Patch "net: bcmgenet: Software reset EPHY after power on" has been added to the 4.3-stable tree

[<gregkh@linuxfoundation.org>]

This is a note to let you know that I've just added the patch titled

    net: bcmgenet: Software reset EPHY after power on

to the 4.3-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     net-bcmgenet-software-reset-ephy-after-power-on.patch
and it can be found in the queue-4.3 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


>From foo@baz Tue Nov 17 14:33:46 PST 2015
From: Florian Fainelli <f.fainelli@gmail.com>
Date: Thu, 29 Oct 2015 18:11:35 -0700
Subject: net: bcmgenet: Software reset EPHY after power on

From: Florian Fainelli <f.fainelli@gmail.com>

[ Upstream commit 5dbebbb44a6ad94aab2cd1a46f7676f255403f64 ]

The EPHY on GENET v1->v3 is extremely finicky, and will show occasional
failures based on the timing and reset sequence, ranging from duplicate
packets, to extremely high latencies.

Perform an additional software reset, and re-configuration to make sure it is
in a consistent and working state.

Fixes: 6ac3ce8295e6 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/broadcom/genet/bcmgenet.c |    4 +++-
 drivers/net/ethernet/broadcom/genet/bcmgenet.h |    1 +
 drivers/net/ethernet/broadcom/genet/bcmmii.c   |   18 ++++++++++++++++++
 3 files changed, 22 insertions(+), 1 deletion(-)

--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c
@@ -907,8 +907,10 @@ static void bcmgenet_power_up(struct bcm
 	}
 
 	bcmgenet_ext_writel(priv, reg, EXT_EXT_PWR_MGMT);
-	if (mode == GENET_POWER_PASSIVE)
+	if (mode == GENET_POWER_PASSIVE) {
 		bcmgenet_phy_power_set(priv->dev, true);
+		bcmgenet_mii_reset(priv->dev);
+	}
 }
 
 /* ioctl handle special commands that are not present in ethtool. */
--- a/drivers/net/ethernet/broadcom/genet/bcmgenet.h
+++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.h
@@ -674,6 +674,7 @@ int bcmgenet_mii_init(struct net_device
 int bcmgenet_mii_config(struct net_device *dev);
 int bcmgenet_mii_probe(struct net_device *dev);
 void bcmgenet_mii_exit(struct net_device *dev);
+void bcmgenet_mii_reset(struct net_device *dev);
 void bcmgenet_phy_power_set(struct net_device *dev, bool enable);
 void bcmgenet_mii_setup(struct net_device *dev);
 
--- a/drivers/net/ethernet/broadcom/genet/bcmmii.c
+++ b/drivers/net/ethernet/broadcom/genet/bcmmii.c
@@ -163,6 +163,7 @@ void bcmgenet_mii_setup(struct net_devic
 	phy_print_status(phydev);
 }
 
+
 static int bcmgenet_fixed_phy_link_update(struct net_device *dev,
 					  struct fixed_phy_status *status)
 {
@@ -172,6 +173,22 @@ static int bcmgenet_fixed_phy_link_updat
 	return 0;
 }
 
+/* Perform a voluntary PHY software reset, since the EPHY is very finicky about
+ * not doing it and will start corrupting packets
+ */
+void bcmgenet_mii_reset(struct net_device *dev)
+{
+	struct bcmgenet_priv *priv = netdev_priv(dev);
+
+	if (GENET_IS_V4(priv))
+		return;
+
+	if (priv->phydev) {
+		phy_init_hw(priv->phydev);
+		phy_start_aneg(priv->phydev);
+	}
+}
+
 void bcmgenet_phy_power_set(struct net_device *dev, bool enable)
 {
 	struct bcmgenet_priv *priv = netdev_priv(dev);
@@ -214,6 +231,7 @@ static void bcmgenet_internal_phy_setup(
 	reg = bcmgenet_ext_readl(priv, EXT_EXT_PWR_MGMT);
 	reg |= EXT_PWR_DN_EN_LD;
 	bcmgenet_ext_writel(priv, reg, EXT_EXT_PWR_MGMT);
+	bcmgenet_mii_reset(dev);
 }
 
 static void bcmgenet_moca_phy_setup(struct bcmgenet_priv *priv)


Patches currently in stable-queue which might be from f.fainelli@gmail.com are

queue-4.3/net-bcmgenet-software-reset-ephy-after-power-on.patch