway,
qemu-block, Max Reitz, Paolo Bonzini
During a sector erase (but not a chip erase), the embeded erase program
can be suspended. Once suspended, the sectors not selected for erasure
may be read and programmed. Autoselect mode is allowed during erase
suspend mode. Presumably, CFI queries are similarly allowed so this
commit allows them as well.
Since guest firmware can use status bits DQ7, DQ6, DQ3, and DQ2 to
determine the current state of sector erasure, these bits are properly
implemented.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 153 ++++++++++++++++++++++++++++++++++----
tests/pflash-cfi02-test.c | 102 +++++++++++++++++++++++++
2 files changed, 241 insertions(+), 14 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index 21ceb0823b..d9087cafff 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -29,7 +29,6 @@
* - CFI queries
*
* It does not implement software data protection as found in many real chips
- * It does not implement erase suspend/resume commands
*/
#include "qemu/osdep.h"
@@ -37,6 +36,7 @@
#include "hw/block/block.h"
#include "hw/block/flash.h"
#include "qapi/error.h"
+#include "qemu/bitmap.h"
#include "qemu/timer.h"
#include "sysemu/block-backend.h"
#include "qemu/host-utils.h"
@@ -72,6 +72,7 @@ struct PFlashCFI02 {
BlockBackend *blk;
uint32_t uniform_nb_blocs;
uint32_t uniform_sector_len;
+ uint32_t total_sectors;
uint32_t nb_blocs[PFLASH_MAX_ERASE_REGIONS];
uint32_t sector_len[PFLASH_MAX_ERASE_REGIONS];
uint64_t total_len;
@@ -106,6 +107,8 @@ struct PFlashCFI02 {
int rom_mode;
int read_counter; /* used for lazy switch-back to rom mode */
int sectors_to_erase;
+ uint64_t erase_time_remaining;
+ unsigned long *sector_erase_map;
char *name;
void *storage;
};
@@ -152,6 +155,14 @@ static inline void reset_dq3(PFlashCFI02 *pfl)
pfl->status &= ~(pfl->interleave_multiplier * 0x08);
}
+/*
+ * Toggle status bit DQ2.
+ */
+static inline void toggle_dq2(PFlashCFI02 *pfl)
+{
+ pfl->status ^= pfl->interleave_multiplier * 0x04;
+}
+
/*
* Set up replicated mappings of the same region.
*/
@@ -175,6 +186,29 @@ static void pflash_register_memory(PFlashCFI02 *pfl, int rom_mode)
pfl->rom_mode = rom_mode;
}
+/*
+ * Returns the time it takes to erase the number of sectors scheduled for
+ * erasure based on CFI address 0x21 which is "Typical timeout per individual
+ * block erase 2^N ms."
+ */
+static uint64_t pflash_erase_time(PFlashCFI02 *pfl)
+{
+ /*
+ * If there are no sectors to erase (which can happen if all of the sectors
+ * to be erased are protected), then erase takes 100 us. Protected sectors
+ * aren't supported so this should never happen.
+ */
+ return ((1ULL << pfl->cfi_table[0x21]) * pfl->sectors_to_erase) * SCALE_US;
+}
+
+/*
+ * Returns true if the device is currently in erase suspend mode.
+ */
+static inline bool pflash_erase_suspend_mode(PFlashCFI02 *pfl)
+{
+ return pfl->erase_time_remaining > 0;
+}
+
static void pflash_timer(void *opaque)
{
PFlashCFI02 *pfl = opaque;
@@ -189,12 +223,7 @@ static void pflash_timer(void *opaque)
*/
if ((pfl->status & 0x08) == 0) {
assert_dq3(pfl);
- /*
- * CFI address 0x21 is "Typical timeout per individual block erase
- * 2^N ms"
- */
- uint64_t timeout = ((1ULL << pfl->cfi_table[0x21]) *
- pfl->sectors_to_erase) * 1000000;
+ uint64_t timeout = pflash_erase_time(pfl);
timer_mod(&pfl->timer,
qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + timeout);
DPRINTF("%s: erase timeout fired; erasing %d sectors\n",
@@ -202,6 +231,7 @@ static void pflash_timer(void *opaque)
return;
}
DPRINTF("%s: sector erase complete\n", __func__);
+ bitmap_zero(pfl->sector_erase_map, pfl->total_sectors);
pfl->sectors_to_erase = 0;
reset_dq3(pfl);
}
@@ -240,25 +270,45 @@ static uint64_t pflash_data_read(PFlashCFI02 *pfl, hwaddr offset,
return ret;
}
+typedef struct {
+ uint32_t len;
+ uint32_t num;
+} SectorInfo;
+
/*
* offset should be a byte offset of the QEMU device and _not_ a device
* offset.
