From: <gregkh@linuxfoundation.org>
To: jonas@ludd.ltu.se, dnlplm@gmail.com, gregkh@linuxfoundation.org,
johan@kernel.org
Cc: <stable@vger.kernel.org>, <stable-commits@vger.kernel.org>
Subject: Patch "USB: cdc_acm: Ignore Infineon Flash Loader utility" has been added to the 3.10-stable tree
Date: Thu, 17 Dec 2015 15:55:33 -0800 [thread overview]
Message-ID: <145039653343206@kroah.com> (raw)
This is a note to let you know that I've just added the patch titled
USB: cdc_acm: Ignore Infineon Flash Loader utility
to the 3.10-stable tree which can be found at:
http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary
The filename of the patch is:
usb-cdc_acm-ignore-infineon-flash-loader-utility.patch
and it can be found in the queue-3.10 subdirectory.
If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.
>From f33a7f72e5fc033daccbb8d4753d7c5c41a4d67b Mon Sep 17 00:00:00 2001
From: Jonas Jonsson <jonas@ludd.ltu.se>
Date: Sun, 22 Nov 2015 11:47:17 +0100
Subject: USB: cdc_acm: Ignore Infineon Flash Loader utility
From: Jonas Jonsson <jonas@ludd.ltu.se>
commit f33a7f72e5fc033daccbb8d4753d7c5c41a4d67b upstream.
Some modems, such as the Telit UE910, are using an Infineon Flash Loader
utility. It has two interfaces, 2/2/0 (Abstract Modem) and 10/0/0 (CDC
Data). The latter can be used as a serial interface to upgrade the
firmware of the modem. However, that isn't possible when the cdc-acm
driver takes control of the device.
The following is an explanation of the behaviour by Daniele Palmas during
discussion on linux-usb.
"This is what happens when the device is turned on (without modifying
the drivers):
[155492.352031] usb 1-3: new high-speed USB device number 27 using ehci-pci
[155492.485429] usb 1-3: config 1 interface 0 altsetting 0 endpoint 0x81 has an invalid bInterval 255, changing to 11
[155492.485436] usb 1-3: New USB device found, idVendor=058b, idProduct=0041
[155492.485439] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[155492.485952] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
This is the flashing device that is caught by the cdc-acm driver. Once
the ttyACM appears, the application starts sending a magic string
(simple write on the file descriptor) to keep the device in flashing
mode. If this magic string is not properly received in a certain time
interval, the modem goes on in normal operative mode:
[155493.748094] usb 1-3: USB disconnect, device number 27
[155494.916025] usb 1-3: new high-speed USB device number 28 using ehci-pci
[155495.059978] usb 1-3: New USB device found, idVendor=1bc7, idProduct=0021
[155495.059983] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[155495.059986] usb 1-3: Product: 6 CDC-ACM + 1 CDC-ECM
[155495.059989] usb 1-3: Manufacturer: Telit
[155495.059992] usb 1-3: SerialNumber: 359658044004697
[155495.138958] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
[155495.140832] cdc_acm 1-3:1.2: ttyACM1: USB ACM device
[155495.142827] cdc_acm 1-3:1.4: ttyACM2: USB ACM device
[155495.144462] cdc_acm 1-3:1.6: ttyACM3: USB ACM device
[155495.145967] cdc_acm 1-3:1.8: ttyACM4: USB ACM device
[155495.147588] cdc_acm 1-3:1.10: ttyACM5: USB ACM device
[155495.154322] cdc_ether 1-3:1.12 wwan0: register 'cdc_ether' at usb-0000:00:1a.7-3, Mobile Broadband Network Device, 00:00:11:12:13:14
Using the cdc-acm driver, the string, though being sent in the same way
than using the usb-serial-simple driver (I can confirm that the data is
passing properly since I used an hw usb sniffer), does not make the
device to stay in flashing mode."
Signed-off-by: Jonas Jonsson <jonas@ludd.ltu.se>
Tested-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/usb/class/cdc-acm.c | 5 +++++
1 file changed, 5 insertions(+)
--- a/drivers/usb/class/cdc-acm.c
+++ b/drivers/usb/class/cdc-acm.c
@@ -1726,6 +1726,11 @@ static const struct usb_device_id acm_id
},
#endif
+ /* Exclude Infineon Flash Loader utility */
+ { USB_DEVICE(0x058b, 0x0041),
+ .driver_info = IGNORE_DEVICE,
+ },
+
/* control interfaces without any protocol set */
{ USB_INTERFACE_INFO(USB_CLASS_COMM, USB_CDC_SUBCLASS_ACM,
USB_CDC_PROTO_NONE) },
Patches currently in stable-queue which might be from jonas@ludd.ltu.se are
queue-3.10/usb-cdc_acm-ignore-infineon-flash-loader-utility.patch
reply other threads:[~2015-12-17 23:55 UTC|newest]
Thread overview: [no followups] expand[flat|nested] mbox.gz Atom feed
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=145039653343206@kroah.com \
--to=gregkh@linuxfoundation.org \
--cc=dnlplm@gmail.com \
--cc=johan@kernel.org \
--cc=jonas@ludd.ltu.se \
--cc=stable-commits@vger.kernel.org \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).