* [Qemu-devel] [PATCH 01/19] unicore32-softmmu: Add unicore32-softmmu build support
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 02/19] unicore32-softmmu: Add coprocessor 0(sysctrl) and 1(ocd) instruction support gxt
` (18 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch adds unicore32-softmmu build support, include configure,
makefile, arch_init, and all missing functions needed by softmmu.
Although all missing functions are empty, unicore32-softmmu could
be build successfully.
By 20120804: change QEMU_ARCH_UNICORE32 to 0x4000
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
arch_init.c | 2 +
arch_init.h | 1 +
configure | 1 +
default-configs/unicore32-softmmu.mak | 1 +
hw/unicore32/Makefile.objs | 1 +
target-unicore32/Makefile.objs | 2 +-
target-unicore32/helper.c | 27 +++++++++++-----------
target-unicore32/machine.c | 23 +++++++++++++++++++
target-unicore32/op_helper.c | 24 +++++++++++++++++++-
target-unicore32/softmmu.c | 39 +++++++++++++++++++++++++++++++++
10 files changed, 106 insertions(+), 15 deletions(-)
create mode 100644 default-configs/unicore32-softmmu.mak
create mode 100644 hw/unicore32/Makefile.objs
create mode 100644 target-unicore32/machine.c
create mode 100644 target-unicore32/softmmu.c
diff --git a/arch_init.c b/arch_init.c
index 60823ba..7b65c48 100644
--- a/arch_init.c
+++ b/arch_init.c
@@ -91,6 +91,8 @@ int graphic_depth = 15;
#define QEMU_ARCH QEMU_ARCH_SPARC
#elif defined(TARGET_XTENSA)
#define QEMU_ARCH QEMU_ARCH_XTENSA
+#elif defined(TARGET_UNICORE32)
+#define QEMU_ARCH QEMU_ARCH_UNICORE32
#endif
const uint32_t arch_type = QEMU_ARCH;
diff --git a/arch_init.h b/arch_init.h
index 3dfea3b..547f93c 100644
--- a/arch_init.h
+++ b/arch_init.h
@@ -17,6 +17,7 @@ enum {
QEMU_ARCH_SPARC = 2048,
QEMU_ARCH_XTENSA = 4096,
QEMU_ARCH_OPENRISC = 8192,
+ QEMU_ARCH_UNICORE32 = 0x4000,
};
extern const uint32_t arch_type;
diff --git a/configure b/configure
index 280726c..efaff00 100755
--- a/configure
+++ b/configure
@@ -935,6 +935,7 @@ sparc64-softmmu \
s390x-softmmu \
xtensa-softmmu \
xtensaeb-softmmu \
+unicore32-softmmu \
"
fi
# the following are Linux specific
diff --git a/default-configs/unicore32-softmmu.mak b/default-configs/unicore32-softmmu.mak
new file mode 100644
index 0000000..5f04fe3
--- /dev/null
+++ b/default-configs/unicore32-softmmu.mak
@@ -0,0 +1 @@
+# Default configuration for unicore32-softmmu
diff --git a/hw/unicore32/Makefile.objs b/hw/unicore32/Makefile.objs
new file mode 100644
index 0000000..b6a3383
--- /dev/null
+++ b/hw/unicore32/Makefile.objs
@@ -0,0 +1 @@
+# For UniCore32 machines and boards
diff --git a/target-unicore32/Makefile.objs b/target-unicore32/Makefile.objs
index 2e0e093..6af1089 100644
--- a/target-unicore32/Makefile.objs
+++ b/target-unicore32/Makefile.objs
@@ -1,4 +1,4 @@
obj-y += translate.o op_helper.o helper.o cpu.o
-obj-$(CONFIG_SOFTMMU) += machine.o
+obj-$(CONFIG_SOFTMMU) += machine.o softmmu.o
$(obj)/op_helper.o: QEMU_CFLAGS += $(HELPER_CFLAGS)
diff --git a/target-unicore32/helper.c b/target-unicore32/helper.c
index 9fe4a37..9b8ff06 100644
--- a/target-unicore32/helper.c
+++ b/target-unicore32/helper.c
@@ -1,5 +1,5 @@
/*
- * Copyright (C) 2010-2011 GUAN Xue-tao
+ * Copyright (C) 2010-2012 Guan Xuetao
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -45,18 +45,26 @@ uint32_t HELPER(clz)(uint32_t x)
return clz32(x);
}
+#ifdef CONFIG_USER_ONLY
+void switch_mode(CPUUniCore32State *env, int mode)
+{
+ if (mode != ASR_MODE_USER) {
+ cpu_abort(env, "Tried to switch out of user mode\n");
+ }
+}
+
void do_interrupt(CPUUniCore32State *env)
{
- env->exception_index = -1;
+ cpu_abort(env, "NO interrupt in user mode\n");
}
-int uc32_cpu_handle_mmu_fault(CPUUniCore32State *env, target_ulong address, int rw,
- int mmu_idx)
+int uc32_cpu_handle_mmu_fault(CPUUniCore32State *env, target_ulong address,
+ int access_type, int mmu_idx)
{
- env->exception_index = UC32_EXCP_TRAP;
- env->cp0.c4_faultaddr = address;
+ cpu_abort(env, "NO mmu fault in user mode\n");
return 1;
}
+#endif
/* These should probably raise undefined insn exceptions. */
void HELPER(set_cp)(CPUUniCore32State *env, uint32_t insn, uint32_t val)
@@ -84,13 +92,6 @@ uint32_t HELPER(get_cp0)(CPUUniCore32State *env, uint32_t insn)
return 0;
}
-void switch_mode(CPUUniCore32State *env, int mode)
-{
- if (mode != ASR_MODE_USER) {
- cpu_abort(env, "Tried to switch out of user mode\n");
- }
-}
-
void HELPER(set_r29_banked)(CPUUniCore32State *env, uint32_t mode, uint32_t val)
{
cpu_abort(env, "banked r29 write\n");
diff --git a/target-unicore32/machine.c b/target-unicore32/machine.c
new file mode 100644
index 0000000..60b2ec1
--- /dev/null
+++ b/target-unicore32/machine.c
@@ -0,0 +1,23 @@
+/*
+ * Generic machine functions for UniCore32 ISA
+ *
+ * Copyright (C) 2010-2012 Guan Xuetao
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation, or any later version.
+ * See the COPYING file in the top-level directory.
+ */
+#include "hw/hw.h"
+
+void cpu_save(QEMUFile *f, void *opaque)
+{
+ hw_error("%s not supported yet.\n", __func__);
+}
+
+int cpu_load(QEMUFile *f, void *opaque, int version_id)
+{
+ hw_error("%s not supported yet.\n", __func__);
+
+ return 0;
+}
diff --git a/target-unicore32/op_helper.c b/target-unicore32/op_helper.c
index b954c30..6df30db 100644
--- a/target-unicore32/op_helper.c
+++ b/target-unicore32/op_helper.c
@@ -1,7 +1,7 @@
/*
* UniCore32 helper routines
*
- * Copyright (C) 2010-2011 GUAN Xue-tao
+ * Copyright (C) 2010-2012 Guan Xuetao
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -248,3 +248,25 @@ uint32_t HELPER(ror_cc)(uint32_t x, uint32_t i)
return ((uint32_t)x >> shift) | (x << (32 - shift));
}
}
+
+#ifndef CONFIG_USER_ONLY
+#define MMUSUFFIX _mmu
+
+#define SHIFT 0
+#include "softmmu_template.h"
+
+#define SHIFT 1
+#include "softmmu_template.h"
+
+#define SHIFT 2
+#include "softmmu_template.h"
+
+#define SHIFT 3
+#include "softmmu_template.h"
+
+void tlb_fill(CPUUniCore32State *env1, target_ulong addr, int is_write,
+ int mmu_idx, uintptr_t retaddr)
+{
+ cpu_abort(env, "%s not supported yet\n", __func__);
+}
+#endif
diff --git a/target-unicore32/softmmu.c b/target-unicore32/softmmu.c
new file mode 100644
index 0000000..6fec77e
--- /dev/null
+++ b/target-unicore32/softmmu.c
@@ -0,0 +1,39 @@
+/*
+ * Softmmu related functions
+ *
+ * Copyright (C) 2010-2012 Guan Xuetao
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation, or any later version.
+ * See the COPYING file in the top-level directory.
+ */
+#ifdef CONFIG_USER_ONLY
+#error This file only exist under softmmu circumstance
+#endif
+
+#include <cpu.h>
+
+void switch_mode(CPUUniCore32State *env, int mode)
+{
+ cpu_abort(env, "%s not supported yet\n", __func__);
+}
+
+void do_interrupt(CPUUniCore32State *env)
+{
+ cpu_abort(env, "%s not supported yet\n", __func__);
+}
+
+int uc32_cpu_handle_mmu_fault(CPUUniCore32State *env, target_ulong address,
+ int access_type, int mmu_idx)
+{
+ cpu_abort(env, "%s not supported yet\n", __func__);
+ return 1;
+}
+
+target_phys_addr_t cpu_get_phys_page_debug(CPUUniCore32State *env,
+ target_ulong addr)
+{
+ cpu_abort(env, "%s not supported yet\n", __func__);
+ return addr;
+}
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 02/19] unicore32-softmmu: Add coprocessor 0(sysctrl) and 1(ocd) instruction support
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 01/19] unicore32-softmmu: Add unicore32-softmmu build support gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 03/19] unicore32-softmmu: Make UniCore32 cpuid & exceptions correct and runable gxt
` (17 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
Coprocessor 0 is system control coprocessor, and we need get/set its contents.
Also, all cache/tlb ops shoule be implemented here, but just ignored with no harm.
Coprocessor 1 is OCD (on-chip-debugger), which is used for faked console,
so we could output chars to this console without graphic card.
TODO: curses display should be added lator for screen output.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
target-unicore32/helper.c | 185 +++++++++++++++++++++++++++++++++---------
target-unicore32/helper.h | 17 ++---
target-unicore32/translate.c | 80 ++++++++++++++++++-
3 files changed, 233 insertions(+), 49 deletions(-)
diff --git a/target-unicore32/helper.c b/target-unicore32/helper.c
index 9b8ff06..f9f1960 100644
--- a/target-unicore32/helper.c
+++ b/target-unicore32/helper.c
@@ -14,6 +14,14 @@
#include "helper.h"
#include "host-utils.h"
+#undef DEBUG_UC32
+
+#ifdef DEBUG_UC32
+#define DPRINTF(fmt, ...) printf("%s: " fmt , __func__, ## __VA_ARGS__)
+#else
+#define DPRINTF(fmt, ...) do {} while (0)
+#endif
+
CPUUniCore32State *uc32_cpu_init(const char *cpu_model)
{
UniCore32CPU *cpu;
@@ -45,6 +53,146 @@ uint32_t HELPER(clz)(uint32_t x)
return clz32(x);
}
+#ifndef CONFIG_USER_ONLY
+void helper_cp0_set(CPUUniCore32State *env, uint32_t val, uint32_t creg,
+ uint32_t cop)
+{
+ /*
+ * movc pp.nn, rn, #imm9
+ * rn: UCOP_REG_D
+ * nn: UCOP_REG_N
+ * 1: sys control reg.
+ * 2: page table base reg.
+ * 3: data fault status reg.
+ * 4: insn fault status reg.
+ * 5: cache op. reg.
+ * 6: tlb op. reg.
+ * imm9: split UCOP_IMM10 with bit5 is 0
+ */
+ switch (creg) {
+ case 1:
+ if (cop != 0) {
+ goto unrecognized;
+ }
+ env->cp0.c1_sys = val;
+ break;
+ case 2:
+ if (cop != 0) {
+ goto unrecognized;
+ }
+ env->cp0.c2_base = val;
+ break;
+ case 3:
+ if (cop != 0) {
+ goto unrecognized;
+ }
+ env->cp0.c3_faultstatus = val;
+ break;
+ case 4:
+ if (cop != 0) {
+ goto unrecognized;
+ }
+ env->cp0.c4_faultaddr = val;
+ break;
+ case 5:
+ switch (cop) {
+ case 28:
+ DPRINTF("Invalidate Entire I&D cache\n");
+ return;
+ case 20:
+ DPRINTF("Invalidate Entire Icache\n");
+ return;
+ case 12:
+ DPRINTF("Invalidate Entire Dcache\n");
+ return;
+ case 10:
+ DPRINTF("Clean Entire Dcache\n");
+ return;
+ case 14:
+ DPRINTF("Flush Entire Dcache\n");
+ return;
+ case 13:
+ DPRINTF("Invalidate Dcache line\n");
+ return;
+ case 11:
+ DPRINTF("Clean Dcache line\n");
+ return;
+ case 15:
+ DPRINTF("Flush Dcache line\n");
+ return;
+ }
+ break;
+ case 6:
+ if ((cop <= 6) && (cop >= 2)) {
+ /* invalid all tlb */
+ tlb_flush(env, 1);
+ return;
+ }
+ break;
+ default:
+ goto unrecognized;
+ }
+ return;
+unrecognized:
+ DPRINTF("Wrong register (%d) or wrong operation (%d) in cp0_set!\n",
+ creg, cop);
+}
+
+uint32_t helper_cp0_get(CPUUniCore32State *env, uint32_t creg, uint32_t cop)
+{
+ /*
+ * movc rd, pp.nn, #imm9
+ * rd: UCOP_REG_D
+ * nn: UCOP_REG_N
+ * 0: cpuid and cachetype
+ * 1: sys control reg.
+ * 2: page table base reg.
+ * 3: data fault status reg.
+ * 4: insn fault status reg.
