* [PATCH 3.10 01/16] myri10ge: check for DMA mapping errors
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
@ 2014-10-13 2:23 ` Greg Kroah-Hartman
2014-10-13 2:23 ` [PATCH 3.10 02/16] sit: Fix ipip6_tunnel_lookup device matching criteria Greg Kroah-Hartman
` (16 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:23 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, Stanislaw Gruszka, David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Stanislaw Gruszka <sgruszka@redhat.com>
[ Upstream commit 10545937e866ccdbb7ab583031dbdcc6b14e4eb4 ]
On IOMMU systems DMA mapping can fail, we need to check for
that possibility.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/net/ethernet/myricom/myri10ge/myri10ge.c | 88 +++++++++++++++--------
1 file changed, 58 insertions(+), 30 deletions(-)
--- a/drivers/net/ethernet/myricom/myri10ge/myri10ge.c
+++ b/drivers/net/ethernet/myricom/myri10ge/myri10ge.c
@@ -856,6 +856,10 @@ static int myri10ge_dma_test(struct myri
return -ENOMEM;
dmatest_bus = pci_map_page(mgp->pdev, dmatest_page, 0, PAGE_SIZE,
DMA_BIDIRECTIONAL);
+ if (unlikely(pci_dma_mapping_error(mgp->pdev, dmatest_bus))) {
+ __free_page(dmatest_page);
+ return -ENOMEM;
+ }
/* Run a small DMA test.
* The magic multipliers to the length tell the firmware
@@ -1191,6 +1195,7 @@ myri10ge_alloc_rx_pages(struct myri10ge_
int bytes, int watchdog)
{
struct page *page;
+ dma_addr_t bus;
int idx;
#if MYRI10GE_ALLOC_SIZE > 4096
int end_offset;
@@ -1215,11 +1220,21 @@ myri10ge_alloc_rx_pages(struct myri10ge_
rx->watchdog_needed = 1;
return;
}
+
+ bus = pci_map_page(mgp->pdev, page, 0,
+ MYRI10GE_ALLOC_SIZE,
+ PCI_DMA_FROMDEVICE);
+ if (unlikely(pci_dma_mapping_error(mgp->pdev, bus))) {
+ __free_pages(page, MYRI10GE_ALLOC_ORDER);
+ if (rx->fill_cnt - rx->cnt < 16)
+ rx->watchdog_needed = 1;
+ return;
+ }
+
rx->page = page;
rx->page_offset = 0;
- rx->bus = pci_map_page(mgp->pdev, page, 0,
- MYRI10GE_ALLOC_SIZE,
- PCI_DMA_FROMDEVICE);
+ rx->bus = bus;
+
}
rx->info[idx].page = rx->page;
rx->info[idx].page_offset = rx->page_offset;
@@ -2576,6 +2591,35 @@ myri10ge_submit_req(struct myri10ge_tx_b
mb();
}
+static void myri10ge_unmap_tx_dma(struct myri10ge_priv *mgp,
+ struct myri10ge_tx_buf *tx, int idx)
+{
+ unsigned int len;
+ int last_idx;
+
+ /* Free any DMA resources we've alloced and clear out the skb slot */
+ last_idx = (idx + 1) & tx->mask;
+ idx = tx->req & tx->mask;
+ do {
+ len = dma_unmap_len(&tx->info[idx], len);
+ if (len) {
+ if (tx->info[idx].skb != NULL)
+ pci_unmap_single(mgp->pdev,
+ dma_unmap_addr(&tx->info[idx],
+ bus), len,
+ PCI_DMA_TODEVICE);
+ else
+ pci_unmap_page(mgp->pdev,
+ dma_unmap_addr(&tx->info[idx],
+ bus), len,
+ PCI_DMA_TODEVICE);
+ dma_unmap_len_set(&tx->info[idx], len, 0);
+ tx->info[idx].skb = NULL;
+ }
+ idx = (idx + 1) & tx->mask;
+ } while (idx != last_idx);
+}
+
/*
* Transmit a packet. We need to split the packet so that a single
* segment does not cross myri10ge->tx_boundary, so this makes segment
@@ -2599,7 +2643,7 @@ static netdev_tx_t myri10ge_xmit(struct
u32 low;
__be32 high_swapped;
unsigned int len;
- int idx, last_idx, avail, frag_cnt, frag_idx, count, mss, max_segments;
+ int idx, avail, frag_cnt, frag_idx, count, mss, max_segments;
u16 pseudo_hdr_offset, cksum_offset, queue;
int cum_len, seglen, boundary, rdma_count;
u8 flags, odd_flag;
@@ -2696,9 +2740,12 @@ again:
/* map the skb for DMA */
len = skb_headlen(skb);
+ bus = pci_map_single(mgp->pdev, skb->data, len, PCI_DMA_TODEVICE);
+ if (unlikely(pci_dma_mapping_error(mgp->pdev, bus)))
+ goto drop;
+
idx = tx->req & tx->mask;
tx->info[idx].skb = skb;
- bus = pci_map_single(mgp->pdev, skb->data, len, PCI_DMA_TODEVICE);
dma_unmap_addr_set(&tx->info[idx], bus, bus);
dma_unmap_len_set(&tx->info[idx], len, len);
@@ -2797,12 +2844,16 @@ again:
break;
/* map next fragment for DMA */
- idx = (count + tx->req) & tx->mask;
frag = &skb_shinfo(skb)->frags[frag_idx];
frag_idx++;
len = skb_frag_size(frag);
bus = skb_frag_dma_map(&mgp->pdev->dev, frag, 0, len,
DMA_TO_DEVICE);
+ if (unlikely(pci_dma_mapping_error(mgp->pdev, bus))) {
+ myri10ge_unmap_tx_dma(mgp, tx, idx);
+ goto drop;
+ }
+ idx = (count + tx->req) & tx->mask;
dma_unmap_addr_set(&tx->info[idx], bus, bus);
dma_unmap_len_set(&tx->info[idx], len, len);
}
@@ -2833,31 +2884,8 @@ again:
return NETDEV_TX_OK;
abort_linearize:
- /* Free any DMA resources we've alloced and clear out the skb
- * slot so as to not trip up assertions, and to avoid a
- * double-free if linearizing fails */
+ myri10ge_unmap_tx_dma(mgp, tx, idx);
- last_idx = (idx + 1) & tx->mask;
- idx = tx->req & tx->mask;
- tx->info[idx].skb = NULL;
- do {
- len = dma_unmap_len(&tx->info[idx], len);
- if (len) {
- if (tx->info[idx].skb != NULL)
- pci_unmap_single(mgp->pdev,
- dma_unmap_addr(&tx->info[idx],
- bus), len,
- PCI_DMA_TODEVICE);
- else
- pci_unmap_page(mgp->pdev,
- dma_unmap_addr(&tx->info[idx],
- bus), len,
- PCI_DMA_TODEVICE);
- dma_unmap_len_set(&tx->info[idx], len, 0);
- tx->info[idx].skb = NULL;
- }
- idx = (idx + 1) & tx->mask;
- } while (idx != last_idx);
if (skb_is_gso(skb)) {
netdev_err(mgp->dev, "TSO but wanted to linearize?!?!?\n");
goto drop;
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 02/16] sit: Fix ipip6_tunnel_lookup device matching criteria
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
2014-10-13 2:23 ` [PATCH 3.10 01/16] myri10ge: check for DMA mapping errors Greg Kroah-Hartman
@ 2014-10-13 2:23 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 03/16] tcp: fix tcp_release_cb() to dispatch via address family for mtu_reduced() Greg Kroah-Hartman
` (15 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:23 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, Shmulik Ladkani, Nicolas Dichtel,
David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Shmulik Ladkani <shmulik.ladkani@gmail.com>
[ Upstream commit bc8fc7b8f825ef17a0fb9e68c18ce94fa66ab337 ]
As of 4fddbf5d78 ("sit: strictly restrict incoming traffic to tunnel link device"),
when looking up a tunnel, tunnel's underlying interface (t->parms.link)
is verified to match incoming traffic's ingress device.
