[PATCH V2] USB: serial: ftdi_sio: add device ID for Microsemi/Arrow SF2PLUS Dev Kit

[Marek Vasut <marex@denx.de>]

This development kit has an FT4232 on it with a custom USB VID/PID.
The FT4232 provides four UARTs, but only two are used. The UART 0
is used by the FlashPro5 programmer and UART 2 is connected to the
SmartFusion2 CortexM3 SoC UART port.

Note that the USB VID is registered to Actel according to Linux USB
VID database, but that was acquired by Microsemi.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: stable <stable@vger.kernel.org>
Cc: usb <linux-usb@vger.kernel.org>
Cc: Johan Hovold <johan@kernel.org>
---
V2: - Move the ID in ftdi_sio_ids.h to keep it sorted by VIDs
    - Use the JTAG quirk to avoid binding channel 0, this is needed by
      the Libero software, otherwise it cannot use the programmer.
---
 drivers/usb/serial/ftdi_sio.c     |  2 ++
 drivers/usb/serial/ftdi_sio_ids.h | 10 ++++++++++
 2 files changed, 12 insertions(+)

diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 80c6d3deb80d..a42e7f2af420 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -873,6 +873,8 @@ static const struct usb_device_id id_table_combined[] = {
 	{ USB_DEVICE_AND_INTERFACE_INFO(MICROCHIP_VID, MICROCHIP_USB_BOARD_PID,
 					USB_CLASS_VENDOR_SPEC,
 					USB_SUBCLASS_VENDOR_SPEC, 0x00) },
+	{ USB_DEVICE(ACTEL_VID, MICROSEMI_ARROW_SF2PLUS_BOARD_PID),
+		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
 	{ USB_DEVICE(JETI_VID, JETI_SPC1201_PID) },
 	{ USB_DEVICE(MARVELL_VID, MARVELL_SHEEVAPLUG_PID),
 		.driver_info = (kernel_ulong_t)&ftdi_jtag_quirk },
diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h
index 168ccb03ce08..7b6edb8e9ee2 100644
--- a/drivers/usb/serial/ftdi_sio_ids.h
+++ b/drivers/usb/serial/ftdi_sio_ids.h
@@ -877,6 +877,16 @@
 #define	FIC_VID			0x1457
 #define	FIC_NEO1973_DEBUG_PID	0x5118
 
+/*
+ * Microsemi/Arrow SF2PLUS Dev Kit
+ *
+ * This board has an FT4232 on it which provides four UART ports.
+ * UART 0 is used by the FlashPro5 programmer, UART 2 is connected
+ * to the UART of an CortexM3 SoC-FPGA on the board.
+ */
+#define ACTEL_VID				0x1514
+#define MICROSEMI_ARROW_SF2PLUS_BOARD_PID	0x2008
+
 /* Olimex */
 #define OLIMEX_VID			0x15BA
 #define OLIMEX_ARM_USB_OCD_PID		0x0003
-- 
2.11.0