* [Qemu-devel] [PATCH 0/2] nvic: Handle ARMv6-M SCS reserved registers @ 2018-07-04 19:58 Julia Suvorova 2018-07-04 19:58 ` [Qemu-devel] [PATCH 1/2] " Julia Suvorova 2018-07-04 19:58 ` [Qemu-devel] [RFC 2/2] tests: Add ARMv6-M reserved register test Julia Suvorova 0 siblings, 2 replies; 6+ messages in thread From: Julia Suvorova @ 2018-07-04 19:58 UTC (permalink / raw) To: qemu-devel Cc: Peter Maydell, Stefan Hajnoczi, Joel Stanley, Jim Mussared, Steffen Görtz, Julia Suvorova Julia Suvorova (2): nvic: Handle ARMv6-M SCS reserved registers tests: Add ARMv6-M reserved register test hw/intc/armv7m_nvic.c | 69 +++++++++++++++++++++++++------ tests/Makefile.include | 2 + tests/tcg/arm/test-reserved-reg.c | 60 +++++++++++++++++++++++++++ 3 files changed, 119 insertions(+), 12 deletions(-) create mode 100644 tests/tcg/arm/test-reserved-reg.c -- 2.17.1 ^ permalink raw reply [flat|nested] 6+ messages in thread
* [Qemu-devel] [PATCH 1/2] nvic: Handle ARMv6-M SCS reserved registers 2018-07-04 19:58 [Qemu-devel] [PATCH 0/2] nvic: Handle ARMv6-M SCS reserved registers Julia Suvorova @ 2018-07-04 19:58 ` Julia Suvorova 2018-07-05 10:54 ` Peter Maydell 2018-07-04 19:58 ` [Qemu-devel] [RFC 2/2] tests: Add ARMv6-M reserved register test Julia Suvorova 1 sibling, 1 reply; 6+ messages in thread From: Julia Suvorova @ 2018-07-04 19:58 UTC (permalink / raw) To: qemu-devel Cc: Peter Maydell, Stefan Hajnoczi, Joel Stanley, Jim Mussared, Steffen Görtz, Julia Suvorova Handle SCS reserved registers listed in ARMv6-M ARM D3.6.1. All reserved registers are RAZ/WI. Signed-off-by: Julia Suvorova <jusual@mail.ru> --- hw/intc/armv7m_nvic.c | 69 +++++++++++++++++++++++++++++++++++-------- 1 file changed, 57 insertions(+), 12 deletions(-) diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c index aba4510c70..fb61a1d08d 100644 --- a/hw/intc/armv7m_nvic.c +++ b/hw/intc/armv7m_nvic.c @@ -865,6 +865,9 @@ static uint32_t nvic_readl(NVICState *s, uint32_t offset, MemTxAttrs attrs) } return val; case 0xd10: /* System Control. */ + if (!arm_feature(&cpu->env, ARM_FEATURE_V7)) { + return 0; + } return cpu->env.v7m.scr[attrs.secure]; case 0xd14: /* Configuration Control. */ /* The BFHFNMIGN bit is the only non-banked bit; we @@ -986,12 +989,21 @@ static uint32_t nvic_readl(NVICState *s, uint32_t offset, MemTxAttrs attrs) } return val; case 0xd2c: /* Hard Fault Status. */ + if (!arm_feature(&cpu->env, ARM_FEATURE_V7)) { + return 0; + } return cpu->env.v7m.hfsr; case 0xd30: /* Debug Fault Status. */ return cpu->env.v7m.dfsr; case 0xd34: /* MMFAR MemManage Fault Address */ + if (!arm_feature(&cpu->env, ARM_FEATURE_V7)) { + return 0; + } return cpu->env.v7m.mmfar[attrs.secure]; case 0xd38: /* Bus Fault Address. */ + if (!arm_feature(&cpu->env, ARM_FEATURE_V7)) { + return 0; + } return cpu->env.v7m.bfar; case 0xd3c: /* Aux Fault Status. */ /* TODO: Implement fault status registers. */ @@ -1292,8 +1304,10 @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, * QEMU's implementation ignores