+ * imm9: split UCOP_IMM10 with bit5 is 0
+ */
+ switch (creg) {
+ case 0:
+ switch (cop) {
+ case 0:
+ return env->cp0.c0_cpuid;
+ case 1:
+ return env->cp0.c0_cachetype;
+ }
+ break;
+ case 1:
+ if (cop == 0) {
+ return env->cp0.c1_sys;
+ }
+ break;
+ case 2:
+ if (cop == 0) {
+ return env->cp0.c2_base;
+ }
+ break;
+ case 3:
+ if (cop == 0) {
+ return env->cp0.c3_faultstatus;
+ }
+ break;
+ case 4:
+ if (cop == 0) {
+ return env->cp0.c4_faultaddr;
+ }
+ break;
+ }
+ DPRINTF("Wrong register (%d) or wrong operation (%d) in cp0_set!\n",
+ creg, cop);
+ return 0;
+}
+
+void helper_cp1_putc(target_ulong x)
+{
+ /* TODO: curses display should be added here for screen output. */
+ DPRINTF("%c", x);
+}
+#endif
+
#ifdef CONFIG_USER_ONLY
void switch_mode(CPUUniCore32State *env, int mode)
{
@@ -66,43 +214,6 @@ int uc32_cpu_handle_mmu_fault(CPUUniCore32State *env, target_ulong address,
}
#endif
-/* These should probably raise undefined insn exceptions. */
-void HELPER(set_cp)(CPUUniCore32State *env, uint32_t insn, uint32_t val)
-{
- int op1 = (insn >> 8) & 0xf;
- cpu_abort(env, "cp%i insn %08x\n", op1, insn);
- return;
-}
-
-uint32_t HELPER(get_cp)(CPUUniCore32State *env, uint32_t insn)
-{
- int op1 = (insn >> 8) & 0xf;
- cpu_abort(env, "cp%i insn %08x\n", op1, insn);
- return 0;
-}
-
-void HELPER(set_cp0)(CPUUniCore32State *env, uint32_t insn, uint32_t val)
-{
- cpu_abort(env, "cp0 insn %08x\n", insn);
-}
-
-uint32_t HELPER(get_cp0)(CPUUniCore32State *env, uint32_t insn)
-{
- cpu_abort(env, "cp0 insn %08x\n", insn);
- return 0;
-}
-
-void HELPER(set_r29_banked)(CPUUniCore32State *env, uint32_t mode, uint32_t val)
-{
- cpu_abort(env, "banked r29 write\n");
-}
-
-uint32_t HELPER(get_r29_banked)(CPUUniCore32State *env, uint32_t mode)
-{
- cpu_abort(env, "banked r29 read\n");
- return 0;
-}
-
/* UniCore-F64 support. We follow the convention used for F64 instrunctions:
Single precition routines have a "s" suffix, double precision a
"d" suffix. */
diff --git a/target-unicore32/helper.h b/target-unicore32/helper.h
index 5a3b8a4..305318a 100644
--- a/target-unicore32/helper.h
+++ b/target-unicore32/helper.h
@@ -1,5 +1,5 @@
/*
- * Copyright (C) 2010-2011 GUAN Xue-tao
+ * Copyright (C) 2010-2012 Guan Xuetao
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -8,6 +8,12 @@
*/
#include "def-helper.h"
+#ifndef CONFIG_USER_ONLY
+DEF_HELPER_4(cp0_set, void, env, i32, i32, i32)
+DEF_HELPER_3(cp0_get, i32, env, i32, i32)
+DEF_HELPER_1(cp1_putc, void, i32)
+#endif
+
DEF_HELPER_1(clz, i32, i32)
DEF_HELPER_1(clo, i32, i32)
@@ -16,12 +22,6 @@ DEF_HELPER_1(exception, void, i32)
DEF_HELPER_2(asr_write, void, i32, i32)
DEF_HELPER_0(asr_read, i32)
-DEF_HELPER_3(set_cp0, void, env, i32, i32)
-DEF_HELPER_2(get_cp0, i32, env, i32)
-
-DEF_HELPER_3(set_cp, void, env, i32, i32)
-DEF_HELPER_2(get_cp, i32, env, i32)
-
DEF_HELPER_1(get_user_reg, i32, i32)
DEF_HELPER_2(set_user_reg, void, i32, i32)
@@ -38,9 +38,6 @@ DEF_HELPER_2(shr_cc, i32, i32, i32)
DEF_HELPER_2(sar_cc, i32, i32, i32)
DEF_HELPER_2(ror_cc, i32, i32, i32)
-DEF_HELPER_2(get_r29_banked, i32, env, i32)
-DEF_HELPER_3(set_r29_banked, void, env, i32, i32)
-
DEF_HELPER_1(ucf64_get_fpscr, i32, env)
DEF_HELPER_2(ucf64_set_fpscr, void, env, i32)
diff --git a/target-unicore32/translate.c b/target-unicore32/translate.c
index 9793d14..e37d5be 100644
--- a/target-unicore32/translate.c
+++ b/target-unicore32/translate.c
@@ -1,7 +1,7 @@
/*
* UniCore32 translation
*
- * Copyright (C) 2010-2011 GUAN Xue-tao
+ * Copyright (C) 2010-2012 Guan Xuetao
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
@@ -176,6 +176,73 @@ static void store_reg(DisasContext *s, int reg, TCGv var)
"Illegal UniCore32 instruction %x at line %d!", \
insn, __LINE__)
+#ifndef CONFIG_USER_ONLY
+static void disas_cp0_insn(CPUUniCore32State *env, DisasContext *s,
+ uint32_t insn)
+{
+ TCGv tmp, tmp2, tmp3;
+ if ((insn & 0xfe000000) == 0xe0000000) {
+ tmp2 = new_tmp();
+ tmp3 = new_tmp();
+ tcg_gen_movi_i32(tmp2, UCOP_REG_N);
+ tcg_gen_movi_i32(tmp3, UCOP_IMM10);
+ if (UCOP_SET_L) {
+ tmp = new_tmp();
+ gen_helper_cp0_get(tmp, cpu_env, tmp2, tmp3);
+ store_reg(s, UCOP_REG_D, tmp);
+ } else {
+ tmp = load_reg(s, UCOP_REG_D);
+ gen_helper_cp0_set(cpu_env, tmp, tmp2, tmp3);
+ dead_tmp(tmp);
+ }
+ dead_tmp(tmp2);
+ dead_tmp(tmp3);
+ return;
+ }
+ ILLEGAL;
+}
+
+static void disas_ocd_insn(CPUUniCore32State *env, DisasContext *s,
+ uint32_t insn)
+{
+ TCGv tmp;
+
+ if ((insn & 0xff003fff) == 0xe1000400) {
+ /*
+ * movc rd, pp.nn, #imm9
+ * rd: UCOP_REG_D
+ * nn: UCOP_REG_N (must be 0)
+ * imm9: 0
+ */
+ if (UCOP_REG_N == 0) {
+ tmp = new_tmp();
+ tcg_gen_movi_i32(tmp, 0);
+ store_reg(s, UCOP_REG_D, tmp);
+ return;
+ } else {
+ ILLEGAL;
+ }
+ }
+ if ((insn & 0xff003fff) == 0xe0000401) {
+ /*
+ * movc pp.nn, rn, #imm9
+ * rn: UCOP_REG_D
+ * nn: UCOP_REG_N (must be 1)
+ * imm9: 1
+ */
+ if (UCOP_REG_N == 1) {
+ tmp = load_reg(s, UCOP_REG_D);
+ gen_helper_cp1_putc(tmp);
+ dead_tmp(tmp);
+ return;
+ } else {
+ ILLEGAL;
+ }
+ }
+ ILLEGAL;
+}
+#endif
+
static inline void gen_set_asr(TCGv var, uint32_t mask)
{
TCGv tmp_mask = tcg_const_i32(mask);
@@ -1124,9 +1191,18 @@ static void gen_exception_return(DisasContext *s, TCGv pc)
s->is_jmp = DISAS_UPDATE;
}
-static void disas_coproc_insn(CPUUniCore32State *env, DisasContext *s, uint32_t insn)
+static void disas_coproc_insn(CPUUniCore32State *env, DisasContext *s,
+ uint32_t insn)
{
switch (UCOP_CPNUM) {
+#ifndef CONFIG_USER_ONLY
+ case 0:
+ disas_cp0_insn(env, s, insn);
+ break;
+ case 1:
+ disas_ocd_insn(env, s, insn);
+ break;
+#endif
case 2:
disas_ucf64_insn(env, s, insn);
break;
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 03/19] unicore32-softmmu: Make UniCore32 cpuid & exceptions correct and runable
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 01/19] unicore32-softmmu: Add unicore32-softmmu build support gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 02/19] unicore32-softmmu: Add coprocessor 0(sysctrl) and 1(ocd) instruction support gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 04/19] target-unicore32: Drop UC32_CPUID macros gxt
` (16 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch initializes the cpuid to exactly correct value because
linux kernel will check it.
In addition, the exception types are specified in proper situations.
Then it could make exceptions generated correctly and timely.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
cpu-exec.c | 1 +
linux-user/main.c | 3 ++-
target-unicore32/cpu.c | 19 ++++++++++++++-----
target-unicore32/cpu.h | 14 ++++++++------
4 files changed, 25 insertions(+), 12 deletions(-)
diff --git a/cpu-exec.c b/cpu-exec.c
index 543460c..6c4e516 100644
--- a/cpu-exec.c
+++ b/cpu-exec.c
@@ -447,6 +447,7 @@ int cpu_exec(CPUArchState *env)
#elif defined(TARGET_UNICORE32)
if (interrupt_request & CPU_INTERRUPT_HARD
&& !(env->uncached_asr & ASR_I)) {
+ env->exception_index = UC32_EXCP_INTR;
do_interrupt(env);
next_tb = 0;
}
diff --git a/linux-user/main.c b/linux-user/main.c
index 53714de..9d921aa 100644
--- a/linux-user/main.c
+++ b/linux-user/main.c
@@ -958,7 +958,8 @@ void cpu_loop(CPUUniCore32State *env)
}
}
break;
- case UC32_EXCP_TRAP:
+ case UC32_EXCP_DTRAP:
+ case UC32_EXCP_ITRAP:
info.si_signo = SIGSEGV;
info.si_errno = 0;
/* XXX: check env->error_code */
diff --git a/target-unicore32/cpu.c b/target-unicore32/cpu.c
index de63f58..3425bbe 100644
--- a/target-unicore32/cpu.c
+++ b/target-unicore32/cpu.c
@@ -1,7 +1,7 @@
/*
* QEMU UniCore32 CPU
*
- * Copyright (c) 2010-2011 GUAN Xue-tao
+ * Copyright (c) 2010-2012 Guan Xuetao
* Copyright (c) 2012 SUSE LINUX Products GmbH
*
* This program is free software; you can redistribute it and/or modify
@@ -32,13 +32,16 @@ static void unicore_ii_cpu_initfn(Object *obj)
UniCore32CPU *cpu = UNICORE32_CPU(obj);
CPUUniCore32State *env = &cpu->env;
- env->cp0.c0_cpuid = 0x40010863;
+ env->cp0.c0_cpuid = 0x4d000863;
+ env->cp0.c0_cachetype = 0x0d152152;
+ env->cp0.c1_sys = 0x2000;
+ env->cp0.c2_base = 0x0;
+ env->cp0.c3_faultstatus = 0x0;
+ env->cp0.c4_faultaddr = 0x0;
+ env->ucf64.xregs[UC32_UCF64_FPSCR] = 0;
set_feature(env, UC32_HWCAP_CMOV);
set_feature(env, UC32_HWCAP_UCF64);
- env->ucf64.xregs[UC32_UCF64_FPSCR] = 0;
- env->cp0.c0_cachetype = 0x1dd20d2;
- env->cp0.c1_sys = 0x00090078;
}
static void uc32_any_cpu_initfn(Object *obj)
@@ -47,6 +50,7 @@ static void uc32_any_cpu_initfn(Object *obj)
CPUUniCore32State *env = &cpu->env;
env->cp0.c0_cpuid = 0xffffffff;
+ env->ucf64.xregs[UC32_UCF64_FPSCR] = 0;
set_feature(env, UC32_HWCAP_CMOV);
set_feature(env, UC32_HWCAP_UCF64);
@@ -65,8 +69,13 @@ static void uc32_cpu_initfn(Object *obj)
cpu_exec_init(env);
env->cpu_model_str = object_get_typename(obj);
+#ifdef CONFIG_USER_ONLY
env->uncached_asr = ASR_MODE_USER;
env->regs[31] = 0;
+#else
+ env->uncached_asr = ASR_MODE_PRIV;
+ env->regs[31] = 0x03000000;
+#endif
tlb_flush(env, 1);
}
diff --git a/target-unicore32/cpu.h b/target-unicore32/cpu.h
index 81c14ff..d14fde5 100644
--- a/target-unicore32/cpu.h
+++ b/target-unicore32/cpu.h
@@ -1,15 +1,15 @@
/*
* UniCore32 virtual CPU header
*
- * Copyright (C) 2010-2011 GUAN Xue-tao
+ * Copyright (C) 2010-2012 Guan Xuetao
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation, or (at your option) any
* later version. See the COPYING file in the top-level directory.
*/
-#ifndef __CPU_UC32_H__
-#define __CPU_UC32_H__
+#ifndef QEMU_UNICORE32_CPU_H
+#define QEMU_UNICORE32_CPU_H
#define TARGET_LONG_BITS 32
#define TARGET_PAGE_BITS 12
@@ -89,8 +89,10 @@ typedef struct CPUUniCore32State {
#define ASR_NZCV (ASR_N | ASR_Z | ASR_C | ASR_V)
#define ASR_RESERVED (~(ASR_M | ASR_I | ASR_NZCV))
-#define UC32_EXCP_PRIV (ASR_MODE_PRIV)
-#define UC32_EXCP_TRAP (ASR_MODE_TRAP)
+#define UC32_EXCP_PRIV (1)
+#define UC32_EXCP_ITRAP (2)
+#define UC32_EXCP_DTRAP (3)
+#define UC32_EXCP_INTR (4)
/* Return the current ASR value. */
target_ulong cpu_asr_read(CPUUniCore32State *env1);
@@ -189,4 +191,4 @@ static inline bool cpu_has_work(CPUUniCore32State *env)
(CPU_INTERRUPT_HARD | CPU_INTERRUPT_EXITTB);
}
-#endif /* __CPU_UC32_H__ */
+#endif /* QEMU_UNICORE32_CPU_H */
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 04/19] target-unicore32: Drop UC32_CPUID macros
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (2 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 03/19] unicore32-softmmu: Make UniCore32 cpuid & exceptions correct and runable gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 05/19] unicore32-softmmu: Implement softmmu specific functions gxt
` (15 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Andreas Färber <afaerber@suse.de>
Any code that depends on a particular CPU type can now go through
callbacks on the QOM UniCore32CPUClass.
Signed-off-by: Andreas Färber <afaerber@suse.de
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
target-unicore32/cpu.h | 4 ----
1 files changed, 0 insertions(+), 4 deletions(-)
diff --git a/target-unicore32/cpu.h b/target-unicore32/cpu.h
index d14fde5..06508a1 100644
--- a/target-unicore32/cpu.h
+++ b/target-unicore32/cpu.h
@@ -122,10 +122,6 @@ void cpu_asr_write(CPUUniCore32State *env1, target_ulong val, target_ulong mask)
#define UC32_HWCAP_CMOV 4 /* 1 << 2 */
#define UC32_HWCAP_UCF64 8 /* 1 << 3 */
-#define UC32_CPUID(env) (env->cp0.c0_cpuid)
-#define UC32_CPUID_UCV2 0x40010863
-#define UC32_CPUID_ANY 0xffffffff
-
#define cpu_init uc32_cpu_init
#define cpu_exec uc32_cpu_exec
#define cpu_signal_handler uc32_cpu_signal_handler
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 05/19] unicore32-softmmu: Implement softmmu specific functions
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (3 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 04/19] target-unicore32: Drop UC32_CPUID macros gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 06/19] unicore32-softmmu: Make sure that kernel can access user space gxt
` (14 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch implements softmmu specific functions, include tlb_fill,
switch_mode, do_interrupt and uc32_cpu_handle_mmu_fault.
So the full exception handlers and page table walking could work now.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
target-unicore32/op_helper.c | 22 ++++-
target-unicore32/softmmu.c | 236 +++++++++++++++++++++++++++++++++++++++++-
2 files changed, 253 insertions(+), 5 deletions(-)
diff --git a/target-unicore32/op_helper.c b/target-unicore32/op_helper.c
index 6df30db..c63789d 100644
--- a/target-unicore32/op_helper.c
+++ b/target-unicore32/op_helper.c
@@ -267,6 +267,26 @@ uint32_t HELPER(ror_cc)(uint32_t x, uint32_t i)
void tlb_fill(CPUUniCore32State *env1, target_ulong addr, int is_write,
int mmu_idx, uintptr_t retaddr)
{
- cpu_abort(env, "%s not supported yet\n", __func__);
+ TranslationBlock *tb;
+ CPUUniCore32State *saved_env;
+ unsigned long pc;
+ int ret;
+
+ saved_env = env;
+ env = env1;
+ ret = uc32_cpu_handle_mmu_fault(env, addr, is_write, mmu_idx);
+ if (unlikely(ret)) {
+ if (retaddr) {
+ /* now we have a real cpu fault */
+ pc = (unsigned long)retaddr;
+ tb = tb_find_pc(pc);
+ if (tb) {/* the PC is inside the translated code.
