[PATCH 5.0 00/32] 5.0.13-stable review

[PATCH 5.0 00/32] 5.0.13-stable review

[Greg Kroah-Hartman]

This is the start of the stable review cycle for the 5.0.13 release.
There are 32 patches in this series, all will be posted as a response
to this one.  If anyone has any issues with these being applied, please
let me know.

Responses should be made by Mon 06 May 2019 10:24:23 AM UTC.
Anything received after that time might be too late.

The whole patch series can be found in one patch at:
	https://www.kernel.org/pub/linux/kernel/v5.x/stable-review/patch-5.0.13-rc1.gz
or in the git tree and branch at:
	git://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git linux-5.0.y
and the diffstat can be found below.

thanks,

greg k-h

-------------
Pseudo-Shortlog of commits:

Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    Linux 5.0.13-rc1

Rafael J. Wysocki <rafael.j.wysocki@intel.com>
    ath10k: Drop WARN_ON()s that always trigger during system resume

Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    iwlwifi: mvm: properly check debugfs dentry before using it

Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    ALSA: line6: use dynamic buffers

Jim Mattson <jmattson@google.com>
    KVM: nVMX: Fix size checks in vmx_set_nested_state

Sean Christopherson <sean.j.christopherson@intel.com>
    KVM: x86: Whitelist port 0x7e for pre-incrementing %rip

Jakub Kicinski <jakub.kicinski@netronome.com>
    net/tls: fix copy to fragments in reencrypt

Jakub Kicinski <jakub.kicinski@netronome.com>
    net/tls: don't copy negative amounts of data in reencrypt

Michael Chan <michael.chan@broadcom.com>
    bnxt_en: Fix uninitialized variable usage in bnxt_rx_pkt().

Michael Chan <michael.chan@broadcom.com>
    bnxt_en: Fix statistics context reservation logic.

Michael Chan <michael.chan@broadcom.com>
    bnxt_en: Pass correct extended TX port statistics size to firmware.

Michael Chan <michael.chan@broadcom.com>
    bnxt_en: Fix possible crash in bnxt_hwrm_ring_free() under error conditions.

Vasundhara Volam <vasundhara-v.volam@broadcom.com>
    bnxt_en: Free short FW command HWRM memory in error path in bnxt_init_one()

Michael Chan <michael.chan@broadcom.com>
    bnxt_en: Improve multicast address setup logic.

Eric Dumazet <edumazet@google.com>
    udp: fix GRO packet of death

Paolo Abeni <pabeni@redhat.com>
    udp: fix GRO reception in case of length mismatch

Eric Dumazet <edumazet@google.com>
    tcp: add sanity tests in tcp_add_backlog()

David Ahern <dsahern@gmail.com>
    selftests: fib_rule_tests: Fix icmp proto with ipv6

Willem de Bruijn <willemb@google.com>
    packet: in recvmsg msg_name return at least sizeof sockaddr_ll

Willem de Bruijn <willemb@google.com>
    packet: validate msg_namelen in send directly

Hangbin Liu <liuhangbin@gmail.com>
    selftests: fib_rule_tests: print the result and return 1 if any tests failed

Xin Long <lucien.xin@gmail.com>
    sctp: avoid running the sctp state machine recursively

David Howells <dhowells@redhat.com>
    rxrpc: Fix net namespace cleanup

Jakub Kicinski <jakub.kicinski@netronome.com>
    net/tls: avoid NULL pointer deref on nskb->sk in fallback

Andrew Lunn <andrew@lunn.ch>
    net: phy: marvell: Fix buffer overrun with stats counters

Dan Carpenter <dan.carpenter@oracle.com>
    net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc

Eric Dumazet <edumazet@google.com>
    l2tp: use rcu_dereference_sk_user_data() in l2tp_udp_encap_recv()

Eric Dumazet <edumazet@google.com>
    l2ip: fix possible use-after-free

Willem de Bruijn <willemb@google.com>
    ipv6: invert flowlabel sharing check in process and user mode

Eric Dumazet <edumazet@google.com>
    ipv6/flowlabel: wait rcu grace period before put_pid()

Eric Dumazet <edumazet@google.com>
    ipv6: fix races in ip6_dst_destroy()

Martin KaFai Lau <kafai@fb.com>
    ipv6: A few fixes on dereferencing rt->from

Shmulik Ladkani <shmulik@metanetworks.com>
    ipv4: ip_do_fragment: Preserve skb_iif during fragmentation


-------------

Diffstat:

 Makefile                                           |  4 +-
 arch/x86/include/uapi/asm/kvm.h                    |  1 +
 arch/x86/kvm/vmx/nested.c                          |  4 +-
 arch/x86/kvm/x86.c                                 | 21 +++++++-
 drivers/net/dsa/bcm_sf2_cfp.c                      |  6 +++
 drivers/net/ethernet/broadcom/bnxt/bnxt.c          | 53 +++++++++++--------
 drivers/net/phy/marvell.c                          |  6 ++-
 drivers/net/wireless/ath/ath10k/mac.c              |  4 +-
 .../net/wireless/intel/iwlwifi/mvm/debugfs-vif.c   |  5 ++
 include/net/sctp/command.h                         |  1 -
 net/ipv4/ip_output.c                               |  1 +
 net/ipv4/tcp_ipv4.c                                | 13 ++++-
 net/ipv4/udp_offload.c                             | 16 ++++--
 net/ipv6/ip6_fib.c                                 |  4 +-
 net/ipv6/ip6_flowlabel.c                           | 22 +++++---
 net/ipv6/route.c                                   | 47 ++++++++---------
 net/l2tp/l2tp_core.c                               | 10 ++--
 net/packet/af_packet.c                             | 37 ++++++++-----
 net/rxrpc/call_object.c                            | 32 ++++++------
 net/sctp/sm_sideeffect.c                           | 29 -----------
 net/sctp/sm_statefuns.c                            | 35 ++++++++++---
 net/tls/tls_device.c                               | 39 ++++++++++----
 net/tls/tls_device_fallback.c                      |  3 +-
 sound/usb/line6/driver.c                           | 60 +++++++++++++---------
 sound/usb/line6/podhd.c                            | 21 ++++----
 sound/usb/line6/toneport.c                         | 24 ++++++---
 tools/testing/selftests/net/fib_rule_tests.sh      | 10 +++-
 27 files changed, 309 insertions(+), 199 deletions(-)

[PATCH 5.0 01/32] ipv4: ip_do_fragment: Preserve skb_iif during fragmentation

[Greg Kroah-Hartman]

From: Shmulik Ladkani <shmulik@metanetworks.com>

[ Upstream commit d2f0c961148f65bc73eda72b9fa3a4e80973cb49 ]

Previously, during fragmentation after forwarding, skb->skb_iif isn't
preserved, i.e. 'ip_copy_metadata' does not copy skb_iif from given
'from' skb.

As a result, ip_do_fragment's creates fragments with zero skb_iif,
leading to inconsistent behavior.

Assume for example an eBPF program attached at tc egress (post
forwarding) that examines __sk_buff->ingress_ifindex:
 - the correct iif is observed if forwarding path does not involve
   fragmentation/refragmentation
 - a bogus iif is observed if forwarding path involves
   fragmentation/refragmentatiom

Fix, by preserving skb_iif during 'ip_copy_metadata'.

Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv4/ip_output.c |    1 +
 1 file changed, 1 insertion(+)

--- a/net/ipv4/ip_output.c
+++ b/net/ipv4/ip_output.c
@@ -519,6 +519,7 @@ static void ip_copy_metadata(struct sk_b
 	to->pkt_type = from->pkt_type;
 	to->priority = from->priority;
 	to->protocol = from->protocol;
+	to->skb_iif = from->skb_iif;
 	skb_dst_drop(to);
 	skb_dst_copy(to, from);
 	to->dev = from->dev;

[PATCH 5.0 02/32] ipv6: A few fixes on dereferencing rt->from

[Greg Kroah-Hartman]

From: Martin KaFai Lau <kafai@fb.com>

[ Upstream commit 886b7a50100a50f1cbd08a6f8ec5884dfbe082dc ]

It is a followup after the fix in
commit 9c69a1320515 ("route: Avoid crash from dereferencing NULL rt->from")

rt6_do_redirect():
1. NULL checking is needed on rt->from because a parallel
   fib6_info delete could happen that sets rt->from to NULL.
   (e.g. rt6_remove_exception() and fib6_drop_pcpu_from()).

2. fib6_info_hold() is not enough.  Same reason as (1).
   Meaning, holding dst->__refcnt cannot ensure
   rt->from is not NULL or rt->from->fib6_ref is not 0.

   Instead of using fib6_info_hold_safe() which ip6_rt_cache_alloc()
   is already doing, this patch chooses to extend the rcu section
   to keep "from" dereference-able after checking for NULL.

inet6_rtm_getroute():
1. NULL checking is also needed on rt->from for a similar reason.
   Note that inet6_rtm_getroute() is using RTNL_FLAG_DOIT_UNLOCKED.

Fixes: a68886a69180 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv6/route.c |   38 ++++++++++++++++++--------------------
 1 file changed, 18 insertions(+), 20 deletions(-)

--- a/net/ipv6/route.c
+++ b/net/ipv6/route.c
@@ -3403,11 +3403,8 @@ static void rt6_do_redirect(struct dst_e
 
 	rcu_read_lock();
 	from = rcu_dereference(rt->from);
-	/* This fib6_info_hold() is safe here because we hold reference to rt
-	 * and rt already holds reference to fib6_info.
-	 */
-	fib6_info_hold(from);
-	rcu_read_unlock();
+	if (!from)
+		goto out;
 
 	nrt = ip6_rt_cache_alloc(from, &msg->dest, NULL);
 	if (!nrt)
@@ -3419,10 +3416,7 @@ static void rt6_do_redirect(struct dst_e
 
 	nrt->rt6i_gateway = *(struct in6_addr *)neigh->primary_key;
 
-	/* No need to remove rt from the exception table if rt is
-	 * a cached route because rt6_insert_exception() will
-	 * takes care of it
-	 */
+	/* rt6_insert_exception() will take care of duplicated exceptions */
 	if (rt6_insert_exception(nrt, from)) {
 		dst_release_immediate(&nrt->dst);
 		goto out;
@@ -3435,7 +3429,7 @@ static void rt6_do_redirect(struct dst_e
 	call_netevent_notifiers(NETEVENT_REDIRECT, &netevent);
 
 out:
-	fib6_info_release(from);
+	rcu_read_unlock();
 	neigh_release(neigh);
 }
 
@@ -4957,16 +4951,20 @@ static int inet6_rtm_getroute(struct sk_
 
 	rcu_read_lock();
 	from = rcu_dereference(rt->from);
-
-	if (fibmatch)
-		err = rt6_fill_node(net, skb, from, NULL, NULL, NULL, iif,
-				    RTM_NEWROUTE, NETLINK_CB(in_skb).portid,
-				    nlh->nlmsg_seq, 0);
-	else
-		err = rt6_fill_node(net, skb, from, dst, &fl6.daddr,
-				    &fl6.saddr, iif, RTM_NEWROUTE,
-				    NETLINK_CB(in_skb).portid, nlh->nlmsg_seq,
-				    0);
+	if (from) {
+		if (fibmatch)
+			err = rt6_fill_node(net, skb, from, NULL, NULL, NULL,
+					    iif, RTM_NEWROUTE,
+					    NETLINK_CB(in_skb).portid,
+					    nlh->nlmsg_seq, 0);
+		else
+			err = rt6_fill_node(net, skb, from, dst, &fl6.daddr,
+					    &fl6.saddr, iif, RTM_NEWROUTE,
+					    NETLINK_CB(in_skb).portid,
+					    nlh->nlmsg_seq, 0);
+	} else {
+		err = -ENETUNREACH;
+	}
 	rcu_read_unlock();
 
 	if (err < 0) {

[PATCH 5.0 03/32] ipv6: fix races in ip6_dst_destroy()

[Greg Kroah-Hartman]

From: Eric Dumazet <edumazet@google.com>

[ Upstream commit 0e2338749192ce0e52e7174c5352f627632f478a ]

We had many syzbot reports that seem to be caused by use-after-free
of struct fib6_info.

ip6_dst_destroy(), fib6_drop_pcpu_from() and rt6_remove_exception()
are writers vs rt->from, and use non consistent synchronization among
themselves.

Switching to xchg() will solve the issues with no possible
lockdep issues.