SEVONPEND and SLEEPONEXIT, which * is architecturally permitted. */ - value &= ~(R_V7M_SCR_SLEEPDEEP_MASK | R_V7M_SCR_SLEEPDEEPS_MASK); - cpu->env.v7m.scr[attrs.secure] = value; + if (arm_feature(&cpu->env, ARM_FEATURE_V7)) { + value &= ~(R_V7M_SCR_SLEEPDEEP_MASK | R_V7M_SCR_SLEEPDEEPS_MASK); + cpu->env.v7m.scr[attrs.secure] = value; + } break; case 0xd14: /* Configuration Control. */ /* Enforce RAZ/WI on reserved and must-RAZ/WI bits */ @@ -1388,16 +1402,22 @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, nvic_irq_update(s); break; case 0xd2c: /* Hard Fault Status. */ - cpu->env.v7m.hfsr &= ~value; /* W1C */ + if (arm_feature(&cpu->env, ARM_FEATURE_V7)) { + cpu->env.v7m.hfsr &= ~value; /* W1C */ + } break; case 0xd30: /* Debug Fault Status. */ cpu->env.v7m.dfsr &= ~value; /* W1C */ break; case 0xd34: /* Mem Manage Address. */ - cpu->env.v7m.mmfar[attrs.secure] = value; + if (arm_feature(&cpu->env, ARM_FEATURE_V7)) { + cpu->env.v7m.mmfar[attrs.secure] = value; + } return; case 0xd38: /* Bus Fault Address. */ - cpu->env.v7m.bfar = value; + if (arm_feature(&cpu->env, ARM_FEATURE_V7)) { + cpu->env.v7m.bfar = value; + } return; case 0xd3c: /* Aux Fault Status. */ qemu_log_mask(LOG_UNIMP, @@ -1624,13 +1644,13 @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, cpu->env.v7m.sfsr = value; break; case 0xf00: /* Software Triggered Interrupt Register */ - { - int excnum = (value & 0x1ff) + NVIC_FIRST_IRQ; - if (excnum < s->num_irq) { - armv7m_nvic_set_pending(s, excnum, false); + if (arm_feature(&cpu->env, ARM_FEATURE_V7)) { + int excnum = (value & 0x1ff) + NVIC_FIRST_IRQ; + if (excnum < s->num_irq) { + armv7m_nvic_set_pending(s, excnum, false); + } } break; - } case 0xf50: /* ICIALLU */ case 0xf58: /* ICIMVAU */ case 0xf5c: /* DCIMVAC */ @@ -1775,7 +1795,13 @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, } } break; - case 0xd18 ... 0xd23: /* System Handler Priority (SHPR1, SHPR2, SHPR3) */ + case 0xd18: /* System Handler Priority (SHPR1) */ + if (!arm_feature(&s->cpu->env, ARM_FEATURE_V7)) { + val = 0; + break; + } + /* fall through */ + case 0xd1c ... 0xd23: /* System Handler Priority (SHPR2, SHPR3) */ val = 0; for (i = 0; i < size; i++) { unsigned hdlidx = (offset - 0xd14) + i; @@ -1791,10 +1817,20 @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, /* The BFSR bits [15:8] are shared between security states * and we store them in the NS copy */ + if (!arm_feature(&s->cpu->env, ARM_FEATURE_V7)) { + val = 0; + break; + }; val = s->cpu->env.v7m.cfsr[attrs.secure]; val |= s->cpu->env.v7m.cfsr[M_REG_NS] & R_V7M_CFSR_BFSR_MASK; val = extract32(val, (offset - 0xd28) * 8, size * 8); break; + case 0xd40 ... 0xd7c: /* CPUID registers */ + if (!arm_feature(&s->cpu->env, ARM_FEATURE_V7)) { + val = 0; + break; + } + goto proceed_to_readl; case 0xfe0 ... 0xfff: /* ID. */ if (offset & 3) { val = 0; @@ -1803,6 +1839,7 @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, } break; default: + proceed_to_readl: if (size == 4) { val = nvic_readl(s, offset, attrs); } else { @@ -1882,7 +1919,12 @@ static MemTxResult nvic_sysreg_write(void *opaque, hwaddr addr, } nvic_irq_update(s); return MEMTX_OK; - case 0xd18 ... 