However the comparison was incorrectly based on skb->dev->iflink.
Instead, dev->ifindex should be used, which correctly represents the
interface from which the IP stack hands the ipip6 packets.
This allows setting up sit tunnels bound to vlan interfaces (otherwise
incoming ipip6 traffic on the vlan interface was dropped due to
ipip6_tunnel_lookup match failure).
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
net/ipv6/sit.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
--- a/net/ipv6/sit.c
+++ b/net/ipv6/sit.c
@@ -101,19 +101,19 @@ static struct ip_tunnel *ipip6_tunnel_lo
for_each_ip_tunnel_rcu(t, sitn->tunnels_r_l[h0 ^ h1]) {
if (local == t->parms.iph.saddr &&
remote == t->parms.iph.daddr &&
- (!dev || !t->parms.link || dev->iflink == t->parms.link) &&
+ (!dev || !t->parms.link || dev->ifindex == t->parms.link) &&
(t->dev->flags & IFF_UP))
return t;
}
for_each_ip_tunnel_rcu(t, sitn->tunnels_r[h0]) {
if (remote == t->parms.iph.daddr &&
- (!dev || !t->parms.link || dev->iflink == t->parms.link) &&
+ (!dev || !t->parms.link || dev->ifindex == t->parms.link) &&
(t->dev->flags & IFF_UP))
return t;
}
for_each_ip_tunnel_rcu(t, sitn->tunnels_l[h1]) {
if (local == t->parms.iph.saddr &&
- (!dev || !t->parms.link || dev->iflink == t->parms.link) &&
+ (!dev || !t->parms.link || dev->ifindex == t->parms.link) &&
(t->dev->flags & IFF_UP))
return t;
}
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 03/16] tcp: fix tcp_release_cb() to dispatch via address family for mtu_reduced()
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
2014-10-13 2:23 ` [PATCH 3.10 01/16] myri10ge: check for DMA mapping errors Greg Kroah-Hartman
2014-10-13 2:23 ` [PATCH 3.10 02/16] sit: Fix ipip6_tunnel_lookup device matching criteria Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 04/16] packet: handle too big packets for PACKET_V3 Greg Kroah-Hartman
` (14 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, Neal Cardwell, Eric Dumazet,
Hannes Frederic Sowa, David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Neal Cardwell <ncardwell@google.com>
[ Upstream commit 4fab9071950c2021d846e18351e0f46a1cffd67b ]
Make sure we use the correct address-family-specific function for
handling MTU reductions from within tcp_release_cb().
Previously AF_INET6 sockets were incorrectly always using the IPv6
code path when sometimes they were handling IPv4 traffic and thus had
an IPv4 dst.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Diagnosed-by: Willem de Bruijn <willemb@google.com>
Fixes: 563d34d057862 ("tcp: dont drop MTU reduction indications")
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
include/net/inet_connection_sock.h | 1 +
include/net/sock.h | 1 -
include/net/tcp.h | 1 +
net/ipv4/tcp_ipv4.c | 5 +++--
net/ipv4/tcp_output.c | 2 +-
net/ipv6/tcp_ipv6.c | 3 ++-
6 files changed, 8 insertions(+), 5 deletions(-)
--- a/include/net/inet_connection_sock.h
+++ b/include/net/inet_connection_sock.h
@@ -62,6 +62,7 @@ struct inet_connection_sock_af_ops {
void (*addr2sockaddr)(struct sock *sk, struct sockaddr *);
int (*bind_conflict)(const struct sock *sk,
const struct inet_bind_bucket *tb, bool relax);
+ void (*mtu_reduced)(struct sock *sk);
};
/** inet_connection_sock - INET connection oriented sock
--- a/include/net/sock.h
+++ b/include/net/sock.h
@@ -932,7 +932,6 @@ struct proto {
struct sk_buff *skb);
void (*release_cb)(struct sock *sk);
- void (*mtu_reduced)(struct sock *sk);
/* Keeping track of sk's, looking them up, and port selection methods. */
void (*hash)(struct sock *sk);
--- a/include/net/tcp.h
+++ b/include/net/tcp.h
@@ -460,6 +460,7 @@ extern const u8 *tcp_parse_md5sig_option
*/
extern void tcp_v4_send_check(struct sock *sk, struct sk_buff *skb);
+void tcp_v4_mtu_reduced(struct sock *sk);
extern int tcp_v4_conn_request(struct sock *sk, struct sk_buff *skb);
extern struct sock * tcp_create_openreq_child(struct sock *sk,
struct request_sock *req,
--- a/net/ipv4/tcp_ipv4.c
+++ b/net/ipv4/tcp_ipv4.c
@@ -268,7 +268,7 @@ EXPORT_SYMBOL(tcp_v4_connect);
* It can be called through tcp_release_cb() if socket was owned by user
* at the time tcp_v4_err() was called to handle ICMP message.
