Patch "ath10k: add BMI parameters to fix calibration from DT/pre-cal" has been added to the 4.9-stable tree

Patch "ath10k: add BMI parameters to fix calibration from DT/pre-cal" has been added to the 4.9-stable tree

[gregkh]

This is a note to let you know that I've just added the patch titled

    ath10k: add BMI parameters to fix calibration from DT/pre-cal

to the 4.9-stable tree which can be found at:
    http://www.kernel.org/git/?p=linux/kernel/git/stable/stable-queue.git;a=summary

The filename of the patch is:
     ath10k-add-bmi-parameters-to-fix-calibration-from-dt-pre-cal.patch
and it can be found in the queue-4.9 subdirectory.

If you, or anyone else, feels it should not be added to the stable tree,
please let <stable@vger.kernel.org> know about it.


>From foo@baz Mon Apr  9 17:09:24 CEST 2018
From: Anilkumar Kolli <akolli@qti.qualcomm.com>
Date: Wed, 31 May 2017 14:21:27 +0300
Subject: ath10k: add BMI parameters to fix calibration from DT/pre-cal

From: Anilkumar Kolli <akolli@qti.qualcomm.com>


[ Upstream commit a9f5f287fa1d47d61dfa8b60f94831174b2ea4d0 ]

QCA99X0, QCA9888, QCA9984 supports calibration data in
either OTP or DT/pre-cal file. Current ath10k supports
Calibration data from OTP only.

If caldata is loaded from DT/pre-cal file, fetching board id
and applying calibration parameters like tx power gets failed.

error log:
[   15.733663] ath10k_pci 0000:01:00.0: failed to fetch board file: -2
[   15.741474] ath10k_pci 0000:01:00.0: could not probe fw (-2)

This patch adds calibration data support from DT/pre-cal
file.  Below parameters are used to get board id and
applying calibration parameters from cal data.

		EEPROM[OTP]	FLASH[DT/pre-cal file]
Cal param	0x700		0x10000
Board id	0x10		0x8000

Tested on QCA9888 with pre-cal file.

Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/wireless/ath/ath10k/bmi.h  |    2 ++
 drivers/net/wireless/ath/ath10k/core.c |   16 +++++++++++++---
 2 files changed, 15 insertions(+), 3 deletions(-)

--- a/drivers/net/wireless/ath/ath10k/bmi.h
+++ b/drivers/net/wireless/ath/ath10k/bmi.h
@@ -83,6 +83,8 @@ enum bmi_cmd_id {
 #define BMI_NVRAM_SEG_NAME_SZ 16
 
 #define BMI_PARAM_GET_EEPROM_BOARD_ID 0x10
+#define BMI_PARAM_GET_FLASH_BOARD_ID 0x8000
+#define BMI_PARAM_FLASH_SECTION_ALL 0x10000
 
 #define ATH10K_BMI_BOARD_ID_FROM_OTP_MASK   0x7c00
 #define ATH10K_BMI_BOARD_ID_FROM_OTP_LSB    10
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -652,7 +652,7 @@ static int ath10k_core_get_board_id_from
 {
 	u32 result, address;
 	u8 board_id, chip_id;
-	int ret;
+	int ret, bmi_board_id_param;
 
 	address = ar->hw_params.patch_load_addr;
 
@@ -676,8 +676,13 @@ static int ath10k_core_get_board_id_from
 		return ret;
 	}
 
-	ret = ath10k_bmi_execute(ar, address, BMI_PARAM_GET_EEPROM_BOARD_ID,
-				 &result);
+	if (ar->cal_mode == ATH10K_PRE_CAL_MODE_DT ||
+	    ar->cal_mode == ATH10K_PRE_CAL_MODE_FILE)
+		bmi_board_id_param = BMI_PARAM_GET_FLASH_BOARD_ID;
+	else
+		bmi_board_id_param = BMI_PARAM_GET_EEPROM_BOARD_ID;
+
+	ret = ath10k_bmi_execute(ar, address, bmi_board_id_param, &result);
 	if (ret) {
 		ath10k_err(ar, "could not execute otp for board id check: %d\n",
 			   ret);
@@ -739,6 +744,11 @@ static int ath10k_download_and_run_otp(s
 		return ret;
 	}
 
+	/* As of now pre-cal is valid for 10_4 variants */
+	if (ar->cal_mode == ATH10K_PRE_CAL_MODE_DT ||
+	    ar->cal_mode == ATH10K_PRE_CAL_MODE_FILE)
+		bmi_otp_exe_param = BMI_PARAM_FLASH_SECTION_ALL;
+
 	ret = ath10k_bmi_execute(ar, address, bmi_otp_exe_param, &result);
 	if (ret) {
 		ath10k_err(ar, "could not execute otp (%d)\n", ret);


Patches currently in stable-queue which might be from akolli@qti.qualcomm.com are

queue-4.9/ath10k-add-bmi-parameters-to-fix-calibration-from-dt-pre-cal.patch