+ It means that we have a virtual CPU fault */
+ cpu_restore_state(tb, env, pc);
+ }
+ }
+ cpu_loop_exit(env);
+ }
+ env = saved_env;
}
#endif
diff --git a/target-unicore32/softmmu.c b/target-unicore32/softmmu.c
index 6fec77e..373f94b 100644
--- a/target-unicore32/softmmu.c
+++ b/target-unicore32/softmmu.c
@@ -14,21 +14,249 @@
#include <cpu.h>
+#undef DEBUG_UC32
+
+#ifdef DEBUG_UC32
+#define DPRINTF(fmt, ...) printf("%s: " fmt , __func__, ## __VA_ARGS__)
+#else
+#define DPRINTF(fmt, ...) do {} while (0)
+#endif
+
+#define SUPERPAGE_SIZE (1 << 22)
+#define UC32_PAGETABLE_READ (1 << 8)
+#define UC32_PAGETABLE_WRITE (1 << 7)
+#define UC32_PAGETABLE_EXEC (1 << 6)
+#define UC32_PAGETABLE_EXIST (1 << 2)
+#define PAGETABLE_TYPE(x) ((x) & 3)
+
+
+/* Map CPU modes onto saved register banks. */
+static inline int bank_number(int mode)
+{
+ switch (mode) {
+ case ASR_MODE_USER:
+ case ASR_MODE_SUSR:
+ return 0;
+ case ASR_MODE_PRIV:
+ return 1;
+ case ASR_MODE_TRAP:
+ return 2;
+ case ASR_MODE_EXTN:
+ return 3;
+ case ASR_MODE_INTR:
+ return 4;
+ }
+ cpu_abort(cpu_single_env, "Bad mode %x\n", mode);
+ return -1;
+}
+
void switch_mode(CPUUniCore32State *env, int mode)
{
- cpu_abort(env, "%s not supported yet\n", __func__);
+ int old_mode;
+ int i;
+
+ old_mode = env->uncached_asr & ASR_M;
+ if (mode == old_mode) {
+ return;
+ }
+
+ i = bank_number(old_mode);
+ env->banked_r29[i] = env->regs[29];
+ env->banked_r30[i] = env->regs[30];
+ env->banked_bsr[i] = env->bsr;
+
+ i = bank_number(mode);
+ env->regs[29] = env->banked_r29[i];
+ env->regs[30] = env->banked_r30[i];
+ env->bsr = env->banked_bsr[i];
}
+/* Handle a CPU exception. */
void do_interrupt(CPUUniCore32State *env)
{
- cpu_abort(env, "%s not supported yet\n", __func__);
+ uint32_t addr;
+ int new_mode;
+
+ switch (env->exception_index) {
+ case UC32_EXCP_PRIV:
+ new_mode = ASR_MODE_PRIV;
+ addr = 0x08;
+ break;
+ case UC32_EXCP_ITRAP:
+ DPRINTF("itrap happened at %x\n", env->regs[31]);
+ new_mode = ASR_MODE_TRAP;
+ addr = 0x0c;
+ break;
+ case UC32_EXCP_DTRAP:
+ DPRINTF("dtrap happened at %x\n", env->regs[31]);
+ new_mode = ASR_MODE_TRAP;
+ addr = 0x10;
+ break;
+ case UC32_EXCP_INTR:
+ new_mode = ASR_MODE_INTR;
+ addr = 0x18;
+ break;
+ default:
+ cpu_abort(env, "Unhandled exception 0x%x\n", env->exception_index);
+ return;
+ }
+ /* High vectors. */
+ if (env->cp0.c1_sys & (1 << 13)) {
+ addr += 0xffff0000;
+ }
+
+ switch_mode(env, new_mode);
+ env->bsr = cpu_asr_read(env);
+ env->uncached_asr = (env->uncached_asr & ~ASR_M) | new_mode;
+ env->uncached_asr |= ASR_I;
+ /* The PC already points to the proper instruction. */
+ env->regs[30] = env->regs[31];
+ env->regs[31] = addr;
+ env->interrupt_request |= CPU_INTERRUPT_EXITTB;
+}
+
+static int get_phys_addr_ucv2(CPUUniCore32State *env, uint32_t address,
+ int access_type, int is_user, uint32_t *phys_ptr, int *prot,
+ target_ulong *page_size)
+{
+ int code;
+ uint32_t table;
+ uint32_t desc;
+ uint32_t phys_addr;
+
+ /* Pagetable walk. */
+ /* Lookup l1 descriptor. */
+ table = env->cp0.c2_base & 0xfffff000;
+ table |= (address >> 20) & 0xffc;
+ desc = ldl_phys(table);
+ code = 0;
+ switch (PAGETABLE_TYPE(desc)) {
+ case 3:
+ /* Superpage */
+ if (!(desc & UC32_PAGETABLE_EXIST)) {
+ code = 0x0b; /* superpage miss */
+ goto do_fault;
+ }
+ phys_addr = (desc & 0xffc00000) | (address & 0x003fffff);
+ *page_size = SUPERPAGE_SIZE;
+ break;
+ case 0:
+ /* Lookup l2 entry. */
+ if (is_user) {
+ DPRINTF("PGD address %x, desc %x\n", table, desc);
+ }
+ if (!(desc & UC32_PAGETABLE_EXIST)) {
+ code = 0x05; /* second pagetable miss */
+ goto do_fault;
+ }
+ table = (desc & 0xfffff000) | ((address >> 10) & 0xffc);
+ desc = ldl_phys(table);
+ /* 4k page. */
+ if (is_user) {
+ DPRINTF("PTE address %x, desc %x\n", table, desc);
+ }
+ if (!(desc & UC32_PAGETABLE_EXIST)) {
+ code = 0x08; /* page miss */
+ goto do_fault;
+ }
+ switch (PAGETABLE_TYPE(desc)) {
+ case 0:
+ phys_addr = (desc & 0xfffff000) | (address & 0xfff);
+ *page_size = TARGET_PAGE_SIZE;
+ break;
+ default:
+ cpu_abort(env, "wrong page type!");
+ }
+ break;
+ default:
+ cpu_abort(env, "wrong page type!");
+ }
+
+ *phys_ptr = phys_addr;
+ *prot = 0;
+ /* Check access permissions. */
+ if (desc & UC32_PAGETABLE_READ) {
+ *prot |= PAGE_READ;
+ } else {
+ if (is_user && (access_type == 0)) {
+ code = 0x11; /* access unreadable area */
+ goto do_fault;
+ }
+ }
+
+ if (desc & UC32_PAGETABLE_WRITE) {
+ *prot |= PAGE_WRITE;
+ } else {
+ if (is_user && (access_type == 1)) {
+ code = 0x12; /* access unwritable area */
+ goto do_fault;
+ }
+ }
+
+ if (desc & UC32_PAGETABLE_EXEC) {
+ *prot |= PAGE_EXEC;
+ } else {
+ if (is_user && (access_type == 2)) {
+ code = 0x13; /* access unexecutable area */
+ goto do_fault;
+ }
+ }
+
+do_fault:
+ return code;
}
int uc32_cpu_handle_mmu_fault(CPUUniCore32State *env, target_ulong address,
int access_type, int mmu_idx)
{
- cpu_abort(env, "%s not supported yet\n", __func__);
- return 1;
+ uint32_t phys_addr;
+ target_ulong page_size;
+ int prot;
+ int ret, is_user;
+
+ ret = 1;
+ is_user = mmu_idx == MMU_USER_IDX;
+
+ if ((env->cp0.c1_sys & 1) == 0) {
+ /* MMU disabled. */
+ phys_addr = address;
+ prot = PAGE_READ | PAGE_WRITE | PAGE_EXEC;
+ page_size = TARGET_PAGE_SIZE;
+ ret = 0;
+ } else {
+ if ((address & (1 << 31)) || (is_user)) {
+ ret = get_phys_addr_ucv2(env, address, access_type, is_user,
+ &phys_addr, &prot, &page_size);
+ if (is_user) {
+ DPRINTF("user space access: ret %x, address %x, "
+ "access_type %x, phys_addr %x, prot %x\n",
+ ret, address, access_type, phys_addr, prot);
+ }
+ } else {
+ /*IO memory */
+ phys_addr = address | (1 << 31);
+ prot = PAGE_READ | PAGE_WRITE | PAGE_EXEC;
+ page_size = TARGET_PAGE_SIZE;
+ ret = 0;
+ }
+ }
+
+ if (ret == 0) {
+ /* Map a single page. */
+ phys_addr &= TARGET_PAGE_MASK;
+ address &= TARGET_PAGE_MASK;
+ tlb_set_page(env, address, phys_addr, prot, mmu_idx, page_size);
+ return 0;
+ }
+
+ env->cp0.c3_faultstatus = ret;
+ env->cp0.c4_faultaddr = address;
+ if (access_type == 2) {
+ env->exception_index = UC32_EXCP_ITRAP;
+ } else {
+ env->exception_index = UC32_EXCP_DTRAP;
+ }
+ return ret;
}
target_phys_addr_t cpu_get_phys_page_debug(CPUUniCore32State *env,
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 06/19] unicore32-softmmu: Make sure that kernel can access user space
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (4 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 05/19] unicore32-softmmu: Implement softmmu specific functions gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 07/19] unicore32-softmmu: Add puv3 soc/board support gxt
` (13 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
As a matter of course, we need to access user space in kernel code,
so we need to correct load/store decoders to indicate correct memory
region.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
target-unicore32/translate.c | 36 ++++++++++++++++++++++++++----------
1 files changed, 26 insertions(+), 10 deletions(-)
diff --git a/target-unicore32/translate.c b/target-unicore32/translate.c
index e37d5be..5ee3a59 100644
--- a/target-unicore32/translate.c
+++ b/target-unicore32/translate.c
@@ -33,9 +33,16 @@ typedef struct DisasContext {
int condlabel;
struct TranslationBlock *tb;
int singlestep_enabled;
+#ifndef CONFIG_USER_ONLY
+ int user;
+#endif
} DisasContext;
-#define IS_USER(s) 1
+#ifndef CONFIG_USER_ONLY
+#define IS_USER(s) (s->user)
+#else
+#define IS_USER(s) 1
+#endif
/* These instructions trap after executing, so defer them until after the
conditional executions state has been updated. */
@@ -1554,12 +1561,12 @@ static void do_misc(CPUUniCore32State *env, DisasContext *s, uint32_t insn)
/* load/store I_offset and R_offset */
static void do_ldst_ir(CPUUniCore32State *env, DisasContext *s, uint32_t insn)
{
- unsigned int i;
+ unsigned int mmu_idx;
TCGv tmp;
TCGv tmp2;
tmp2 = load_reg(s, UCOP_REG_N);
- i = (IS_USER(s) || (!UCOP_SET_P && UCOP_SET_W));
+ mmu_idx = (IS_USER(s) || (!UCOP_SET_P && UCOP_SET_W));
/* immediate */
if (UCOP_SET_P) {
@@ -1569,17 +1576,17 @@ static void do_ldst_ir(CPUUniCore32State *env, DisasContext *s, uint32_t insn)
if (UCOP_SET_L) {
/* load */
if (UCOP_SET_B) {
- tmp = gen_ld8u(tmp2, i);
+ tmp = gen_ld8u(tmp2, mmu_idx);
} else {
- tmp = gen_ld32(tmp2, i);
+ tmp = gen_ld32(tmp2, mmu_idx);
}
} else {
/* store */
tmp = load_reg(s, UCOP_REG_D);
if (UCOP_SET_B) {
- gen_st8(tmp, tmp2, i);
+ gen_st8(tmp, tmp2, mmu_idx);
} else {
- gen_st32(tmp, tmp2, i);
+ gen_st32(tmp, tmp2, mmu_idx);
}
}
if (!UCOP_SET_P) {
@@ -1682,7 +1689,7 @@ static void do_ldst_hwsb(CPUUniCore32State *env, DisasContext *s, uint32_t insn)
/* load/store multiple words */
static void do_ldst_m(CPUUniCore32State *env, DisasContext *s, uint32_t insn)
{
- unsigned int val, i;
+ unsigned int val, i, mmu_idx;
int j, n, reg, user, loaded_base;
TCGv tmp;
TCGv tmp2;
@@ -1703,6 +1710,7 @@ static void do_ldst_m(CPUUniCore32State *env, DisasContext *s, uint32_t insn)
}
}
+ mmu_idx = (IS_USER(s) || (!UCOP_SET_P && UCOP_SET_W));
addr = load_reg(s, UCOP_REG_N);
/* compute total size */
@@ -1747,7 +1755,7 @@ static void do_ldst_m(CPUUniCore32State *env, DisasContext *s, uint32_t insn)
}
if (UCOP_SET(i)) {
if (UCOP_SET_L) { /* load */
- tmp = gen_ld32(addr, IS_USER(s));
+ tmp = gen_ld32(addr, mmu_idx);
if (reg == 31) {
gen_bx(s, tmp);
} else if (user) {
@@ -1775,7 +1783,7 @@ static void do_ldst_m(CPUUniCore32State *env, DisasContext *s, uint32_t insn)
} else {
tmp = load_reg(s, reg);
}
- gen_st32(tmp, addr, IS_USER(s));
+ gen_st32(tmp, addr, mmu_idx);
}
j++;
/* no need to add after the last transfer */
@@ -1964,6 +1972,14 @@ static inline void gen_intermediate_code_internal(CPUUniCore32State *env,
max_insns = CF_COUNT_MASK;
}
+#ifndef CONFIG_USER_ONLY
+ if ((env->uncached_asr & ASR_M) == ASR_MODE_USER) {
+ dc->user = 1;
+ } else {
+ dc->user = 0;
+ }
+#endif
+
gen_icount_start();
do {
if (unlikely(!QTAILQ_EMPTY(&env->breakpoints))) {
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 07/19] unicore32-softmmu: Add puv3 soc/board support
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (5 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 06/19] unicore32-softmmu: Make sure that kernel can access user space gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 08/19] unicore32-softmmu: Add puv3 interrupt support gxt
` (12 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch only add puv3 soc/board support, which introduces puv3
machine description, and specifies console type.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
default-configs/unicore32-softmmu.mak | 1 +
hw/puv3.c | 93 +++++++++++++++++++++++++++++++++
hw/puv3.h | 49 +++++++++++++++++
hw/unicore32/Makefile.objs | 5 ++
4 files changed, 148 insertions(+), 0 deletions(-)
create mode 100644 hw/puv3.c
create mode 100644 hw/puv3.h
diff --git a/default-configs/unicore32-softmmu.mak b/default-configs/unicore32-softmmu.mak
index 5f04fe3..726a338 100644
--- a/default-configs/unicore32-softmmu.mak
+++ b/default-configs/unicore32-softmmu.mak
@@ -1 +1,2 @@
# Default configuration for unicore32-softmmu
+CONFIG_PUV3=y
diff --git a/hw/puv3.c b/hw/puv3.c
new file mode 100644
index 0000000..0dc129d
--- /dev/null
+++ b/hw/puv3.c
@@ -0,0 +1,93 @@
+/*
+ * Generic PKUnity SoC machine and board descriptor
+ *
+ * Copyright (C) 2010-2012 Guan Xuetao
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation, or any later version.
+ * See the COPYING file in the top-level directory.
