From: <gregkh@linuxfoundation.org>
To: vincent_fann@realtek.com, Larry.Finger@lwfinger.net,
gregkh@linuxfoundation.org, kvalo@codeaurora.org,
shaofu@realtek.com
Cc: <stable@vger.kernel.org>, <stable-commits@vger.kernel.org>
Subject: Patch "rtlwifi: Remove the clear interrupt routine from all drivers" has been added to the 4.1-stable tree
Date: Wed, 29 Jul 2015 17:25:56 -0700 [thread overview]
Message-ID: <1438215956581@kroah.com> (raw)
This is a note to let you know that I've just added the patch titled
rtlwifi: Remove the clear interrupt routine from all drivers
to the 4.1-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
rtlwifi-remove-the-clear-interrupt-routine-from-all-drivers.patch
and it can be found in the queue-4.1 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.
>From 1277fa2ab2f9a624a4b0177119ca13b5fd65edd0 Mon Sep 17 00:00:00 2001
From: Vincent Fann <vincent_fann@realtek.com>
Date: Fri, 15 May 2015 21:29:27 -0500
Subject: rtlwifi: Remove the clear interrupt routine from all drivers
From: Vincent Fann <vincent_fann@realtek.com>
commit 1277fa2ab2f9a624a4b0177119ca13b5fd65edd0 upstream.
Several of these drivers have there TX randomly blocked for 3~5 seconds while
measuring tx throughput (iperf). The root couse happens in rtl_pci_flush().
The function uses a while-loop to wait for TX queue length to decrease to 0.
The TX queue length counts the number of packets that are queued in the driver.
The driver relys on the TX OK interrupt to return skb and reduce TX queue length.
The interrupt subroutine disables interupts, reads the interrupt registers, and
then clears the registers in the beginning of _rtl_pci_interrupt(). After all
interupts process are finished, the driver invokes enable_interrupt() to enable
interupts. This behavior is normal for an interrupt subroutine.
But enable_interrupt() invokes clear_interrupt() again. This unexpected interrupt
clearing may cleari me fresh TX OK interrupts. These missing interrupts cause TX
queue length to never reduce to 0i, which causes rtl_pci_flush() to be stuck in
unterminated while-loop.
This patch removes clear_interrupt() in enable_interrupt() to avoid this behavior.
Signed-off-by: Vincent Fann <vincent_fann@realtek.com>
Signed-off-by: Shao Fu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/net/wireless/rtlwifi/rtl8188ee/hw.c | 16 ----------------
drivers/net/wireless/rtlwifi/rtl8192ee/hw.c | 17 -----------------
drivers/net/wireless/rtlwifi/rtl8723ae/hw.c | 13 -------------
drivers/net/wireless/rtlwifi/rtl8723be/hw.c | 17 -----------------
drivers/net/wireless/rtlwifi/rtl8821ae/hw.c | 20 --------------------
5 files changed, 83 deletions(-)
--- a/drivers/net/wireless/rtlwifi/rtl8188ee/hw.c
+++ b/drivers/net/wireless/rtlwifi/rtl8188ee/hw.c
@@ -1354,27 +1354,11 @@ void rtl88ee_set_qos(struct ieee80211_hw
}
}
-static void rtl88ee_clear_interrupt(struct ieee80211_hw *hw)
-{
- struct rtl_priv *rtlpriv = rtl_priv(hw);
- u32 tmp;
-
- tmp = rtl_read_dword(rtlpriv, REG_HISR);
- rtl_write_dword(rtlpriv, REG_HISR, tmp);
-
- tmp = rtl_read_dword(rtlpriv, REG_HISRE);
- rtl_write_dword(rtlpriv, REG_HISRE, tmp);
-
- tmp = rtl_read_dword(rtlpriv, REG_HSISR);
- rtl_write_dword(rtlpriv, REG_HSISR, tmp);
-}
-
void rtl88ee_enable_interrupt(struct ieee80211_hw *hw)
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
- rtl88ee_clear_interrupt(hw);/*clear it here first*/
rtl_write_dword(rtlpriv, REG_HIMR,
rtlpci->irq_mask[0] & 0xFFFFFFFF);
rtl_write_dword(rtlpriv, REG_HIMRE,
--- a/drivers/net/wireless/rtlwifi/rtl8192ee/hw.c
+++ b/drivers/net/wireless/rtlwifi/rtl8192ee/hw.c
@@ -1584,28 +1584,11 @@ void rtl92ee_set_qos(struct ieee80211_hw
}
}
-static void rtl92ee_clear_interrupt(struct ieee80211_hw *hw)
-{
- struct rtl_priv *rtlpriv = rtl_priv(hw);
- u32 tmp;
-
- tmp = rtl_read_dword(rtlpriv, REG_HISR);
- rtl_write_dword(rtlpriv, REG_HISR, tmp);
-
- tmp = rtl_read_dword(rtlpriv, REG_HISRE);