0xd23: /* System Handler Priority (SHPR1, SHPR2, SHPR3) */ + case 0xd18: /* System Handler Priority (SHPR1) */ + if (!arm_feature(&s->cpu->env, ARM_FEATURE_V7)) { + return MEMTX_OK; + } + /* fall through */ + case 0xd1c ... 0xd23: /* System Handler Priority (SHPR2, SHPR3) */ for (i = 0; i < size; i++) { unsigned hdlidx = (offset - 0xd14) + i; int newprio = extract32(value, i * 8, 8); @@ -1899,6 +1941,9 @@ static MemTxResult nvic_sysreg_write(void *opaque, hwaddr addr, /* All bits are W1C, so construct 32 bit value with 0s in * the parts not written by the access size */ + if (!arm_feature(&s->cpu->env, ARM_FEATURE_V7)) { + return MEMTX_OK; + } value <<= ((offset - 0xd28) * 8); s->cpu->env.v7m.cfsr[attrs.secure] &= ~value; -- 2.17.1 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [Qemu-devel] [PATCH 1/2] nvic: Handle ARMv6-M SCS reserved registers 2018-07-04 19:58 ` [Qemu-devel] [PATCH 1/2] " Julia Suvorova @ 2018-07-05 10:54 ` Peter Maydell 2018-07-05 11:25 ` Julia Suvorova 0 siblings, 1 reply; 6+ messages in thread From: Peter Maydell @ 2018-07-05 10:54 UTC (permalink / raw) To: Julia Suvorova Cc: QEMU Developers, Stefan Hajnoczi, Joel Stanley, Jim Mussared, Steffen Görtz On 4 July 2018 at 20:58, Julia Suvorova <jusual@mail.ru> wrote: > Handle SCS reserved registers listed in ARMv6-M ARM D3.6.1. > All reserved registers are RAZ/WI. > > Signed-off-by: Julia Suvorova <jusual@mail.ru> > --- > hw/intc/armv7m_nvic.c | 69 +++++++++++++++++++++++++++++++++++-------- > 1 file changed, 57 insertions(+), 12 deletions(-) Hi; this patch is generally good, but I have a couple of comments below, and in most (but not all) of these cases we should be checking the ARM_FEATURE_M_MAIN bit rather than ARM_FEATURE_V7 -- I've annotated which should be which. > diff --git a/hw/intc/armv7m_nvic.c b/hw/intc/armv7m_nvic.c > index aba4510c70..fb61a1d08d 100644 > --- a/hw/intc/armv7m_nvic.c > +++ b/hw/intc/armv7m_nvic.c > @@ -865,6 +865,9 @@ static uint32_t nvic_readl(NVICState *s, uint32_t offset, MemTxAttrs attrs) > } > return val; > case 0xd10: /* System Control. */ > + if (!arm_feature(&cpu->env, ARM_FEATURE_V7)) { > + return 0; > + } This check is correctly on ARM_FEATURE_V7. Also, I would suggest having the "not in this version" behaviour for all these checks be "goto bad_offset;" as we do already for the v8-only registers. This will make the register RAZ/WI, but it will also log that the guest did something wrong if the user enables guest-error logging. > return cpu->env.v7m.scr[attrs.secure]; > case 0xd14: /* Configuration Control. */ > /* The BFHFNMIGN bit is the only non-banked bit; we > @@ -986,12 +989,21 @@ static uint32_t nvic_readl(NVICState *s, uint32_t offset, MemTxAttrs attrs) > } > return val; > case 0xd2c: /* Hard Fault Status. */ > + if (!arm_feature(&cpu->env, ARM_FEATURE_V7)) { This one should