+ */
+#include "console.h"
+#include "elf.h"
+#include "exec-memory.h"
+#include "sysbus.h"
+#include "boards.h"
+#include "loader.h"
+#include "pc.h"
+
+#undef DEBUG_PUV3
+#include "puv3.h"
+
+#define KERNEL_LOAD_ADDR 0x03000000
+#define KERNEL_MAX_SIZE 0x00800000 /* Just a guess */
+
+static void puv3_soc_init(CPUUniCore32State *env)
+{
+ /* TODO */
+}
+
+static void puv3_board_init(CPUUniCore32State *env, ram_addr_t ram_size)
+{
+ MemoryRegion *ram_memory = g_new(MemoryRegion, 1);
+
+ /* SDRAM at address zero. */
+ memory_region_init_ram(ram_memory, "puv3.ram", ram_size);
+ vmstate_register_ram_global(ram_memory);
+ memory_region_add_subregion(get_system_memory(), 0, ram_memory);
+}
+
+static void puv3_load_kernel(const char *kernel_filename)
+{
+ int size;
+
+ assert(kernel_filename != NULL);
+
+ /* only zImage format supported */
+ size = load_image_targphys(kernel_filename, KERNEL_LOAD_ADDR,
+ KERNEL_MAX_SIZE);
+ if (size < 0) {
+ hw_error("Load kernel error: '%s'\n", kernel_filename);
+ }
+
+ /* cheat curses that we have a graphic console, only under ocd console */
+ graphic_console_init(NULL, NULL, NULL, NULL, NULL);
+}
+
+static void puv3_init(ram_addr_t ram_size, const char *boot_device,
+ const char *kernel_filename, const char *kernel_cmdline,
+ const char *initrd_filename, const char *cpu_model)
+{
+ CPUUniCore32State *env;
+
+ if (initrd_filename) {
+ hw_error("Please use kernel built-in initramdisk.\n");
+ }
+
+ if (!cpu_model) {
+ cpu_model = "UniCore-II";
+ }
+
+ env = cpu_init(cpu_model);
+ if (!env) {
+ hw_error("Unable to find CPU definition\n");
+ }
+
+ puv3_soc_init(env);
+ puv3_board_init(env, ram_size);
+ puv3_load_kernel(kernel_filename);
+}
+
+static QEMUMachine puv3_machine = {
+ .name = "puv3",
+ .desc = "PKUnity Version-3 based on UniCore32",
+ .init = puv3_init,
+ .use_scsi = 0,
+};
+
+static void puv3_machine_init(void)
+{
+ qemu_register_machine(&puv3_machine);
+}
+
+machine_init(puv3_machine_init)
diff --git a/hw/puv3.h b/hw/puv3.h
new file mode 100644
index 0000000..f37adcb
--- /dev/null
+++ b/hw/puv3.h
@@ -0,0 +1,49 @@
+/*
+ * Misc PKUnity SoC declarations
+ *
+ * Copyright (C) 2010-2012 Guan Xuetao
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation, or any later version.
+ * See the COPYING file in the top-level directory.
+ */
+#ifndef QEMU_HW_PUV3_H
+#define QEMU_HW_PUV3_H
+
+#define PUV3_REGS_OFFSET (0x1000) /* 4K is reasonable */
+
+/* PKUnity System bus (AHB): 0xc0000000 - 0xedffffff (640MB) */
+#define PUV3_DMA_BASE (0xc0200000) /* AHB-4 */
+
+/* PKUnity Peripheral bus (APB): 0xee000000 - 0xefffffff (128MB) */
+#define PUV3_GPIO_BASE (0xee500000) /* APB-5 */
+#define PUV3_INTC_BASE (0xee600000) /* APB-6 */
+#define PUV3_OST_BASE (0xee800000) /* APB-8 */
+#define PUV3_PM_BASE (0xeea00000) /* APB-10 */
+#define PUV3_PS2_BASE (0xeeb00000) /* APB-11 */
+
+/* Hardware interrupts */
+#define PUV3_IRQS_NR (32)
+
+#define PUV3_IRQS_GPIOLOW0 (0)
+#define PUV3_IRQS_GPIOLOW1 (1)
+#define PUV3_IRQS_GPIOLOW2 (2)
+#define PUV3_IRQS_GPIOLOW3 (3)
+#define PUV3_IRQS_GPIOLOW4 (4)
+#define PUV3_IRQS_GPIOLOW5 (5)
+#define PUV3_IRQS_GPIOLOW6 (6)
+#define PUV3_IRQS_GPIOLOW7 (7)
+#define PUV3_IRQS_GPIOHIGH (8)
+#define PUV3_IRQS_PS2_KBD (22)
+#define PUV3_IRQS_PS2_AUX (23)
+#define PUV3_IRQS_OST0 (26)
+
+/* All puv3_*.c use DPRINTF for debug. */
+#ifdef DEBUG_PUV3
+#define DPRINTF(fmt, ...) printf("%s: " fmt , __func__, ## __VA_ARGS__)
+#else
+#define DPRINTF(fmt, ...) do {} while (0)
+#endif
+
+#endif /* !QEMU_HW_PUV3_H */
diff --git a/hw/unicore32/Makefile.objs b/hw/unicore32/Makefile.objs
index b6a3383..0725ce3 100644
--- a/hw/unicore32/Makefile.objs
+++ b/hw/unicore32/Makefile.objs
@@ -1 +1,6 @@
# For UniCore32 machines and boards
+
+# PKUnity-v3 SoC and board information
+obj-${CONFIG_PUV3} += puv3.o
+
+obj-y := $(addprefix ../,$(obj-y))
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 08/19] unicore32-softmmu: Add puv3 interrupt support
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (6 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 07/19] unicore32-softmmu: Add puv3 soc/board support gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 09/19] unicore32-softmmu: Add puv3 ostimer support gxt
` (11 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch adds puv3 interrupt support, include interrupt controler
device simulation and interrupt handler in puv3 machine.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
hw/Makefile.objs | 3 +
hw/puv3.c | 23 +++++++++-
hw/puv3_intc.c | 135 ++++++++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 160 insertions(+), 1 deletions(-)
create mode 100644 hw/puv3_intc.c
diff --git a/hw/Makefile.objs b/hw/Makefile.objs
index 8327e55..50554b6 100644
--- a/hw/Makefile.objs
+++ b/hw/Makefile.objs
@@ -66,6 +66,9 @@ hw-obj-$(CONFIG_XILINX) += xilinx_uartlite.o
hw-obj-$(CONFIG_XILINX_AXI) += xilinx_axidma.o
hw-obj-$(CONFIG_XILINX_AXI) += xilinx_axienet.o
+# PKUnity SoC devices
+hw-obj-$(CONFIG_PUV3) += puv3_intc.o
+
# PCI watchdog devices
hw-obj-$(CONFIG_PCI) += wdt_i6300esb.o
diff --git a/hw/puv3.c b/hw/puv3.c
index 0dc129d..2870455 100644
--- a/hw/puv3.c
+++ b/hw/puv3.c
@@ -22,9 +22,30 @@
#define KERNEL_LOAD_ADDR 0x03000000
#define KERNEL_MAX_SIZE 0x00800000 /* Just a guess */
+static void puv3_intc_cpu_handler(void *opaque, int irq, int level)
+{
+ CPUUniCore32State *env = opaque;
+
+ assert(irq == 0);
+ if (level) {
+ cpu_interrupt(env, CPU_INTERRUPT_HARD);
+ } else {
+ cpu_reset_interrupt(env, CPU_INTERRUPT_HARD);
+ }
+}
+
static void puv3_soc_init(CPUUniCore32State *env)
{
- /* TODO */
+ qemu_irq *cpu_intc, irqs[PUV3_IRQS_NR];
+ DeviceState *dev;
+ int i;
+
+ /* Initialize interrupt controller */
+ cpu_intc = qemu_allocate_irqs(puv3_intc_cpu_handler, env, 1);
+ dev = sysbus_create_simple("puv3_intc", PUV3_INTC_BASE, *cpu_intc);
+ for (i = 0; i < PUV3_IRQS_NR; i++) {
+ irqs[i] = qdev_get_gpio_in(dev, i);
+ }
}
static void puv3_board_init(CPUUniCore32State *env, ram_addr_t ram_size)
diff --git a/hw/puv3_intc.c b/hw/puv3_intc.c
new file mode 100644
index 0000000..9e0b975
--- /dev/null
+++ b/hw/puv3_intc.c
@@ -0,0 +1,135 @@
+/*
+ * INTC device simulation in PKUnity SoC
+ *
+ * Copyright (C) 2010-2012 Guan Xuetao
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation, or any later version.
+ * See the COPYING file in the top-level directory.
+ */
+#include "sysbus.h"
+
+#undef DEBUG_PUV3
+#include "puv3.h"
+
+typedef struct {
+ SysBusDevice busdev;
+ MemoryRegion iomem;
+ qemu_irq parent_irq;
+
+ uint32_t reg_ICMR;
+ uint32_t reg_ICPR;
+} PUV3INTCState;
+
+/* Update interrupt status after enabled or pending bits have been changed. */
+static void puv3_intc_update(PUV3INTCState *s)
+{
+ if (s->reg_ICMR & s->reg_ICPR) {
+ qemu_irq_raise(s->parent_irq);
+ } else {
+ qemu_irq_lower(s->parent_irq);
+ }
+}
+
+/* Process a change in an external INTC input. */
+static void puv3_intc_handler(void *opaque, int irq, int level)
+{
+ PUV3INTCState *s = opaque;
+
+ DPRINTF("irq 0x%x, level 0x%x\n", irq, level);
+ if (level) {
+ s->reg_ICPR |= (1 << irq);
+ } else {
+ s->reg_ICPR &= ~(1 << irq);
+ }
+ puv3_intc_update(s);
+}
+
+static uint64_t puv3_intc_read(void *opaque, target_phys_addr_t offset,
+ unsigned size)
+{
+ PUV3INTCState *s = opaque;
+ uint32_t ret = 0;
+
+ switch (offset) {
+ case 0x04: /* INTC_ICMR */
+ ret = s->reg_ICMR;
+ break;
+ case 0x0c: /* INTC_ICIP */
+ ret = s->reg_ICPR; /* the same value with ICPR */
+ break;
+ default:
+ DPRINTF("Bad offset %x\n", (int)offset);
+ }
+ DPRINTF("offset 0x%x, value 0x%x\n", offset, ret);
+ return ret;
+}
+
+static void puv3_intc_write(void *opaque, target_phys_addr_t offset,
+ uint64_t value, unsigned size)
+{
+ PUV3INTCState *s = opaque;
+
+ DPRINTF("offset 0x%x, value 0x%x\n", offset, value);
+ switch (offset) {
+ case 0x00: /* INTC_ICLR */
+ case 0x14: /* INTC_ICCR */
+ break;
+ case 0x04: /* INTC_ICMR */
+ s->reg_ICMR = value;
+ break;
+ default:
+ DPRINTF("Bad offset 0x%x\n", (int)offset);
+ return;
+ }
+ puv3_intc_update(s);
+}
+
+static const MemoryRegionOps puv3_intc_ops = {
+ .read = puv3_intc_read,
+ .write = puv3_intc_write,
+ .impl = {
+ .min_access_size = 4,
+ .max_access_size = 4,
+ },
+ .endianness = DEVICE_NATIVE_ENDIAN,
+};
+
+static int puv3_intc_init(SysBusDevice *dev)
+{
+ PUV3INTCState *s = FROM_SYSBUS(PUV3INTCState, dev);
+
+ qdev_init_gpio_in(&s->busdev.qdev, puv3_intc_handler, PUV3_IRQS_NR);
+ sysbus_init_irq(&s->busdev, &s->parent_irq);
+
+ s->reg_ICMR = 0;
+ s->reg_ICPR = 0;
+
+ memory_region_init_io(&s->iomem, &puv3_intc_ops, s, "puv3_intc",
+ PUV3_REGS_OFFSET);
+ sysbus_init_mmio(dev, &s->iomem);
+
+ return 0;
+}
+
+static void puv3_intc_class_init(ObjectClass *klass, void *data)
+{
+ SysBusDeviceClass *sdc = SYS_BUS_DEVICE_CLASS(klass);
+
+ sdc->init = puv3_intc_init;
+}
+
+static const TypeInfo puv3_intc_info = {
+ .name = "puv3_intc",
+ .parent = TYPE_SYS_BUS_DEVICE,
+ .instance_size = sizeof(PUV3INTCState),
+ .class_init = puv3_intc_class_init,
+};
+
+static void puv3_intc_register_type(void)
+{
+ type_register_static(&puv3_intc_info);
+}
+
+type_init(puv3_intc_register_type)
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 09/19] unicore32-softmmu: Add puv3 ostimer support
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (7 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 08/19] unicore32-softmmu: Add puv3 interrupt support gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 10/19] unicore32-softmmu: Add puv3 gpio support gxt
` (10 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch adds puv3 ostimer support, include os timer
device simulation and ptimer support in puv3 machine.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
default-configs/unicore32-softmmu.mak | 1 +
hw/Makefile.objs | 1 +
hw/puv3.c | 3 +
hw/puv3_ost.c | 151 +++++++++++++++++++++++++++++++++
4 files changed, 156 insertions(+), 0 deletions(-)
create mode 100644 hw/puv3_ost.c
diff --git a/default-configs/unicore32-softmmu.mak b/default-configs/unicore32-softmmu.mak
index 726a338..4d4fbfc 100644
--- a/default-configs/unicore32-softmmu.mak
+++ b/default-configs/unicore32-softmmu.mak
@@ -1,2 +1,3 @@
# Default configuration for unicore32-softmmu
CONFIG_PUV3=y
+CONFIG_PTIMER=y
diff --git a/hw/Makefile.objs b/hw/Makefile.objs
index 50554b6..b96722a 100644
--- a/hw/Makefile.objs
+++ b/hw/Makefile.objs
@@ -68,6 +68,7 @@ hw-obj-$(CONFIG_XILINX_AXI) += xilinx_axienet.o
# PKUnity SoC devices
hw-obj-$(CONFIG_PUV3) += puv3_intc.o
+hw-obj-$(CONFIG_PUV3) += puv3_ost.o
# PCI watchdog devices
hw-obj-$(CONFIG_PCI) += wdt_i6300esb.o
diff --git a/hw/puv3.c b/hw/puv3.c
index 2870455..5a8a27c 100644
--- a/hw/puv3.c
+++ b/hw/puv3.c
@@ -46,6 +46,9 @@ static void puv3_soc_init(CPUUniCore32State *env)
for (i = 0; i < PUV3_IRQS_NR; i++) {
irqs[i] = qdev_get_gpio_in(dev, i);
}
+
+ /* Initialize minimal necessary devices for kernel booting */
+ sysbus_create_simple("puv3_ost", PUV3_OST_BASE, irqs[PUV3_IRQS_OST0]);
}
static void puv3_board_init(CPUUniCore32State *env, ram_addr_t ram_size)
diff --git a/hw/puv3_ost.c b/hw/puv3_ost.c
new file mode 100644
index 0000000..dd30cad
--- /dev/null
+++ b/hw/puv3_ost.c
@@ -0,0 +1,151 @@
+/*
+ * OSTimer device simulation in PKUnity SoC
+ *
+ * Copyright (C) 2010-2012 Guan Xuetao
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation, or any later version.
+ * See the COPYING file in the top-level directory.