*/
-static void tcp_v4_mtu_reduced(struct sock *sk)
+void tcp_v4_mtu_reduced(struct sock *sk)
{
struct dst_entry *dst;
struct inet_sock *inet = inet_sk(sk);
@@ -298,6 +298,7 @@ static void tcp_v4_mtu_reduced(struct so
tcp_simple_retransmit(sk);
} /* else let the usual retransmit timer handle it */
}
+EXPORT_SYMBOL(tcp_v4_mtu_reduced);
static void do_redirect(struct sk_buff *skb, struct sock *sk)
{
@@ -2142,6 +2143,7 @@ const struct inet_connection_sock_af_ops
.compat_setsockopt = compat_ip_setsockopt,
.compat_getsockopt = compat_ip_getsockopt,
#endif
+ .mtu_reduced = tcp_v4_mtu_reduced,
};
EXPORT_SYMBOL(ipv4_specific);
@@ -2867,7 +2869,6 @@ struct proto tcp_prot = {
.sendpage = tcp_sendpage,
.backlog_rcv = tcp_v4_do_rcv,
.release_cb = tcp_release_cb,
- .mtu_reduced = tcp_v4_mtu_reduced,
.hash = inet_hash,
.unhash = inet_unhash,
.get_port = inet_csk_get_port,
--- a/net/ipv4/tcp_output.c
+++ b/net/ipv4/tcp_output.c
@@ -775,7 +775,7 @@ void tcp_release_cb(struct sock *sk)
__sock_put(sk);
}
if (flags & (1UL << TCP_MTU_REDUCED_DEFERRED)) {
- sk->sk_prot->mtu_reduced(sk);
+ inet_csk(sk)->icsk_af_ops->mtu_reduced(sk);
__sock_put(sk);
}
}
--- a/net/ipv6/tcp_ipv6.c
+++ b/net/ipv6/tcp_ipv6.c
@@ -1651,6 +1651,7 @@ static const struct inet_connection_sock
.compat_setsockopt = compat_ipv6_setsockopt,
.compat_getsockopt = compat_ipv6_getsockopt,
#endif
+ .mtu_reduced = tcp_v6_mtu_reduced,
};
#ifdef CONFIG_TCP_MD5SIG
@@ -1682,6 +1683,7 @@ static const struct inet_connection_sock
.compat_setsockopt = compat_ipv6_setsockopt,
.compat_getsockopt = compat_ipv6_getsockopt,
#endif
+ .mtu_reduced = tcp_v4_mtu_reduced,
};
#ifdef CONFIG_TCP_MD5SIG
@@ -1919,7 +1921,6 @@ struct proto tcpv6_prot = {
.sendpage = tcp_sendpage,
.backlog_rcv = tcp_v6_do_rcv,
.release_cb = tcp_release_cb,
- .mtu_reduced = tcp_v6_mtu_reduced,
.hash = tcp_v6_hash,
.unhash = inet_unhash,
.get_port = inet_csk_get_port,
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 04/16] packet: handle too big packets for PACKET_V3
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (2 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 03/16] tcp: fix tcp_release_cb() to dispatch via address family for mtu_reduced() Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 05/16] openvswitch: fix panic with multiple vlan headers Greg Kroah-Hartman
` (13 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, Eric Dumazet, Daniel Borkmann,
Neil Horman, David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Eric Dumazet <edumazet@google.com>
[ Upstream commit dc808110bb62b64a448696ecac3938902c92e1ab ]
af_packet can currently overwrite kernel memory by out of bound
accesses, because it assumed a [new] block can always hold one frame.
This is not generally the case, even if most existing tools do it right.
This patch clamps too long frames as API permits, and issue a one time
error on syslog.
[ 394.357639] tpacket_rcv: packet too big, clamped from 5042 to 3966. macoff=82
In this example, packet header tp_snaplen was set to 3966,
and tp_len was set to 5042 (skb->len)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: f6fb8f100b80 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
net/packet/af_packet.c | 17 +++++++++++++++++
net/packet/internal.h | 1 +
2 files changed, 18 insertions(+)
--- a/net/packet/af_packet.c
+++ b/net/packet/af_packet.c
@@ -565,6 +565,7 @@ static void init_prb_bdqc(struct packet_
p1->tov_in_jiffies = msecs_to_jiffies(p1->retire_blk_tov);
p1->blk_sizeof_priv = req_u->req3.tp_sizeof_priv;
+ p1->max_frame_len = p1->kblk_size - BLK_PLUS_PRIV(p1->blk_sizeof_priv);
prb_init_ft_ops(p1, req_u);
prb_setup_retire_blk_timer(po, tx_ring);
prb_open_block(p1, pbd);
@@ -1803,6 +1804,18 @@ static int tpacket_rcv(struct sk_buff *s
if ((int)snaplen < 0)
snaplen = 0;
}
+ } else if (unlikely(macoff + snaplen >
+ GET_PBDQC_FROM_RB(&po->rx_ring)->max_frame_len)) {
+ u32 nval;
+
+ nval = GET_PBDQC_FROM_RB(&po->rx_ring)->max_frame_len - macoff;
+ pr_err_once("tpacket_rcv: packet too big, clamped from %u to %u. macoff=%u\n",
+ snaplen, nval, macoff);
+ snaplen = nval;
+ if (unlikely((int)snaplen < 0)) {
+ snaplen = 0;
+ macoff = GET_PBDQC_FROM_RB(&po->rx_ring)->max_frame_len;
+ }
}
spin_lock(&sk->sk_receive_queue.lock);
h.raw = packet_current_rx_frame(po, skb,
@@ -3642,6 +3655,10 @@ static int packet_set_ring(struct sock *
goto out;
if (unlikely(req->tp_block_size & (PAGE_SIZE - 1)))
goto out;
+ if (po->tp_version >= TPACKET_V3 &&
+ (int)(req->tp_block_size -
+ BLK_PLUS_PRIV(req_u->req3.tp_sizeof_priv)) <= 0)
+ goto out;
if (unlikely(req->tp_frame_size < po->tp_hdrlen +
po->tp_reserve))
goto out;
--- a/net/packet/internal.h
+++ b/net/packet/internal.h
@@ -29,6 +29,7 @@ struct tpacket_kbdq_core {
char *pkblk_start;
char *pkblk_end;
int kblk_size;
+ unsigned int max_frame_len;
unsigned int knum_blocks;
uint64_t knxt_seq_num;
char *prev;
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 05/16] openvswitch: fix panic with multiple vlan headers
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (3 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 04/16] packet: handle too big packets for PACKET_V3 Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 06/16] l2tp: fix race while getting PMTU on PPP pseudo-wire Greg Kroah-Hartman
` (12 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, Yulong Pei, Jiri Benc,
David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Jiri Benc <jbenc@redhat.com>
[ Upstream commit 2ba5af42a7b59ef01f9081234d8855140738defd ]
When there are multiple vlan headers present in a received frame, the first
one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the
skb beyond the VLAN TPID may be still non-linear, including the inner TCI
and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it
does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is
executed, __pop_vlan_tci pulls the next vlan header into vlan_tci.