BUG: KASAN: user-memory-access in atomic_dec_and_test include/asm-generic/atomic-instrumented.h:747 [inline]
BUG: KASAN: user-memory-access in fib6_info_release include/net/ip6_fib.h:294 [inline]
BUG: KASAN: user-memory-access in fib6_info_release include/net/ip6_fib.h:292 [inline]
BUG: KASAN: user-memory-access in fib6_drop_pcpu_from net/ipv6/ip6_fib.c:927 [inline]
BUG: KASAN: user-memory-access in fib6_purge_rt+0x4f6/0x670 net/ipv6/ip6_fib.c:960
Write of size 4 at addr 0000000000ffffb4 by task syz-executor.1/7649

CPU: 0 PID: 7649 Comm: syz-executor.1 Not tainted 5.1.0-rc6+ #183
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x172/0x1f0 lib/dump_stack.c:113
 kasan_report.cold+0x5/0x40 mm/kasan/report.c:321
 check_memory_region_inline mm/kasan/generic.c:185 [inline]
 check_memory_region+0x123/0x190 mm/kasan/generic.c:191
 kasan_check_write+0x14/0x20 mm/kasan/common.c:108
 atomic_dec_and_test include/asm-generic/atomic-instrumented.h:747 [inline]
 fib6_info_release include/net/ip6_fib.h:294 [inline]
 fib6_info_release include/net/ip6_fib.h:292 [inline]
 fib6_drop_pcpu_from net/ipv6/ip6_fib.c:927 [inline]
 fib6_purge_rt+0x4f6/0x670 net/ipv6/ip6_fib.c:960
 fib6_del_route net/ipv6/ip6_fib.c:1813 [inline]
 fib6_del+0xac2/0x10a0 net/ipv6/ip6_fib.c:1844
 fib6_clean_node+0x3a8/0x590 net/ipv6/ip6_fib.c:2006
 fib6_walk_continue+0x495/0x900 net/ipv6/ip6_fib.c:1928
 fib6_walk+0x9d/0x100 net/ipv6/ip6_fib.c:1976
 fib6_clean_tree+0xe0/0x120 net/ipv6/ip6_fib.c:2055
 __fib6_clean_all+0x118/0x2a0 net/ipv6/ip6_fib.c:2071
 fib6_clean_all+0x2b/0x40 net/ipv6/ip6_fib.c:2082
 rt6_sync_down_dev+0x134/0x150 net/ipv6/route.c:4057
 rt6_disable_ip+0x27/0x5f0 net/ipv6/route.c:4062
 addrconf_ifdown+0xa2/0x1220 net/ipv6/addrconf.c:3705
 addrconf_notify+0x19a/0x2260 net/ipv6/addrconf.c:3630
 notifier_call_chain+0xc7/0x240 kernel/notifier.c:93
 __raw_notifier_call_chain kernel/notifier.c:394 [inline]
 raw_notifier_call_chain+0x2e/0x40 kernel/notifier.c:401
 call_netdevice_notifiers_info+0x3f/0x90 net/core/dev.c:1753
 call_netdevice_notifiers_extack net/core/dev.c:1765 [inline]
 call_netdevice_notifiers net/core/dev.c:1779 [inline]
 dev_close_many+0x33f/0x6f0 net/core/dev.c:1522
 rollback_registered_many+0x43b/0xfd0 net/core/dev.c:8177
 rollback_registered+0x109/0x1d0 net/core/dev.c:8242
 unregister_netdevice_queue net/core/dev.c:9289 [inline]
 unregister_netdevice_queue+0x1ee/0x2c0 net/core/dev.c:9282
 unregister_netdevice include/linux/netdevice.h:2658 [inline]
 __tun_detach+0xd5b/0x1000 drivers/net/tun.c:727
 tun_detach drivers/net/tun.c:744 [inline]
 tun_chr_close+0xe0/0x180 drivers/net/tun.c:3443
 __fput+0x2e5/0x8d0 fs/file_table.c:278
 ____fput+0x16/0x20 fs/file_table.c:309
 task_work_run+0x14a/0x1c0 kernel/task_work.c:113
 exit_task_work include/linux/task_work.h:22 [inline]
 do_exit+0x90a/0x2fa0 kernel/exit.c:876
 do_group_exit+0x135/0x370 kernel/exit.c:980
 __do_sys_exit_group kernel/exit.c:991 [inline]
 __se_sys_exit_group kernel/exit.c:989 [inline]
 __x64_sys_exit_group+0x44/0x50 kernel/exit.c:989
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458da9
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007ffeafc2a6a8 EFLAGS: 00000246 ORIG_RAX: 00000000000000e7
RAX: ffffffffffffffda RBX: 000000000000001c RCX: 0000000000458da9
RDX: 0000000000412a80 RSI: 0000000000a54ef0 RDI: 0000000000000043
RBP: 00000000004be552 R08: 000000000000000c R09: 000000000004c0d1
R10: 0000000002341940 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00007ffeafc2a7f0 R14: 000000000004c065 R15: 00007ffeafc2a800

Fixes: a68886a69180 ("net/ipv6: Make from in rt6_info rcu protected")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: David Ahern <dsahern@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv6/ip6_fib.c |    4 +---
 net/ipv6/route.c   |    9 ++-------
 2 files changed, 3 insertions(+), 10 deletions(-)

--- a/net/ipv6/ip6_fib.c
+++ b/net/ipv6/ip6_fib.c
@@ -921,9 +921,7 @@ static void fib6_drop_pcpu_from(struct f
 		if (pcpu_rt) {
 			struct fib6_info *from;
 
-			from = rcu_dereference_protected(pcpu_rt->from,
-					     lockdep_is_held(&table->tb6_lock));
-			rcu_assign_pointer(pcpu_rt->from, NULL);
+			from = xchg((__force struct fib6_info **)&pcpu_rt->from, NULL);
 			fib6_info_release(from);
 		}
 	}
--- a/net/ipv6/route.c
+++ b/net/ipv6/route.c
@@ -379,11 +379,8 @@ static void ip6_dst_destroy(struct dst_e
 		in6_dev_put(idev);
 	}
 
-	rcu_read_lock();
-	from = rcu_dereference(rt->from);
-	rcu_assign_pointer(rt->from, NULL);
+	from = xchg((__force struct fib6_info **)&rt->from, NULL);
 	fib6_info_release(from);
-	rcu_read_unlock();
 }
 
 static void ip6_dst_ifdown(struct dst_entry *dst, struct net_device *dev,
@@ -1288,9 +1285,7 @@ static void rt6_remove_exception(struct
 	/* purge completely the exception to allow releasing the held resources:
 	 * some [sk] cache may keep the dst around for unlimited time
 	 */
-	from = rcu_dereference_protected(rt6_ex->rt6i->from,
-					 lockdep_is_held(&rt6_exception_lock));
-	rcu_assign_pointer(rt6_ex->rt6i->from, NULL);
+	from = xchg((__force struct fib6_info **)&rt6_ex->rt6i->from, NULL);
 	fib6_info_release(from);
 	dst_dev_put(&rt6_ex->rt6i->dst);
 

[PATCH 5.0 04/32] ipv6/flowlabel: wait rcu grace period before put_pid()

[Greg Kroah-Hartman]

From: Eric Dumazet <edumazet@google.com>

[ Upstream commit 6c0afef5fb0c27758f4d52b2210c61b6bd8b4470 ]

syzbot was able to catch a use-after-free read in pid_nr_ns() [1]

ip6fl_seq_show() seems to use RCU protection, dereferencing fl->owner.pid
but fl_free() releases fl->owner.pid before rcu grace period is started.

[1]

BUG: KASAN: use-after-free in pid_nr_ns+0x128/0x140 kernel/pid.c:407
Read of size 4 at addr ffff888094012a04 by task syz-executor.0/18087

CPU: 0 PID: 18087 Comm: syz-executor.0 Not tainted 5.1.0-rc6+ #89
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x172/0x1f0 lib/dump_stack.c:113
 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
 kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
 __asan_report_load4_noabort+0x14/0x20 mm/kasan/generic_report.c:131
 pid_nr_ns+0x128/0x140 kernel/pid.c:407
 ip6fl_seq_show+0x2f8/0x4f0 net/ipv6/ip6_flowlabel.c:794
 seq_read+0xad3/0x1130 fs/seq_file.c:268
 proc_reg_read+0x1fe/0x2c0 fs/proc/inode.c:227
 do_loop_readv_writev fs/read_write.c:701 [inline]
 do_loop_readv_writev fs/read_write.c:688 [inline]
 do_iter_read+0x4a9/0x660 fs/read_write.c:922
 vfs_readv+0xf0/0x160 fs/read_write.c:984
 kernel_readv fs/splice.c:358 [inline]
 default_file_splice_read+0x475/0x890 fs/splice.c:413
 do_splice_to+0x12a/0x190 fs/splice.c:876
 splice_direct_to_actor+0x2d2/0x970 fs/splice.c:953
 do_splice_direct+0x1da/0x2a0 fs/splice.c:1062
 do_sendfile+0x597/0xd00 fs/read_write.c:1443
 __do_sys_sendfile64 fs/read_write.c:1498 [inline]
 __se_sys_sendfile64 fs/read_write.c:1490 [inline]
 __x64_sys_sendfile64+0x15a/0x220 fs/read_write.c:1490
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x458da9
Code: ad b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 7b b8 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f300d24bc78 EFLAGS: 00000246 ORIG_RAX: 0000000000000028
RAX: ffffffffffffffda RBX: 0000000000000004 RCX: 0000000000458da9
RDX: 00000000200000c0 RSI: 0000000000000008 RDI: 0000000000000007
RBP: 000000000073bf00 R08: 0000000000000000 R09: 0000000000000000
R10: 000000000000005a R11: 0000000000000246 R12: 00007f300d24c6d4
R13: 00000000004c5fa3 R14: 00000000004da748 R15: 00000000ffffffff

Allocated by task 17543:
 save_stack+0x45/0xd0 mm/kasan/common.c:75
 set_track mm/kasan/common.c:87 [inline]
 __kasan_kmalloc mm/kasan/common.c:497 [inline]
 __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:470
 kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:505
 slab_post_alloc_hook mm/slab.h:437 [inline]
 slab_alloc mm/slab.c:3393 [inline]
 kmem_cache_alloc+0x11a/0x6f0 mm/slab.c:3555
 alloc_pid+0x55/0x8f0 kernel/pid.c:168
 copy_process.part.0+0x3b08/0x7980 kernel/fork.c:1932
 copy_process kernel/fork.c:1709 [inline]
 _do_fork+0x257/0xfd0 kernel/fork.c:2226
 __do_sys_clone kernel/fork.c:2333 [inline]
 __se_sys_clone kernel/fork.c:2327 [inline]
 __x64_sys_clone+0xbf/0x150 kernel/fork.c:2327
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 7789:
 save_stack+0x45/0xd0 mm/kasan/common.c:75
 set_track mm/kasan/common.c:87 [inline]
 __kasan_slab_free+0x102/0x150 mm/kasan/common.c:459
 kasan_slab_free+0xe/0x10 mm/kasan/common.c:467
 __cache_free mm/slab.c:3499 [inline]
 kmem_cache_free+0x86/0x260 mm/slab.c:3765
 put_pid.part.0+0x111/0x150 kernel/pid.c:111
 put_pid+0x20/0x30 kernel/pid.c:105
 fl_free+0xbe/0xe0 net/ipv6/ip6_flowlabel.c:102
 ip6_fl_gc+0x295/0x3e0 net/ipv6/ip6_flowlabel.c:152
 call_timer_fn+0x190/0x720 kernel/time/timer.c:1325
 expire_timers kernel/time/timer.c:1362 [inline]
 __run_timers kernel/time/timer.c:1681 [inline]
 __run_timers kernel/time/timer.c:1649 [inline]
 run_timer_softirq+0x652/0x1700 kernel/time/timer.c:1694
 __do_softirq+0x266/0x95a kernel/softirq.c:293

The buggy address belongs to the object at ffff888094012a00
 which belongs to the cache pid_2 of size 88
The buggy address is located 4 bytes inside of
 88-byte region [ffff888094012a00, ffff888094012a58)
The buggy address belongs to the page:
page:ffffea0002500480 count:1 mapcount:0 mapping:ffff88809a483080 index:0xffff888094012980
flags: 0x1fffc0000000200(slab)
raw: 01fffc0000000200 ffffea00018a3508 ffffea0002524a88 ffff88809a483080
raw: ffff888094012980 ffff888094012000 000000010000001b 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff888094012900: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc
 ffff888094012980: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc
>ffff888094012a00: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc
                   ^
 ffff888094012a80: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc
 ffff888094012b00: fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc fc

Fixes: 4f82f45730c6 ("net ip6 flowlabel: Make owner a union of struct pid * and kuid_t")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv6/ip6_flowlabel.c |   18 ++++++++++++------
 1 file changed, 12 insertions(+), 6 deletions(-)

--- a/net/ipv6/ip6_flowlabel.c
+++ b/net/ipv6/ip6_flowlabel.c
@@ -94,15 +94,21 @@ static struct ip6_flowlabel *fl_lookup(s
 	return fl;
 }
 
+static void fl_free_rcu(struct rcu_head *head)
+{
+	struct ip6_flowlabel *fl = container_of(head, struct ip6_flowlabel, rcu);
+
+	if (fl->share == IPV6_FL_S_PROCESS)
+		put_pid(fl->owner.pid);
+	kfree(fl->opt);
+	kfree(fl);
+}
+
 
 static void fl_free(struct ip6_flowlabel *fl)
 {
-	if (fl) {
-		if (fl->share == IPV6_FL_S_PROCESS)
-			put_pid(fl->owner.pid);
-		kfree(fl->opt);
-		kfree_rcu(fl, rcu);
-	}
+	if (fl)
+		call_rcu(&fl->rcu, fl_free_rcu);
 }
 
 static void fl_release(struct ip6_flowlabel *fl)

[PATCH 5.0 05/32] ipv6: invert flowlabel sharing check in process and user mode

[Greg Kroah-Hartman]

From: Willem de Bruijn <willemb@google.com>

[ Upstream commit 95c169251bf734aa555a1e8043e4d88ec97a04ec ]

A request for a flowlabel fails in process or user exclusive mode must
fail if the caller pid or uid does not match. Invert the test.