+ */
+#include "sysbus.h"
+#include "ptimer.h"
+
+#undef DEBUG_PUV3
+#include "puv3.h"
+
+/* puv3 ostimer implementation. */
+typedef struct {
+ SysBusDevice busdev;
+ MemoryRegion iomem;
+ QEMUBH *bh;
+ qemu_irq irq;
+ ptimer_state *ptimer;
+
+ uint32_t reg_OSMR0;
+ uint32_t reg_OSCR;
+ uint32_t reg_OSSR;
+ uint32_t reg_OIER;
+} PUV3OSTState;
+
+static uint64_t puv3_ost_read(void *opaque, target_phys_addr_t offset,
+ unsigned size)
+{
+ PUV3OSTState *s = opaque;
+ uint32_t ret = 0;
+
+ switch (offset) {
+ case 0x10: /* Counter Register */
+ ret = s->reg_OSMR0 - (uint32_t)ptimer_get_count(s->ptimer);
+ break;
+ case 0x14: /* Status Register */
+ ret = s->reg_OSSR;
+ break;
+ case 0x1c: /* Interrupt Enable Register */
+ ret = s->reg_OIER;
+ break;
+ default:
+ DPRINTF("Bad offset %x\n", (int)offset);
+ }
+ DPRINTF("offset 0x%x, value 0x%x\n", offset, ret);
+ return ret;
+}
+
+static void puv3_ost_write(void *opaque, target_phys_addr_t offset,
+ uint64_t value, unsigned size)
+{
+ PUV3OSTState *s = opaque;
+
+ DPRINTF("offset 0x%x, value 0x%x\n", offset, value);
+ switch (offset) {
+ case 0x00: /* Match Register 0 */
+ s->reg_OSMR0 = value;
+ if (s->reg_OSMR0 > s->reg_OSCR) {
+ ptimer_set_count(s->ptimer, s->reg_OSMR0 - s->reg_OSCR);
+ } else {
+ ptimer_set_count(s->ptimer, s->reg_OSMR0 +
+ (0xffffffff - s->reg_OSCR));
+ }
+ ptimer_run(s->ptimer, 2);
+ break;
+ case 0x14: /* Status Register */
+ assert(value == 0);
+ if (s->reg_OSSR) {
+ s->reg_OSSR = value;
+ qemu_irq_lower(s->irq);
+ }
+ break;
+ case 0x1c: /* Interrupt Enable Register */
+ s->reg_OIER = value;
+ break;
+ default:
+ DPRINTF("Bad offset %x\n", (int)offset);
+ }
+}
+
+static const MemoryRegionOps puv3_ost_ops = {
+ .read = puv3_ost_read,
+ .write = puv3_ost_write,
+ .impl = {
+ .min_access_size = 4,
+ .max_access_size = 4,
+ },
+ .endianness = DEVICE_NATIVE_ENDIAN,
+};
+
+static void puv3_ost_tick(void *opaque)
+{
+ PUV3OSTState *s = opaque;
+
+ DPRINTF("ost hit when ptimer counter from 0x%x to 0x%x!\n",
+ s->reg_OSCR, s->reg_OSMR0);
+
+ s->reg_OSCR = s->reg_OSMR0;
+ if (s->reg_OIER) {
+ s->reg_OSSR = 1;
+ qemu_irq_raise(s->irq);
+ }
+}
+
+static int puv3_ost_init(SysBusDevice *dev)
+{
+ PUV3OSTState *s = FROM_SYSBUS(PUV3OSTState, dev);
+
+ s->reg_OIER = 0;
+ s->reg_OSSR = 0;
+ s->reg_OSMR0 = 0;
+ s->reg_OSCR = 0;
+
+ sysbus_init_irq(dev, &s->irq);
+
+ s->bh = qemu_bh_new(puv3_ost_tick, s);
+ s->ptimer = ptimer_init(s->bh);
+ ptimer_set_freq(s->ptimer, 50 * 1000 * 1000);
+
+ memory_region_init_io(&s->iomem, &puv3_ost_ops, s, "puv3_ost",
+ PUV3_REGS_OFFSET);
+ sysbus_init_mmio(dev, &s->iomem);
+
+ return 0;
+}
+
+static void puv3_ost_class_init(ObjectClass *klass, void *data)
+{
+ SysBusDeviceClass *sdc = SYS_BUS_DEVICE_CLASS(klass);
+
+ sdc->init = puv3_ost_init;
+}
+
+static const TypeInfo puv3_ost_info = {
+ .name = "puv3_ost",
+ .parent = TYPE_SYS_BUS_DEVICE,
+ .instance_size = sizeof(PUV3OSTState),
+ .class_init = puv3_ost_class_init,
+};
+
+static void puv3_ost_register_type(void)
+{
+ type_register_static(&puv3_ost_info);
+}
+
+type_init(puv3_ost_register_type)
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 10/19] unicore32-softmmu: Add puv3 gpio support
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (8 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 09/19] unicore32-softmmu: Add puv3 ostimer support gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 11/19] unicore32-softmmu: Add puv3 pm support gxt
` (9 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch adds puv3 gpio (General Purpose Input/Output) support,
include gpio device simulation and its interrupt support.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
hw/Makefile.objs | 1 +
hw/puv3.c | 6 ++
hw/puv3_gpio.c | 141 ++++++++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 148 insertions(+), 0 deletions(-)
create mode 100644 hw/puv3_gpio.c
diff --git a/hw/Makefile.objs b/hw/Makefile.objs
index b96722a..c6cc97b 100644
--- a/hw/Makefile.objs
+++ b/hw/Makefile.objs
@@ -69,6 +69,7 @@ hw-obj-$(CONFIG_XILINX_AXI) += xilinx_axienet.o
# PKUnity SoC devices
hw-obj-$(CONFIG_PUV3) += puv3_intc.o
hw-obj-$(CONFIG_PUV3) += puv3_ost.o
+hw-obj-$(CONFIG_PUV3) += puv3_gpio.o
# PCI watchdog devices
hw-obj-$(CONFIG_PCI) += wdt_i6300esb.o
diff --git a/hw/puv3.c b/hw/puv3.c
index 5a8a27c..0354cf6 100644
--- a/hw/puv3.c
+++ b/hw/puv3.c
@@ -49,6 +49,12 @@ static void puv3_soc_init(CPUUniCore32State *env)
/* Initialize minimal necessary devices for kernel booting */
sysbus_create_simple("puv3_ost", PUV3_OST_BASE, irqs[PUV3_IRQS_OST0]);
+ sysbus_create_varargs("puv3_gpio", PUV3_GPIO_BASE,
+ irqs[PUV3_IRQS_GPIOLOW0], irqs[PUV3_IRQS_GPIOLOW1],
+ irqs[PUV3_IRQS_GPIOLOW2], irqs[PUV3_IRQS_GPIOLOW3],
+ irqs[PUV3_IRQS_GPIOLOW4], irqs[PUV3_IRQS_GPIOLOW5],
+ irqs[PUV3_IRQS_GPIOLOW6], irqs[PUV3_IRQS_GPIOLOW7],
+ irqs[PUV3_IRQS_GPIOHIGH], NULL);
}
static void puv3_board_init(CPUUniCore32State *env, ram_addr_t ram_size)
diff --git a/hw/puv3_gpio.c b/hw/puv3_gpio.c
new file mode 100644
index 0000000..d78aac3
--- /dev/null
+++ b/hw/puv3_gpio.c
@@ -0,0 +1,141 @@
+/*
+ * GPIO device simulation in PKUnity SoC
+ *
+ * Copyright (C) 2010-2012 Guan Xuetao
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation, or any later version.
+ * See the COPYING file in the top-level directory.
+ */
+#include "hw.h"
+#include "sysbus.h"
+
+#undef DEBUG_PUV3
+#include "puv3.h"
+
+typedef struct {
+ SysBusDevice busdev;
+ MemoryRegion iomem;
+ qemu_irq irq[9];
+
+ uint32_t reg_GPLR;
+ uint32_t reg_GPDR;
+ uint32_t reg_GPIR;
+} PUV3GPIOState;
+
+static uint64_t puv3_gpio_read(void *opaque, target_phys_addr_t offset,
+ unsigned size)
+{
+ PUV3GPIOState *s = opaque;
+ uint32_t ret;
+
+ switch (offset) {
+ case 0x00:
+ ret = s->reg_GPLR;
+ break;
+ case 0x04:
+ ret = s->reg_GPDR;
+ break;
+ case 0x20:
+ ret = s->reg_GPIR;
+ break;
+ default:
+ DPRINTF("Bad offset 0x%x\n", offset);
+ }
+ DPRINTF("offset 0x%x, value 0x%x\n", offset, ret);
+
+ return ret;
+}
+
+static void puv3_gpio_write(void *opaque, target_phys_addr_t offset,
+ uint64_t value, unsigned size)
+{
+ PUV3GPIOState *s = opaque;
+
+ DPRINTF("offset 0x%x, value 0x%x\n", offset, value);
+ switch (offset) {
+ case 0x04:
+ s->reg_GPDR = value;
+ break;
+ case 0x08:
+ if (s->reg_GPDR & value) {
+ s->reg_GPLR |= value;
+ } else {
+ DPRINTF("Write gpio input port error!");
+ }
+ break;
+ case 0x0c:
+ if (s->reg_GPDR & value) {
+ s->reg_GPLR &= ~value;
+ } else {
+ DPRINTF("Write gpio input port error!");
+ }
+ break;
+ case 0x10: /* GRER */
+ case 0x14: /* GFER */
+ case 0x18: /* GEDR */
+ break;
+ case 0x20: /* GPIR */
+ s->reg_GPIR = value;
+ break;
+ default:
+ DPRINTF("Bad offset 0x%x\n", offset);
+ }
+}
+
+static const MemoryRegionOps puv3_gpio_ops = {
+ .read = puv3_gpio_read,
+ .write = puv3_gpio_write,
+ .impl = {
+ .min_access_size = 4,
+ .max_access_size = 4,
+ },
+ .endianness = DEVICE_NATIVE_ENDIAN,
+};
+
+static int puv3_gpio_init(SysBusDevice *dev)
+{
+ PUV3GPIOState *s = FROM_SYSBUS(PUV3GPIOState, dev);
+
+ s->reg_GPLR = 0;
+ s->reg_GPDR = 0;
+
+ /* FIXME: these irqs not handled yet */
+ sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW0]);
+ sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW1]);
+ sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW2]);
+ sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW3]);
+ sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW4]);
+ sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW5]);
+ sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW6]);
+ sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOLOW7]);
+ sysbus_init_irq(dev, &s->irq[PUV3_IRQS_GPIOHIGH]);
+
+ memory_region_init_io(&s->iomem, &puv3_gpio_ops, s, "puv3_gpio",
+ PUV3_REGS_OFFSET);
+ sysbus_init_mmio(dev, &s->iomem);
+
+ return 0;
+}
+
+static void puv3_gpio_class_init(ObjectClass *klass, void *data)
+{
+ SysBusDeviceClass *sdc = SYS_BUS_DEVICE_CLASS(klass);
+
+ sdc->init = puv3_gpio_init;
+}
+
+static const TypeInfo puv3_gpio_info = {
+ .name = "puv3_gpio",
+ .parent = TYPE_SYS_BUS_DEVICE,
+ .instance_size = sizeof(PUV3GPIOState),
+ .class_init = puv3_gpio_class_init,
+};
+
+static void puv3_gpio_register_type(void)
+{
+ type_register_static(&puv3_gpio_info);
+}
+
+type_init(puv3_gpio_register_type)
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 11/19] unicore32-softmmu: Add puv3 pm support
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (9 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 10/19] unicore32-softmmu: Add puv3 gpio support gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 12/19] unicore32-softmmu: Add puv3 dma support gxt
` (8 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch adds puv3 pm (power management) support,
include pm device simulation for kernel booting.
Thank Blue Swirl for pointing out the missing "break".
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
hw/Makefile.objs | 1 +
hw/puv3.c | 1 +
hw/puv3_pm.c | 149 ++++++++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 151 insertions(+), 0 deletions(-)
create mode 100644 hw/puv3_pm.c
diff --git a/hw/Makefile.objs b/hw/Makefile.objs
index c6cc97b..e2a39d6 100644
--- a/hw/Makefile.objs
+++ b/hw/Makefile.objs
@@ -70,6 +70,7 @@ hw-obj-$(CONFIG_XILINX_AXI) += xilinx_axienet.o
hw-obj-$(CONFIG_PUV3) += puv3_intc.o
hw-obj-$(CONFIG_PUV3) += puv3_ost.o
hw-obj-$(CONFIG_PUV3) += puv3_gpio.o
+hw-obj-$(CONFIG_PUV3) += puv3_pm.o
# PCI watchdog devices
hw-obj-$(CONFIG_PCI) += wdt_i6300esb.o
diff --git a/hw/puv3.c b/hw/puv3.c
index 0354cf6..3a14b27 100644
--- a/hw/puv3.c
+++ b/hw/puv3.c
@@ -48,6 +48,7 @@ static void puv3_soc_init(CPUUniCore32State *env)
}
/* Initialize minimal necessary devices for kernel booting */
+ sysbus_create_simple("puv3_pm", PUV3_PM_BASE, NULL);
sysbus_create_simple("puv3_ost", PUV3_OST_BASE, irqs[PUV3_IRQS_OST0]);
sysbus_create_varargs("puv3_gpio", PUV3_GPIO_BASE,
irqs[PUV3_IRQS_GPIOLOW0], irqs[PUV3_IRQS_GPIOLOW1],
diff --git a/hw/puv3_pm.c b/hw/puv3_pm.c
new file mode 100644
index 0000000..b66fdbe
--- /dev/null
+++ b/hw/puv3_pm.c
@@ -0,0 +1,149 @@
+/*
+ * Power Management device simulation in PKUnity SoC
+ *
+ * Copyright (C) 2010-2012 Guan Xuetao
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation, or any later version.
+ * See the COPYING file in the top-level directory.
+ */
+#include "hw.h"
+#include "sysbus.h"
+
+#undef DEBUG_PUV3
+#include "puv3.h"
+
+typedef struct {
+ SysBusDevice busdev;
+ MemoryRegion iomem;
+
+ uint32_t reg_PMCR;
+ uint32_t reg_PCGR;
+ uint32_t reg_PLL_SYS_CFG;
+ uint32_t reg_PLL_DDR_CFG;
+ uint32_t reg_PLL_VGA_CFG;
+ uint32_t reg_DIVCFG;
+} PUV3PMState;
+
+static uint64_t puv3_pm_read(void *opaque, target_phys_addr_t offset,
+ unsigned size)
+{
+ PUV3PMState *s = opaque;
+ uint32_t ret;
+
+ switch (offset) {
+ case 0x14:
+ ret = s->reg_PCGR;
+ break;
+ case 0x18:
+ ret = s->reg_PLL_SYS_CFG;
+ break;
+ case 0x1c:
+ ret = s->reg_PLL_DDR_CFG;
+ break;
+ case 0x20:
+ ret = s->reg_PLL_VGA_CFG;
+ break;
+ case 0x24:
+ ret = s->reg_DIVCFG;
+ break;
+ case 0x28: /* PLL SYS STATUS */
+ ret = 0x00002401;
+ break;
+ case 0x2c: /* PLL DDR STATUS */
+ ret = 0x00100c00;
+ break;
+ case 0x30: /* PLL VGA STATUS */
+ ret = 0x00003801;
+ break;
+ case 0x34: /* DIV STATUS */
+ ret = 0x22f52015;
+ break;
+ case 0x38: /* SW RESET */
+ ret = 0x0;
+ break;
+ case 0x44: /* PLL DFC DONE */
+ ret = 0x7;
+ break;
+ default:
+ DPRINTF("Bad offset 0x%x\n", offset);
+ }
+ DPRINTF("offset 0x%x, value 0x%x\n", offset, ret);
+
+ return ret;
+}
+
+static void puv3_pm_write(void *opaque, target_phys_addr_t offset,
+ uint64_t value, unsigned size)
+{
+ PUV3PMState *s = opaque;
+
+ switch (offset) {
+ case 0x0:
+ s->reg_PMCR = value;
+ break;
+ case 0x14:
+ s->reg_PCGR = value;
+ break;
+ case 0x18:
+ s->reg_PLL_SYS_CFG = value;
+ break;
+ case 0x1c:
+ s->reg_PLL_DDR_CFG = value;
+ break;
+ case 0x20:
+ s->reg_PLL_VGA_CFG = value;
+ break;
+ case 0x24:
+ case 0x38:
+ break;
+ default:
+ DPRINTF("Bad offset 0x%x\n", offset);
+ }
+ DPRINTF("offset 0x%x, value 0x%x\n", offset, value);
+}
+
+static const MemoryRegionOps puv3_pm_ops = {
+ .read = puv3_pm_read,
+ .write = puv3_pm_write,
+ .impl = {
+ .min_access_size = 4,
+ .max_access_size = 4,
+ },
+ .endianness = DEVICE_NATIVE_ENDIAN,
+};
+
+static int puv3_pm_init(SysBusDevice *dev)
+{
+ PUV3PMState *s = FROM_SYSBUS(PUV3PMState, dev);
+
+ s->reg_PCGR = 0x0;
+
+ memory_region_init_io(&s->iomem, &puv3_pm_ops, s, "puv3_pm",
+ PUV3_REGS_OFFSET);
+ sysbus_init_mmio(dev, &s->iomem);
+
+ return 0;
+}
+
+static void puv3_pm_class_init(ObjectClass *klass, void *data)
+{
+ SysBusDeviceClass *sdc = SYS_BUS_DEVICE_CLASS(klass);
+
+ sdc->init = puv3_pm_init;
+}
+
+static const TypeInfo puv3_pm_info = {
+ .name = "puv3_pm",
+ .parent = TYPE_SYS_BUS_DEVICE,
+ .instance_size = sizeof(PUV3PMState),
+ .class_init = puv3_pm_class_init,
+};
+
+static void puv3_pm_register_type(void)
+{
+ type_register_static(&puv3_pm_info);
+}
+
+type_init(puv3_pm_register_type)
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 12/19] unicore32-softmmu: Add puv3 dma support
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (10 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 11/19] unicore32-softmmu: Add puv3 pm support gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 13/19] unicore32-softmmu: Add ps2 support gxt
` (7 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch adds puv3 dma (Direct Memory Access) support,
include dma device simulation for kernel booting.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
hw/Makefile.objs | 1 +
hw/puv3.c | 1 +
hw/puv3_dma.c | 109 ++++++++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 111 insertions(+), 0 deletions(-)
create mode 100644 hw/puv3_dma.c
diff --git a/hw/Makefile.objs b/hw/Makefile.objs
index e2a39d6..6df346a 100644
--- a/hw/Makefile.objs
+++ b/hw/Makefile.objs
@@ -71,6 +71,7 @@ hw-obj-$(CONFIG_PUV3) += puv3_intc.o
hw-obj-$(CONFIG_PUV3) += puv3_ost.o
hw-obj-$(CONFIG_PUV3) += puv3_gpio.o
hw-obj-$(CONFIG_PUV3) += puv3_pm.o
+hw-obj-$(CONFIG_PUV3) += puv3_dma.o
# PCI watchdog devices
hw-obj-$(CONFIG_PCI) += wdt_i6300esb.o
diff --git a/hw/puv3.c b/hw/puv3.c
index 3a14b27..9acfc5a 100644
--- a/hw/puv3.c
+++ b/hw/puv3.c
@@ -49,6 +49,7 @@ static void puv3_soc_init(CPUUniCore32State *env)
/* Initialize minimal necessary devices for kernel booting */
sysbus_create_simple("puv3_pm", PUV3_PM_BASE, NULL);
+ sysbus_create_simple("puv3_dma", PUV3_DMA_BASE, NULL);
sysbus_create_simple("puv3_ost", PUV3_OST_BASE, irqs[PUV3_IRQS_OST0]);
sysbus_create_varargs("puv3_gpio", PUV3_GPIO_BASE,
irqs[PUV3_IRQS_GPIOLOW0], irqs[PUV3_IRQS_GPIOLOW1],
diff --git a/hw/puv3_dma.c b/hw/puv3_dma.c
new file mode 100644
index 0000000..bd1f43e
--- /dev/null
+++ b/hw/puv3_dma.c
@@ -0,0 +1,109 @@
+/*
+ * DMA device simulation in PKUnity SoC
+ *
+ * Copyright (C) 2010-2012 Guan Xuetao
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation, or any later version.