This leads to two things:
1. Part of the resulting ethernet header is in the non-linear part of the
skb. When eth_type_trans is called later as the result of
OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci
is in fact accessing random data when it reads past the TPID.
2. network_header points into the ethernet header instead of behind it.
mac_len is set to a wrong value (10), too.
Reported-by: Yulong Pei <ypei@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
net/openvswitch/actions.c | 5 +++++
1 file changed, 5 insertions(+)
--- a/net/openvswitch/actions.c
+++ b/net/openvswitch/actions.c
@@ -40,6 +40,9 @@ static int do_execute_actions(struct dat
static int make_writable(struct sk_buff *skb, int write_len)
{
+ if (!pskb_may_pull(skb, write_len))
+ return -ENOMEM;
+
if (!skb_cloned(skb) || skb_clone_writable(skb, write_len))
return 0;
@@ -68,6 +71,8 @@ static int __pop_vlan_tci(struct sk_buff
vlan_set_encap_proto(skb, vhdr);
skb->mac_header += VLAN_HLEN;
+ if (skb_network_offset(skb) < ETH_HLEN)
+ skb_set_network_header(skb, ETH_HLEN);
skb_reset_mac_len(skb);
return 0;
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 06/16] l2tp: fix race while getting PMTU on PPP pseudo-wire
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (4 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 05/16] openvswitch: fix panic with multiple vlan headers Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 07/16] tg3: Work around HW/FW limitations with vlan encapsulated frames Greg Kroah-Hartman
` (11 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, Guillaume Nault, Eric Dumazet,
David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Guillaume Nault <g.nault@alphalink.fr>
[ Upstream commit eed4d839b0cdf9d84b0a9bc63de90fd5e1e886fb ]
Use dst_entry held by sk_dst_get() to retrieve tunnel's PMTU.
The dst_mtu(__sk_dst_get(tunnel->sock)) call was racy. __sk_dst_get()
could return NULL if tunnel->sock->sk_dst_cache was reset just before the
call, thus making dst_mtu() dereference a NULL pointer:
[ 1937.661598] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[ 1937.664005] IP: [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp]
[ 1937.664005] PGD daf0c067 PUD d9f93067 PMD 0
[ 1937.664005] Oops: 0000 [#1] SMP
[ 1937.664005] Modules linked in: l2tp_ppp l2tp_netlink l2tp_core ip6table_filter ip6_tables iptable_filter ip_tables ebtable_nat ebtables x_tables udp_tunnel pppoe pppox ppp_generic slhc deflate ctr twofish_generic twofish_x86_64_3way xts lrw gf128mul glue_helper twofish_x86_64 twofish_common blowfish_generic blowfish_x86_64 blowfish_common des_generic cbc xcbc rmd160 sha512_generic hmac crypto_null af_key xfrm_algo 8021q garp bridge stp llc tun atmtcp clip atm ext3 mbcache jbd iTCO_wdt coretemp kvm_intel iTCO_vendor_support kvm pcspkr evdev ehci_pci lpc_ich mfd_core i5400_edac edac_core i5k_amb shpchp button processor thermal_sys xfs crc32c_generic libcrc32c dm_mod usbhid sg hid sr_mod sd_mod cdrom crc_t10dif crct10dif_common ata_generic ahci ata_piix tg3 libahci libata uhci_hcd ptp ehci_hcd pps_core usbcore scsi_mod libphy usb_common [last unloaded: l2tp_core]
[ 1937.664005] CPU: 0 PID: 10022 Comm: l2tpstress Tainted: G O 3.17.0-rc1 #1
[ 1937.664005] Hardware name: HP ProLiant DL160 G5, BIOS O12 08/22/2008
[ 1937.664005] task: ffff8800d8fda790 ti: ffff8800c43c4000 task.ti: ffff8800c43c4000
[ 1937.664005] RIP: 0010:[<ffffffffa049db88>] [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp]
[ 1937.664005] RSP: 0018:ffff8800c43c7de8 EFLAGS: 00010282
[ 1937.664005] RAX: ffff8800da8a7240 RBX: ffff8800d8c64600 RCX: 000001c325a137b5
[ 1937.664005] RDX: 8c6318c6318c6320 RSI: 000000000000010c RDI: 0000000000000000
[ 1937.664005] RBP: ffff8800c43c7ea8 R08: 0000000000000000 R09: 0000000000000000
[ 1937.664005] R10: ffffffffa048e2c0 R11: ffff8800d8c64600 R12: ffff8800ca7a5000
[ 1937.664005] R13: ffff8800c439bf40 R14: 000000000000000c R15: 0000000000000009
[ 1937.664005] FS: 00007fd7f610f700(0000) GS:ffff88011a600000(0000) knlGS:0000000000000000
[ 1937.664005] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 1937.664005] CR2: 0000000000000020 CR3: 00000000d9d75000 CR4: 00000000000027e0
[ 1937.664005] Stack:
[ 1937.664005] ffffffffa049da80 ffff8800d8fda790 000000000000005b ffff880000000009
[ 1937.664005] ffff8800daf3f200 0000000000000003 ffff8800c43c7e48 ffffffff81109b57
[ 1937.664005] ffffffff81109b0e ffffffff8114c566 0000000000000000 0000000000000000
[ 1937.664005] Call Trace:
[ 1937.664005] [<ffffffffa049da80>] ? pppol2tp_connect+0x235/0x41e [l2tp_ppp]
[ 1937.664005] [<ffffffff81109b57>] ? might_fault+0x9e/0xa5
[ 1937.664005] [<ffffffff81109b0e>] ? might_fault+0x55/0xa5
[ 1937.664005] [<ffffffff8114c566>] ? rcu_read_unlock+0x1c/0x26
[ 1937.664005] [<ffffffff81309196>] SYSC_connect+0x87/0xb1
[ 1937.664005] [<ffffffff813e56f7>] ? sysret_check+0x1b/0x56
[ 1937.664005] [<ffffffff8107590d>] ? trace_hardirqs_on_caller+0x145/0x1a1
[ 1937.664005] [<ffffffff81213dee>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[ 1937.664005] [<ffffffff8114c262>] ? spin_lock+0x9/0xb
[ 1937.664005] [<ffffffff813092b4>] SyS_connect+0x9/0xb
[ 1937.664005] [<ffffffff813e56d2>] system_call_fastpath+0x16/0x1b
[ 1937.664005] Code: 10 2a 84 81 e8 65 76 bd e0 65 ff 0c 25 10 bb 00 00 4d 85 ed 74 37 48 8b 85 60 ff ff ff 48 8b 80 88 01 00 00 48 8b b8 10 02 00 00 <48> 8b 47 20 ff 50 20 85 c0 74 0f 83 e8 28 89 83 10 01 00 00 89
[ 1937.664005] RIP [<ffffffffa049db88>] pppol2tp_connect+0x33d/0x41e [l2tp_ppp]
[ 1937.664005] RSP <ffff8800c43c7de8>
[ 1937.664005] CR2: 0000000000000020
[ 1939.559375] ---[ end trace 82d44500f28f8708 ]---
Fixes: f34c4a35d879 ("l2tp: take PMTU from tunnel UDP socket")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
net/l2tp/l2tp_ppp.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/net/l2tp/l2tp_ppp.c
+++ b/net/l2tp/l2tp_ppp.c
@@ -756,7 +756,8 @@ static int pppol2tp_connect(struct socke
/* If PMTU discovery was enabled, use the MTU that was discovered */
dst = sk_dst_get(tunnel->sock);
if (dst != NULL) {
- u32 pmtu = dst_mtu(__sk_dst_get(tunnel->sock));