Previously, the test was unsafe wrt PID recycling, but indeed tested
for inequality: fl1->owner != fl->owner

Fixes: 4f82f45730c68 ("net ip6 flowlabel: Make owner a union of struct pid* and kuid_t")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv6/ip6_flowlabel.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/net/ipv6/ip6_flowlabel.c
+++ b/net/ipv6/ip6_flowlabel.c
@@ -639,9 +639,9 @@ recheck:
 				if (fl1->share == IPV6_FL_S_EXCL ||
 				    fl1->share != fl->share ||
 				    ((fl1->share == IPV6_FL_S_PROCESS) &&
-				     (fl1->owner.pid == fl->owner.pid)) ||
+				     (fl1->owner.pid != fl->owner.pid)) ||
 				    ((fl1->share == IPV6_FL_S_USER) &&
-				     uid_eq(fl1->owner.uid, fl->owner.uid)))
+				     !uid_eq(fl1->owner.uid, fl->owner.uid)))
 					goto release;
 
 				err = -ENOMEM;

[PATCH 5.0 06/32] l2ip: fix possible use-after-free

[Greg Kroah-Hartman]

From: Eric Dumazet <edumazet@google.com>

[ Upstream commit a622b40035d16196bf19b2b33b854862595245fc ]

Before taking a refcount on a rcu protected structure,
we need to make sure the refcount is not zero.

syzbot reported :

refcount_t: increment on 0; use-after-free.
WARNING: CPU: 1 PID: 23533 at lib/refcount.c:156 refcount_inc_checked lib/refcount.c:156 [inline]
WARNING: CPU: 1 PID: 23533 at lib/refcount.c:156 refcount_inc_checked+0x61/0x70 lib/refcount.c:154
Kernel panic - not syncing: panic_on_warn set ...
CPU: 1 PID: 23533 Comm: syz-executor.2 Not tainted 5.1.0-rc7+ #93
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x172/0x1f0 lib/dump_stack.c:113
 panic+0x2cb/0x65c kernel/panic.c:214
 __warn.cold+0x20/0x45 kernel/panic.c:571
 report_bug+0x263/0x2b0 lib/bug.c:186
 fixup_bug arch/x86/kernel/traps.c:179 [inline]
 fixup_bug arch/x86/kernel/traps.c:174 [inline]
 do_error_trap+0x11b/0x200 arch/x86/kernel/traps.c:272
 do_invalid_op+0x37/0x50 arch/x86/kernel/traps.c:291
 invalid_op+0x14/0x20 arch/x86/entry/entry_64.S:973
RIP: 0010:refcount_inc_checked lib/refcount.c:156 [inline]
RIP: 0010:refcount_inc_checked+0x61/0x70 lib/refcount.c:154
Code: 1d 98 2b 2a 06 31 ff 89 de e8 db 2c 40 fe 84 db 75 dd e8 92 2b 40 fe 48 c7 c7 20 7a a1 87 c6 05 78 2b 2a 06 01 e8 7d d9 12 fe <0f> 0b eb c1 90 90 90 90 90 90 90 90 90 90 90 55 48 89 e5 41 57 41
RSP: 0018:ffff888069f0fba8 EFLAGS: 00010286
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 000000000000f353 RSI: ffffffff815afcb6 RDI: ffffed100d3e1f67
RBP: ffff888069f0fbb8 R08: ffff88809b1845c0 R09: ffffed1015d23ef1
R10: ffffed1015d23ef0 R11: ffff8880ae91f787 R12: ffff8880a8f26968
R13: 0000000000000004 R14: dffffc0000000000 R15: ffff8880a49a6440
 l2tp_tunnel_inc_refcount net/l2tp/l2tp_core.h:240 [inline]
 l2tp_tunnel_get+0x250/0x580 net/l2tp/l2tp_core.c:173
 pppol2tp_connect+0xc00/0x1c70 net/l2tp/l2tp_ppp.c:702
 __sys_connect+0x266/0x330 net/socket.c:1808
 __do_sys_connect net/socket.c:1819 [inline]
 __se_sys_connect net/socket.c:1816 [inline]
 __x64_sys_connect+0x73/0xb0 net/socket.c:1816

Fixes: 54652eb12c1b ("l2tp: hold tunnel while looking up sessions in l2tp_netlink")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/l2tp/l2tp_core.c |    8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

--- a/net/l2tp/l2tp_core.c
+++ b/net/l2tp/l2tp_core.c
@@ -169,8 +169,8 @@ struct l2tp_tunnel *l2tp_tunnel_get(cons
 
 	rcu_read_lock_bh();
 	list_for_each_entry_rcu(tunnel, &pn->l2tp_tunnel_list, list) {
-		if (tunnel->tunnel_id == tunnel_id) {
-			l2tp_tunnel_inc_refcount(tunnel);
+		if (tunnel->tunnel_id == tunnel_id &&
+		    refcount_inc_not_zero(&tunnel->ref_count)) {
 			rcu_read_unlock_bh();
 
 			return tunnel;
@@ -190,8 +190,8 @@ struct l2tp_tunnel *l2tp_tunnel_get_nth(
 
 	rcu_read_lock_bh();
 	list_for_each_entry_rcu(tunnel, &pn->l2tp_tunnel_list, list) {
-		if (++count > nth) {
-			l2tp_tunnel_inc_refcount(tunnel);
+		if (++count > nth &&
+		    refcount_inc_not_zero(&tunnel->ref_count)) {
 			rcu_read_unlock_bh();
 			return tunnel;
 		}

[PATCH 5.0 07/32] l2tp: use rcu_dereference_sk_user_data() in l2tp_udp_encap_recv()

[Greg Kroah-Hartman]

From: Eric Dumazet <edumazet@google.com>

[ Upstream commit c1c477217882c610a2ba0268f5faf36c9c092528 ]

Canonical way to fetch sk_user_data from an encap_rcv() handler called
from UDP stack in rcu protected section is to use rcu_dereference_sk_user_data(),
otherwise compiler might read it multiple times.

Fixes: d00fa9adc528 ("il2tp: fix races with tunnel socket close")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/l2tp/l2tp_core.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

--- a/net/l2tp/l2tp_core.c
+++ b/net/l2tp/l2tp_core.c
@@ -909,7 +909,7 @@ int l2tp_udp_encap_recv(struct sock *sk,
 {
 	struct l2tp_tunnel *tunnel;
 
-	tunnel = l2tp_tunnel(sk);
+	tunnel = rcu_dereference_sk_user_data(sk);
 	if (tunnel == NULL)
 		goto pass_up;
 

[PATCH 5.0 08/32] net: dsa: bcm_sf2: fix buffer overflow doing set_rxnfc

[Greg Kroah-Hartman]

From: Dan Carpenter <dan.carpenter@oracle.com>

[ Upstream commit f949a12fd697479f68d99dc65e9bbab68ee49043 ]

The "fs->location" is a u32 that comes from the user in ethtool_set_rxnfc().
We can't pass unclamped values to test_bit() or it results in an out of
bounds access beyond the end of the bitmap.

Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/dsa/bcm_sf2_cfp.c |    6 ++++++
 1 file changed, 6 insertions(+)

--- a/drivers/net/dsa/bcm_sf2_cfp.c
+++ b/drivers/net/dsa/bcm_sf2_cfp.c
@@ -854,6 +854,9 @@ static int bcm_sf2_cfp_rule_set(struct d
 	     fs->m_ext.data[1]))
 		return -EINVAL;
 
+	if (fs->location != RX_CLS_LOC_ANY && fs->location >= CFP_NUM_RULES)
+		return -EINVAL;
+
 	if (fs->location != RX_CLS_LOC_ANY &&
 	    test_bit(fs->location, priv->cfp.used))
 		return -EBUSY;
@@ -942,6 +945,9 @@ static int bcm_sf2_cfp_rule_del(struct b
 	struct cfp_rule *rule;
 	int ret;
 
+	if (loc >= CFP_NUM_RULES)
+		return -EINVAL;
+
 	/* Refuse deleting unused rules, and those that are not unique since
 	 * that could leave IPv6 rules with one of the chained rule in the
 	 * table.

[PATCH 5.0 09/32] net: phy: marvell: Fix buffer overrun with stats counters

[Greg Kroah-Hartman]

From: Andrew Lunn <andrew@lunn.ch>

[ Upstream commit fdfdf86720a34527f777cbe0d8599bf0528fa146 ]

marvell_get_sset_count() returns how many statistics counters there
are. If the PHY supports fibre, there are 3, otherwise two.

marvell_get_strings() does not make this distinction, and always
returns 3 strings. This then often results in writing past the end
of the buffer for the strings.

Fixes: 2170fef78a40 ("Marvell phy: add field to get errors from fiber link.")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/phy/marvell.c |    6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

--- a/drivers/net/phy/marvell.c
+++ b/drivers/net/phy/marvell.c
@@ -1494,9 +1494,10 @@ static int marvell_get_sset_count(struct
 
 static void marvell_get_strings(struct phy_device *phydev, u8 *data)
 {
+	int count = marvell_get_sset_count(phydev);
 	int i;
 
-	for (i = 0; i < ARRAY_SIZE(marvell_hw_stats); i++) {
+	for (i = 0; i < count; i++) {
 		strlcpy(data + i * ETH_GSTRING_LEN,
 			marvell_hw_stats[i].string, ETH_GSTRING_LEN);
 	}
@@ -1524,9 +1525,10 @@ static u64 marvell_get_stat(struct phy_d
 static void marvell_get_stats(struct phy_device *phydev,
 			      struct ethtool_stats *stats, u64 *data)
 {
+	int count = marvell_get_sset_count(phydev);
 	int i;
 
-	for (i = 0; i < ARRAY_SIZE(marvell_hw_stats); i++)
+	for (i = 0; i < count; i++)
 		data[i] = marvell_get_stat(phydev, i);
 }
 

[PATCH 5.0 10/32] net/tls: avoid NULL pointer deref on nskb->sk in fallback

[Greg Kroah-Hartman]

From: Jakub Kicinski <jakub.kicinski@netronome.com>

[ Upstream commit 2dcb003314032c6efb13a065ffae60d164b2dd35 ]

update_chksum() accesses nskb->sk before it has been set
by complete_skb(), move the init up.

Fixes: e8f69799810c ("net/tls: Add generic NIC offload infrastructure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/tls/tls_device_fallback.c |    3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

--- a/net/tls/tls_device_fallback.c
+++ b/net/tls/tls_device_fallback.c
@@ -200,13 +200,14 @@ static void complete_skb(struct sk_buff
 
 	skb_put(nskb, skb->len);
 	memcpy(nskb->data, skb->data, headln);
-	update_chksum(nskb, headln);
 
 	nskb->destructor = skb->destructor;
 	nskb->sk = sk;
 	skb->destructor = NULL;
 	skb->sk = NULL;
 
+	update_chksum(nskb, headln);
+
 	delta = nskb->truesize - skb->truesize;
 	if (likely(delta < 0))
 		WARN_ON_ONCE(refcount_sub_and_test(-delta, &sk->sk_wmem_alloc));

[PATCH 5.0 11/32] rxrpc: Fix net namespace cleanup

[Greg Kroah-Hartman]

From: David Howells <dhowells@redhat.com>

[ Upstream commit b13023421b5179413421333f602850914f6a7ad8 ]

In rxrpc_destroy_all_calls(), there are two phases: (1) make sure the
->calls list is empty, emitting error messages if not, and (2) wait for the
RCU cleanup to happen on outstanding calls (ie. ->nr_calls becomes 0).

To avoid taking the call_lock, the function prechecks ->calls and if empty,
it returns to avoid taking the lock - this is wrong, however: it still
needs to go and do the second phase and wait for ->nr_calls to become 0.

Without this, the rxrpc_net struct may get deallocated before we get to the
RCU cleanup for the last calls.  This can lead to:

  Slab corruption (Not tainted): kmalloc-16k start=ffff88802b178000, len=16384
  050: 6b 6b 6b 6b 6b 6b 6b 6b 61 6b 6b 6b 6b 6b 6b 6b  kkkkkkkkakkkkkkk

Note the "61" at offset 0x58.  This corresponds to the ->nr_calls member of
struct rxrpc_net (which is >9k in size, and thus allocated out of the 16k
slab).

Fix this by flipping the condition on the if-statement, putting the locked
section inside the if-body and dropping the return from there.  The
function will then always go on to wait for the RCU cleanup on outstanding
calls.

Fixes: 2baec2c3f854 ("rxrpc: Support network namespacing")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/rxrpc/call_object.c |   38 +++++++++++++++++++-------------------
 1 file changed, 19 insertions(+), 19 deletions(-)

--- a/net/rxrpc/call_object.c
+++ b/net/rxrpc/call_object.c
@@ -604,30 +604,30 @@ void rxrpc_destroy_all_calls(struct rxrp
 
 	_enter("");
 
-	if (list_empty(&rxnet->calls))
-		return;
-
-	write_lock(&rxnet->call_lock);
+	if (!list_empty(&rxnet->calls)) {
+		write_lock(&rxnet->call_lock);
 
-	while (!list_empty(&rxnet->calls)) {
-		call = list_entry(rxnet->calls.next, struct rxrpc_call, link);
-		_debug("Zapping call %p", call);
-
-		rxrpc_see_call(call);
-		list_del_init(&call->link);
-
-		pr_err("Call %p still in use (%d,%s,%lx,%lx)!\n",
-		       call, atomic_read(&call->usage),
-		       rxrpc_call_states[call->state],
-		       call->flags, call->events);
+		while (!list_empty(&rxnet->calls)) {
+			call = list_entry(rxnet->calls.next,
+					  struct rxrpc_call, link);
+			_debug("Zapping call %p", call);
+
+			rxrpc_see_call(call);
+			list_del_init(&call->link);
+
+			pr_err("Call %p still in use (%d,%s,%lx,%lx)!\n",
+			       call, atomic_read(&call->usage),
+			       rxrpc_call_states[call->state],
+			       call->flags, call->events);
+
+			write_unlock(&rxnet->call_lock);
+			cond_resched();
+			write_lock(&rxnet->call_lock);
+		}
 
 		write_unlock(&rxnet->call_lock);
-		cond_resched();
-		write_lock(&rxnet->call_lock);
 	}
 
-	write_unlock(&rxnet->call_lock);
-
 	atomic_dec(&rxnet->nr_calls);
 	wait_var_event(&rxnet->nr_calls, !atomic_read(&rxnet->nr_calls));
 }

[PATCH 5.0 12/32] sctp: avoid running the sctp state machine recursively

[Greg Kroah-Hartman]

From: Xin Long <lucien.xin@gmail.com>

[ Upstream commit fbd019737d71e405f86549fd738f81e2ff3dd073 ]

Ying triggered a call trace when doing an asconf testing:

  BUG: scheduling while atomic: swapper/12/0/0x10000100
  Call Trace:
   <IRQ>  [<ffffffffa4375904>] dump_stack+0x19/0x1b
   [<ffffffffa436fcaf>] __schedule_bug+0x64/0x72
   [<ffffffffa437b93a>] __schedule+0x9ba/0xa00
   [<ffffffffa3cd5326>] __cond_resched+0x26/0x30
   [<ffffffffa437bc4a>] _cond_resched+0x3a/0x50
   [<ffffffffa3e22be8>] kmem_cache_alloc_node+0x38/0x200
   [<ffffffffa423512d>] __alloc_skb+0x5d/0x2d0
   [<ffffffffc0995320>] sctp_packet_transmit+0x610/0xa20 [sctp]
   [<ffffffffc098510e>] sctp_outq_flush+0x2ce/0xc00 [sctp]
   [<ffffffffc098646c>] sctp_outq_uncork+0x1c/0x20 [sctp]
   [<ffffffffc0977338>] sctp_cmd_interpreter.isra.22+0xc8/0x1460 [sctp]
   [<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
   [<ffffffffc099443d>] sctp_primitive_ASCONF+0x3d/0x50 [sctp]
   [<ffffffffc0977384>] sctp_cmd_interpreter.isra.22+0x114/0x1460 [sctp]
   [<ffffffffc0976ad1>] sctp_do_sm+0xe1/0x350 [sctp]
   [<ffffffffc097b3a4>] sctp_assoc_bh_rcv+0xf4/0x1b0 [sctp]
   [<ffffffffc09840f1>] sctp_inq_push+0x51/0x70 [sctp]
   [<ffffffffc099732b>] sctp_rcv+0xa8b/0xbd0 [sctp]

As it shows, the first sctp_do_sm() running under atomic context (NET_RX
softirq) invoked sctp_primitive_ASCONF() that uses GFP_KERNEL flag later,
and this flag is supposed to be used in non-atomic context only. Besides,
sctp_do_sm() was called recursively, which is not expected.