+ * See the COPYING file in the top-level directory.
+ */
+#include "hw.h"
+#include "sysbus.h"
+
+#undef DEBUG_PUV3
+#include "puv3.h"
+
+#define PUV3_DMA_CH_NR (6)
+#define PUV3_DMA_CH_MASK (0xff)
+#define PUV3_DMA_CH(offset) ((offset) >> 8)
+
+typedef struct {
+ SysBusDevice busdev;
+ MemoryRegion iomem;
+ uint32_t reg_CFG[PUV3_DMA_CH_NR];
+} PUV3DMAState;
+
+static uint64_t puv3_dma_read(void *opaque, target_phys_addr_t offset,
+ unsigned size)
+{
+ PUV3DMAState *s = opaque;
+ uint32_t ret;
+
+ assert(PUV3_DMA_CH(offset) < PUV3_DMA_CH_NR);
+
+ switch (offset & PUV3_DMA_CH_MASK) {
+ case 0x10:
+ ret = s->reg_CFG[PUV3_DMA_CH(offset)];
+ break;
+ default:
+ DPRINTF("Bad offset 0x%x\n", offset);
+ }
+ DPRINTF("offset 0x%x, value 0x%x\n", offset, ret);
+
+ return ret;
+}
+
+static void puv3_dma_write(void *opaque, target_phys_addr_t offset,
+ uint64_t value, unsigned size)
+{
+ PUV3DMAState *s = opaque;
+
+ assert(PUV3_DMA_CH(offset) < PUV3_DMA_CH_NR);
+
+ switch (offset & PUV3_DMA_CH_MASK) {
+ case 0x10:
+ s->reg_CFG[PUV3_DMA_CH(offset)] = value;
+ break;
+ default:
+ DPRINTF("Bad offset 0x%x\n", offset);
+ }
+ DPRINTF("offset 0x%x, value 0x%x\n", offset, value);
+}
+
+static const MemoryRegionOps puv3_dma_ops = {
+ .read = puv3_dma_read,
+ .write = puv3_dma_write,
+ .impl = {
+ .min_access_size = 4,
+ .max_access_size = 4,
+ },
+ .endianness = DEVICE_NATIVE_ENDIAN,
+};
+
+static int puv3_dma_init(SysBusDevice *dev)
+{
+ PUV3DMAState *s = FROM_SYSBUS(PUV3DMAState, dev);
+ int i;
+
+ for (i = 0; i < PUV3_DMA_CH_NR; i++) {
+ s->reg_CFG[i] = 0x0;
+ }
+
+ memory_region_init_io(&s->iomem, &puv3_dma_ops, s, "puv3_dma",
+ PUV3_REGS_OFFSET);
+ sysbus_init_mmio(dev, &s->iomem);
+
+ return 0;
+}
+
+static void puv3_dma_class_init(ObjectClass *klass, void *data)
+{
+ SysBusDeviceClass *sdc = SYS_BUS_DEVICE_CLASS(klass);
+
+ sdc->init = puv3_dma_init;
+}
+
+static const TypeInfo puv3_dma_info = {
+ .name = "puv3_dma",
+ .parent = TYPE_SYS_BUS_DEVICE,
+ .instance_size = sizeof(PUV3DMAState),
+ .class_init = puv3_dma_class_init,
+};
+
+static void puv3_dma_register_type(void)
+{
+ type_register_static(&puv3_dma_info);
+}
+
+type_init(puv3_dma_register_type)
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 13/19] unicore32-softmmu: Add ps2 support
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (11 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 12/19] unicore32-softmmu: Add puv3 dma support gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 14/19] unicore32-softmmu: Add maintainer information for UniCore32 machine gxt
` (6 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch adds ps2/keyboard support, and enables CONFIG_PCKBD.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
default-configs/unicore32-softmmu.mak | 1 +
hw/puv3.c | 5 +++++
2 files changed, 6 insertions(+), 0 deletions(-)
diff --git a/default-configs/unicore32-softmmu.mak b/default-configs/unicore32-softmmu.mak
index 4d4fbfc..de38577 100644
--- a/default-configs/unicore32-softmmu.mak
+++ b/default-configs/unicore32-softmmu.mak
@@ -1,3 +1,4 @@
# Default configuration for unicore32-softmmu
CONFIG_PUV3=y
CONFIG_PTIMER=y
+CONFIG_PCKBD=y
diff --git a/hw/puv3.c b/hw/puv3.c
index 9acfc5a..271df97 100644
--- a/hw/puv3.c
+++ b/hw/puv3.c
@@ -38,6 +38,7 @@ static void puv3_soc_init(CPUUniCore32State *env)
{
qemu_irq *cpu_intc, irqs[PUV3_IRQS_NR];
DeviceState *dev;
+ MemoryRegion *i8042 = g_new(MemoryRegion, 1);
int i;
/* Initialize interrupt controller */
@@ -57,6 +58,10 @@ static void puv3_soc_init(CPUUniCore32State *env)
irqs[PUV3_IRQS_GPIOLOW4], irqs[PUV3_IRQS_GPIOLOW5],
irqs[PUV3_IRQS_GPIOLOW6], irqs[PUV3_IRQS_GPIOLOW7],
irqs[PUV3_IRQS_GPIOHIGH], NULL);
+
+ /* Keyboard (i8042), mouse disabled for nographic */
+ i8042_mm_init(irqs[PUV3_IRQS_PS2_KBD], NULL, i8042, PUV3_REGS_OFFSET, 4);
+ memory_region_add_subregion(get_system_memory(), PUV3_PS2_BASE, i8042);
}
static void puv3_board_init(CPUUniCore32State *env, ram_addr_t ram_size)
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 14/19] unicore32-softmmu: Add maintainer information for UniCore32 machine
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (12 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 13/19] unicore32-softmmu: Add ps2 support gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 15/19] unicore32-softmmu: Add is_default setting for puv3 machine gxt
` (5 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
MAINTAINERS | 8 ++++++++
1 files changed, 8 insertions(+), 0 deletions(-)
diff --git a/MAINTAINERS b/MAINTAINERS
index 2d219d2..708ad54 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -405,6 +405,14 @@ M: Alexander Graf <agraf@suse.de>
S: Maintained
F: hw/s390-*.c
+UniCore32 Machines
+-------------
+PKUnity-3 SoC initramfs-with-busybox
+M: Guan Xuetao <gxt@mprc.pku.edu.cn>
+S: Maintained
+F: hw/puv3*
+F: hw/unicore32/
+
X86 Machines
------------
PC
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 15/19] unicore32-softmmu: Add is_default setting for puv3 machine
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (13 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 14/19] unicore32-softmmu: Add maintainer information for UniCore32 machine gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 16/19] unicore32: Split UniCore-F64 instruction helpers from helper.c gxt
` (4 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: blauwirbel, chenwj, Dunrong Huang, aliguoli, gxt, afaerber
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch sets is_default to 1 for puv3 machine, so that
find_default_machine() returns puv3 machine.
Thanks Dunrong for pointing it out.
Cc: Dunrong Huang <riegamaths@gmail.com>
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
hw/puv3.c | 1 +
1 files changed, 1 insertions(+), 0 deletions(-)
diff --git a/hw/puv3.c b/hw/puv3.c
index 271df97..43f7216 100644
--- a/hw/puv3.c
+++ b/hw/puv3.c
@@ -119,6 +119,7 @@ static QEMUMachine puv3_machine = {
.name = "puv3",
.desc = "PKUnity Version-3 based on UniCore32",
.init = puv3_init,
+ .is_default = 1,
.use_scsi = 0,
};
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 16/19] unicore32: Split UniCore-F64 instruction helpers from helper.c
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (14 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 15/19] unicore32-softmmu: Add is_default setting for puv3 machine gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 17/19] unicore32: Disintegrate cpu_dump_state_ucf64 function gxt
` (3 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch just splits ucf64 instruction simulation helpers from
helper.c.
Also, two checkpatch warnings are solved.
v1->v2: adjust copyright information for new ucf64_helper.c
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
target-unicore32/Makefile.objs | 2 +
target-unicore32/helper.c | 330 -------------------------------------
target-unicore32/ucf64_helper.c | 345 +++++++++++++++++++++++++++++++++++++++
3 files changed, 347 insertions(+), 330 deletions(-)
create mode 100644 target-unicore32/ucf64_helper.c
diff --git a/target-unicore32/Makefile.objs b/target-unicore32/Makefile.objs
index 6af1089..777f01f 100644
--- a/target-unicore32/Makefile.objs
+++ b/target-unicore32/Makefile.objs
@@ -1,4 +1,6 @@
obj-y += translate.o op_helper.o helper.o cpu.o
+obj-y += ucf64_helper.o
+
obj-$(CONFIG_SOFTMMU) += machine.o softmmu.o
$(obj)/op_helper.o: QEMU_CFLAGS += $(HELPER_CFLAGS)
diff --git a/target-unicore32/helper.c b/target-unicore32/helper.c
index f9f1960..d6eb758 100644
--- a/target-unicore32/helper.c
+++ b/target-unicore32/helper.c
@@ -213,333 +213,3 @@ int uc32_cpu_handle_mmu_fault(CPUUniCore32State *env, target_ulong address,
return 1;
}
#endif
-
-/* UniCore-F64 support. We follow the convention used for F64 instrunctions:
- Single precition routines have a "s" suffix, double precision a
- "d" suffix. */
-
-/* Convert host exception flags to f64 form. */
-static inline int ucf64_exceptbits_from_host(int host_bits)
-{
- int target_bits = 0;
-
- if (host_bits & float_flag_invalid) {
- target_bits |= UCF64_FPSCR_FLAG_INVALID;
- }
- if (host_bits & float_flag_divbyzero) {
- target_bits |= UCF64_FPSCR_FLAG_DIVZERO;
- }
- if (host_bits & float_flag_overflow) {
- target_bits |= UCF64_FPSCR_FLAG_OVERFLOW;
- }
- if (host_bits & float_flag_underflow) {
- target_bits |= UCF64_FPSCR_FLAG_UNDERFLOW;
- }
- if (host_bits & float_flag_inexact) {
- target_bits |= UCF64_FPSCR_FLAG_INEXACT;
- }
- return target_bits;
-}
-
-uint32_t HELPER(ucf64_get_fpscr)(CPUUniCore32State *env)
-{
- int i;
- uint32_t fpscr;
-
- fpscr = (env->ucf64.xregs[UC32_UCF64_FPSCR] & UCF64_FPSCR_MASK);
- i = get_float_exception_flags(&env->ucf64.fp_status);
- fpscr |= ucf64_exceptbits_from_host(i);
- return fpscr;
-}
-
-/* Convert ucf64 exception flags to target form. */
-static inline int ucf64_exceptbits_to_host(int target_bits)
-{
- int host_bits = 0;
-
- if (target_bits & UCF64_FPSCR_FLAG_INVALID) {
- host_bits |= float_flag_invalid;
- }
- if (target_bits & UCF64_FPSCR_FLAG_DIVZERO) {
- host_bits |= float_flag_divbyzero;
- }
- if (target_bits & UCF64_FPSCR_FLAG_OVERFLOW) {
- host_bits |= float_flag_overflow;
- }
- if (target_bits & UCF64_FPSCR_FLAG_UNDERFLOW) {
- host_bits |= float_flag_underflow;
- }
- if (target_bits & UCF64_FPSCR_FLAG_INEXACT) {
- host_bits |= float_flag_inexact;
- }
- return host_bits;
-}
-
-void HELPER(ucf64_set_fpscr)(CPUUniCore32State *env, uint32_t val)
-{
- int i;
- uint32_t changed;
-
- changed = env->ucf64.xregs[UC32_UCF64_FPSCR];
- env->ucf64.xregs[UC32_UCF64_FPSCR] = (val & UCF64_FPSCR_MASK);
-
- changed ^= val;
- if (changed & (UCF64_FPSCR_RND_MASK)) {
- i = UCF64_FPSCR_RND(val);
- switch (i) {
- case 0:
- i = float_round_nearest_even;
- break;
- case 1:
- i = float_round_to_zero;
- break;
- case 2:
- i = float_round_up;
- break;
- case 3:
- i = float_round_down;
- break;
- default: /* 100 and 101 not implement */
- cpu_abort(env, "Unsupported UniCore-F64 round mode");
- }
- set_float_rounding_mode(i, &env->ucf64.fp_status);
- }
-
- i = ucf64_exceptbits_to_host(UCF64_FPSCR_TRAPEN(val));
- set_float_exception_flags(i, &env->ucf64.fp_status);
-}
-
-float32 HELPER(ucf64_adds)(float32 a, float32 b, CPUUniCore32State *env)
-{
- return float32_add(a, b, &env->ucf64.fp_status);
-}
-
-float64 HELPER(ucf64_addd)(float64 a, float64 b, CPUUniCore32State *env)
-{
- return float64_add(a, b, &env->ucf64.fp_status);
-}
-
-float32 HELPER(ucf64_subs)(float32 a, float32 b, CPUUniCore32State *env)
-{
- return float32_sub(a, b, &env->ucf64.fp_status);
-}
-
-float64 HELPER(ucf64_subd)(float64 a, float64 b, CPUUniCore32State *env)
-{
- return float64_sub(a, b, &env->ucf64.fp_status);
-}
-
-float32 HELPER(ucf64_muls)(float32 a, float32 b, CPUUniCore32State *env)
-{
- return float32_mul(a, b, &env->ucf64.fp_status);
-}
-
-float64 HELPER(ucf64_muld)(float64 a, float64 b, CPUUniCore32State *env)
-{
- return float64_mul(a, b, &env->ucf64.fp_status);
-}
-
-float32 HELPER(ucf64_divs)(float32 a, float32 b, CPUUniCore32State *env)
-{
- return float32_div(a, b, &env->ucf64.fp_status);
-}
-
-float64 HELPER(ucf64_divd)(float64 a, float64 b, CPUUniCore32State *env)
-{
- return float64_div(a, b, &env->ucf64.fp_status);
-}
-
-float32 HELPER(ucf64_negs)(float32 a)
-{
- return float32_chs(a);
-}
-
-float64 HELPER(ucf64_negd)(float64 a)
-{
- return float64_chs(a);
-}
-
-float32 HELPER(ucf64_abss)(float32 a)
-{
- return float32_abs(a);
-}
-
-float64 HELPER(ucf64_absd)(float64 a)
-{
- return float64_abs(a);
-}
-
-/* XXX: check quiet/signaling case */
-void HELPER(ucf64_cmps)(float32 a, float32 b, uint32_t c, CPUUniCore32State *env)