+ u32 pmtu = dst_mtu(dst);
+
if (pmtu != 0)
session->mtu = session->mru = pmtu -
PPPOL2TP_HEADER_OVERHEAD;
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 07/16] tg3: Work around HW/FW limitations with vlan encapsulated frames
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (5 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 06/16] l2tp: fix race while getting PMTU on PPP pseudo-wire Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 08/16] tg3: Allow for recieve of full-size 8021AD frames Greg Kroah-Hartman
` (10 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, Prashant Sreedharan, Michael Chan,
Vladislav Yasevich, David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Vlad Yasevich <vyasevich@gmail.com>
[ Upstream commit 476c18850c6cbaa3f2bb661ae9710645081563b9 ]
TG3 appears to have an issue performing TSO and checksum offloading
correclty when the frame has been vlan encapsulated (non-accelrated).
In these cases, tcp checksum is not correctly updated.
This patch attempts to work around this issue. After the patch,
802.1ad vlans start working correctly over tg3 devices.
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/net/ethernet/broadcom/tg3.c | 20 ++++++++++++++++++--
1 file changed, 18 insertions(+), 2 deletions(-)
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -7759,8 +7759,6 @@ static netdev_tx_t tg3_start_xmit(struct
entry = tnapi->tx_prod;
base_flags = 0;
- if (skb->ip_summed == CHECKSUM_PARTIAL)
- base_flags |= TXD_FLAG_TCPUDP_CSUM;
mss = skb_shinfo(skb)->gso_size;
if (mss) {
@@ -7776,6 +7774,13 @@ static netdev_tx_t tg3_start_xmit(struct
hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb) - ETH_HLEN;
+ /* HW/FW can not correctly segment packets that have been
+ * vlan encapsulated.
+ */
+ if (skb->protocol == htons(ETH_P_8021Q) ||
+ skb->protocol == htons(ETH_P_8021AD))
+ return tg3_tso_bug(tp, skb);
+
if (!skb_is_gso_v6(skb)) {
iph->check = 0;
iph->tot_len = htons(mss + hdr_len);
@@ -7822,6 +7827,17 @@ static netdev_tx_t tg3_start_xmit(struct
base_flags |= tsflags << 12;
}
}
+ } else if (skb->ip_summed == CHECKSUM_PARTIAL) {
+ /* HW/FW can not correctly checksum packets that have been
+ * vlan encapsulated.
+ */
+ if (skb->protocol == htons(ETH_P_8021Q) ||
+ skb->protocol == htons(ETH_P_8021AD)) {
+ if (skb_checksum_help(skb))
+ goto drop;
+ } else {
+ base_flags |= TXD_FLAG_TCPUDP_CSUM;
+ }
}
if (tg3_flag(tp, USE_JUMBO_BDFLAG) &&
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 08/16] tg3: Allow for recieve of full-size 8021AD frames
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (6 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 07/16] tg3: Work around HW/FW limitations with vlan encapsulated frames Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 09/16] hyperv: Fix a bug in netvsc_start_xmit() Greg Kroah-Hartman
` (9 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, Prashant Sreedharan, Michael Chan,
Vladislav Yasevich, David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Vlad Yasevich <vyasevich@gmail.com>
[ Upstream commit 7d3083ee36b51e425b6abd76778a2046906b0fd3 ]
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/net/ethernet/broadcom/tg3.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/drivers/net/ethernet/broadcom/tg3.c
+++ b/drivers/net/ethernet/broadcom/tg3.c
@@ -6767,7 +6767,8 @@ static int tg3_rx(struct tg3_napi *tnapi
skb->protocol = eth_type_trans(skb, tp->dev);
if (len > (tp->dev->mtu + ETH_HLEN) &&
- skb->protocol != htons(ETH_P_8021Q)) {
+ skb->protocol != htons(ETH_P_8021Q) &&
+ skb->protocol != htons(ETH_P_8021AD)) {
dev_kfree_skb(skb);
goto drop_it_no_recycle;
}
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 09/16] hyperv: Fix a bug in netvsc_start_xmit()
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (7 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 08/16] tg3: Allow for recieve of full-size 8021AD frames Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 10/16] ip6_gre: fix flowi6_proto value in xmit path Greg Kroah-Hartman
` (8 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, K. Y. Srinivasan, Long Li,
Sitsofe Wheeler, David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: KY Srinivasan <kys@microsoft.com>
[ Upstream commit dedb845ded56ded1c62f5398a94ffa8615d4592d ]
After the packet is successfully sent, we should not touch the skb
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
In this version of the patch I have fixed issues pointed out by David.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Tested-by: Long Li <longli@microsoft.com>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/net/hyperv/netvsc_drv.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
--- a/drivers/net/hyperv/netvsc_drv.c
+++ b/drivers/net/hyperv/netvsc_drv.c
@@ -138,6 +138,7 @@ static int netvsc_start_xmit(struct sk_b
struct hv_netvsc_packet *packet;
int ret;
unsigned int i, num_pages, npg_data;
+ u32 skb_length = skb->len;
/* Add multipages for skb->data and additional 2 for RNDIS */
npg_data = (((unsigned long)skb->data + skb_headlen(skb) - 1)
@@ -208,7 +209,7 @@ static int netvsc_start_xmit(struct sk_b
ret = rndis_filter_send(net_device_ctx->device_ctx,
packet);
if (ret == 0) {
- net->stats.tx_bytes += skb->len;
+ net->stats.tx_bytes += skb_length;
net->stats.tx_packets++;
} else {
kfree(packet);
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 10/16] ip6_gre: fix flowi6_proto value in xmit path
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (8 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 09/16] hyperv: Fix a bug in netvsc_start_xmit() Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 11/16] sctp: handle association restarts when the socket is closed Greg Kroah-Hartman
` (7 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, Matthieu Ternisien dOuville,
Nicolas Dichtel, David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Nicolas Dichtel <nicolas.dichtel@6wind.com>
[ Upstream commit 3be07244b7337760a3269d56b2f4a63e72218648 ]
In xmit path, we build a flowi6 which will be used for the output route lookup.