Vlad tried to fix this recursive call in Commit c0786693404c ("sctp: Fix
oops when sending queued ASCONF chunks") by introducing a new command
SCTP_CMD_SEND_NEXT_ASCONF. But it didn't work as this command is still
used in the first sctp_do_sm() call, and sctp_primitive_ASCONF() will
be called in this command again.

To avoid calling sctp_do_sm() recursively, we send the next queued ASCONF
not by sctp_primitive_ASCONF(), but by sctp_sf_do_prm_asconf() in the 1st
sctp_do_sm() directly.

Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 include/net/sctp/command.h |    1 -
 net/sctp/sm_sideeffect.c   |   29 -----------------------------
 net/sctp/sm_statefuns.c    |   35 +++++++++++++++++++++++++++--------
 3 files changed, 27 insertions(+), 38 deletions(-)

--- a/include/net/sctp/command.h
+++ b/include/net/sctp/command.h
@@ -105,7 +105,6 @@ enum sctp_verb {
 	SCTP_CMD_T1_RETRAN,	 /* Mark for retransmission after T1 timeout  */
 	SCTP_CMD_UPDATE_INITTAG, /* Update peer inittag */
 	SCTP_CMD_SEND_MSG,	 /* Send the whole use message */
-	SCTP_CMD_SEND_NEXT_ASCONF, /* Send the next ASCONF after ACK */
 	SCTP_CMD_PURGE_ASCONF_QUEUE, /* Purge all asconf queues.*/
 	SCTP_CMD_SET_ASOC,	 /* Restore association context */
 	SCTP_CMD_LAST
--- a/net/sctp/sm_sideeffect.c
+++ b/net/sctp/sm_sideeffect.c
@@ -1112,32 +1112,6 @@ static void sctp_cmd_send_msg(struct sct
 }
 
 
-/* Sent the next ASCONF packet currently stored in the association.
- * This happens after the ASCONF_ACK was succeffully processed.
- */
-static void sctp_cmd_send_asconf(struct sctp_association *asoc)
-{
-	struct net *net = sock_net(asoc->base.sk);
-
-	/* Send the next asconf chunk from the addip chunk
-	 * queue.
-	 */
-	if (!list_empty(&asoc->addip_chunk_list)) {
-		struct list_head *entry = asoc->addip_chunk_list.next;
-		struct sctp_chunk *asconf = list_entry(entry,
-						struct sctp_chunk, list);
-		list_del_init(entry);
-
-		/* Hold the chunk until an ASCONF_ACK is received. */
-		sctp_chunk_hold(asconf);
-		if (sctp_primitive_ASCONF(net, asoc, asconf))
-			sctp_chunk_free(asconf);
-		else
-			asoc->addip_last_asconf = asconf;
-	}
-}
-
-
 /* These three macros allow us to pull the debugging code out of the
  * main flow of sctp_do_sm() to keep attention focused on the real
  * functionality there.
@@ -1783,9 +1757,6 @@ static int sctp_cmd_interpreter(enum sct
 			}
 			sctp_cmd_send_msg(asoc, cmd->obj.msg, gfp);
 			break;
-		case SCTP_CMD_SEND_NEXT_ASCONF:
-			sctp_cmd_send_asconf(asoc);
-			break;
 		case SCTP_CMD_PURGE_ASCONF_QUEUE:
 			sctp_asconf_queue_teardown(asoc);
 			break;
--- a/net/sctp/sm_statefuns.c
+++ b/net/sctp/sm_statefuns.c
@@ -3824,6 +3824,29 @@ enum sctp_disposition sctp_sf_do_asconf(
 	return SCTP_DISPOSITION_CONSUME;
 }
 
+static enum sctp_disposition sctp_send_next_asconf(
+					struct net *net,
+					const struct sctp_endpoint *ep,
+					struct sctp_association *asoc,
+					const union sctp_subtype type,
+					struct sctp_cmd_seq *commands)
+{
+	struct sctp_chunk *asconf;
+	struct list_head *entry;
+
+	if (list_empty(&asoc->addip_chunk_list))
+		return SCTP_DISPOSITION_CONSUME;
+
+	entry = asoc->addip_chunk_list.next;
+	asconf = list_entry(entry, struct sctp_chunk, list);
+
+	list_del_init(entry);
+	sctp_chunk_hold(asconf);
+	asoc->addip_last_asconf = asconf;
+
+	return sctp_sf_do_prm_asconf(net, ep, asoc, type, asconf, commands);
+}
+
 /*
  * ADDIP Section 4.3 General rules for address manipulation
  * When building TLV parameters for the ASCONF Chunk that will add or
@@ -3915,14 +3938,10 @@ enum sctp_disposition sctp_sf_do_asconf_
 				SCTP_TO(SCTP_EVENT_TIMEOUT_T4_RTO));
 
 		if (!sctp_process_asconf_ack((struct sctp_association *)asoc,
-					     asconf_ack)) {
-			/* Successfully processed ASCONF_ACK.  We can
-			 * release the next asconf if we have one.
-			 */
-			sctp_add_cmd_sf(commands, SCTP_CMD_SEND_NEXT_ASCONF,
-					SCTP_NULL());
-			return SCTP_DISPOSITION_CONSUME;
-		}
+					     asconf_ack))
+			return sctp_send_next_asconf(net, ep,
+					(struct sctp_association *)asoc,
+							type, commands);
 
 		abort = sctp_make_abort(asoc, asconf_ack,
 					sizeof(struct sctp_errhdr));

[PATCH 5.0 13/32] selftests: fib_rule_tests: print the result and return 1 if any tests failed

[Greg Kroah-Hartman]

From: Hangbin Liu <liuhangbin@gmail.com>

[ Upstream commit f68d7c44e76532e46f292ad941aa3706cb9e6e40 ]

Fixes: 65b2b4939a64 ("selftests: net: initial fib rule tests")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 tools/testing/selftests/net/fib_rule_tests.sh |    6 ++++++
 1 file changed, 6 insertions(+)

--- a/tools/testing/selftests/net/fib_rule_tests.sh
+++ b/tools/testing/selftests/net/fib_rule_tests.sh
@@ -27,6 +27,7 @@ log_test()
 		nsuccess=$((nsuccess+1))
 		printf "\n    TEST: %-50s  [ OK ]\n" "${msg}"
 	else
+		ret=1
 		nfail=$((nfail+1))
 		printf "\n    TEST: %-50s  [FAIL]\n" "${msg}"
 		if [ "${PAUSE_ON_FAIL}" = "yes" ]; then
@@ -245,4 +246,9 @@ setup
 run_fibrule_tests
 cleanup
 
+if [ "$TESTS" != "none" ]; then
+	printf "\nTests passed: %3d\n" ${nsuccess}
+	printf "Tests failed: %3d\n"   ${nfail}
+fi
+
 exit $ret

[PATCH 5.0 14/32] packet: validate msg_namelen in send directly

[Greg Kroah-Hartman]

From: Willem de Bruijn <willemb@google.com>

[ Upstream commit 486efdc8f6ce802b27e15921d2353cc740c55451 ]

Packet sockets in datagram mode take a destination address. Verify its
length before passing to dev_hard_header.

Prior to 2.6.14-rc3, the send code ignored sll_halen. This is
established behavior. Directly compare msg_namelen to dev->addr_len.

Change v1->v2: initialize addr in all paths

Fixes: 6b8d95f1795c4 ("packet: validate address length if non-zero")
Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/packet/af_packet.c |   24 ++++++++++++++----------
 1 file changed, 14 insertions(+), 10 deletions(-)

--- a/net/packet/af_packet.c
+++ b/net/packet/af_packet.c
@@ -2603,8 +2603,8 @@ static int tpacket_snd(struct packet_soc
 	void *ph;
 	DECLARE_SOCKADDR(struct sockaddr_ll *, saddr, msg->msg_name);
 	bool need_wait = !(msg->msg_flags & MSG_DONTWAIT);
+	unsigned char *addr = NULL;
 	int tp_len, size_max;
-	unsigned char *addr;
 	void *data;
 	int len_sum = 0;
 	int status = TP_STATUS_AVAILABLE;
@@ -2615,7 +2615,6 @@ static int tpacket_snd(struct packet_soc
 	if (likely(saddr == NULL)) {
 		dev	= packet_cached_dev_get(po);
 		proto	= po->num;
-		addr	= NULL;
 	} else {
 		err = -EINVAL;
 		if (msg->msg_namelen < sizeof(struct sockaddr_ll))
@@ -2625,10 +2624,13 @@ static int tpacket_snd(struct packet_soc
 						sll_addr)))
 			goto out;
 		proto	= saddr->sll_protocol;
-		addr	= saddr->sll_halen ? saddr->sll_addr : NULL;
 		dev = dev_get_by_index(sock_net(&po->sk), saddr->sll_ifindex);
-		if (addr && dev && saddr->sll_halen < dev->addr_len)
-			goto out_put;
+		if (po->sk.sk_socket->type == SOCK_DGRAM) {
+			if (dev && msg->msg_namelen < dev->addr_len +
+				   offsetof(struct sockaddr_ll, sll_addr))
+				goto out_put;
+			addr = saddr->sll_addr;
+		}
 	}
 
 	err = -ENXIO;
@@ -2800,7 +2802,7 @@ static int packet_snd(struct socket *soc
 	struct sk_buff *skb;
 	struct net_device *dev;
 	__be16 proto;
-	unsigned char *addr;
+	unsigned char *addr = NULL;
 	int err, reserve = 0;
 	struct sockcm_cookie sockc;
 	struct virtio_net_hdr vnet_hdr = { 0 };
@@ -2817,7 +2819,6 @@ static int packet_snd(struct socket *soc
 	if (likely(saddr == NULL)) {
 		dev	= packet_cached_dev_get(po);
 		proto	= po->num;
-		addr	= NULL;
 	} else {
 		err = -EINVAL;
 		if (msg->msg_namelen < sizeof(struct sockaddr_ll))
@@ -2825,10 +2826,13 @@ static int packet_snd(struct socket *soc
 		if (msg->msg_namelen < (saddr->sll_halen + offsetof(struct sockaddr_ll, sll_addr)))
 			goto out;
 		proto	= saddr->sll_protocol;
-		addr	= saddr->sll_halen ? saddr->sll_addr : NULL;
 		dev = dev_get_by_index(sock_net(sk), saddr->sll_ifindex);
-		if (addr && dev && saddr->sll_halen < dev->addr_len)
-			goto out_unlock;
+		if (sock->type == SOCK_DGRAM) {
+			if (dev && msg->msg_namelen < dev->addr_len +
+				   offsetof(struct sockaddr_ll, sll_addr))
+				goto out_unlock;
+			addr = saddr->sll_addr;
+		}
 	}
 
 	err = -ENXIO;

[PATCH 5.0 15/32] packet: in recvmsg msg_name return at least sizeof sockaddr_ll

[Greg Kroah-Hartman]

From: Willem de Bruijn <willemb@google.com>

[ Upstream commit b2cf86e1563e33a14a1c69b3e508d15dc12f804c ]

Packet send checks that msg_name is at least sizeof sockaddr_ll.
Packet recv must return at least this length, so that its output
can be passed unmodified to packet send.

This ceased to be true since adding support for lladdr longer than
sll_addr. Since, the return value uses true address length.

Always return at least sizeof sockaddr_ll, even if address length
is shorter. Zero the padding bytes.

Change v1->v2: do not overwrite zeroed padding again. use copy_len.

Fixes: 0fb375fb9b93 ("[AF_PACKET]: Allow for > 8 byte hardware addresses.")
Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/packet/af_packet.c |   13 +++++++++++--
 1 file changed, 11 insertions(+), 2 deletions(-)

--- a/net/packet/af_packet.c
+++ b/net/packet/af_packet.c
@@ -3349,20 +3349,29 @@ static int packet_recvmsg(struct socket
 	sock_recv_ts_and_drops(msg, sk, skb);
 
 	if (msg->msg_name) {
+		int copy_len;
+
 		/* If the address length field is there to be filled
 		 * in, we fill it in now.
 		 */
 		if (sock->type == SOCK_PACKET) {
 			__sockaddr_check_size(sizeof(struct sockaddr_pkt));
 			msg->msg_namelen = sizeof(struct sockaddr_pkt);
+			copy_len = msg->msg_namelen;
 		} else {
 			struct sockaddr_ll *sll = &PACKET_SKB_CB(skb)->sa.ll;
 
 			msg->msg_namelen = sll->sll_halen +
 				offsetof(struct sockaddr_ll, sll_addr);
+			copy_len = msg->msg_namelen;
+			if (msg->msg_namelen < sizeof(struct sockaddr_ll)) {
+				memset(msg->msg_name +
+				       offsetof(struct sockaddr_ll, sll_addr),
+				       0, sizeof(sll->sll_addr));
+				msg->msg_namelen = sizeof(struct sockaddr_ll);
+			}
 		}
-		memcpy(msg->msg_name, &PACKET_SKB_CB(skb)->sa,
-		       msg->msg_namelen);
+		memcpy(msg->msg_name, &PACKET_SKB_CB(skb)->sa, copy_len);
 	}
 
 	if (pkt_sk(sk)->auxdata) {

[PATCH 5.0 16/32] selftests: fib_rule_tests: Fix icmp proto with ipv6

[Greg Kroah-Hartman]

From: David Ahern <dsahern@gmail.com>

[ Upstream commit 15d55bae4e3c43cd9f87fd93c73a263e172d34e1 ]

A recent commit returns an error if icmp is used as the ip-proto for
IPv6 fib rules. Update fib_rule_tests to send ipv6-icmp instead of icmp.