-{
- int flag;
- flag = float32_compare_quiet(a, b, &env->ucf64.fp_status);
- env->CF = 0;
- switch (c & 0x7) {
- case 0: /* F */
- break;
- case 1: /* UN */
- if (flag == 2) {
- env->CF = 1;
- }
- break;
- case 2: /* EQ */
- if (flag == 0) {
- env->CF = 1;
- }
- break;
- case 3: /* UEQ */
- if ((flag == 0) || (flag == 2)) {
- env->CF = 1;
- }
- break;
- case 4: /* OLT */
- if (flag == -1) {
- env->CF = 1;
- }
- break;
- case 5: /* ULT */
- if ((flag == -1) || (flag == 2)) {
- env->CF = 1;
- }
- break;
- case 6: /* OLE */
- if ((flag == -1) || (flag == 0)) {
- env->CF = 1;
- }
- break;
- case 7: /* ULE */
- if (flag != 1) {
- env->CF = 1;
- }
- break;
- }
- env->ucf64.xregs[UC32_UCF64_FPSCR] = (env->CF << 29)
- | (env->ucf64.xregs[UC32_UCF64_FPSCR] & 0x0fffffff);
-}
-
-void HELPER(ucf64_cmpd)(float64 a, float64 b, uint32_t c, CPUUniCore32State *env)
-{
- int flag;
- flag = float64_compare_quiet(a, b, &env->ucf64.fp_status);
- env->CF = 0;
- switch (c & 0x7) {
- case 0: /* F */
- break;
- case 1: /* UN */
- if (flag == 2) {
- env->CF = 1;
- }
- break;
- case 2: /* EQ */
- if (flag == 0) {
- env->CF = 1;
- }
- break;
- case 3: /* UEQ */
- if ((flag == 0) || (flag == 2)) {
- env->CF = 1;
- }
- break;
- case 4: /* OLT */
- if (flag == -1) {
- env->CF = 1;
- }
- break;
- case 5: /* ULT */
- if ((flag == -1) || (flag == 2)) {
- env->CF = 1;
- }
- break;
- case 6: /* OLE */
- if ((flag == -1) || (flag == 0)) {
- env->CF = 1;
- }
- break;
- case 7: /* ULE */
- if (flag != 1) {
- env->CF = 1;
- }
- break;
- }
- env->ucf64.xregs[UC32_UCF64_FPSCR] = (env->CF << 29)
- | (env->ucf64.xregs[UC32_UCF64_FPSCR] & 0x0fffffff);
-}
-
-/* Helper routines to perform bitwise copies between float and int. */
-static inline float32 ucf64_itos(uint32_t i)
-{
- union {
- uint32_t i;
- float32 s;
- } v;
-
- v.i = i;
- return v.s;
-}
-
-static inline uint32_t ucf64_stoi(float32 s)
-{
- union {
- uint32_t i;
- float32 s;
- } v;
-
- v.s = s;
- return v.i;
-}
-
-static inline float64 ucf64_itod(uint64_t i)
-{
- union {
- uint64_t i;
- float64 d;
- } v;
-
- v.i = i;
- return v.d;
-}
-
-static inline uint64_t ucf64_dtoi(float64 d)
-{
- union {
- uint64_t i;
- float64 d;
- } v;
-
- v.d = d;
- return v.i;
-}
-
-/* Integer to float conversion. */
-float32 HELPER(ucf64_si2sf)(float32 x, CPUUniCore32State *env)
-{
- return int32_to_float32(ucf64_stoi(x), &env->ucf64.fp_status);
-}
-
-float64 HELPER(ucf64_si2df)(float32 x, CPUUniCore32State *env)
-{
- return int32_to_float64(ucf64_stoi(x), &env->ucf64.fp_status);
-}
-
-/* Float to integer conversion. */
-float32 HELPER(ucf64_sf2si)(float32 x, CPUUniCore32State *env)
-{
- return ucf64_itos(float32_to_int32(x, &env->ucf64.fp_status));
-}
-
-float32 HELPER(ucf64_df2si)(float64 x, CPUUniCore32State *env)
-{
- return ucf64_itos(float64_to_int32(x, &env->ucf64.fp_status));
-}
-
-/* floating point conversion */
-float64 HELPER(ucf64_sf2df)(float32 x, CPUUniCore32State *env)
-{
- return float32_to_float64(x, &env->ucf64.fp_status);
-}
-
-float32 HELPER(ucf64_df2sf)(float64 x, CPUUniCore32State *env)
-{
- return float64_to_float32(x, &env->ucf64.fp_status);
-}
diff --git a/target-unicore32/ucf64_helper.c b/target-unicore32/ucf64_helper.c
new file mode 100644
index 0000000..a516edd
--- /dev/null
+++ b/target-unicore32/ucf64_helper.c
@@ -0,0 +1,345 @@
+/*
+ * UniCore-F64 simulation helpers for QEMU.
+ *
+ * Copyright (C) 2010-2012 Guan Xuetao
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation, or any later version.
+ * See the COPYING file in the top-level directory.
+ */
+#include "cpu.h"
+#include "helper.h"
+
+/*
+ * The convention used for UniCore-F64 instructions:
+ * Single precition routines have a "s" suffix
+ * Double precision routines have a "d" suffix.
+ */
+
+/* Convert host exception flags to f64 form. */
+static inline int ucf64_exceptbits_from_host(int host_bits)
+{
+ int target_bits = 0;
+
+ if (host_bits & float_flag_invalid) {
+ target_bits |= UCF64_FPSCR_FLAG_INVALID;
+ }
+ if (host_bits & float_flag_divbyzero) {
+ target_bits |= UCF64_FPSCR_FLAG_DIVZERO;
+ }
+ if (host_bits & float_flag_overflow) {
+ target_bits |= UCF64_FPSCR_FLAG_OVERFLOW;
+ }
+ if (host_bits & float_flag_underflow) {
+ target_bits |= UCF64_FPSCR_FLAG_UNDERFLOW;
+ }
+ if (host_bits & float_flag_inexact) {
+ target_bits |= UCF64_FPSCR_FLAG_INEXACT;
+ }
+ return target_bits;
+}
+
+uint32_t HELPER(ucf64_get_fpscr)(CPUUniCore32State *env)
+{
+ int i;
+ uint32_t fpscr;
+
+ fpscr = (env->ucf64.xregs[UC32_UCF64_FPSCR] & UCF64_FPSCR_MASK);
+ i = get_float_exception_flags(&env->ucf64.fp_status);
+ fpscr |= ucf64_exceptbits_from_host(i);
+ return fpscr;
+}
+
+/* Convert ucf64 exception flags to target form. */
+static inline int ucf64_exceptbits_to_host(int target_bits)
+{
+ int host_bits = 0;
+
+ if (target_bits & UCF64_FPSCR_FLAG_INVALID) {
+ host_bits |= float_flag_invalid;
+ }
+ if (target_bits & UCF64_FPSCR_FLAG_DIVZERO) {
+ host_bits |= float_flag_divbyzero;
+ }
+ if (target_bits & UCF64_FPSCR_FLAG_OVERFLOW) {
+ host_bits |= float_flag_overflow;
+ }
+ if (target_bits & UCF64_FPSCR_FLAG_UNDERFLOW) {
+ host_bits |= float_flag_underflow;
+ }
+ if (target_bits & UCF64_FPSCR_FLAG_INEXACT) {
+ host_bits |= float_flag_inexact;
+ }
+ return host_bits;
+}
+
+void HELPER(ucf64_set_fpscr)(CPUUniCore32State *env, uint32_t val)
+{
+ int i;
+ uint32_t changed;
+
+ changed = env->ucf64.xregs[UC32_UCF64_FPSCR];
+ env->ucf64.xregs[UC32_UCF64_FPSCR] = (val & UCF64_FPSCR_MASK);
+
+ changed ^= val;
+ if (changed & (UCF64_FPSCR_RND_MASK)) {
+ i = UCF64_FPSCR_RND(val);
+ switch (i) {
+ case 0:
+ i = float_round_nearest_even;
+ break;
+ case 1:
+ i = float_round_to_zero;
+ break;
+ case 2:
+ i = float_round_up;
+ break;
+ case 3:
+ i = float_round_down;
+ break;
+ default: /* 100 and 101 not implement */
+ cpu_abort(env, "Unsupported UniCore-F64 round mode");
+ }
+ set_float_rounding_mode(i, &env->ucf64.fp_status);
+ }
+
+ i = ucf64_exceptbits_to_host(UCF64_FPSCR_TRAPEN(val));
+ set_float_exception_flags(i, &env->ucf64.fp_status);
+}
+
+float32 HELPER(ucf64_adds)(float32 a, float32 b, CPUUniCore32State *env)
+{
+ return float32_add(a, b, &env->ucf64.fp_status);
+}
+
+float64 HELPER(ucf64_addd)(float64 a, float64 b, CPUUniCore32State *env)
+{
+ return float64_add(a, b, &env->ucf64.fp_status);
+}
+
+float32 HELPER(ucf64_subs)(float32 a, float32 b, CPUUniCore32State *env)
+{
+ return float32_sub(a, b, &env->ucf64.fp_status);
+}
+
+float64 HELPER(ucf64_subd)(float64 a, float64 b, CPUUniCore32State *env)
+{
+ return float64_sub(a, b, &env->ucf64.fp_status);
+}
+
+float32 HELPER(ucf64_muls)(float32 a, float32 b, CPUUniCore32State *env)
+{
+ return float32_mul(a, b, &env->ucf64.fp_status);
+}
+
+float64 HELPER(ucf64_muld)(float64 a, float64 b, CPUUniCore32State *env)
+{
+ return float64_mul(a, b, &env->ucf64.fp_status);
+}
+
+float32 HELPER(ucf64_divs)(float32 a, float32 b, CPUUniCore32State *env)
+{
+ return float32_div(a, b, &env->ucf64.fp_status);
+}
+
+float64 HELPER(ucf64_divd)(float64 a, float64 b, CPUUniCore32State *env)
+{
+ return float64_div(a, b, &env->ucf64.fp_status);
+}
+
+float32 HELPER(ucf64_negs)(float32 a)
+{
+ return float32_chs(a);
+}
+
+float64 HELPER(ucf64_negd)(float64 a)
+{
+ return float64_chs(a);
+}
+
+float32 HELPER(ucf64_abss)(float32 a)
+{
+ return float32_abs(a);
+}
+
+float64 HELPER(ucf64_absd)(float64 a)
+{
+ return float64_abs(a);
+}
+
+void HELPER(ucf64_cmps)(float32 a, float32 b, uint32_t c,
+ CPUUniCore32State *env)
+{
+ int flag;
+ flag = float32_compare_quiet(a, b, &env->ucf64.fp_status);
+ env->CF = 0;
+ switch (c & 0x7) {
+ case 0: /* F */
+ break;
+ case 1: /* UN */
+ if (flag == 2) {
+ env->CF = 1;
+ }
+ break;
+ case 2: /* EQ */
+ if (flag == 0) {
+ env->CF = 1;
+ }
+ break;
+ case 3: /* UEQ */
+ if ((flag == 0) || (flag == 2)) {
+ env->CF = 1;
+ }
+ break;
+ case 4: /* OLT */
+ if (flag == -1) {
+ env->CF = 1;
+ }
+ break;
+ case 5: /* ULT */
+ if ((flag == -1) || (flag == 2)) {
+ env->CF = 1;
+ }
+ break;
+ case 6: /* OLE */
+ if ((flag == -1) || (flag == 0)) {
+ env->CF = 1;
+ }
+ break;
+ case 7: /* ULE */
+ if (flag != 1) {
+ env->CF = 1;
+ }
+ break;
+ }
+ env->ucf64.xregs[UC32_UCF64_FPSCR] = (env->CF << 29)
+ | (env->ucf64.xregs[UC32_UCF64_FPSCR] & 0x0fffffff);
+}
+
+void HELPER(ucf64_cmpd)(float64 a, float64 b, uint32_t c,
+ CPUUniCore32State *env)
+{
+ int flag;
+ flag = float64_compare_quiet(a, b, &env->ucf64.fp_status);
+ env->CF = 0;
+ switch (c & 0x7) {
+ case 0: /* F */
+ break;
+ case 1: /* UN */
+ if (flag == 2) {
+ env->CF = 1;
+ }
+ break;
+ case 2: /* EQ */
+ if (flag == 0) {
+ env->CF = 1;
+ }
+ break;
+ case 3: /* UEQ */
+ if ((flag == 0) || (flag == 2)) {
+ env->CF = 1;
+ }
+ break;
+ case 4: /* OLT */
+ if (flag == -1) {
+ env->CF = 1;
+ }
+ break;
+ case 5: /* ULT */
+ if ((flag == -1) || (flag == 2)) {
+ env->CF = 1;
+ }
+ break;
+ case 6: /* OLE */
+ if ((flag == -1) || (flag == 0)) {
+ env->CF = 1;
+ }
+ break;
+ case 7: /* ULE */
+ if (flag != 1) {
+ env->CF = 1;
+ }
+ break;
+ }
+ env->ucf64.xregs[UC32_UCF64_FPSCR] = (env->CF << 29)
+ | (env->ucf64.xregs[UC32_UCF64_FPSCR] & 0x0fffffff);
+}
+
+/* Helper routines to perform bitwise copies between float and int. */
+static inline float32 ucf64_itos(uint32_t i)
+{
+ union {
+ uint32_t i;
+ float32 s;
+ } v;
+
+ v.i = i;
+ return v.s;
+}
+
+static inline uint32_t ucf64_stoi(float32 s)
+{
+ union {
+ uint32_t i;
+ float32 s;
+ } v;
+
+ v.s = s;
+ return v.i;
+}
+
+static inline float64 ucf64_itod(uint64_t i)
+{
+ union {
+ uint64_t i;
+ float64 d;
+ } v;
+
+ v.i = i;
+ return v.d;
+}
+
+static inline uint64_t ucf64_dtoi(float64 d)
+{
+ union {
+ uint64_t i;
+ float64 d;
+ } v;
+
+ v.d = d;
+ return v.i;
+}
+
+/* Integer to float conversion. */
+float32 HELPER(ucf64_si2sf)(float32 x, CPUUniCore32State *env)
+{
+ return int32_to_float32(ucf64_stoi(x), &env->ucf64.fp_status);
+}
+
+float64 HELPER(ucf64_si2df)(float32 x, CPUUniCore32State *env)
+{
+ return int32_to_float64(ucf64_stoi(x), &env->ucf64.fp_status);
+}
+
+/* Float to integer conversion. */
+float32 HELPER(ucf64_sf2si)(float32 x, CPUUniCore32State *env)
+{
+ return ucf64_itos(float32_to_int32(x, &env->ucf64.fp_status));
+}
+
+float32 HELPER(ucf64_df2si)(float64 x, CPUUniCore32State *env)
+{
+ return ucf64_itos(float64_to_int32(x, &env->ucf64.fp_status));
+}
+
+/* floating point conversion */
+float64 HELPER(ucf64_sf2df)(float32 x, CPUUniCore32State *env)
+{
+ return float32_to_float64(x, &env->ucf64.fp_status);
+}
+
+float32 HELPER(ucf64_df2sf)(float64 x, CPUUniCore32State *env)
+{
+ return float64_to_float32(x, &env->ucf64.fp_status);
+}
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 17/19] unicore32: Disintegrate cpu_dump_state_ucf64 function
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (15 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 16/19] unicore32: Split UniCore-F64 instruction helpers from helper.c gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 18/19] unicore32: Close dump-option of " gxt
` (2 subsequent siblings)
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch disintegrates cpu_dump_state_ucf64 function from cpu_dump_state.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
target-unicore32/translate.c | 41 +++++++++++++++++++++++++----------------
1 files changed, 25 insertions(+), 16 deletions(-)
diff --git a/target-unicore32/translate.c b/target-unicore32/translate.c
index 5ee3a59..c74c49a 100644
--- a/target-unicore32/translate.c
+++ b/target-unicore32/translate.c
@@ -2139,11 +2139,11 @@ static const char *cpu_mode_names[16] = {
};