*/
-static uint32_t pflash_sector_len(PFlashCFI02 *pfl, hwaddr offset)
+static SectorInfo pflash_sector_info(PFlashCFI02 *pfl, hwaddr offset)
{
assert(offset < pfl->total_len);
int nb_regions = pfl->cfi_table[0x2C];
hwaddr addr = 0;
+ uint32_t sector_num = 0;
for (int i = 0; i < nb_regions; ++i) {
uint64_t region_size = (uint64_t)pfl->nb_blocs[i] * pfl->sector_len[i];
if (addr <= offset && offset < addr + region_size) {
- return pfl->sector_len[i];
+ return (SectorInfo) {
+ .len = pfl->sector_len[i],
+ .num = sector_num + (offset - addr) / pfl->sector_len[i],
+ };
}
+ sector_num += pfl->nb_blocs[i];
addr += region_size;
}
abort();
}
+/*
+ * Returns true if the offset refers to a flash sector that is currently being
+ * erased.
+ */
+static bool pflash_sector_is_erasing(PFlashCFI02 *pfl, hwaddr offset)
+{
+ long sector_num = pflash_sector_info(pfl, offset).num;
+ return test_bit(sector_num, pfl->sector_erase_map);
+}
+
static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
{
PFlashCFI02 *pfl = opaque;
@@ -285,6 +335,15 @@ static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
case 0x80:
/* We accept reads during second unlock sequence... */
case 0x00:
+ if (pflash_erase_suspend_mode(pfl) &&
+ pflash_sector_is_erasing(pfl, offset)) {
+ /* Toggle bit 2, but not 6. */
+ toggle_dq2(pfl);
+ /* Status register read */
+ ret = pfl->status;
+ DPRINTF("%s: status %" PRIx64 "\n", __func__, ret);
+ break;
+ }
/* Flash area read */
return pflash_data_read(pfl, offset, width);
case 0x90:
@@ -313,14 +372,16 @@ static uint64_t pflash_read(void *opaque, hwaddr offset, unsigned int width)
DPRINTF("%s: ID " TARGET_FMT_plx " %" PRIx64 "\n",
__func__, device_addr & 0xFF, ret);
break;
- case 0xA0:
case 0x10:
case 0x30:
+ /* Toggle bit 2 during erase, but not program. */
+ toggle_dq2(pfl);
+ case 0xA0:
+ /* Toggle bit 6 */
+ toggle_dq6(pfl);
/* Status register read */
ret = pfl->status;
DPRINTF("%s: status %" PRIx64 "\n", __func__, ret);
- /* Toggle bit 6 */
- toggle_dq6(pfl);
break;
case 0x98:
/* CFI query mode */
@@ -351,7 +412,8 @@ static void pflash_update(PFlashCFI02 *pfl, int offset, int size)
static void pflash_sector_erase(PFlashCFI02 *pfl, hwaddr offset)
{
- uint64_t sector_len = pflash_sector_len(pfl, offset);
+ SectorInfo sector_info = pflash_sector_info(pfl, offset);
+ uint64_t sector_len = sector_info.len;
offset &= ~(sector_len - 1);
DPRINTF("%s: start sector erase at %0*" PRIx64 "-%0*" PRIx64 "\n",
__func__, pfl->bank_width * 2, offset,
@@ -363,6 +425,7 @@ static void pflash_sector_erase(PFlashCFI02 *pfl, hwaddr offset)
}
set_dq7(pfl, 0x00);
++pfl->sectors_to_erase;
+ set_bit(sector_info.num, pfl->sector_erase_map);
/* Set (or reset) the 50 us timer for additional erase commands. */
timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + 50000);
}
@@ -422,6 +485,25 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
pfl->cmd = 0x98;
return;
}
+ /* Handle erase resume in erase suspend mode, otherwise reset. */
+ if (cmd == 0x30) {
+ if (pflash_erase_suspend_mode(pfl)) {
+ /* Resume the erase. */
+ timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) +
+ pfl->erase_time_remaining);
+ pfl->erase_time_remaining = 0;
+ pfl->wcycle = 6;
+ pfl->cmd = 0x30;
+ set_dq7(pfl, 0x00);
+ assert_dq3(pfl);
+ return;
+ }
+ goto reset_flash;
+ }
+ /* Ignore erase suspend. */
+ if (cmd == 0xB0) {
+ return;
+ }
if (masked_addr != pfl->unlock_addr0 || cmd != 0xAA) {