Fixes: 5e1a99eae8499 ("ipv4: Add ICMPv6 support when parse route ipproto")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 tools/testing/selftests/net/fib_rule_tests.sh |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/tools/testing/selftests/net/fib_rule_tests.sh
+++ b/tools/testing/selftests/net/fib_rule_tests.sh
@@ -148,8 +148,8 @@ fib_rule6_test()
 
 	fib_check_iproute_support "ipproto" "ipproto"
 	if [ $? -eq 0 ]; then
-		match="ipproto icmp"
-		fib_rule6_test_match_n_redirect "$match" "$match" "ipproto icmp match"
+		match="ipproto ipv6-icmp"
+		fib_rule6_test_match_n_redirect "$match" "$match" "ipproto ipv6-icmp match"
 	fi
 }
 

[PATCH 5.0 17/32] tcp: add sanity tests in tcp_add_backlog()

[Greg Kroah-Hartman]

From: Eric Dumazet <edumazet@google.com>

[ Upstream commit ca2fe2956acef2f87f6c55549874fdd2e92d9824 ]

Richard and Bruno both reported that my commit added a bug,
and Bruno was able to determine the problem came when a segment
wih a FIN packet was coalesced to a prior one in tcp backlog queue.

It turns out the header prediction in tcp_rcv_established()
looks back to TCP headers in the packet, not in the metadata
(aka TCP_SKB_CB(skb)->tcp_flags)

The fast path in tcp_rcv_established() is not supposed to
handle a FIN flag (it does not call tcp_fin())

Therefore we need to make sure to propagate the FIN flag,
so that the coalesced packet does not go through the fast path,
the same than a GRO packet carrying a FIN flag.

While we are at it, make sure we do not coalesce packets with
RST or SYN, or if they do not have ACK set.

Many thanks to Richard and Bruno for pinpointing the bad commit,
and to Richard for providing a first version of the fix.

Fixes: 4f693b55c3d2 ("tcp: implement coalescing on backlog queue")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Reported-by: Bruno Prémont <bonbons@sysophe.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv4/tcp_ipv4.c |   13 ++++++++++++-
 1 file changed, 12 insertions(+), 1 deletion(-)

--- a/net/ipv4/tcp_ipv4.c
+++ b/net/ipv4/tcp_ipv4.c
@@ -1673,7 +1673,9 @@ bool tcp_add_backlog(struct sock *sk, st
 	if (TCP_SKB_CB(tail)->end_seq != TCP_SKB_CB(skb)->seq ||
 	    TCP_SKB_CB(tail)->ip_dsfield != TCP_SKB_CB(skb)->ip_dsfield ||
 	    ((TCP_SKB_CB(tail)->tcp_flags |
-	      TCP_SKB_CB(skb)->tcp_flags) & TCPHDR_URG) ||
+	      TCP_SKB_CB(skb)->tcp_flags) & (TCPHDR_SYN | TCPHDR_RST | TCPHDR_URG)) ||
+	    !((TCP_SKB_CB(tail)->tcp_flags &
+	      TCP_SKB_CB(skb)->tcp_flags) & TCPHDR_ACK) ||
 	    ((TCP_SKB_CB(tail)->tcp_flags ^
 	      TCP_SKB_CB(skb)->tcp_flags) & (TCPHDR_ECE | TCPHDR_CWR)) ||
 #ifdef CONFIG_TLS_DEVICE
@@ -1692,6 +1694,15 @@ bool tcp_add_backlog(struct sock *sk, st
 		if (after(TCP_SKB_CB(skb)->ack_seq, TCP_SKB_CB(tail)->ack_seq))
 			TCP_SKB_CB(tail)->ack_seq = TCP_SKB_CB(skb)->ack_seq;
 
+		/* We have to update both TCP_SKB_CB(tail)->tcp_flags and
+		 * thtail->fin, so that the fast path in tcp_rcv_established()
+		 * is not entered if we append a packet with a FIN.
+		 * SYN, RST, URG are not present.
+		 * ACK is set on both packets.
+		 * PSH : we do not really care in TCP stack,
+		 *       at least for 'GRO' packets.
+		 */
+		thtail->fin |= th->fin;
 		TCP_SKB_CB(tail)->tcp_flags |= TCP_SKB_CB(skb)->tcp_flags;
 
 		if (TCP_SKB_CB(skb)->has_rxtstamp) {

[PATCH 5.0 18/32] udp: fix GRO reception in case of length mismatch

[Greg Kroah-Hartman]

From: Paolo Abeni <pabeni@redhat.com>

[ Upstream commit 21f1b8a6636c4dbde4aa1ec0343f42eaf653ffcc ]

Currently, the UDP GRO code path does bad things on some edge
conditions - Aggregation can happen even on packet with different
lengths.

Fix the above by rewriting the 'complete' condition for GRO
packets. While at it, note explicitly that we allow merging the
first packet per burst below gso_size.

Reported-by: Sean Tong <seantong114@gmail.com>
Fixes: e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv4/udp_offload.c |    9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

--- a/net/ipv4/udp_offload.c
+++ b/net/ipv4/udp_offload.c
@@ -377,13 +377,14 @@ static struct sk_buff *udp_gro_receive_s
 
 		/* Terminate the flow on len mismatch or if it grow "too much".
 		 * Under small packet flood GRO count could elsewhere grow a lot
-		 * leading to execessive truesize values
+		 * leading to execessive truesize values.
+		 * On len mismatch merge the first packet shorter than gso_size,
+		 * otherwise complete the GRO packet.
 		 */
-		if (!skb_gro_receive(p, skb) &&
+		if (uh->len > uh2->len || skb_gro_receive(p, skb) ||
+		    uh->len != uh2->len ||
 		    NAPI_GRO_CB(p)->count >= UDP_GRO_CNT_MAX)
 			pp = p;
-		else if (uh->len != uh2->len)
-			pp = p;
 
 		return pp;
 	}

[PATCH 5.0 19/32] udp: fix GRO packet of death

[Greg Kroah-Hartman]

From: Eric Dumazet <edumazet@google.com>

[ Upstream commit 4dd2b82d5adfbe0b1587ccad7a8f76d826120f37 ]

syzbot was able to crash host by sending UDP packets with a 0 payload.

TCP does not have this issue since we do not aggregate packets without
payload.

Since dev_gro_receive() sets gso_size based on skb_gro_len(skb)
it seems not worth trying to cope with padded packets.

BUG: KASAN: slab-out-of-bounds in skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
Read of size 16 at addr ffff88808893fff0 by task syz-executor612/7889

CPU: 0 PID: 7889 Comm: syz-executor612 Not tainted 5.1.0-rc7+ #96
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x172/0x1f0 lib/dump_stack.c:113
 print_address_description.cold+0x7c/0x20d mm/kasan/report.c:187
 kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
 __asan_report_load16_noabort+0x14/0x20 mm/kasan/generic_report.c:133
 skb_gro_receive+0xf5f/0x10e0 net/core/skbuff.c:3826
 udp_gro_receive_segment net/ipv4/udp_offload.c:382 [inline]
 call_gro_receive include/linux/netdevice.h:2349 [inline]
 udp_gro_receive+0xb61/0xfd0 net/ipv4/udp_offload.c:414
 udp4_gro_receive+0x763/0xeb0 net/ipv4/udp_offload.c:478
 inet_gro_receive+0xe72/0x1110 net/ipv4/af_inet.c:1510
 dev_gro_receive+0x1cd0/0x23c0 net/core/dev.c:5581
 napi_gro_frags+0x36b/0xd10 net/core/dev.c:5843
 tun_get_user+0x2f24/0x3fb0 drivers/net/tun.c:1981
 tun_chr_write_iter+0xbd/0x156 drivers/net/tun.c:2027
 call_write_iter include/linux/fs.h:1866 [inline]
 do_iter_readv_writev+0x5e1/0x8e0 fs/read_write.c:681
 do_iter_write fs/read_write.c:957 [inline]
 do_iter_write+0x184/0x610 fs/read_write.c:938
 vfs_writev+0x1b3/0x2f0 fs/read_write.c:1002
 do_writev+0x15e/0x370 fs/read_write.c:1037
 __do_sys_writev fs/read_write.c:1110 [inline]
 __se_sys_writev fs/read_write.c:1107 [inline]
 __x64_sys_writev+0x75/0xb0 fs/read_write.c:1107
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x441cc0
Code: 05 48 3d 01 f0 ff ff 0f 83 9d 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 83 3d 51 93 29 00 00 75 14 b8 14 00 00 00 0f 05 <48> 3d 01 f0 ff ff 0f 83 74 09 fc ff c3 48 83 ec 08 e8 ba 2b 00 00
RSP: 002b:00007ffe8c716118 EFLAGS: 00000246 ORIG_RAX: 0000000000000014
RAX: ffffffffffffffda RBX: 00007ffe8c716150 RCX: 0000000000441cc0
RDX: 0000000000000001 RSI: 00007ffe8c716170 RDI: 00000000000000f0
RBP: 0000000000000000 R08: 000000000000ffff R09: 0000000000a64668
R10: 0000000020000040 R11: 0000000000000246 R12: 000000000000c2d9
R13: 0000000000402b50 R14: 0000000000000000 R15: 0000000000000000

Allocated by task 5143:
 save_stack+0x45/0xd0 mm/kasan/common.c:75
 set_track mm/kasan/common.c:87 [inline]
 __kasan_kmalloc mm/kasan/common.c:497 [inline]
 __kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:470
 kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:505
 slab_post_alloc_hook mm/slab.h:437 [inline]
 slab_alloc mm/slab.c:3393 [inline]
 kmem_cache_alloc+0x11a/0x6f0 mm/slab.c:3555
 mm_alloc+0x1d/0xd0 kernel/fork.c:1030
 bprm_mm_init fs/exec.c:363 [inline]
 __do_execve_file.isra.0+0xaa3/0x23f0 fs/exec.c:1791
 do_execveat_common fs/exec.c:1865 [inline]
 do_execve fs/exec.c:1882 [inline]
 __do_sys_execve fs/exec.c:1958 [inline]
 __se_sys_execve fs/exec.c:1953 [inline]
 __x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

Freed by task 5351:
 save_stack+0x45/0xd0 mm/kasan/common.c:75
 set_track mm/kasan/common.c:87 [inline]
 __kasan_slab_free+0x102/0x150 mm/kasan/common.c:459
 kasan_slab_free+0xe/0x10 mm/kasan/common.c:467
 __cache_free mm/slab.c:3499 [inline]
 kmem_cache_free+0x86/0x260 mm/slab.c:3765
 __mmdrop+0x238/0x320 kernel/fork.c:677
 mmdrop include/linux/sched/mm.h:49 [inline]
 finish_task_switch+0x47b/0x780 kernel/sched/core.c:2746
 context_switch kernel/sched/core.c:2880 [inline]
 __schedule+0x81b/0x1cc0 kernel/sched/core.c:3518
 preempt_schedule_irq+0xb5/0x140 kernel/sched/core.c:3745
 retint_kernel+0x1b/0x2d
 arch_local_irq_restore arch/x86/include/asm/paravirt.h:767 [inline]
 kmem_cache_free+0xab/0x260 mm/slab.c:3766
 anon_vma_chain_free mm/rmap.c:134 [inline]
 unlink_anon_vmas+0x2ba/0x870 mm/rmap.c:401
 free_pgtables+0x1af/0x2f0 mm/memory.c:394
 exit_mmap+0x2d1/0x530 mm/mmap.c:3144
 __mmput kernel/fork.c:1046 [inline]
 mmput+0x15f/0x4c0 kernel/fork.c:1067
 exec_mmap fs/exec.c:1046 [inline]
 flush_old_exec+0x8d9/0x1c20 fs/exec.c:1279
 load_elf_binary+0x9bc/0x53f0 fs/binfmt_elf.c:864
 search_binary_handler fs/exec.c:1656 [inline]
 search_binary_handler+0x17f/0x570 fs/exec.c:1634
 exec_binprm fs/exec.c:1698 [inline]
 __do_execve_file.isra.0+0x1394/0x23f0 fs/exec.c:1818
 do_execveat_common fs/exec.c:1865 [inline]
 do_execve fs/exec.c:1882 [inline]
 __do_sys_execve fs/exec.c:1958 [inline]
 __se_sys_execve fs/exec.c:1953 [inline]
 __x64_sys_execve+0x8f/0xc0 fs/exec.c:1953
 do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
 entry_SYSCALL_64_after_hwframe+0x49/0xbe

The buggy address belongs to the object at ffff88808893f7c0
 which belongs to the cache mm_struct of size 1496
The buggy address is located 600 bytes to the right of
 1496-byte region [ffff88808893f7c0, ffff88808893fd98)
The buggy address belongs to the page:
page:ffffea0002224f80 count:1 mapcount:0 mapping:ffff88821bc40ac0 index:0xffff88808893f7c0 compound_mapcount: 0
flags: 0x1fffc0000010200(slab|head)
raw: 01fffc0000010200 ffffea00025b4f08 ffffea00027b9d08 ffff88821bc40ac0
raw: ffff88808893f7c0 ffff88808893e440 0000000100000001 0000000000000000
page dumped because: kasan: bad access detected

Memory state around the buggy address:
 ffff88808893fe80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffff88808893ff00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffff88808893ff80: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
                                                             ^
 ffff888088940000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
 ffff888088940080: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

Fixes: e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/ipv4/udp_offload.c |   13 ++++++++++---
 1 file changed, 10 insertions(+), 3 deletions(-)

--- a/net/ipv4/udp_offload.c
+++ b/net/ipv4/udp_offload.c
@@ -352,6 +352,7 @@ static struct sk_buff *udp_gro_receive_s
 	struct sk_buff *pp = NULL;
 	struct udphdr *uh2;
 	struct sk_buff *p;
+	unsigned int ulen;
 
 	/* requires non zero csum, for symmetry with GSO */
 	if (!uh->check) {
@@ -359,6 +360,12 @@ static struct sk_buff *udp_gro_receive_s
 		return NULL;
 	}
 
+	/* Do not deal with padded or malicious packets, sorry ! */
+	ulen = ntohs(uh->len);
+	if (ulen <= sizeof(*uh) || ulen != skb_gro_len(skb)) {
+		NAPI_GRO_CB(skb)->flush = 1;
+		return NULL;
+	}
 	/* pull encapsulating udp header */
 	skb_gro_pull(skb, sizeof(struct udphdr));
 	skb_gro_postpull_rcsum(skb, uh, sizeof(struct udphdr));
@@ -377,12 +384,12 @@ static struct sk_buff *udp_gro_receive_s
 
 		/* Terminate the flow on len mismatch or if it grow "too much".
 		 * Under small packet flood GRO count could elsewhere grow a lot
-		 * leading to execessive truesize values.
+		 * leading to excessive truesize values.
 		 * On len mismatch merge the first packet shorter than gso_size,
 		 * otherwise complete the GRO packet.
 		 */
-		if (uh->len > uh2->len || skb_gro_receive(p, skb) ||
-		    uh->len != uh2->len ||
+		if (ulen > ntohs(uh2->len) || skb_gro_receive(p, skb) ||
+		    ulen != ntohs(uh2->len) ||
 		    NAPI_GRO_CB(p)->count >= UDP_GRO_CNT_MAX)
 			pp = p;
 

[PATCH 5.0 20/32] bnxt_en: Improve multicast address setup logic.

