[PATCH AUTOSEL 4.4 20/20] pinctrl: qcom: spmi-gpio: Fix pmic_gpio_config_get() to be compliant

[Sasha Levin <Alexander.Levin@microsoft.com>]

From: Douglas Anderson <dianders@chromium.org>

[ Upstream commit 1cf86bc21257a330e3af51f2a4e885f1a705f6a5 ]

If you do this on an sdm845 board:
  grep "" /sys/kernel/debug/pinctrl/*spmi:pmic*/pinconf-groups

...it looks like nonsense.  For every pin you see listed:
  input bias disabled, input bias high impedance, input bias pull down, input bias pull up, ...

That's because pmic_gpio_config_get() isn't complying with the rules
that pinconf_generic_dump_one() expects.  Specifically for boolean
parameters (anything with a "struct pin_config_item" where has_arg is
false) the function expects that the function should return its value
not through the "config" parameter but should return "0" if the value
is set and "-EINVAL" if the value isn't set.

Let's fix this.

>From a quick sample of other pinctrl drivers, it appears to be
tradition to also return 1 through the config parameter for these
boolean parameters when they exist.  I'm not one to knock tradition,
so I'll follow tradition and return 1 in these cases.  While I'm at
it, I'll also continue searching for four leaf clovers, kocking on
wood three times, and trying not to break mirrors.

NOTE: This also fixes an apparent typo for reading
PIN_CONFIG_BIAS_DISABLE where the old driver was accidentally
using "=" instead of "==" and thus was setting some internal
state when you tried to query PIN_CONFIG_BIAS_DISABLE.  Oops.

Fixes: eadff3024472 ("pinctrl: Qualcomm SPMI PMIC GPIO pin controller driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
---
 drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 32 ++++++++++++++++++------
 1 file changed, 24 insertions(+), 8 deletions(-)

diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
index 6c42ca14d2fd..4ea810cafaac 100644
--- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
@@ -291,31 +291,47 @@ static int pmic_gpio_config_get(struct pinctrl_dev *pctldev,
 
 	switch (param) {
 	case PIN_CONFIG_DRIVE_PUSH_PULL:
-		arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_CMOS;
+		if (pad->buffer_type != PMIC_GPIO_OUT_BUF_CMOS)
+			return -EINVAL;
+		arg = 1;
 		break;
 	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
-		arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS;
+		if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_NMOS)
+			return -EINVAL;
+		arg = 1;
 		break;
 	case PIN_CONFIG_DRIVE_OPEN_SOURCE:
-		arg = pad->buffer_type == PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS;
+		if (pad->buffer_type != PMIC_GPIO_OUT_BUF_OPEN_DRAIN_PMOS)
+			return -EINVAL;
+		arg = 1;
 		break;
 	case PIN_CONFIG_BIAS_PULL_DOWN:
-		arg = pad->pullup == PMIC_GPIO_PULL_DOWN;
+		if (pad->pullup != PMIC_GPIO_PULL_DOWN)
+			return -EINVAL;
+		arg = 1;
 		break;
 	case PIN_CONFIG_BIAS_DISABLE:
-		arg = pad->pullup = PMIC_GPIO_PULL_DISABLE;
+		if (pad->pullup != PMIC_GPIO_PULL_DISABLE)
+			return -EINVAL;
+		arg = 1;
 		break;
 	case PIN_CONFIG_BIAS_PULL_UP:
-		arg = pad->pullup == PMIC_GPIO_PULL_UP_30;
+		if (pad->pullup != PMIC_GPIO_PULL_UP_30)
+			return -EINVAL;
+		arg = 1;
 		break;
 	case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
-		arg = !pad->is_enabled;
+		if (pad->is_enabled)
+			return -EINVAL;
+		arg = 1;
 		break;
 	case PIN_CONFIG_POWER_SOURCE:
 		arg = pad->power_source;
 		break;
 	case PIN_CONFIG_INPUT_ENABLE:
-		arg = pad->input_enabled;
+		if (!pad->input_enabled)
+			return -EINVAL;
+		arg = 1;
 		break;
 	case PIN_CONFIG_OUTPUT:
 		arg = pad->out_value;
-- 
2.17.1