DPRINTF("%s: unlock0 failed %04x %02x %04x\n",
__func__, masked_addr, cmd, pfl->unlock_addr0);
@@ -467,6 +549,14 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* We need another unlock sequence */
goto check_unlock0;
case 0xA0:
+ if (pflash_erase_suspend_mode(pfl) &&
+ pflash_sector_is_erasing(pfl, offset)) {
+ /* Ignore writes to erasing sectors. */
+ if (pfl->bypass) {
+ goto do_bypass;
+ }
+ goto reset_flash;
+ }
trace_pflash_data_write(offset, value, width, 0);
if (!pfl->ro) {
p = (uint8_t *)pfl->storage + offset;
@@ -525,6 +615,10 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
}
break;
case 5:
+ if (pflash_erase_suspend_mode(pfl)) {
+ /* Erasing is not supported in erase suspend mode. */
+ goto reset_flash;
+ }
switch (cmd) {
case 0x10:
if (masked_addr != pfl->unlock_addr0) {
@@ -559,6 +653,30 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
/* Ignore writes during chip erase */
return;
case 0x30:
+ if (cmd == 0xB0) {
+ /*
+ * If erase suspend happens during the erase timeout (so DQ3 is
+ * 0), then the device suspends erasing immediately. Set the
+ * remaining time to be the total time to erase. Otherwise,
+ * there is a maximum amount of time it can take to enter
+ * suspend mode. Let's ignore that and suspend immediately and
+ * set the remaining time to the actual time remaining on the
+ * timer.
+ */
+ if ((pfl->status & 0x08) == 0) {
+ pfl->erase_time_remaining = pflash_erase_time(pfl);
+ } else {
+ int64_t delta = timer_expire_time_ns(&pfl->timer) -
+ qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL);
+ /* Make sure we have a positive time remaining. */
+ pfl->erase_time_remaining = delta <= 0 ? 1 : delta;
+ }
+ reset_dq3(pfl);
+ timer_del(&pfl->timer);
+ pfl->wcycle = 0;
+ pfl->cmd = 0;
+ return;
+ }
/*
* If DQ3 is 0, additional sector erase commands can be
* written and anything else (other than an erase suspend) resets
@@ -723,10 +841,12 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
int num_devices = pfl->bank_width / pfl->device_width;
int nb_regions;
pfl->total_len = 0;
+ pfl->total_sectors = 0;
for (nb_regions = 0; nb_regions < PFLASH_MAX_ERASE_REGIONS; ++nb_regions) {
if (pfl->nb_blocs[nb_regions] == 0) {
break;
}
+ pfl->total_sectors += pfl->nb_blocs[nb_regions];
uint64_t sector_len_per_device = pfl->sector_len[nb_regions] /
num_devices;
@@ -761,6 +881,7 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->nb_blocs[0] = pfl->uniform_nb_blocs;
pfl->sector_len[0] = pfl->uniform_sector_len;
pfl->total_len = uniform_len;
+ pfl->total_sectors = pfl->uniform_nb_blocs;
} else if (uniform_len != 0 && uniform_len != pfl->total_len) {
error_setg(errp, "\"num-blocks\"*\"sector-length\" "
"different from \"num-blocks0\"*\'sector-length0\" + ... + "
@@ -785,6 +906,9 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->unlock_addr0 &= 0x7FF;
pfl->unlock_addr1 &= 0x7FF;
+ /* Allocate memory for a bitmap for sectors being erased. */
+ pfl->sector_erase_map = bitmap_new(pfl->total_sectors);
+
if (local_err) {
error_propagate(errp, local_err);
return;
@@ -892,7 +1016,7 @@ static void pflash_cfi02_realize(DeviceState *dev, Error **errp)
pfl->cfi_table[0x44] = '0';
pfl->cfi_table[0x45] = 0x00; /* Address sensitive unlock required. */
- pfl->cfi_table[0x46] = 0x00; /* Erase suspend not supported. */
+ pfl->cfi_table[0x46] = 0x02; /* Erase suspend to read/write. */
pfl->cfi_table[0x47] = 0x00; /* Sector protect not supported. */
pfl->cfi_table[0x48] = 0x00; /* Temporary sector unprotect not supported. */
@@ -934,6 +1058,7 @@ static void pflash_cfi02_unrealize(DeviceState *dev, Error **errp)
{
PFlashCFI02 *pfl = PFLASH_CFI02(dev);
timer_del(&pfl->timer);
+ g_free(pfl->sector_erase_map);
}
static void pflash_cfi02_class_init(ObjectClass *klass, void *data)
diff --git a/tests/pflash-cfi02-test.c b/tests/pflash-cfi02-test.c
index 1cd9807c1b..38d6f6b809 100644
--- a/tests/pflash-cfi02-test.c
+++ b/tests/pflash-cfi02-test.c
@@ -45,6 +45,8 @@ typedef struct {
#define CHIP_ERASE_CMD 0x10
#define UNLOCK_BYPASS_CMD 0x20
#define UNLOCK_BYPASS_RESET_CMD 0x00
+#define ERASE_SUSPEND_CMD 0xB0
+#define ERASE_RESUME_CMD SECTOR_ERASE_CMD
typedef struct {
/* Interleave configuration. */
@@ -267,6 +269,16 @@ static void chip_erase(const FlashConfig *c)
flash_cmd(c, UNLOCK0_ADDR, CHIP_ERASE_CMD);
}
+static void erase_suspend(const FlashConfig *c)
+{
+ flash_cmd(c, FLASH_ADDR(0), ERASE_SUSPEND_CMD);
+}
+
+static void erase_resume(const FlashConfig *c)
+{
+ flash_cmd(c, FLASH_ADDR(0), ERASE_RESUME_CMD);
+}
+
/*
* Test flash commands with a variety of device geometry.
*/
@@ -345,6 +357,7 @@ static void test_geometry(const void *opaque)
const uint64_t dq7 = replicate(c, 0x80);
const uint64_t dq6 = replicate(c, 0x40);
const uint64_t dq3 = replicate(c, 0x08);
+ const uint64_t dq2 = replicate(c, 0x04);
uint64_t byte_addr = 0;
for (int region = 0; region < nb_erase_regions; ++region) {
@@ -485,6 +498,95 @@ static void test_geometry(const void *opaque)
}
}
+ /* Test erase suspend/resume during erase timeout. */
+ sector_erase(c, 0);
+ /*
+ * Check that DQ 3 is 0 and DQ6 and DQ2 are toggling in the sector being
+ * erased as well as in a sector not being erased.
+ */
+ byte_addr = c->sector_len[0];
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq3, ==, 0);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ status0 = flash_read(c, byte_addr);
+ status1 = flash_read(c, byte_addr);
+ g_assert_cmpint(status0 & dq3, ==, 0);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+
+ /*
+ * Check that after suspending, DQ6 does not toggle but DQ2 does toggle in
+ * an erase suspended sector but that neither toggle (we should be
+ * getting data) in a sector not being erased.
+ */
+ erase_suspend(c);
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq6, ==, status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ g_assert_cmpint(flash_read(c, byte_addr), ==, flash_read(c, byte_addr));
+
+ /* Check that after resuming, DQ3 is 1 and DQ6 and DQ2 toggle. */
+ erase_resume(c);
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ status0 = flash_read(c, byte_addr);
+ status1 = flash_read(c, byte_addr);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ wait_for_completion(c, 0);
+
+ /* Repeat this process but this time suspend after the timeout. */
+ sector_erase(c, 0);
+ clock_step_next();
+ /*
+ * Check that DQ 3 is 1 and DQ6 and DQ2 are toggling in the sector being
+ * erased as well as in a sector not being erased.
+ */
+ byte_addr = c->sector_len[0];
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ status0 = flash_read(c, byte_addr);
+ status1 = flash_read(c, byte_addr);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+
+ /*
+ * Check that after suspending, DQ6 does not toggle but DQ2 does toggle in
+ * an erase suspended sector but that neither toggle (we should be
+ * getting data) in a sector not being erased.