check ARM_FEATURE_M_MAIN. > + return 0; > + } > return cpu->env.v7m.hfsr; > case 0xd30: /* Debug Fault Status. */ > return cpu->env.v7m.dfsr; > case 0xd34: /* MMFAR MemManage Fault Address */ > + if (!arm_feature(&cpu->env, ARM_FEATURE_V7)) { > + return 0; > + } M_MAIN > return cpu->env.v7m.mmfar[attrs.secure]; > case 0xd38: /* Bus Fault Address. */ > + if (!arm_feature(&cpu->env, ARM_FEATURE_V7)) { > + return 0; > + } M_MAIN > return cpu->env.v7m.bfar; > case 0xd3c: /* Aux Fault Status. */ > /* TODO: Implement fault status registers. */ > @@ -1292,8 +1304,10 @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, > * QEMU's implementation ignores SEVONPEND and SLEEPONEXIT, which > * is architecturally permitted. > */ > - value &= ~(R_V7M_SCR_SLEEPDEEP_MASK | R_V7M_SCR_SLEEPDEEPS_MASK); > - cpu->env.v7m.scr[attrs.secure] = value; > + if (arm_feature(&cpu->env, ARM_FEATURE_V7)) { > + value &= ~(R_V7M_SCR_SLEEPDEEP_MASK | R_V7M_SCR_SLEEPDEEPS_MASK); > + cpu->env.v7m.scr[attrs.secure] = value; > + } OK. As with the readl checks, prefer if !arm_feature(...)) { goto bad_offset; } [code for register here] > break; > case 0xd14: /* Configuration Control. */ > /* Enforce RAZ/WI on reserved and must-RAZ/WI bits */ > @@ -1388,16 +1402,22 @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, > nvic_irq_update(s); > break; > case 0xd2c: /* Hard Fault Status. */ > - cpu->env.v7m.hfsr &= ~value; /* W1C */ > + if (arm_feature(&cpu->env, ARM_FEATURE_V7)) { > + cpu->env.v7m.hfsr &= ~value; /* W1C */ > + } M_MAIN. > break; > case 0xd30: /* Debug Fault Status. */ > cpu->env.v7m.dfsr &= ~value; /* W1C */ > break; > case 0xd34: /* Mem Manage Address. */ > - cpu->env.v7m.mmfar[attrs.secure] = value; > + if (arm_feature(&cpu->env, ARM_FEATURE_V7)) { > + cpu->env.v7m.mmfar[attrs.secure] = value; > + } M_MAIN. > return; > case 0xd38: /* Bus Fault Address. */ > - cpu->env.v7m.bfar = value; > + if (arm_feature(&cpu->env, ARM_FEATURE_V7)) { > + cpu->env.v7m.bfar = value; > + } M_MAIN. > return; > case 0xd3c: /* Aux Fault Status. */ > qemu_log_mask(LOG_UNIMP, > @@ -1624,13 +1644,13 @@ static void nvic_writel(NVICState *s, uint32_t offset, uint32_t value, > cpu->env.v7m.sfsr = value; > break; > case 0xf00: /* Software Triggered Interrupt Register */ > - { > - int excnum = (value & 0x1ff) + NVIC_FIRST_IRQ; > - if (excnum < s->num_irq) { > - armv7m_nvic_set_pending(s, excnum, false); > + if (arm_feature(&cpu->env, ARM_FEATURE_V7)) { M_MAIN. > + int excnum = (value & 0x1ff) + NVIC_FIRST_IRQ; > + if (excnum < s->num_irq) { > + armv7m_nvic_set_pending(s, excnum, false); > + } > } > break; > - } > case 0xf50: /* ICIALLU */ > case 0xf58: /* ICIMVAU */ > case 0xf5c: /* DCIMVAC */ > @@ -1775,7 +1795,13 @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, > } > } > break; > - case 0xd18 ... 0xd23: /* System Handler Priority (SHPR1, SHPR2, SHPR3) */ > + case 0xd18: /* System Handler Priority (SHPR1) */ > + if (!arm_feature(&s->cpu->env, ARM_FEATURE_V7)) { M_MAIN. > + val = 0; > + break; > + } > + /* fall through */ > + case 0xd1c ... 