Patch "serial: 8250_pci: Add support for 16 port Exar boards" has been added to the 3.14-stable tree

[<gregkh@linuxfoundation.org>]

This is a note to let you know that I've just added the patch titled

    serial: 8250_pci: Add support for 16 port Exar boards

to the 3.14-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     serial-8250_pci-add-support-for-16-port-exar-boards.patch
and it can be found in the queue-3.14 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


>From 96a5d18bc1338786fecac73599f1681f59a59a8e Mon Sep 17 00:00:00 2001
From: Soeren Grunewald <soeren.grunewald@desy.de>
Date: Tue, 28 Apr 2015 16:29:49 +0200
Subject: serial: 8250_pci: Add support for 16 port Exar boards

From: Soeren Grunewald <soeren.grunewald@desy.de>

commit 96a5d18bc1338786fecac73599f1681f59a59a8e upstream.

The Exar XR17V358 chip usually provides only 8 ports. But two chips can be
combined to act as a single 16 port chip. Therefor one chip is configured
as master the second as slave by connecting the mode pin to VCC (master)
or GND (slave).

Then the master chip is reporting a different device-id depending on
whether a slave is detected or not. The UARTs 8-15 are addressed from
0x2000-0x3fff. So the offset of 0x400 from UART to UART can be used to
address all 16 ports as before.

See: https://www.exar.com/common/content/document.ashx?id=1587 page 11

Signed-off-by: Soeren Grunewald <soeren.grunewald@desy.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/tty/serial/8250/8250_pci.c |   25 +++++++++++++++++++++++--
 1 file changed, 23 insertions(+), 2 deletions(-)

--- a/drivers/tty/serial/8250/8250_pci.c
+++ b/drivers/tty/serial/8250/8250_pci.c
@@ -1772,6 +1772,8 @@ pci_wch_ch353_setup(struct serial_privat
 #define PCI_DEVICE_ID_SUNIX_1999	0x1999
 
 
+#define PCI_DEVICE_ID_EXAR_XR17V8358	0x8358
+
 /* Unknown vendors/cards - this should not be in linux/pci_ids.h */
 #define PCI_SUBDEVICE_ID_UNKNOWN_0x1584	0x1584
 #define PCI_SUBDEVICE_ID_UNKNOWN_0x1588	0x1588
@@ -2266,6 +2268,13 @@ static struct pci_serial_quirk pci_seria
 		.subdevice	= PCI_ANY_ID,
 		.setup		= pci_xr17v35x_setup,
 	},
+	{
+		.vendor = PCI_VENDOR_ID_EXAR,
+		.device = PCI_DEVICE_ID_EXAR_XR17V8358,
+		.subvendor	= PCI_ANY_ID,
+		.subdevice	= PCI_ANY_ID,
+		.setup		= pci_xr17v35x_setup,
+	},
 	/*
 	 * Xircom cards
 	 */
@@ -2706,6 +2715,7 @@ enum pci_board_num_t {
 	pbn_exar_XR17V352,
 	pbn_exar_XR17V354,
 	pbn_exar_XR17V358,
+	pbn_exar_XR17V8358,
 	pbn_exar_ibm_saturn,
 	pbn_pasemi_1682M,
 	pbn_ni8430_2,
@@ -3375,6 +3385,14 @@ static struct pciserial_board pci_boards
 		.reg_shift	= 0,
 		.first_offset	= 0,
 	},
+	[pbn_exar_XR17V8358] = {
+		.flags		= FL_BASE0,
+		.num_ports	= 16,
+		.base_baud	= 7812500,
+		.uart_offset	= 0x400,
+		.reg_shift	= 0,
+		.first_offset	= 0,
+	},
 	[pbn_exar_ibm_saturn] = {
 		.flags		= FL_BASE0,
 		.num_ports	= 1,
@@ -4731,7 +4749,7 @@ static struct pci_device_id serial_pci_t
 		0,
 		0, pbn_exar_XR17C158 },
 	/*
-	 * Exar Corp. XR17V35[248] Dual/Quad/Octal PCIe UARTs
+	 * Exar Corp. XR17V[48]35[248] Dual/Quad/Octal/Hexa PCIe UARTs
 	 */
 	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V352,
 		PCI_ANY_ID, PCI_ANY_ID,
@@ -4745,7 +4763,10 @@ static struct pci_device_id serial_pci_t
 		PCI_ANY_ID, PCI_ANY_ID,
 		0,
 		0, pbn_exar_XR17V358 },
-
+	{	PCI_VENDOR_ID_EXAR, PCI_DEVICE_ID_EXAR_XR17V8358,
+		PCI_ANY_ID, PCI_ANY_ID,
+		0,
+		0, pbn_exar_XR17V8358 },
 	/*
 	 * Topic TP560 Data/Fax/Voice 56k modem (reported by Evan Clarke)
 	 */


Patches currently in stable-queue which might be from soeren.grunewald@desy.de are

queue-3.14/serial-8250_pci-add-support-for-12-port-exar-boards.patch
queue-3.14/serial-8250_pci-add-support-for-16-port-exar-boards.patch