[Greg Kroah-Hartman]

From: Michael Chan <michael.chan@broadcom.com>

[ Upstream commit b4e30e8e7ea1d1e35ffd64ca46f7d9a7f227b4bf ]

The driver builds a list of multicast addresses and sends it to the
firmware when the driver's ndo_set_rx_mode() is called.  In rare
cases, the firmware can fail this call if internal resources to
add multicast addresses are exhausted.  In that case, we should
try the call again by setting the ALL_MCAST flag which is more
guaranteed to succeed.

Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/broadcom/bnxt/bnxt.c |    9 ++++++++-
 1 file changed, 8 insertions(+), 1 deletion(-)

--- a/drivers/net/ethernet/broadcom/bnxt/bnxt.c
+++ b/drivers/net/ethernet/broadcom/bnxt/bnxt.c
@@ -8889,8 +8889,15 @@ static int bnxt_cfg_rx_mode(struct bnxt
 
 skip_uc:
 	rc = bnxt_hwrm_cfa_l2_set_rx_mask(bp, 0);
+	if (rc && vnic->mc_list_count) {
+		netdev_info(bp->dev, "Failed setting MC filters rc: %d, turning on ALL_MCAST mode\n",
+			    rc);
+		vnic->rx_mask |= CFA_L2_SET_RX_MASK_REQ_MASK_ALL_MCAST;
+		vnic->mc_list_count = 0;
+		rc = bnxt_hwrm_cfa_l2_set_rx_mask(bp, 0);
+	}
 	if (rc)
-		netdev_err(bp->dev, "HWRM cfa l2 rx mask failure rc: %x\n",
+		netdev_err(bp->dev, "HWRM cfa l2 rx mask failure rc: %d\n",
 			   rc);
 
 	return rc;

[PATCH 5.0 21/32] bnxt_en: Free short FW command HWRM memory in error path in bnxt_init_one()

[Greg Kroah-Hartman]

From: Vasundhara Volam <vasundhara-v.volam@broadcom.com>

[ Upstream commit f9099d611449836a51a65f40ea7dc9cb5f2f665e ]

In the bnxt_init_one() error path, short FW command request memory
is not freed. This patch fixes it.

Fixes: e605db801bde ("bnxt_en: Support for Short Firmware Message")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/broadcom/bnxt/bnxt.c |    1 +
 1 file changed, 1 insertion(+)

--- a/drivers/net/ethernet/broadcom/bnxt/bnxt.c
+++ b/drivers/net/ethernet/broadcom/bnxt/bnxt.c
@@ -10632,6 +10632,7 @@ init_err_cleanup_tc:
 	bnxt_clear_int_mode(bp);
 
 init_err_pci_clean:
+	bnxt_free_hwrm_short_cmd_req(bp);
 	bnxt_free_hwrm_resources(bp);
 	bnxt_free_ctx_mem(bp);
 	kfree(bp->ctx);

[PATCH 5.0 22/32] bnxt_en: Fix possible crash in bnxt_hwrm_ring_free() under error conditions.

[Greg Kroah-Hartman]

From: Michael Chan <michael.chan@broadcom.com>

[ Upstream commit 1f83391bd6fc48f92f627b0ec0bce686d100c6a5 ]

If we encounter errors during open and proceed to clean up,
bnxt_hwrm_ring_free() may crash if the rings we try to free have never
been allocated.  bnxt_cp_ring_for_rx() or bnxt_cp_ring_for_tx()
may reference pointers that have not been allocated.

Fix it by checking for valid fw_ring_id first before calling
bnxt_cp_ring_for_rx() or bnxt_cp_ring_for_tx().

Fixes: 2c61d2117ecb ("bnxt_en: Add helper functions to get firmware CP ring ID.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/broadcom/bnxt/bnxt.c |   12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

--- a/drivers/net/ethernet/broadcom/bnxt/bnxt.c
+++ b/drivers/net/ethernet/broadcom/bnxt/bnxt.c
@@ -5131,10 +5131,10 @@ static void bnxt_hwrm_ring_free(struct b
 	for (i = 0; i < bp->tx_nr_rings; i++) {
 		struct bnxt_tx_ring_info *txr = &bp->tx_ring[i];
 		struct bnxt_ring_struct *ring = &txr->tx_ring_struct;
-		u32 cmpl_ring_id;
 
-		cmpl_ring_id = bnxt_cp_ring_for_tx(bp, txr);
 		if (ring->fw_ring_id != INVALID_HW_RING_ID) {
+			u32 cmpl_ring_id = bnxt_cp_ring_for_tx(bp, txr);
+
 			hwrm_ring_free_send_msg(bp, ring,
 						RING_FREE_REQ_RING_TYPE_TX,
 						close_path ? cmpl_ring_id :
@@ -5147,10 +5147,10 @@ static void bnxt_hwrm_ring_free(struct b
 		struct bnxt_rx_ring_info *rxr = &bp->rx_ring[i];
 		struct bnxt_ring_struct *ring = &rxr->rx_ring_struct;
 		u32 grp_idx = rxr->bnapi->index;
-		u32 cmpl_ring_id;
 
-		cmpl_ring_id = bnxt_cp_ring_for_rx(bp, rxr);
 		if (ring->fw_ring_id != INVALID_HW_RING_ID) {
+			u32 cmpl_ring_id = bnxt_cp_ring_for_rx(bp, rxr);
+
 			hwrm_ring_free_send_msg(bp, ring,
 						RING_FREE_REQ_RING_TYPE_RX,
 						close_path ? cmpl_ring_id :
@@ -5169,10 +5169,10 @@ static void bnxt_hwrm_ring_free(struct b
 		struct bnxt_rx_ring_info *rxr = &bp->rx_ring[i];
 		struct bnxt_ring_struct *ring = &rxr->rx_agg_ring_struct;
 		u32 grp_idx = rxr->bnapi->index;
-		u32 cmpl_ring_id;
 
-		cmpl_ring_id = bnxt_cp_ring_for_rx(bp, rxr);
 		if (ring->fw_ring_id != INVALID_HW_RING_ID) {
+			u32 cmpl_ring_id = bnxt_cp_ring_for_rx(bp, rxr);
+
 			hwrm_ring_free_send_msg(bp, ring, type,
 						close_path ? cmpl_ring_id :
 						INVALID_HW_RING_ID);

[PATCH 5.0 23/32] bnxt_en: Pass correct extended TX port statistics size to firmware.

[Greg Kroah-Hartman]

From: Michael Chan <michael.chan@broadcom.com>

[ Upstream commit ad361adf0d08f1135f3845c6b3a36be7cc0bfda5 ]

If driver determines that extended TX port statistics are not supported
or allocation of the data structure fails, make sure to pass 0 TX stats
size to firmware to disable it.  The firmware returned TX stats size should
also be set to 0 for consistency.  This will prevent
bnxt_get_ethtool_stats() from accessing the NULL TX stats pointer in
case there is mismatch between firmware and driver.

Fixes: 36e53349b60b ("bnxt_en: Add additional extended port statistics.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/broadcom/bnxt/bnxt.c |    8 ++++++--
 1 file changed, 6 insertions(+), 2 deletions(-)

--- a/drivers/net/ethernet/broadcom/bnxt/bnxt.c
+++ b/drivers/net/ethernet/broadcom/bnxt/bnxt.c
@@ -6745,6 +6745,7 @@ static int bnxt_hwrm_port_qstats_ext(str
 	struct hwrm_queue_pri2cos_qcfg_input req2 = {0};
 	struct hwrm_port_qstats_ext_input req = {0};
 	struct bnxt_pf_info *pf = &bp->pf;
+	u32 tx_stat_size;
 	int rc;
 
 	if (!(bp->flags & BNXT_FLAG_PORT_STATS_EXT))
@@ -6754,13 +6755,16 @@ static int bnxt_hwrm_port_qstats_ext(str
 	req.port_id = cpu_to_le16(pf->port_id);
 	req.rx_stat_size = cpu_to_le16(sizeof(struct rx_port_stats_ext));
 	req.rx_stat_host_addr = cpu_to_le64(bp->hw_rx_port_stats_ext_map);
-	req.tx_stat_size = cpu_to_le16(sizeof(struct tx_port_stats_ext));
+	tx_stat_size = bp->hw_tx_port_stats_ext ?
+		       sizeof(*bp->hw_tx_port_stats_ext) : 0;
+	req.tx_stat_size = cpu_to_le16(tx_stat_size);
 	req.tx_stat_host_addr = cpu_to_le64(bp->hw_tx_port_stats_ext_map);
 	mutex_lock(&bp->hwrm_cmd_lock);
 	rc = _hwrm_send_message(bp, &req, sizeof(req), HWRM_CMD_TIMEOUT);
 	if (!rc) {
 		bp->fw_rx_stats_ext_size = le16_to_cpu(resp->rx_stat_size) / 8;
-		bp->fw_tx_stats_ext_size = le16_to_cpu(resp->tx_stat_size) / 8;
+		bp->fw_tx_stats_ext_size = tx_stat_size ?
+			le16_to_cpu(resp->tx_stat_size) / 8 : 0;
 	} else {
 		bp->fw_rx_stats_ext_size = 0;
 		bp->fw_tx_stats_ext_size = 0;

[PATCH 5.0 24/32] bnxt_en: Fix statistics context reservation logic.

[Greg Kroah-Hartman]

From: Michael Chan <michael.chan@broadcom.com>

[ Upstream commit 3f93cd3f098e284c851acb89265ebe35b994a5c8 ]

In an earlier commit that fixes the number of stats contexts to
reserve for the RDMA driver, we added a function parameter to pass in
the number of stats contexts to all the relevant functions.  The passed
in parameter should have been used to set the enables field of the
firmware message.

Fixes: 780baad44f0f ("bnxt_en: Reserve 1 stat_ctx for RDMA driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/broadcom/bnxt/bnxt.c |   14 ++++++--------
 1 file changed, 6 insertions(+), 8 deletions(-)

--- a/drivers/net/ethernet/broadcom/bnxt/bnxt.c
+++ b/drivers/net/ethernet/broadcom/bnxt/bnxt.c
@@ -5311,17 +5311,16 @@ __bnxt_hwrm_reserve_pf_rings(struct bnxt
 	req->num_tx_rings = cpu_to_le16(tx_rings);
 	if (BNXT_NEW_RM(bp)) {
 		enables |= rx_rings ? FUNC_CFG_REQ_ENABLES_NUM_RX_RINGS : 0;
+		enables |= stats ? FUNC_CFG_REQ_ENABLES_NUM_STAT_CTXS : 0;
 		if (bp->flags & BNXT_FLAG_CHIP_P5) {
 			enables |= cp_rings ? FUNC_CFG_REQ_ENABLES_NUM_MSIX : 0;
 			enables |= tx_rings + ring_grps ?
-				   FUNC_CFG_REQ_ENABLES_NUM_CMPL_RINGS |
-				   FUNC_CFG_REQ_ENABLES_NUM_STAT_CTXS : 0;
+				   FUNC_CFG_REQ_ENABLES_NUM_CMPL_RINGS : 0;
 			enables |= rx_rings ?
 				FUNC_CFG_REQ_ENABLES_NUM_RSSCOS_CTXS : 0;
 		} else {
 			enables |= cp_rings ?
-				   FUNC_CFG_REQ_ENABLES_NUM_CMPL_RINGS |
-				   FUNC_CFG_REQ_ENABLES_NUM_STAT_CTXS : 0;
+				   FUNC_CFG_REQ_ENABLES_NUM_CMPL_RINGS : 0;
 			enables |= ring_grps ?
 				   FUNC_CFG_REQ_ENABLES_NUM_HW_RING_GRPS |
 				   FUNC_CFG_REQ_ENABLES_NUM_RSSCOS_CTXS : 0;
@@ -5361,14 +5360,13 @@ __bnxt_hwrm_reserve_vf_rings(struct bnxt
 	enables |= tx_rings ? FUNC_VF_CFG_REQ_ENABLES_NUM_TX_RINGS : 0;
 	enables |= rx_rings ? FUNC_VF_CFG_REQ_ENABLES_NUM_RX_RINGS |
 			      FUNC_VF_CFG_REQ_ENABLES_NUM_RSSCOS_CTXS : 0;
+	enables |= stats ? FUNC_VF_CFG_REQ_ENABLES_NUM_STAT_CTXS : 0;
 	if (bp->flags & BNXT_FLAG_CHIP_P5) {
 		enables |= tx_rings + ring_grps ?
-			   FUNC_VF_CFG_REQ_ENABLES_NUM_CMPL_RINGS |
-			   FUNC_VF_CFG_REQ_ENABLES_NUM_STAT_CTXS : 0;
+			   FUNC_VF_CFG_REQ_ENABLES_NUM_CMPL_RINGS : 0;
 	} else {
 		enables |= cp_rings ?
-			   FUNC_VF_CFG_REQ_ENABLES_NUM_CMPL_RINGS |
-			   FUNC_VF_CFG_REQ_ENABLES_NUM_STAT_CTXS : 0;
+			   FUNC_VF_CFG_REQ_ENABLES_NUM_CMPL_RINGS : 0;
 		enables |= ring_grps ?
 			   FUNC_VF_CFG_REQ_ENABLES_NUM_HW_RING_GRPS : 0;
 	}

[PATCH 5.0 25/32] bnxt_en: Fix uninitialized variable usage in bnxt_rx_pkt().