+ */
+ erase_suspend(c);
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq6, ==, status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ g_assert_cmpint(flash_read(c, byte_addr), ==, flash_read(c, byte_addr));
+
+ /* Check that after resuming, DQ3 is 1 and DQ6 and DQ2 toggle. */
+ erase_resume(c);
+ status0 = flash_read(c, 0);
+ status1 = flash_read(c, 0);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ status0 = flash_read(c, byte_addr);
+ status1 = flash_read(c, byte_addr);
+ g_assert_cmpint(status0 & dq3, ==, dq3);
+ g_assert_cmpint(status0 & dq6, ==, ~status1 & dq6);
+ g_assert_cmpint(status0 & dq2, ==, ~status1 & dq2);
+ wait_for_completion(c, 0);
+
qtest_quit(global_qtest);
}
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 10/10] block/pflash_cfi02: Use the chip erase time specified in the CFI table
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
` (9 preceding siblings ...)
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 09/10] block/pflash_cfi02: Implement erase suspend/resume Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
10 siblings, 1 reply; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel; +Cc: Kevin Wolf, Max Reitz, qemu-block, Stephen Checkoway
When erasing the chip, use the typical time specified in the CFI table
rather than arbitrarily selecting 5 seconds.
Since the currently unconfigurable value set in the table is 12, this
means a chip erase takes 4096 ms so this isn't a big change in behavior.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index d9087cafff..76c8af4365 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -633,9 +633,9 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
pflash_update(pfl, 0, pfl->total_len);
}
set_dq7(pfl, 0x00);
- /* Let's wait 5 seconds before chip erase is done */
+ /* Wait the time specified at CFI address 0x22. */
timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) +
- (NANOSECONDS_PER_SECOND * 5));
+ (1ULL << pfl->cfi_table[0x22]) * SCALE_MS);
break;
case 0x30:
/* Sector erase */
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
* [Qemu-devel] [PATCH v2 10/10] block/pflash_cfi02: Use the chip erase time specified in the CFI table
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 10/10] block/pflash_cfi02: Use the chip erase time specified in the CFI table Stephen Checkoway
@ 2019-04-09 2:01 ` Stephen Checkoway
0 siblings, 0 replies; 22+ messages in thread
From: Stephen Checkoway @ 2019-04-09 2:01 UTC (permalink / raw)
To: qemu-devel; +Cc: Kevin Wolf, Stephen Checkoway, qemu-block, Max Reitz
When erasing the chip, use the typical time specified in the CFI table
rather than arbitrarily selecting 5 seconds.
Since the currently unconfigurable value set in the table is 12, this
means a chip erase takes 4096 ms so this isn't a big change in behavior.
Signed-off-by: Stephen Checkoway <stephen.checkoway@oberlin.edu>
---
hw/block/pflash_cfi02.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/hw/block/pflash_cfi02.c b/hw/block/pflash_cfi02.c
index d9087cafff..76c8af4365 100644
--- a/hw/block/pflash_cfi02.c
+++ b/hw/block/pflash_cfi02.c
@@ -633,9 +633,9 @@ static void pflash_write(void *opaque, hwaddr offset, uint64_t value,
pflash_update(pfl, 0, pfl->total_len);
}
set_dq7(pfl, 0x00);
- /* Let's wait 5 seconds before chip erase is done */
+ /* Wait the time specified at CFI address 0x22. */
timer_mod(&pfl->timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) +
- (NANOSECONDS_PER_SECOND * 5));
+ (1ULL << pfl->cfi_table[0x22]) * SCALE_MS);
break;
case 0x30:
/* Sector erase */
--
2.20.1 (Apple Git-117)
^ permalink raw reply related [flat|nested] 22+ messages in thread
end of thread, other threads:[~2019-04-09 2:11 UTC | newest]
Thread overview: 22+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2019-04-09 2:01 [Qemu-devel] [PATCH v2 00/10] block/pflash_cfi02: Implement missing AMD pflash functionality Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 01/10] block/pflash_cfi02: Add test for supported commands Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 02/10] block/pflash_cfi02: Refactor, NFC intended Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 03/10] block/pflash_cfi02: Fix command address comparison Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 04/10] block/pflash_cfi02: Implement intereleaved flash devices Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 05/10] block/pflash_cfi02: Implement nonuniform sector sizes Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 06/10] block/pflash_cfi02: Fix CFI in autoselect mode Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 07/10] block/pflash_cfi02: Fix reset command not ignored during erase Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 08/10] block/pflash_cfi02: Implement multi-sector erase Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 09/10] block/pflash_cfi02: Implement erase suspend/resume Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
2019-04-09 2:01 ` [Qemu-devel] [PATCH v2 10/10] block/pflash_cfi02: Use the chip erase time specified in the CFI table Stephen Checkoway
2019-04-09 2:01 ` Stephen Checkoway
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).