We are sending a GRE packet, neither IPv4 nor IPv6 encapsulated packet, thus the
protocol should be IPPROTO_GRE.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6")
Reported-by: Matthieu Ternisien d'Ouville <matthieu.tdo@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
net/ipv6/ip6_gre.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
--- a/net/ipv6/ip6_gre.c
+++ b/net/ipv6/ip6_gre.c
@@ -787,7 +787,7 @@ static inline int ip6gre_xmit_ipv4(struc
encap_limit = t->parms.encap_limit;
memcpy(&fl6, &t->fl.u.ip6, sizeof(fl6));
- fl6.flowi6_proto = IPPROTO_IPIP;
+ fl6.flowi6_proto = IPPROTO_GRE;
dsfield = ipv4_get_dsfield(iph);
@@ -837,7 +837,7 @@ static inline int ip6gre_xmit_ipv6(struc
encap_limit = t->parms.encap_limit;
memcpy(&fl6, &t->fl.u.ip6, sizeof(fl6));
- fl6.flowi6_proto = IPPROTO_IPV6;
+ fl6.flowi6_proto = IPPROTO_GRE;
dsfield = ipv6_get_dsfield(ipv6h);
if (t->parms.flags & IP6_TNL_F_USE_ORIG_TCLASS)
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 11/16] sctp: handle association restarts when the socket is closed.
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (9 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 10/16] ip6_gre: fix flowi6_proto value in xmit path Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 12/16] tcp: fixing TLPs FIN recovery Greg Kroah-Hartman
` (6 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, David Laight, Vlad Yasevich,
David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Vlad Yasevich <vyasevich@gmail.com>
[ Upstream commit bdf6fa52f01b941d4a80372d56de465bdbbd1d23 ]
Currently association restarts do not take into consideration the
state of the socket. When a restart happens, the current assocation
simply transitions into established state. This creates a condition
where a remote system, through a the restart procedure, may create a
local association that is no way reachable by user. The conditions
to trigger this are as follows:
1) Remote does not acknoledge some data causing data to remain
outstanding.
2) Local application calls close() on the socket. Since data
is still outstanding, the association is placed in SHUTDOWN_PENDING
state. However, the socket is closed.
3) The remote tries to create a new association, triggering a restart
on the local system. The association moves from SHUTDOWN_PENDING
to ESTABLISHED. At this point, it is no longer reachable by
any socket on the local system.
This patch addresses the above situation by moving the newly ESTABLISHED
association into SHUTDOWN-SENT state and bundling a SHUTDOWN after
the COOKIE-ACK chunk. This way, the restarted associate immidiately
enters the shutdown procedure and forces the termination of the
unreachable association.
Reported-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
include/net/sctp/command.h | 2 +-
net/sctp/sm_statefuns.c | 19 ++++++++++++++++---
2 files changed, 17 insertions(+), 4 deletions(-)
--- a/include/net/sctp/command.h
+++ b/include/net/sctp/command.h
@@ -118,7 +118,7 @@ typedef enum {
* analysis of the state functions, but in reality just taken from
* thin air in the hopes othat we don't trigger a kernel panic.
*/
-#define SCTP_MAX_NUM_COMMANDS 14
+#define SCTP_MAX_NUM_COMMANDS 20
typedef union {
__s32 i32;
--- a/net/sctp/sm_statefuns.c
+++ b/net/sctp/sm_statefuns.c
@@ -1782,9 +1782,22 @@ static sctp_disposition_t sctp_sf_do_dup
/* Update the content of current association. */
sctp_add_cmd_sf(commands, SCTP_CMD_UPDATE_ASSOC, SCTP_ASOC(new_asoc));
sctp_add_cmd_sf(commands, SCTP_CMD_EVENT_ULP, SCTP_ULPEVENT(ev));
- sctp_add_cmd_sf(commands, SCTP_CMD_NEW_STATE,
- SCTP_STATE(SCTP_STATE_ESTABLISHED));
- sctp_add_cmd_sf(commands, SCTP_CMD_REPLY, SCTP_CHUNK(repl));
+ if (sctp_state(asoc, SHUTDOWN_PENDING) &&
+ (sctp_sstate(asoc->base.sk, CLOSING) ||
+ sock_flag(asoc->base.sk, SOCK_DEAD))) {
+ /* if were currently in SHUTDOWN_PENDING, but the socket
+ * has been closed by user, don't transition to ESTABLISHED.
+ * Instead trigger SHUTDOWN bundled with COOKIE_ACK.
+ */
+ sctp_add_cmd_sf(commands, SCTP_CMD_REPLY, SCTP_CHUNK(repl));
+ return sctp_sf_do_9_2_start_shutdown(net, ep, asoc,
+ SCTP_ST_CHUNK(0), NULL,
+ commands);
+ } else {
+ sctp_add_cmd_sf(commands, SCTP_CMD_NEW_STATE,
+ SCTP_STATE(SCTP_STATE_ESTABLISHED));
+ sctp_add_cmd_sf(commands, SCTP_CMD_REPLY, SCTP_CHUNK(repl));
+ }
return SCTP_DISPOSITION_CONSUME;
nomem_ev:
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 12/16] tcp: fixing TLPs FIN recovery
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (10 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 11/16] sctp: handle association restarts when the socket is closed Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 13/16] ipv6: reallocate addrconf router for ipv6 address when lo device up Greg Kroah-Hartman
` (5 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, Per Hurtig, Eric Dumazet,
Nandita Dukkipati, Neal Cardwell, David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Per Hurtig <per.hurtig@kau.se>
[ Upstream commit bef1909ee3ed1ca39231b260a8d3b4544ecd0c8f ]
Fix to a problem observed when losing a FIN segment that does not
contain data. In such situations, TLP is unable to recover from
*any* tail loss and instead adds at least PTO ms to the
retransmission process, i.e., RTO = RTO + PTO.