#define UCF64_DUMP_STATE
-void cpu_dump_state(CPUUniCore32State *env, FILE *f, fprintf_function cpu_fprintf,
- int flags)
+#ifdef UCF64_DUMP_STATE
+static void cpu_dump_state_ucf64(CPUUniCore32State *env, FILE *f,
+ fprintf_function cpu_fprintf, int flags)
{
int i;
-#ifdef UCF64_DUMP_STATE
union {
uint32_t i;
float s;
@@ -2155,7 +2155,28 @@ void cpu_dump_state(CPUUniCore32State *env, FILE *f, fprintf_function cpu_fprint
float64 f64;
double d;
} d0;
+
+ for (i = 0; i < 16; i++) {
+ d.d = env->ucf64.regs[i];
+ s0.i = d.l.lower;
+ s1.i = d.l.upper;
+ d0.f64 = d.d;
+ cpu_fprintf(f, "s%02d=%08x(%8g) s%02d=%08x(%8g)",
+ i * 2, (int)s0.i, s0.s,
+ i * 2 + 1, (int)s1.i, s1.s);
+ cpu_fprintf(f, " d%02d=%" PRIx64 "(%8g)\n",
+ i, (uint64_t)d0.f64, d0.d);
+ }
+ cpu_fprintf(f, "FPSCR: %08x\n", (int)env->ucf64.xregs[UC32_UCF64_FPSCR]);
+}
+#else
+#define cpu_dump_state_ucf64(env, file, pr, flags) do { } while (0)
#endif
+
+void cpu_dump_state(CPUUniCore32State *env, FILE *f,
+ fprintf_function cpu_fprintf, int flags)
+{
+ int i;
uint32_t psr;
for (i = 0; i < 32; i++) {
@@ -2175,19 +2196,7 @@ void cpu_dump_state(CPUUniCore32State *env, FILE *f, fprintf_function cpu_fprint
psr & (1 << 28) ? 'V' : '-',
cpu_mode_names[psr & 0xf]);
-#ifdef UCF64_DUMP_STATE
- for (i = 0; i < 16; i++) {
- d.d = env->ucf64.regs[i];
- s0.i = d.l.lower;
- s1.i = d.l.upper;
- d0.f64 = d.d;
- cpu_fprintf(f, "s%02d=%08x(%8g) s%02d=%08x(%8g) d%02d=%" PRIx64 "(%8g)\n",
- i * 2, (int)s0.i, s0.s,
- i * 2 + 1, (int)s1.i, s1.s,
- i, (uint64_t)d0.f64, d0.d);
- }
- cpu_fprintf(f, "FPSCR: %08x\n", (int)env->ucf64.xregs[UC32_UCF64_FPSCR]);
-#endif
+ cpu_dump_state_ucf64(env, f, cpu_fprintf, flags);
}
void restore_state_to_opc(CPUUniCore32State *env, TranslationBlock *tb, int pc_pos)
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 18/19] unicore32: Close dump-option of cpu_dump_state_ucf64 function
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (16 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 17/19] unicore32: Disintegrate cpu_dump_state_ucf64 function gxt
@ 2012-08-07 10:00 ` gxt
2012-08-07 10:00 ` [Qemu-devel] [PATCH 19/19] unicore32-softmmu: Add a minimal curses screen support gxt
2012-08-09 18:20 ` [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support Blue Swirl
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: aliguoli, blauwirbel, gxt, afaerber, chenwj
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
Since of tedious output, we close dump-option of cpu_dump_state_ucf64 function.
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
target-unicore32/translate.c | 2 +-
1 files changed, 1 insertions(+), 1 deletions(-)
diff --git a/target-unicore32/translate.c b/target-unicore32/translate.c
index c74c49a..188bf8c 100644
--- a/target-unicore32/translate.c
+++ b/target-unicore32/translate.c
@@ -2138,7 +2138,7 @@ static const char *cpu_mode_names[16] = {
"UM18", "UM19", "UM1A", "EXTN", "UM1C", "UM1D", "UM1E", "SUSR"
};
-#define UCF64_DUMP_STATE
+#undef UCF64_DUMP_STATE
#ifdef UCF64_DUMP_STATE
static void cpu_dump_state_ucf64(CPUUniCore32State *env, FILE *f,
fprintf_function cpu_fprintf, int flags)
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* [Qemu-devel] [PATCH 19/19] unicore32-softmmu: Add a minimal curses screen support
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (17 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 18/19] unicore32: Close dump-option of " gxt
@ 2012-08-07 10:00 ` gxt
2012-08-09 18:20 ` [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support Blue Swirl
19 siblings, 0 replies; 22+ messages in thread
From: gxt @ 2012-08-07 10:00 UTC (permalink / raw)
To: qemu-devel; +Cc: blauwirbel, chenwj, aliguoli, Zhang Mengchi, gxt, afaerber
From: Guan Xuetao <gxt@mprc.pku.edu.cn>
This patch adds a minimal curses screen support for unicore32-softmmu.
We assume 80*30 screen size to minimize the implementation.
Two problems are not solved, but they are innocuous.
1. curses windows will be blank when switching to monitor screen and back
2. backspace is not handled yet
v1->v2: add extra handler for '\r'
Signed-off-by: Zhang Mengchi <zhangmengchi@mprc.pku.edu.cn>
Signed-off-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
---
target-unicore32/helper.c | 45 +++++++++++++++++++++++++++++++++++++++++++--
1 files changed, 43 insertions(+), 2 deletions(-)
diff --git a/target-unicore32/helper.c b/target-unicore32/helper.c
index d6eb758..d21e7df 100644
--- a/target-unicore32/helper.c
+++ b/target-unicore32/helper.c
@@ -13,6 +13,7 @@
#include "gdbstub.h"
#include "helper.h"
#include "host-utils.h"
+#include "console.h"
#undef DEBUG_UC32
@@ -186,10 +187,50 @@ uint32_t helper_cp0_get(CPUUniCore32State *env, uint32_t creg, uint32_t cop)
return 0;
}
+#ifdef CONFIG_CURSES
+/*
+ * FIXME:
+ * 1. curses windows will be blank when switching back
+ * 2. backspace is not handled yet
+ */
+static void putc_on_screen(unsigned char ch)
+{
+ static WINDOW *localwin;
+ static int init;
+
+ if (!init) {
+ /* Assume 80 * 30 screen to minimize the implementation */
+ localwin = newwin(30, 80, 0, 0);
+ scrollok(localwin, TRUE);
+ init = TRUE;
+ }
+
+ if (isprint(ch)) {
+ wprintw(localwin, "%c", ch);
+ } else {
+ switch (ch) {
+ case '\n':
+ wprintw(localwin, "%c", ch);
+ break;
+ case '\r':
+ /* If '\r' is put before '\n', the curses window will destroy the
+ * last print line. And meanwhile, '\n' implifies '\r' inside. */
+ break;
+ default: /* Not handled, so just print it hex code */
+ wprintw(localwin, "-- 0x%h --", ch);
+ }
+ }
+
+ wrefresh(localwin);
+}
+#else
+#define putc_on_screen(c) do { } while (0)
+#endif
+
void helper_cp1_putc(target_ulong x)
{
- /* TODO: curses display should be added here for screen output. */
- DPRINTF("%c", x);
+ putc_on_screen((unsigned char)x); /* Output to screen */
+ DPRINTF("%c", x); /* Output to stdout */
}
#endif
--
1.7.0.4
^ permalink raw reply related [flat|nested] 22+ messages in thread* Re: [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support
2012-08-07 10:00 [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support gxt
` (18 preceding siblings ...)
2012-08-07 10:00 ` [Qemu-devel] [PATCH 19/19] unicore32-softmmu: Add a minimal curses screen support gxt
@ 2012-08-09 18:20 ` Blue Swirl
2012-08-10 2:33 ` guanxuetao
19 siblings, 1 reply; 22+ messages in thread
From: Blue Swirl @ 2012-08-09 18:20 UTC (permalink / raw)
To: gxt; +Cc: aliguori, riegamaths, qemu-devel, chenwj, afaerber
On Tue, Aug 7, 2012 at 10:00 AM, <gxt@mprc.pku.edu.cn> wrote:
> From: Guan Xuetao <gxt@mprc.pku.edu.cn>
>
> These patches implement softmmu support on unicore32 architecture.
> Based on master branch of qemu, these patches can be fetched from:
> git://github.com/gxt/QEMU.git for-review
>
> UniCore32 CPU is embedded in PKUnity-3 SoC, so we add necessary puv3
> devices simulation codes together.
> Only minimal system control modules are simulated, to make linux kernel
> boot and busybox run in initramfs.
>
> Thanks Andreas Farber, Blue Swirl, Chen Weiren and Dunrong Huang for
> their priceless advice.
>
> Any advice is greatly appreciated.
This still breaks build. Please fix, something like ret = 0 when the
variable is declared should be enough.
/src/qemu/hw/puv3_gpio.c: In function 'puv3_gpio_read':
/src/qemu/hw/puv3_gpio.c:48:5: error: 'ret' may be used uninitialized
in this function [-Werror=maybe-uninitialized]
/src/qemu/hw/puv3_pm.c: In function 'puv3_pm_read':
/src/qemu/hw/puv3_pm.c:74:5: error: 'ret' may be used uninitialized in
this function [-Werror=maybe-uninitialized]
/src/qemu/hw/puv3_dma.c: In function 'puv3_dma_read':
/src/qemu/hw/puv3_dma.c:44:5: error: 'ret' may be used uninitialized
in this function [-Werror=maybe-uninitialized]
I won't apply the patches until this is fixed.
>
> Thanks,
>
> Guan Xuetao
> ---
>
> Andreas Färber (1):
> target-unicore32: Drop UC32_CPUID macros
>
> Guan Xuetao (18):
> unicore32-softmmu: Add unicore32-softmmu build support
> unicore32-softmmu: Add coprocessor 0(sysctrl) and 1(ocd) instruction
> support
> unicore32-softmmu: Make UniCore32 cpuid & exceptions correct and
> runable
> unicore32-softmmu: Implement softmmu specific functions
> unicore32-softmmu: Make sure that kernel can access user space
> unicore32-softmmu: Add puv3 soc/board support
> unicore32-softmmu: Add puv3 interrupt support
> unicore32-softmmu: Add puv3 ostimer support
> unicore32-softmmu: Add puv3 gpio support
> unicore32-softmmu: Add puv3 pm support
> unicore32-softmmu: Add puv3 dma support
> unicore32-softmmu: Add ps2 support
> unicore32-softmmu: Add maintainer information for UniCore32 machine
> unicore32-softmmu: Add is_default setting for puv3 machine
> unicore32: Split UniCore-F64 instruction helpers from helper.c
> unicore32: Disintegrate cpu_dump_state_ucf64 function
> unicore32: Close dump-option of cpu_dump_state_ucf64 function
> unicore32-softmmu: Add a minimal curses screen support
>
> MAINTAINERS | 8 +
> arch_init.c | 2 +
> arch_init.h | 1 +
> configure | 1 +
> cpu-exec.c | 1 +
> default-configs/unicore32-softmmu.mak | 4 +
> hw/Makefile.objs | 7 +
> hw/puv3.c | 131 +++++++++
> hw/puv3.h | 49 ++++
> hw/puv3_dma.c | 109 +++++++
> hw/puv3_gpio.c | 141 +++++++++
> hw/puv3_intc.c | 135 +++++++++
> hw/puv3_ost.c | 151 ++++++++++
> hw/puv3_pm.c | 149 ++++++++++
> hw/unicore32/Makefile.objs | 6 +
> linux-user/main.c | 3 +-
> target-unicore32/Makefile.objs | 4 +-
> target-unicore32/cpu.c | 19 +-
> target-unicore32/cpu.h | 18 +-
> target-unicore32/helper.c | 511 +++++++++++----------------------
> target-unicore32/helper.h | 17 +-
> target-unicore32/machine.c | 23 ++
> target-unicore32/op_helper.c | 44 +++-
> target-unicore32/softmmu.c | 267 +++++++++++++++++
> target-unicore32/translate.c | 159 +++++++++--
> target-unicore32/ucf64_helper.c | 345 ++++++++++++++++++++++
> 26 files changed, 1904 insertions(+), 401 deletions(-)
> create mode 100644 default-configs/unicore32-softmmu.mak
> create mode 100644 hw/puv3.c
> create mode 100644 hw/puv3.h
> create mode 100644 hw/puv3_dma.c
> create mode 100644 hw/puv3_gpio.c
> create mode 100644 hw/puv3_intc.c
> create mode 100644 hw/puv3_ost.c
> create mode 100644 hw/puv3_pm.c
> create mode 100644 hw/unicore32/Makefile.objs
> create mode 100644 target-unicore32/machine.c
> create mode 100644 target-unicore32/softmmu.c
> create mode 100644 target-unicore32/ucf64_helper.c
>
^ permalink raw reply [flat|nested] 22+ messages in thread* Re: [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support
2012-08-09 18:20 ` [Qemu-devel] [PATCH 00/19] unicore32: Add unicore32-softmmu support Blue Swirl
@ 2012-08-10 2:33 ` guanxuetao
0 siblings, 0 replies; 22+ messages in thread
From: guanxuetao @ 2012-08-10 2:33 UTC (permalink / raw)
To: Blue Swirl; +Cc: aliguori, chenwj, qemu-devel, riegamaths, gxt, afaerber
>
> This still breaks build. Please fix, something like ret = 0 when the
> variable is declared should be enough.
> /src/qemu/hw/puv3_gpio.c: In function 'puv3_gpio_read':
> /src/qemu/hw/puv3_gpio.c:48:5: error: 'ret' may be used uninitialized
> in this function [-Werror=maybe-uninitialized]
> /src/qemu/hw/puv3_pm.c: In function 'puv3_pm_read':
> /src/qemu/hw/puv3_pm.c:74:5: error: 'ret' may be used uninitialized in
> this function [-Werror=maybe-uninitialized]
> /src/qemu/hw/puv3_dma.c: In function 'puv3_dma_read':
> /src/qemu/hw/puv3_dma.c:44:5: error: 'ret' may be used uninitialized
> in this function [-Werror=maybe-uninitialized]
>
> I won't apply the patches until this is fixed.
>
My mistake. I'm sorry for that.
Thanks & Regard,
Guan Xuetao
^ permalink raw reply [flat|nested] 22+ messages in thread