0xd23: /* System Handler Priority (SHPR2, SHPR3) */ > val = 0; > for (i = 0; i < size; i++) { > unsigned hdlidx = (offset - 0xd14) + i; > @@ -1791,10 +1817,20 @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, > /* The BFSR bits [15:8] are shared between security states > * and we store them in the NS copy > */ > + if (!arm_feature(&s->cpu->env, ARM_FEATURE_V7)) { M_MAIN. > + val = 0; > + break; > + }; > val = s->cpu->env.v7m.cfsr[attrs.secure]; > val |= s->cpu->env.v7m.cfsr[M_REG_NS] & R_V7M_CFSR_BFSR_MASK; > val = extract32(val, (offset - 0xd28) * 8, size * 8); > break; > + case 0xd40 ... 0xd7c: /* CPUID registers */ > + if (!arm_feature(&s->cpu->env, ARM_FEATURE_V7)) { > + val = 0; > + break; > + } > + goto proceed_to_readl; Rather than doing this, I would recommend leaving the armv7m_nvic.c code as it is, and just making sure that the cortex_m0 init function leaves the cpu_id* registers at zero. Then they will RAZ/WI as required. > case 0xfe0 ... 0xfff: /* ID. */ > if (offset & 3) { > val = 0; > @@ -1803,6 +1839,7 @@ static MemTxResult nvic_sysreg_read(void *opaque, hwaddr addr, > } > break; > default: > + proceed_to_readl: > if (size == 4) { > val = nvic_readl(s, offset, attrs); > } else { > @@ -1882,7 +1919,12 @@ static MemTxResult nvic_sysreg_write(void *opaque, hwaddr addr, > } > nvic_irq_update(s); > return MEMTX_OK; > - case 0xd18 ... 0xd23: /* System Handler Priority (SHPR1, SHPR2, SHPR3) */ > + case 0xd18: /* System Handler Priority (SHPR1) */ > + if (!arm_feature(&s->cpu->env, ARM_FEATURE_V7)) { M_MAIN. > + return MEMTX_OK; > + } > + /* fall through */ > + case 0xd1c ... 0xd23: /* System Handler Priority (SHPR2, SHPR3) */ > for (i = 0; i < size; i++) { > unsigned hdlidx = (offset - 0xd14) + i; > int newprio = extract32(value, i * 8, 8); > @@ -1899,6 +1941,9 @@ static MemTxResult nvic_sysreg_write(void *opaque, hwaddr addr, > /* All bits are W1C, so construct 32 bit value with 0s in > * the parts not written by the access size > */ > + if (!arm_feature(&s->cpu->env, ARM_FEATURE_V7)) { > + return MEMTX_OK; > + } M_MAIN. Also, this addition has split the comment above it from the line of code which it is commenting on -- could you move your check to be above the comment, please? > value <<= ((offset - 0xd28) * 8); > > s->cpu->env.v7m.cfsr[attrs.secure] &= ~value; > -- thanks -- PMM ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Qemu-devel] [PATCH 1/2] nvic: Handle ARMv6-M SCS reserved registers 2018-07-05 10:54 ` Peter Maydell @ 2018-07-05 11:25 ` Julia Suvorova 2018-07-05 12:06 ` Peter Maydell 0 siblings, 1 reply; 6+ messages in thread From: Julia Suvorova @ 2018-07-05 11:25 UTC (permalink / raw) To: Peter Maydell Cc: QEMU Developers, Stefan Hajnoczi, Joel Stanley, Jim Mussared, Steffen Görtz On 05.07.2018 13:54, Peter Maydell wrote: > On 4 July 2018 at 20:58, Julia Suvorova <jusual@mail.ru> wrote: >> Handle SCS reserved registers listed in ARMv6-M ARM D3.6.1. >> All reserved registers are RAZ/WI. >> >> Signed-off-by: Julia Suvorova <jusual@mail.ru> >> --- >> hw/intc/armv7m_nvic.c | 69 +++++++++++++++++++++++++++++++++++-------- >> 1 file changed, 57 insertions(+), 12 deletions(-) > > Hi; this patch is generally good, but I have a couple of comments > below, and in most (but not all) of these cases we should be > checking the ARM_FEATURE_M_MAIN bit rather than ARM_FEATURE_V7 -- > I've annotated which should be which. Thank you for the review. I did not dare to set the ARM_FEATURE_M_MAIN, because I was not completely sure about the v8M behavior in certain cases. I'll update the code taking into account all the comments, and send v2. Best regards, Julia Suvorova. ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [Qemu-devel] [PATCH 1/2] nvic: Handle ARMv6-M SCS reserved registers 2018-07-05 11:25 ` Julia Suvorova @ 2018-07-05 12:06 ` Peter Maydell 0 siblings, 0 replies; 6+ messages in thread From: Peter Maydell @ 2018-07-05 12:06 UTC (permalink / raw) To: Julia Suvorova Cc: QEMU Developers, Stefan Hajnoczi, Joel Stanley, Jim Mussared, Steffen Görtz On 5 July 2018 at 12:25, Julia Suvorova <jusual@mail.ru> wrote: > Thank you for the review. I did not dare to set the ARM_FEATURE_M_MAIN, > because I was not completely sure about the v8M behavior in certain cases. > I'll update the code taking into account all the comments, and send v2. FWIW, I was working from the v8M Arm ARM, which is downloadable from https://developer.arm.com/products/architecture/m-profile/docs -- the descriptions for each register include a "Configurations" sections which will say if the register is present only if the main extension is implemented. thanks -- PMM ^ permalink raw reply [flat|nested] 6+ messages in thread
* [Qemu-devel] [RFC 2/2] tests: Add ARMv6-M reserved register test 2018-07-04 19:58 [Qemu-devel] [PATCH 0/2] nvic: Handle ARMv6-M SCS reserved registers Julia Suvorova 2018-07-04 19:58 ` [Qemu-devel] [PATCH 1/2] " Julia Suvorova @ 2018-07-04 19:58 ` Julia Suvorova 1 sibling, 0 replies; 6+ messages in thread From: Julia Suvorova @ 2018-07-04 19:58 UTC (permalink / raw) To: qemu-devel Cc: Peter Maydell, Stefan Hajnoczi, Joel Stanley, Jim Mussared, Steffen Görtz, Julia Suvorova Check that reserved SCS registers return 0 at read, and writes are ignored. Based-on: <20180627143815.1829-1-joel@jms.id.au> Based-on: <20180630091343.14391-1-stefanha@redhat.com> Signed-off-by: Julia Suvorova <jusual@mail.ru> --- Test will work if Joel's patches will use ARMv6-M. tests/Makefile.include | 2 ++ tests/tcg/arm/test-reserved-reg.c | 60 +++++++++++++++++++++++++++++++ 2 files changed, 62 insertions(+) create mode 100644 tests/tcg/arm/test-reserved-reg.c diff --git a/tests/Makefile.include b/tests/Makefile.include index d323c42682..8ab0b0d15f 100644 --- a/tests/Makefile.include +++ b/tests/Makefile.include @@ -387,6 +387,7 @@ gcov-files-arm-y += hw/timer/arm_mptimer.c check-qtest-arm-y += tests/boot-serial-test$(EXESUF) check-qtest-arm-y += tests/sdhci-test$(EXESUF) check-qtest-arm-y += tests/hexloader-test$(EXESUF) +check-qtest-arm-y += tests/tcg/arm/test-reserved-reg$(EXESUF) check-qtest-aarch64-y = tests/numa-test$(EXESUF) check-qtest-aarch64-y += tests/sdhci-test$(EXESUF) @@ -771,6 +772,7 @@ tests/device-introspect-test$(EXESUF): tests/device-introspect-test.o tests/rtc-test$(EXESUF): tests/rtc-test.o tests/m48t59-test$(EXESUF): tests/m48t59-test.o tests/hexloader-test$(EXESUF): tests/hexloader-test.o +tests/test-reserved-reg$(EXESUF): tests/tcg/arm/test-reserved-reg.o tests/endianness-test$(EXESUF): tests/endianness-test.o tests/spapr-phb-test$(EXESUF): tests/spapr-phb-test.o $(libqos-obj-y) tests/prom-env-test$(EXESUF): tests/prom-env-test.o $(libqos-obj-y) diff --git a/tests/tcg/arm/test-reserved-reg.c b/tests/tcg/arm/test-reserved-reg.c new file mode 100644 index 0000000000..97273ff24d --- /dev/null +++ b/tests/tcg/arm/test-reserved-reg.c @@ -0,0 +1,60 @@ +/* + * Test ARMv6-M SCS reserved registers + * + * Copyright (c) 2018 Julia Suvorova <jusual@mail.ru> + * + * This work is licensed under the terms of the GNU GPL, version 2 + * or later. See the COPYING file in the top-level directory. + */ + +#include "qemu/osdep.h" +#include "libqtest.h" + +static void test_reserved_reg(void) +{ + QTestState *s; + int i; + static const uint64_t reserved_reg[] = { 0xe000ed10, /* SCR */ + 0xe000ed18, /* SHPR1 */ + 0xe000ed28, /* CFSR */ + 0xe000ed2c, /* HFSR */ + 0xe000ed34, /* MMFAR */ + 0xe000ed38, /* BFAR */ + 0xe000ed3c, /* AFSR */ + 0xe000ed40, /* CPUID */ + 0xe000ed88, /* CPACR */ + 0xe000ef00 /* STIR */ }; + static const uint8_t mini_kernel[] = { 0x00, 0x00, 0x00, 0x00, + 0x09, 0x00, 0x00, 0x00 }; + ssize_t wlen, kernel_size = sizeof(mini_kernel); + int code_fd; + char codetmp[] = "/tmp/reserved-reg-test-XXXXXX"; + + code_fd = mkstemp(codetmp); + wlen = write(code_fd, mini_kernel, sizeof(mini_kernel)); + g_assert(wlen == kernel_size); + close(code_fd); + + s = qtest_startf("-kernel %s -M microbit -nographic", codetmp); + + for (i = 0; i < ARRAY_SIZE(reserved_reg); i++) { + int res; + qtest_writel(s, reserved_reg[i], 1); + res = qtest_readl(s, reserved_reg[i]); + g_assert(!res); + } + + qtest_quit(s); +} + +int main(int argc, char **argv) +{ + int ret; + + g_test_init(&argc, &argv, NULL); + + qtest_add_func("tcg/arm/test-reserved-reg", test_reserved_reg); + ret = g_test_run(); + + return ret; +} -- 2.17.1 ^ permalink raw reply related [flat|nested] 6+ messages in thread
end of thread, other threads:[~2018-07-05 12:07 UTC | newest] Thread overview: 6+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2018-07-04 19:58 [Qemu-devel] [PATCH 0/2] nvic: Handle ARMv6-M SCS reserved registers Julia Suvorova 2018-07-04 19:58 ` [Qemu-devel] [PATCH 1/2] " Julia Suvorova 2018-07-05 10:54 ` Peter Maydell 2018-07-05 11:25 ` Julia Suvorova 2018-07-05 12:06 ` Peter Maydell 2018-07-04 19:58 ` [Qemu-devel] [RFC 2/2] tests: Add ARMv6-M reserved register test Julia Suvorova
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).