From: Sasha Levin <sashal@kernel.org>
To: stable@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: Yu Zhao <yuzhao@google.com>, Ulf Hansson <ulf.hansson@linaro.org>,
Sasha Levin <sashal@kernel.org>
Subject: [PATCH AUTOSEL 3.18 08/22] mmc: sdhci-pci-o2micro: Add quirk for O2 Micro dev 0x8620 rev 0x01
Date: Wed, 31 Oct 2018 19:11:52 -0400 [thread overview]
Message-ID: <20181031231206.29509-8-sashal@kernel.org> (raw)
In-Reply-To: <20181031231206.29509-1-sashal@kernel.org>
From: Yu Zhao <yuzhao@google.com>
[ Upstream commit 5169894982bb67486d93cc1e10151712bb86bcb6 ]
This device reports SDHCI_CLOCK_INT_STABLE even though it's not
ready to take SDHCI_CLOCK_CARD_EN. The symptom is that reading
SDHCI_CLOCK_CONTROL after enabling the clock shows absence of the
bit from the register (e.g. expecting 0x0000fa07 = 0x0000fa03 |
SDHCI_CLOCK_CARD_EN but only observed the first operand).
mmc1: Timeout waiting for hardware cmd interrupt.
mmc1: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc1: sdhci: Sys addr: 0x00000000 | Version: 0x00000603
mmc1: sdhci: Blk size: 0x00000000 | Blk cnt: 0x00000000
mmc1: sdhci: Argument: 0x00000000 | Trn mode: 0x00000000
mmc1: sdhci: Present: 0x01ff0001 | Host ctl: 0x00000001
mmc1: sdhci: Power: 0x0000000f | Blk gap: 0x00000000
mmc1: sdhci: Wake-up: 0x00000000 | Clock: 0x0000fa03
mmc1: sdhci: Timeout: 0x00000000 | Int stat: 0x00000000
mmc1: sdhci: Int enab: 0x00ff0083 | Sig enab: 0x00ff0083
mmc1: sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
mmc1: sdhci: Caps: 0x25fcc8bf | Caps_1: 0x00002077
mmc1: sdhci: Cmd: 0x00000000 | Max curr: 0x005800c8
mmc1: sdhci: Resp[0]: 0x00000000 | Resp[1]: 0x00000000
mmc1: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
mmc1: sdhci: Host ctl2: 0x00000008
mmc1: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x00000000
mmc1: sdhci: ============================================
The problem happens during wakeup from S3. Adding a delay quirk
after power up reliably fixes the problem.
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/mmc/host/sdhci-pci-o2micro.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/mmc/host/sdhci-pci-o2micro.c b/drivers/mmc/host/sdhci-pci-o2micro.c
index e2ec108dba0e..a4b614a75ac0 100644
--- a/drivers/mmc/host/sdhci-pci-o2micro.c
+++ b/drivers/mmc/host/sdhci-pci-o2micro.c
@@ -336,6 +336,9 @@ int sdhci_pci_o2_probe(struct sdhci_pci_chip *chip)
pci_write_config_byte(chip->pdev, O2_SD_LOCK_WP, scratch);
break;
case PCI_DEVICE_ID_O2_SEABIRD0:
+ if (chip->pdev->revision == 0x01)
+ chip->quirks |= SDHCI_QUIRK_DELAY_AFTER_POWER;
+ /* fall through */
case PCI_DEVICE_ID_O2_SEABIRD1:
/* UnLock WP */
ret = pci_read_config_byte(chip->pdev,
--
2.17.1
next prev parent reply other threads:[~2018-10-31 23:11 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-10-31 23:11 [PATCH AUTOSEL 3.18 01/22] locking/lockdep: Fix debug_locks off performance problem Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 02/22] ataflop: fix error handling during setup Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 03/22] swim: fix cleanup on setup error Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 04/22] tun: Consistently configure generic netdev params via rtnetlink Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 05/22] perf tools: Free temporary 'sys' string in read_event_files() Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 06/22] perf tools: Cleanup trace-event-info 'tdata' leak Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 07/22] cpupower: Fix coredump on VMWare Sasha Levin
2018-10-31 23:11 ` Sasha Levin [this message]
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 09/22] x86/olpc: Indicate that legacy PC XO-1 platform should not register RTC Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 10/22] regulator: fixed: Default enable high on DT regulators Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 11/22] x86: boot: Fix EFI stub alignment Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 12/22] kprobes: Return error if we fail to reuse kprobe instead of BUG_ON() Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 13/22] ath10k: schedule hardware restart if WMI command times out Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 14/22] scsi: esp_scsi: Track residual for PIO transfers Sasha Levin
2018-10-31 23:11 ` [PATCH AUTOSEL 3.18 15/22] Drivers: hv: kvp: Fix two "this statement may fall through" warnings Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 16/22] ext4: fix argument checking in EXT4_IOC_MOVE_EXT Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 17/22] MD: fix invalid stored role for a disk Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 18/22] usb: chipidea: Prevent unbalanced IRQ disable Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 19/22] uio: ensure class is registered before devices Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 20/22] scsi: lpfc: Correct soft lockup when running mds diagnostics Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 21/22] signal: Always deliver the kernel's SIGKILL and SIGSTOP to a pid namespace init Sasha Levin
2018-10-31 23:12 ` [PATCH AUTOSEL 3.18 22/22] mfd: menelaus: Fix possible race condition and leak Sasha Levin
2018-11-01 0:27 ` Alexandre Belloni
2018-11-01 1:29 ` Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20181031231206.29509-8-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=stable@vger.kernel.org \
--cc=ulf.hansson@linaro.org \
--cc=yuzhao@google.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox