[PATCH 3.10 07/71] spi: omap2-mcspi: Configure hardware when slave driver changes mode

[Greg Kroah-Hartman <gregkh@linuxfoundation.org>]

3.10-stable review patch.  If anyone has any objections, please let me know.

------------------

From: "Mark A. Greer" <mgreer@animalcreek.com>

commit 97ca0d6cc118716840ea443e010cb3d5f2d25eaf upstream.

Commit id 2bd16e3e23d9df41592c6b257c59b6860a9cc3ea
(spi: omap2-mcspi: Do not configure the controller
on each transfer unless needed) does its job too
well so omap2_mcspi_setup_transfer() isn't called
even when an SPI slave driver changes 'spi->mode'.
The result is that the mode requested by the SPI
slave driver never takes effect.

Fix this by adding the 'mode' member to the
omap2_mcspi_cs structure which holds the mode
value that the hardware is configured for.
When the SPI slave driver changes 'spi->mode'
it will be different than the value of this new
member and the SPI master driver will know that
the hardware must be reconfigured (by calling
omap2_mcspi_setup_transfer()).

Fixes: 2bd16e3e23 (spi: omap2-mcspi: Do not configure the controller on each transfer unless needed)
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/spi/spi-omap2-mcspi.c |   14 ++++++++++++++
 1 file changed, 14 insertions(+)

--- a/drivers/spi/spi-omap2-mcspi.c
+++ b/drivers/spi/spi-omap2-mcspi.c
@@ -136,6 +136,7 @@ struct omap2_mcspi_cs {
 	void __iomem		*base;
 	unsigned long		phys;
 	int			word_len;
+	u16			mode;
 	struct list_head	node;
 	/* Context save and restore shadow register */
 	u32			chconf0;
@@ -801,6 +802,8 @@ static int omap2_mcspi_setup_transfer(st
 
 	mcspi_write_chconf0(spi, l);
 
+	cs->mode = spi->mode;
+
 	dev_dbg(&spi->dev, "setup: speed %d, sample %s edge, clk %s\n",
 			OMAP2_MCSPI_MAX_FREQ >> div,
 			(spi->mode & SPI_CPHA) ? "trailing" : "leading",
@@ -871,6 +874,7 @@ static int omap2_mcspi_setup(struct spi_
 			return -ENOMEM;
 		cs->base = mcspi->base + spi->chip_select * 0x14;
 		cs->phys = mcspi->phys + spi->chip_select * 0x14;
+		cs->mode = 0;
 		cs->chconf0 = 0;
 		spi->controller_state = cs;
 		/* Link this to context save list */
@@ -1043,6 +1047,16 @@ static void omap2_mcspi_work(struct omap
 			mcspi_read_cs_reg(spi, OMAP2_MCSPI_MODULCTRL);
 	}
 
+	/*
+	 * The slave driver could have changed spi->mode in which case
+	 * it will be different from cs->mode (the current hardware setup).
+	 * If so, set par_override (even though its not a parity issue) so
+	 * omap2_mcspi_setup_transfer will be called to configure the hardware
+	 * with the correct mode on the first iteration of the loop below.
+	 */
+	if (spi->mode != cs->mode)
+		par_override = 1;
+
 	omap2_mcspi_set_enable(spi, 0);
 
 	m->status = status;