Signed-off-by: Per Hurtig <per.hurtig@kau.se>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
net/ipv4/tcp_output.c | 4 +---
1 file changed, 1 insertion(+), 3 deletions(-)
--- a/net/ipv4/tcp_output.c
+++ b/net/ipv4/tcp_output.c
@@ -2036,9 +2036,7 @@ void tcp_send_loss_probe(struct sock *sk
if (WARN_ON(!skb || !tcp_skb_pcount(skb)))
goto rearm_timer;
- /* Probe with zero data doesn't trigger fast recovery. */
- if (skb->len > 0)
- err = __tcp_retransmit_skb(sk, skb);
+ err = __tcp_retransmit_skb(sk, skb);
/* Record snd_nxt for loss detection. */
if (likely(!err))
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 13/16] ipv6: reallocate addrconf router for ipv6 address when lo device up
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (11 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 12/16] tcp: fixing TLPs FIN recovery Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 14/16] USB: Add device quirk for ASUS T100 Base Station keyboard Greg Kroah-Hartman
` (4 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel
Cc: Greg Kroah-Hartman, stable, Sabrina Dubroca, Hannes Frederic Sowa,
Weilong Chen, Gao feng, David S. Miller
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Gao feng <gaofeng@cn.fujitsu.com>
[ Upstream commit 33d99113b1102c2d2f8603b9ba72d89d915c13f5 ]
commit 25fb6ca4ed9cad72f14f61629b68dc03c0d9713f
"net IPv6 : Fix broken IPv6 routing table after loopback down-up"
allocates addrconf router for ipv6 address when lo device up.
but commit a881ae1f625c599b460cc8f8a7fcb1c438f699ad
"ipv6:don't call addrconf_dst_alloc again when enable lo" breaks
this behavior.
Since the addrconf router is moved to the garbage list when
lo device down, we should release this router and rellocate
a new one for ipv6 address when lo device up.
This patch solves bug 67951 on bugzilla
https://bugzilla.kernel.org/show_bug.cgi?id=67951
change from v1:
use ip6_rt_put to repleace ip6_del_rt, thanks Hannes!
change code style, suggested by Sergei.
CC: Sabrina Dubroca <sd@queasysnail.net>
CC: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reported-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
net/ipv6/addrconf.c | 14 ++++++++++++--
1 file changed, 12 insertions(+), 2 deletions(-)
--- a/net/ipv6/addrconf.c
+++ b/net/ipv6/addrconf.c
@@ -2691,8 +2691,18 @@ static void init_loopback(struct net_dev
if (sp_ifa->flags & (IFA_F_DADFAILED | IFA_F_TENTATIVE))
continue;
- if (sp_ifa->rt)
- continue;
+ if (sp_ifa->rt) {
+ /* This dst has been added to garbage list when
+ * lo device down, release this obsolete dst and
+ * reallocate a new router for ifa.
+ */
+ if (sp_ifa->rt->dst.obsolete > 0) {
+ ip6_rt_put(sp_ifa->rt);
+ sp_ifa->rt = NULL;
+ } else {
+ continue;
+ }
+ }
sp_rt = addrconf_dst_alloc(idev, &sp_ifa->addr, 0);
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 14/16] USB: Add device quirk for ASUS T100 Base Station keyboard
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (12 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 13/16] ipv6: reallocate addrconf router for ipv6 address when lo device up Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 15/16] USB: serial: cp210x: added Ketra N1 wireless interface support Greg Kroah-Hartman
` (3 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel; +Cc: Greg Kroah-Hartman, stable, Lu Baolu, Alan Stern
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Lu Baolu <baolu.lu@linux.intel.com>
commit ddbe1fca0bcb87ca8c199ea873a456ca8a948567 upstream.
This full-speed USB device generates spurious remote wakeup event
as soon as USB_DEVICE_REMOTE_WAKEUP feature is set. As the result,
Linux can't enter system suspend and S0ix power saving modes once
this keyboard is used.
This patch tries to introduce USB_QUIRK_IGNORE_REMOTE_WAKEUP quirk.
With this quirk set, wakeup capability will be ignored during
device configure.
This patch could be back-ported to kernels as old as 2.6.39.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/usb/core/hub.c | 6 ++++--
drivers/usb/core/quirks.c | 4 ++++
include/linux/usb/quirks.h | 3 +++
3 files changed, 11 insertions(+), 2 deletions(-)
--- a/drivers/usb/core/hub.c
+++ b/drivers/usb/core/hub.c
@@ -1951,8 +1951,10 @@ void usb_set_device_state(struct usb_dev
|| new_state == USB_STATE_SUSPENDED)
; /* No change to wakeup settings */
else if (new_state == USB_STATE_CONFIGURED)
- wakeup = udev->actconfig->desc.bmAttributes
- & USB_CONFIG_ATT_WAKEUP;
+ wakeup = (udev->quirks &
+ USB_QUIRK_IGNORE_REMOTE_WAKEUP) ? 0 :
+ udev->actconfig->desc.bmAttributes &
+ USB_CONFIG_ATT_WAKEUP;
else
wakeup = 0;
}
--- a/drivers/usb/core/quirks.c
+++ b/drivers/usb/core/quirks.c
@@ -162,6 +162,10 @@ static const struct usb_device_id usb_in
{ USB_VENDOR_AND_INTERFACE_INFO(0x046d, USB_CLASS_VIDEO, 1, 0),
.driver_info = USB_QUIRK_RESET_RESUME },
+ /* ASUS Base Station(T100) */
+ { USB_DEVICE(0x0b05, 0x17e0), .driver_info =
+ USB_QUIRK_IGNORE_REMOTE_WAKEUP },
+
{ } /* terminating entry must be last */
};
--- a/include/linux/usb/quirks.h
+++ b/include/linux/usb/quirks.h
@@ -30,4 +30,7 @@
descriptor */
#define USB_QUIRK_DELAY_INIT 0x00000040
+/* device generates spurious wakeup, ignore remote wakeup capability */
+#define USB_QUIRK_IGNORE_REMOTE_WAKEUP 0x00000200
+
#endif /* __LINUX_USB_QUIRKS_H */
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 15/16] USB: serial: cp210x: added Ketra N1 wireless interface support
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (13 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 14/16] USB: Add device quirk for ASUS T100 Base Station keyboard Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 2:24 ` [PATCH 3.10 16/16] USB: cp210x: add support for Seluxit USB dongle Greg Kroah-Hartman
` (2 subsequent siblings)
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel; +Cc: Greg Kroah-Hartman, stable, Joe Savage, Johan Hovold
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Joe Savage <joe.savage@goketra.com>
commit bfc2d7dfdd761ae3beccdb26abebe03cef042f46 upstream.