[Greg Kroah-Hartman]

From: Michael Chan <michael.chan@broadcom.com>

[ Upstream commit 0b397b17a4120cb80f7bf89eb30587b3dd9b0d1d ]

In bnxt_rx_pkt(), if the driver encounters BD errors, it will recycle
the buffers and jump to the end where the uninitailized variable "len"
is referenced.  Fix it by adding a new jump label that will skip
the length update.  This is the most correct fix since the length
may not be valid when we get this type of error.

Fixes: 6a8788f25625 ("bnxt_en: add support for software dynamic interrupt moderation")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 drivers/net/ethernet/broadcom/bnxt/bnxt.c |    9 +++++----
 1 file changed, 5 insertions(+), 4 deletions(-)

--- a/drivers/net/ethernet/broadcom/bnxt/bnxt.c
+++ b/drivers/net/ethernet/broadcom/bnxt/bnxt.c
@@ -1621,7 +1621,7 @@ static int bnxt_rx_pkt(struct bnxt *bp,
 			netdev_warn(bp->dev, "RX buffer error %x\n", rx_err);
 			bnxt_sched_reset(bp, rxr);
 		}
-		goto next_rx;
+		goto next_rx_no_len;
 	}
 
 	len = le32_to_cpu(rxcmp->rx_cmp_len_flags_type) >> RX_CMP_LEN_SHIFT;
@@ -1702,12 +1702,13 @@ static int bnxt_rx_pkt(struct bnxt *bp,
 	rc = 1;
 
 next_rx:
-	rxr->rx_prod = NEXT_RX(prod);
-	rxr->rx_next_cons = NEXT_RX(cons);
-
 	cpr->rx_packets += 1;
 	cpr->rx_bytes += len;
 
+next_rx_no_len:
+	rxr->rx_prod = NEXT_RX(prod);
+	rxr->rx_next_cons = NEXT_RX(cons);
+
 next_rx_no_prod_no_len:
 	*raw_cons = tmp_raw_cons;
 

[PATCH 5.0 26/32] net/tls: dont copy negative amounts of data in reencrypt

[Greg Kroah-Hartman]

From: Jakub Kicinski <jakub.kicinski@netronome.com>

[ Upstream commit 97e1caa517e22d62a283b876fb8aa5f4672c83dd ]

There is no guarantee the record starts before the skb frags.
If we don't check for this condition copy amount will get
negative, leading to reads and writes to random memory locations.
Familiar hilarity ensues.

Fixes: 4799ac81e52a ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/tls/tls_device.c |   14 ++++++++------
 1 file changed, 8 insertions(+), 6 deletions(-)

--- a/net/tls/tls_device.c
+++ b/net/tls/tls_device.c
@@ -610,14 +610,16 @@ static int tls_device_reencrypt(struct s
 	else
 		err = 0;
 
-	copy = min_t(int, skb_pagelen(skb) - offset,
-		     rxm->full_len - TLS_CIPHER_AES_GCM_128_TAG_SIZE);
+	if (skb_pagelen(skb) > offset) {
+		copy = min_t(int, skb_pagelen(skb) - offset,
+			     rxm->full_len - TLS_CIPHER_AES_GCM_128_TAG_SIZE);
 
-	if (skb->decrypted)
-		skb_store_bits(skb, offset, buf, copy);
+		if (skb->decrypted)
+			skb_store_bits(skb, offset, buf, copy);
 
-	offset += copy;
-	buf += copy;
+		offset += copy;
+		buf += copy;
+	}
 
 	skb_walk_frags(skb, skb_iter) {
 		copy = min_t(int, skb_iter->len,

[PATCH 5.0 27/32] net/tls: fix copy to fragments in reencrypt

[Greg Kroah-Hartman]

From: Jakub Kicinski <jakub.kicinski@netronome.com>

[ Upstream commit eb3d38d5adb520435d4e4af32529ccb13ccc9935 ]

Fragments may contain data from other records so we have to account
for that when we calculate the destination and max length of copy we
can perform.  Note that 'offset' is the offset within the message,
so it can't be passed as offset within the frag..

Here skb_store_bits() would have realised the call is wrong and
simply not copy data.

Fixes: 4799ac81e52a ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 net/tls/tls_device.c |   29 ++++++++++++++++++++++-------
 1 file changed, 22 insertions(+), 7 deletions(-)

--- a/net/tls/tls_device.c
+++ b/net/tls/tls_device.c
@@ -579,7 +579,7 @@ void handle_device_resync(struct sock *s
 static int tls_device_reencrypt(struct sock *sk, struct sk_buff *skb)
 {
 	struct strp_msg *rxm = strp_msg(skb);
-	int err = 0, offset = rxm->offset, copy, nsg;
+	int err = 0, offset = rxm->offset, copy, nsg, data_len, pos;
 	struct sk_buff *skb_iter, *unused;
 	struct scatterlist sg[1];
 	char *orig_buf, *buf;
@@ -610,9 +610,10 @@ static int tls_device_reencrypt(struct s
 	else
 		err = 0;
 
+	data_len = rxm->full_len - TLS_CIPHER_AES_GCM_128_TAG_SIZE;
+
 	if (skb_pagelen(skb) > offset) {
-		copy = min_t(int, skb_pagelen(skb) - offset,
-			     rxm->full_len - TLS_CIPHER_AES_GCM_128_TAG_SIZE);
+		copy = min_t(int, skb_pagelen(skb) - offset, data_len);
 
 		if (skb->decrypted)
 			skb_store_bits(skb, offset, buf, copy);
@@ -621,16 +622,30 @@ static int tls_device_reencrypt(struct s
 		buf += copy;
 	}
 
+	pos = skb_pagelen(skb);
 	skb_walk_frags(skb, skb_iter) {
-		copy = min_t(int, skb_iter->len,
-			     rxm->full_len - offset + rxm->offset -
-			     TLS_CIPHER_AES_GCM_128_TAG_SIZE);
+		int frag_pos;
+
+		/* Practically all frags must belong to msg if reencrypt
+		 * is needed with current strparser and coalescing logic,
+		 * but strparser may "get optimized", so let's be safe.
+		 */
+		if (pos + skb_iter->len <= offset)
+			goto done_with_frag;
+		if (pos >= data_len + rxm->offset)
+			break;
+
+		frag_pos = offset - pos;
+		copy = min_t(int, skb_iter->len - frag_pos,
+			     data_len + rxm->offset - offset);
 
 		if (skb_iter->decrypted)
-			skb_store_bits(skb_iter, offset, buf, copy);
+			skb_store_bits(skb_iter, frag_pos, buf, copy);
 
 		offset += copy;
 		buf += copy;
+done_with_frag:
+		pos += skb_iter->len;
 	}
 
 free_buf:

[PATCH 5.0 28/32] KVM: x86: Whitelist port 0x7e for pre-incrementing %rip

[Greg Kroah-Hartman]

From: Sean Christopherson <sean.j.christopherson@intel.com>

commit 8764ed55c9705e426d889ff16c26f398bba70b9b upstream.

KVM's recent bug fix to update %rip after emulating I/O broke userspace
that relied on the previous behavior of incrementing %rip prior to
exiting to userspace.  When running a Windows XP guest on AMD hardware,
Qemu may patch "OUT 0x7E" instructions in reaction to the OUT itself.
Because KVM's old behavior was to increment %rip before exiting to
userspace to handle the I/O, Qemu manually adjusted %rip to account for
the OUT instruction.

Arguably this is a userspace bug as KVM requires userspace to re-enter
the kernel to complete instruction emulation before taking any other
actions.  That being said, this is a bit of a grey area and breaking
userspace that has worked for many years is bad.

Pre-increment %rip on OUT to port 0x7e before exiting to userspace to
hack around the issue.

Fixes: 45def77ebf79e ("KVM: x86: update %rip after emulating IO")
Reported-by: Simon Becherer <simon@becherer.de>
Reported-and-tested-by: Iakov Karpov <srid@rkmail.ru>
Reported-by: Gabriele Balducci <balducci@units.it>
Reported-by: Antti Antinoja <reader@fennosys.fi>
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/include/uapi/asm/kvm.h |    1 +
 arch/x86/kvm/x86.c              |   21 +++++++++++++++++++--
 2 files changed, 20 insertions(+), 2 deletions(-)

--- a/arch/x86/include/uapi/asm/kvm.h
+++ b/arch/x86/include/uapi/asm/kvm.h
@@ -381,6 +381,7 @@ struct kvm_sync_regs {
 #define KVM_X86_QUIRK_LINT0_REENABLED	(1 << 0)
 #define KVM_X86_QUIRK_CD_NW_CLEARED	(1 << 1)
 #define KVM_X86_QUIRK_LAPIC_MMIO_HOLE	(1 << 2)
+#define KVM_X86_QUIRK_OUT_7E_INC_RIP	(1 << 3)
 
 #define KVM_STATE_NESTED_GUEST_MODE	0x00000001
 #define KVM_STATE_NESTED_RUN_PENDING	0x00000002
--- a/arch/x86/kvm/x86.c
+++ b/arch/x86/kvm/x86.c
@@ -6536,6 +6536,12 @@ int kvm_emulate_instruction_from_buffer(
 }
 EXPORT_SYMBOL_GPL(kvm_emulate_instruction_from_buffer);
 
+static int complete_fast_pio_out_port_0x7e(struct kvm_vcpu *vcpu)
+{
+	vcpu->arch.pio.count = 0;
+	return 1;
+}
+
 static int complete_fast_pio_out(struct kvm_vcpu *vcpu)
 {
 	vcpu->arch.pio.count = 0;
@@ -6552,12 +6558,23 @@ static int kvm_fast_pio_out(struct kvm_v
 	unsigned long val = kvm_register_read(vcpu, VCPU_REGS_RAX);
 	int ret = emulator_pio_out_emulated(&vcpu->arch.emulate_ctxt,
 					    size, port, &val, 1);
+	if (ret)
+		return ret;
 
-	if (!ret) {
+	/*
+	 * Workaround userspace that relies on old KVM behavior of %rip being
+	 * incremented prior to exiting to userspace to handle "OUT 0x7e".
+	 */
+	if (port == 0x7e &&
+	    kvm_check_has_quirk(vcpu->kvm, KVM_X86_QUIRK_OUT_7E_INC_RIP)) {
+		vcpu->arch.complete_userspace_io =
+			complete_fast_pio_out_port_0x7e;
+		kvm_skip_emulated_instruction(vcpu);
+	} else {
 		vcpu->arch.pio.linear_rip = kvm_get_linear_rip(vcpu);
 		vcpu->arch.complete_userspace_io = complete_fast_pio_out;
 	}
-	return ret;
+	return 0;
 }
 
 static int complete_fast_pio_in(struct kvm_vcpu *vcpu)

[PATCH 5.0 29/32] KVM: nVMX: Fix size checks in vmx_set_nested_state

[Greg Kroah-Hartman]

From: Jim Mattson <jmattson@google.com>

commit e8ab8d24b488632d07ce5ddb261f1d454114415b upstream.

The size checks in vmx_nested_state are wrong because the calculations
are made based on the size of a pointer to a struct kvm_nested_state
rather than the size of a struct kvm_nested_state.

Reported-by: Felix Wilhelm  <fwilhelm@google.com>
Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Drew Schmitt <dasch@google.com>
Reviewed-by: Marc Orr <marcorr@google.com>
Reviewed-by: Peter Shier <pshier@google.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Fixes: 8fcc4b5923af5de58b80b53a069453b135693304
Cc: stable@ver.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 arch/x86/kvm/vmx/nested.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/arch/x86/kvm/vmx/nested.c
+++ b/arch/x86/kvm/vmx/nested.c
@@ -5407,7 +5407,7 @@ static int vmx_set_nested_state(struct k
 		return ret;
 
 	/* Empty 'VMXON' state is permitted */
-	if (kvm_state->size < sizeof(kvm_state) + sizeof(*vmcs12))
+	if (kvm_state->size < sizeof(*kvm_state) + sizeof(*vmcs12))
 		return 0;
 
 	if (kvm_state->vmx.vmcs_pa != -1ull) {
@@ -5451,7 +5451,7 @@ static int vmx_set_nested_state(struct k
 	    vmcs12->vmcs_link_pointer != -1ull) {
 		struct vmcs12 *shadow_vmcs12 = get_shadow_vmcs12(vcpu);
 
-		if (kvm_state->size < sizeof(kvm_state) + 2 * sizeof(*vmcs12))
+		if (kvm_state->size < sizeof(*kvm_state) + 2 * sizeof(*vmcs12))
 			return -EINVAL;
 
 		if (copy_from_user(shadow_vmcs12,

[PATCH 5.0 30/32] ALSA: line6: use dynamic buffers

[Greg Kroah-Hartman]

From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e5c812e84f0dece3400d5caf42522287e6ef139f upstream.

The line6 driver uses a lot of USB buffers off of the stack, which is
not allowed on many systems, causing the driver to crash on some of
them.  Fix this up by dynamically allocating the buffers with kmalloc()
which allows for proper DMA-able memory.