- rtl_write_dword(rtlpriv, REG_HISRE, tmp);
-
- tmp = rtl_read_dword(rtlpriv, REG_HSISR);
- rtl_write_dword(rtlpriv, REG_HSISR, tmp);
-}
-
void rtl92ee_enable_interrupt(struct ieee80211_hw *hw)
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
- rtl92ee_clear_interrupt(hw);/*clear it here first*/
-
rtl_write_dword(rtlpriv, REG_HIMR, rtlpci->irq_mask[0] & 0xFFFFFFFF);
rtl_write_dword(rtlpriv, REG_HIMRE, rtlpci->irq_mask[1] & 0xFFFFFFFF);
rtlpci->irq_enabled = true;
--- a/drivers/net/wireless/rtlwifi/rtl8723ae/hw.c
+++ b/drivers/net/wireless/rtlwifi/rtl8723ae/hw.c
@@ -1258,18 +1258,6 @@ void rtl8723e_set_qos(struct ieee80211_h
}
}
-static void rtl8723e_clear_interrupt(struct ieee80211_hw *hw)
-{
- struct rtl_priv *rtlpriv = rtl_priv(hw);
- u32 tmp;
-
- tmp = rtl_read_dword(rtlpriv, REG_HISR);
- rtl_write_dword(rtlpriv, REG_HISR, tmp);
-
- tmp = rtl_read_dword(rtlpriv, REG_HISRE);
- rtl_write_dword(rtlpriv, REG_HISRE, tmp);
-}
-
void rtl8723e_enable_interrupt(struct ieee80211_hw *hw)
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
@@ -1284,7 +1272,6 @@ void rtl8723e_disable_interrupt(struct i
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
- rtl8723e_clear_interrupt(hw);/*clear it here first*/
rtl_write_dword(rtlpriv, 0x3a8, IMR8190_DISABLED);
rtl_write_dword(rtlpriv, 0x3ac, IMR8190_DISABLED);
rtlpci->irq_enabled = false;
--- a/drivers/net/wireless/rtlwifi/rtl8723be/hw.c
+++ b/drivers/net/wireless/rtlwifi/rtl8723be/hw.c
@@ -1634,28 +1634,11 @@ void rtl8723be_set_qos(struct ieee80211_
}
}
-static void rtl8723be_clear_interrupt(struct ieee80211_hw *hw)
-{
- struct rtl_priv *rtlpriv = rtl_priv(hw);
- u32 tmp;
-
- tmp = rtl_read_dword(rtlpriv, REG_HISR);
- rtl_write_dword(rtlpriv, REG_HISR, tmp);
-
- tmp = rtl_read_dword(rtlpriv, REG_HISRE);
- rtl_write_dword(rtlpriv, REG_HISRE, tmp);
-
- tmp = rtl_read_dword(rtlpriv, REG_HSISR);
- rtl_write_dword(rtlpriv, REG_HSISR, tmp);
-}
-
void rtl8723be_enable_interrupt(struct ieee80211_hw *hw)
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
- rtl8723be_clear_interrupt(hw);/*clear it here first*/
-
rtl_write_dword(rtlpriv, REG_HIMR, rtlpci->irq_mask[0] & 0xFFFFFFFF);
rtl_write_dword(rtlpriv, REG_HIMRE, rtlpci->irq_mask[1] & 0xFFFFFFFF);
rtlpci->irq_enabled = true;
--- a/drivers/net/wireless/rtlwifi/rtl8821ae/hw.c
+++ b/drivers/net/wireless/rtlwifi/rtl8821ae/hw.c
@@ -2253,31 +2253,11 @@ void rtl8821ae_set_qos(struct ieee80211_
}
}
-static void rtl8821ae_clear_interrupt(struct ieee80211_hw *hw)
-{
- struct rtl_priv *rtlpriv = rtl_priv(hw);
- u32 tmp;
- tmp = rtl_read_dword(rtlpriv, REG_HISR);
- /*printk("clear interrupt first:\n");
- printk("0x%x = 0x%08x\n",REG_HISR, tmp);*/
- rtl_write_dword(rtlpriv, REG_HISR, tmp);
-
- tmp = rtl_read_dword(rtlpriv, REG_HISRE);
- /*printk("0x%x = 0x%08x\n",REG_HISRE, tmp);*/
- rtl_write_dword(rtlpriv, REG_HISRE, tmp);
-
- tmp = rtl_read_dword(rtlpriv, REG_HSISR);
- /*printk("0x%x = 0x%08x\n",REG_HSISR, tmp);*/
- rtl_write_dword(rtlpriv, REG_HSISR, tmp);
-}
-
void rtl8821ae_enable_interrupt(struct ieee80211_hw *hw)
{
struct rtl_priv *rtlpriv = rtl_priv(hw);
struct rtl_pci *rtlpci = rtl_pcidev(rtl_pcipriv(hw));
- rtl8821ae_clear_interrupt(hw);/*clear it here first*/
-
rtl_write_dword(rtlpriv, REG_HIMR, rtlpci->irq_mask[0] & 0xFFFFFFFF);
rtl_write_dword(rtlpriv, REG_HIMRE, rtlpci->irq_mask[1] & 0xFFFFFFFF);
rtlpci->irq_enabled = true;
Patches currently in stable-queue which might be from vincent_fann@realtek.com are
queue-4.1/rtlwifi-remove-the-clear-interrupt-routine-from-all-drivers.patch
reply other threads:[~2015-07-30 0:26 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1438215956581@kroah.com \
--to=gregkh@linuxfoundation.org \
--cc=Larry.Finger@lwfinger.net \
--cc=kvalo@codeaurora.org \
--cc=shaofu@realtek.com \
--cc=stable-commits@vger.kernel.org \
--cc=stable@vger.kernel.org \
--cc=vincent_fann@realtek.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).