Added support for Ketra N1 wireless interface, which uses the
Silicon Labs' CP2104 USB to UART bridge with customized PID 8946.
Signed-off-by: Joe Savage <joe.savage@goketra.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/usb/serial/cp210x.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/usb/serial/cp210x.c
+++ b/drivers/usb/serial/cp210x.c
@@ -122,6 +122,7 @@ static const struct usb_device_id id_tab
{ USB_DEVICE(0x10C4, 0x8665) }, /* AC-Services OBD-IF */
{ USB_DEVICE(0x10C4, 0x88A4) }, /* MMB Networks ZigBee USB Device */
{ USB_DEVICE(0x10C4, 0x88A5) }, /* Planet Innovation Ingeni ZigBee USB Device */
+ { USB_DEVICE(0x10C4, 0x8946) }, /* Ketra N1 Wireless Interface */
{ USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
{ USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
{ USB_DEVICE(0x10C4, 0xEA70) }, /* Silicon Labs factory default */
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH 3.10 16/16] USB: cp210x: add support for Seluxit USB dongle
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (14 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 15/16] USB: serial: cp210x: added Ketra N1 wireless interface support Greg Kroah-Hartman
@ 2014-10-13 2:24 ` Greg Kroah-Hartman
2014-10-13 15:17 ` [PATCH 3.10 00/16] 3.10.58-stable review Guenter Roeck
2014-10-13 20:31 ` Shuah Khan
17 siblings, 0 replies; 19+ messages in thread
From: Greg Kroah-Hartman @ 2014-10-13 2:24 UTC (permalink / raw)
To: linux-kernel; +Cc: Greg Kroah-Hartman, stable, Andreas Bomholtz, Johan Hovold
3.10-stable review patch. If anyone has any objections, please let me know.
------------------
From: Andreas Bomholtz <andreas@seluxit.com>
commit dee80ad12d2b1b304286a707fde7ab05d1fc7bab upstream.
Added the Seluxit ApS USB Serial Dongle to cp210x driver.
Signed-off-by: Andreas Bomholtz <andreas@seluxit.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/usb/serial/cp210x.c | 1 +
1 file changed, 1 insertion(+)
--- a/drivers/usb/serial/cp210x.c
+++ b/drivers/usb/serial/cp210x.c
@@ -156,6 +156,7 @@ static const struct usb_device_id id_tab
{ USB_DEVICE(0x1ADB, 0x0001) }, /* Schweitzer Engineering C662 Cable */
{ USB_DEVICE(0x1B1C, 0x1C00) }, /* Corsair USB Dongle */
{ USB_DEVICE(0x1BE3, 0x07A6) }, /* WAGO 750-923 USB Service Cable */
+ { USB_DEVICE(0x1D6F, 0x0010) }, /* Seluxit ApS RF Dongle */
{ USB_DEVICE(0x1E29, 0x0102) }, /* Festo CPX-USB */
{ USB_DEVICE(0x1E29, 0x0501) }, /* Festo CMSP */
{ USB_DEVICE(0x1FB9, 0x0100) }, /* Lake Shore Model 121 Current Source */
^ permalink raw reply [flat|nested] 19+ messages in thread* Re: [PATCH 3.10 00/16] 3.10.58-stable review
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (15 preceding siblings ...)
2014-10-13 2:24 ` [PATCH 3.10 16/16] USB: cp210x: add support for Seluxit USB dongle Greg Kroah-Hartman
@ 2014-10-13 15:17 ` Guenter Roeck
2014-10-13 20:31 ` Shuah Khan
17 siblings, 0 replies; 19+ messages in thread
From: Guenter Roeck @ 2014-10-13 15:17 UTC (permalink / raw)
To: Greg Kroah-Hartman, linux-kernel
Cc: torvalds, akpm, satoru.takeuchi, shuah.kh, stable
On 10/12/2014 07:23 PM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 3.10.58 release.
> There are 16 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Wed Oct 15 02:23:28 UTC 2014.
> Anything received after that time might be too late.
>
Build results:
total: 137 pass: 137 fail: 0
Qemu test results:
total: 27 pass: 27 fail: 0
Details are available at http://server.roeck-us.net:8010/builders.
Guenter
^ permalink raw reply [flat|nested] 19+ messages in thread* Re: [PATCH 3.10 00/16] 3.10.58-stable review
2014-10-13 2:23 [PATCH 3.10 00/16] 3.10.58-stable review Greg Kroah-Hartman
` (16 preceding siblings ...)
2014-10-13 15:17 ` [PATCH 3.10 00/16] 3.10.58-stable review Guenter Roeck
@ 2014-10-13 20:31 ` Shuah Khan
17 siblings, 0 replies; 19+ messages in thread
From: Shuah Khan @ 2014-10-13 20:31 UTC (permalink / raw)
To: Greg Kroah-Hartman, linux-kernel
Cc: torvalds, akpm, linux, satoru.takeuchi, shuah.kh, stable
On 10/12/2014 08:23 PM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 3.10.58 release.
> There are 16 patches in this series, all will be posted as a response
> to this one. If anyone has any issues with these being applied, please
> let me know.
>
> Responses should be made by Wed Oct 15 02:23:28 UTC 2014.
> Anything received after that time might be too late.
>
> The whole patch series can be found in one patch at:
> kernel.org/pub/linux/kernel/v3.0/stable-review/patch-3.10.58-rc1.gz
> and the diffstat can be found below.
>
> thanks,
>
> greg k-h
>
Compiled and booted on my test system. No dmesg regressions.
-- Shuah
--
Shuah Khan
Sr. Linux Kernel Developer
Samsung Research America (Silicon Valley)
shuahkh@osg.samsung.com | (970) 217-8978
^ permalink raw reply [flat|nested] 19+ messages in thread