Reported-by: Christo Gouws <gouws.christo@gmail.com>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Christo Gouws <gouws.christo@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 sound/usb/line6/driver.c   |   60 ++++++++++++++++++++++++++-------------------
 sound/usb/line6/podhd.c    |   21 +++++++++------
 sound/usb/line6/toneport.c |   24 +++++++++++++-----
 3 files changed, 65 insertions(+), 40 deletions(-)

--- a/sound/usb/line6/driver.c
+++ b/sound/usb/line6/driver.c
@@ -351,12 +351,16 @@ int line6_read_data(struct usb_line6 *li
 {
 	struct usb_device *usbdev = line6->usbdev;
 	int ret;
-	unsigned char len;
+	unsigned char *len;
 	unsigned count;
 
 	if (address > 0xffff || datalen > 0xff)
 		return -EINVAL;
 
+	len = kmalloc(sizeof(*len), GFP_KERNEL);
+	if (!len)
+		return -ENOMEM;
+
 	/* query the serial number: */
 	ret = usb_control_msg(usbdev, usb_sndctrlpipe(usbdev, 0), 0x67,
 			      USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
@@ -365,7 +369,7 @@ int line6_read_data(struct usb_line6 *li
 
 	if (ret < 0) {
 		dev_err(line6->ifcdev, "read request failed (error %d)\n", ret);
-		return ret;
+		goto exit;
 	}
 
 	/* Wait for data length. We'll get 0xff until length arrives. */
@@ -375,28 +379,29 @@ int line6_read_data(struct usb_line6 *li
 		ret = usb_control_msg(usbdev, usb_rcvctrlpipe(usbdev, 0), 0x67,
 				      USB_TYPE_VENDOR | USB_RECIP_DEVICE |
 				      USB_DIR_IN,
-				      0x0012, 0x0000, &len, 1,
+				      0x0012, 0x0000, len, 1,
 				      LINE6_TIMEOUT * HZ);
 		if (ret < 0) {
 			dev_err(line6->ifcdev,
 				"receive length failed (error %d)\n", ret);
-			return ret;
+			goto exit;
 		}
 
-		if (len != 0xff)
+		if (*len != 0xff)
 			break;
 	}
 
-	if (len == 0xff) {
+	ret = -EIO;
+	if (*len == 0xff) {
 		dev_err(line6->ifcdev, "read failed after %d retries\n",
 			count);
-		return -EIO;
-	} else if (len != datalen) {
+		goto exit;
+	} else if (*len != datalen) {
 		/* should be equal or something went wrong */
 		dev_err(line6->ifcdev,
 			"length mismatch (expected %d, got %d)\n",
-			(int)datalen, (int)len);
-		return -EIO;
+			(int)datalen, (int)*len);
+		goto exit;
 	}
 
 	/* receive the result: */
@@ -405,12 +410,12 @@ int line6_read_data(struct usb_line6 *li
 			      0x0013, 0x0000, data, datalen,
 			      LINE6_TIMEOUT * HZ);
 
-	if (ret < 0) {
+	if (ret < 0)
 		dev_err(line6->ifcdev, "read failed (error %d)\n", ret);
-		return ret;
-	}
 
-	return 0;
+exit:
+	kfree(len);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(line6_read_data);
 
@@ -422,12 +427,16 @@ int line6_write_data(struct usb_line6 *l
 {
 	struct usb_device *usbdev = line6->usbdev;
 	int ret;
-	unsigned char status;
+	unsigned char *status;
 	int count;
 
 	if (address > 0xffff || datalen > 0xffff)
 		return -EINVAL;
 
+	status = kmalloc(sizeof(*status), GFP_KERNEL);
+	if (!status)
+		return -ENOMEM;
+
 	ret = usb_control_msg(usbdev, usb_sndctrlpipe(usbdev, 0), 0x67,
 			      USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
 			      0x0022, address, data, datalen,
@@ -436,7 +445,7 @@ int line6_write_data(struct usb_line6 *l
 	if (ret < 0) {
 		dev_err(line6->ifcdev,
 			"write request failed (error %d)\n", ret);
-		return ret;
+		goto exit;
 	}
 
 	for (count = 0; count < LINE6_READ_WRITE_MAX_RETRIES; count++) {
@@ -447,28 +456,29 @@ int line6_write_data(struct usb_line6 *l
 				      USB_TYPE_VENDOR | USB_RECIP_DEVICE |
 				      USB_DIR_IN,
 				      0x0012, 0x0000,
-				      &status, 1, LINE6_TIMEOUT * HZ);
+				      status, 1, LINE6_TIMEOUT * HZ);
 
 		if (ret < 0) {
 			dev_err(line6->ifcdev,
 				"receiving status failed (error %d)\n", ret);
-			return ret;
+			goto exit;
 		}
 
-		if (status != 0xff)
+		if (*status != 0xff)
 			break;
 	}
 
-	if (status == 0xff) {
+	if (*status == 0xff) {
 		dev_err(line6->ifcdev, "write failed after %d retries\n",
 			count);
-		return -EIO;
-	} else if (status != 0) {
+		ret = -EIO;
+	} else if (*status != 0) {
 		dev_err(line6->ifcdev, "write failed (error %d)\n", ret);
-		return -EIO;
+		ret = -EIO;
 	}
-
-	return 0;
+exit:
+	kfree(status);
+	return ret;
 }
 EXPORT_SYMBOL_GPL(line6_write_data);
 
--- a/sound/usb/line6/podhd.c
+++ b/sound/usb/line6/podhd.c
@@ -225,28 +225,32 @@ static void podhd_startup_start_workqueu
 static int podhd_dev_start(struct usb_line6_podhd *pod)
 {
 	int ret;
-	u8 init_bytes[8];
+	u8 *init_bytes;
 	int i;
 	struct usb_device *usbdev = pod->line6.usbdev;
 
+	init_bytes = kmalloc(8, GFP_KERNEL);
+	if (!init_bytes)
+		return -ENOMEM;
+
 	ret = usb_control_msg(usbdev, usb_sndctrlpipe(usbdev, 0),
 					0x67, USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT,
 					0x11, 0,
 					NULL, 0, LINE6_TIMEOUT * HZ);
 	if (ret < 0) {
 		dev_err(pod->line6.ifcdev, "read request failed (error %d)\n", ret);
-		return ret;
+		goto exit;
 	}
 
 	/* NOTE: looks like some kind of ping message */
 	ret = usb_control_msg(usbdev, usb_rcvctrlpipe(usbdev, 0), 0x67,
 					USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_IN,
 					0x11, 0x0,
-					&init_bytes, 3, LINE6_TIMEOUT * HZ);
+					init_bytes, 3, LINE6_TIMEOUT * HZ);
 	if (ret < 0) {
 		dev_err(pod->line6.ifcdev,
 			"receive length failed (error %d)\n", ret);
-		return ret;
+		goto exit;
 	}
 
 	pod->firmware_version =
@@ -255,7 +259,7 @@ static int podhd_dev_start(struct usb_li
 	for (i = 0; i <= 16; i++) {
 		ret = line6_read_data(&pod->line6, 0xf000 + 0x08 * i, init_bytes, 8);
 		if (ret < 0)
-			return ret;
+			goto exit;
 	}
 
 	ret = usb_control_msg(usbdev, usb_sndctrlpipe(usbdev, 0),
@@ -263,10 +267,9 @@ static int podhd_dev_start(struct usb_li
 					USB_TYPE_STANDARD | USB_RECIP_DEVICE | USB_DIR_OUT,
 					1, 0,
 					NULL, 0, LINE6_TIMEOUT * HZ);
-	if (ret < 0)
-		return ret;
-
-	return 0;
+exit:
+	kfree(init_bytes);
+	return ret;
 }
 
 static void podhd_startup_workqueue(struct work_struct *work)
--- a/sound/usb/line6/toneport.c
+++ b/sound/usb/line6/toneport.c
@@ -365,16 +365,21 @@ static bool toneport_has_source_select(s
 /*
 	Setup Toneport device.
 */
-static void toneport_setup(struct usb_line6_toneport *toneport)
+static int toneport_setup(struct usb_line6_toneport *toneport)
 {
-	u32 ticks;
+	u32 *ticks;
 	struct usb_line6 *line6 = &toneport->line6;
 	struct usb_device *usbdev = line6->usbdev;
 
+	ticks = kmalloc(sizeof(*ticks), GFP_KERNEL);
+	if (!ticks)
+		return -ENOMEM;
+
 	/* sync time on device with host: */
 	/* note: 32-bit timestamps overflow in year 2106 */
-	ticks = (u32)ktime_get_real_seconds();
-	line6_write_data(line6, 0x80c6, &ticks, 4);
+	*ticks = (u32)ktime_get_real_seconds();
+	line6_write_data(line6, 0x80c6, ticks, 4);
+	kfree(ticks);
 
 	/* enable device: */
 	toneport_send_cmd(usbdev, 0x0301, 0x0000);
@@ -389,6 +394,7 @@ static void toneport_setup(struct usb_li
 		toneport_update_led(toneport);
 
 	mod_timer(&toneport->timer, jiffies + TONEPORT_PCM_DELAY * HZ);
+	return 0;
 }
 
 /*
@@ -451,7 +457,9 @@ static int toneport_init(struct usb_line
 			return err;
 	}
 
-	toneport_setup(toneport);
+	err = toneport_setup(toneport);
+	if (err)
+		return err;
 
 	/* register audio system: */
 	return snd_card_register(line6->card);
@@ -463,7 +471,11 @@ static int toneport_init(struct usb_line
 */
 static int toneport_reset_resume(struct usb_interface *interface)
 {
-	toneport_setup(usb_get_intfdata(interface));
+	int err;
+
+	err = toneport_setup(usb_get_intfdata(interface));
+	if (err)
+		return err;
 	return line6_resume(interface);
 }
 #endif

[PATCH 5.0 31/32] iwlwifi: mvm: properly check debugfs dentry before using it

[Greg Kroah-Hartman]

From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 154d4899e4111ae24e68d6ba955f46856cb046bc upstream.

debugfs can now report an error code if something went wrong instead of
just NULL.  So if the return value is to be used as a "real" dentry, it
needs to be checked if it is an error before dereferencing it.

This is now happening because of ff9fb72bc077 ("debugfs: return error
values, not NULL").  If multiple iwlwifi devices are in the system, this
can cause problems when the driver attempts to create the main debugfs
directory again.  Later on in the code we fail horribly by trying to
dereference a pointer that is an error value.

Reported-by: Laura Abbott <labbott@redhat.com>
Reported-by: Gabriel Ramirez <gabriello.ramirez@gmail.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: stable <stable@vger.kernel.org> # 5.0
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/wireless/intel/iwlwifi/mvm/debugfs-vif.c |    5 +++++
 1 file changed, 5 insertions(+)

--- a/drivers/net/wireless/intel/iwlwifi/mvm/debugfs-vif.c
+++ b/drivers/net/wireless/intel/iwlwifi/mvm/debugfs-vif.c
@@ -1482,6 +1482,11 @@ void iwl_mvm_vif_dbgfs_register(struct i
 		return;
 
 	mvmvif->dbgfs_dir = debugfs_create_dir("iwlmvm", dbgfs_dir);
+	if (IS_ERR_OR_NULL(mvmvif->dbgfs_dir)) {
+		IWL_ERR(mvm, "Failed to create debugfs directory under %pd\n",
+			dbgfs_dir);
+		return;
+	}
 
 	if (!mvmvif->dbgfs_dir) {
 		IWL_ERR(mvm, "Failed to create debugfs directory under %pd\n",

[PATCH 5.0 32/32] ath10k: Drop WARN_ON()s that always trigger during system resume

[Greg Kroah-Hartman]

From: Rafael J. Wysocki <rafael.j.wysocki@intel.com>

commit 9e80ad37f6788ed52b89a3cfcd593e0aa69b216d upstream.

ath10k_mac_vif_chan() always returns an error for the given vif
during system-wide resume which reliably triggers two WARN_ON()s
in ath10k_bss_info_changed() and they are not particularly
useful in that code path, so drop them.

Tested: QCA6174 hw3.2 PCI with WLAN.RM.2.0-00180-QCARMSWPZ-1
Tested: QCA6174 hw3.2 SDIO with WLAN.RMH.4.4.1-00007-QCARMSWP-1

Fixes: cd93b83ad927 ("ath10k: support for multicast rate control")
Fixes: f279294e9ee2 ("ath10k: add support for configuring management packet rate")
Cc: stable@vger.kernel.org
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

---
 drivers/net/wireless/ath/ath10k/mac.c |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

--- a/drivers/net/wireless/ath/ath10k/mac.c
+++ b/drivers/net/wireless/ath/ath10k/mac.c
@@ -5705,7 +5705,7 @@ static void ath10k_bss_info_changed(stru
 	}
 
 	if (changed & BSS_CHANGED_MCAST_RATE &&
-	    !WARN_ON(ath10k_mac_vif_chan(arvif->vif, &def))) {
+	    !ath10k_mac_vif_chan(arvif->vif, &def)) {
 		band = def.chan->band;
 		rateidx = vif->bss_conf.mcast_rate[band] - 1;
 
@@ -5743,7 +5743,7 @@ static void ath10k_bss_info_changed(stru
 	}
 
 	if (changed & BSS_CHANGED_BASIC_RATES) {
-		if (WARN_ON(ath10k_mac_vif_chan(vif, &def))) {
+		if (ath10k_mac_vif_chan(vif, &def)) {
 			mutex_unlock(&ar->conf_mutex);
 			return;
 		}

Re: [PATCH 5.0 00/32] 5.0.13-stable review

[kernelci.org bot]

stable-rc/linux-5.0.y boot: 136 boots: 0 failed, 130 passed with 4 offline, 2 untried/unknown (v5.0.12-33-gc6bd3efdcefd)

Full Boot Summary: https://kernelci.org/boot/all/job/stable-rc/branch/linux-5.0.y/kernel/v5.0.12-33-gc6bd3efdcefd/
Full Build Summary: https://kernelci.org/build/stable-rc/branch/linux-5.0.y/kernel/v5.0.12-33-gc6bd3efdcefd/

Tree: stable-rc
Branch: linux-5.0.y
Git Describe: v5.0.12-33-gc6bd3efdcefd
Git Commit: c6bd3efdcefd68cc590853c50594a9fc971d93cd
Git URL: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
Tested: 76 unique boards, 24 SoC families, 14 builds out of 207

Offline Platforms:

arm:

    davinci_all_defconfig:
        gcc-7
            dm365evm,legacy: 1 offline lab

    exynos_defconfig:
        gcc-7
            exynos5800-peach-pi: 1 offline lab

    multi_v7_defconfig:
        gcc-7
            exynos5800-peach-pi: 1 offline lab
            stih410-b2120: 1 offline lab

---
For more info write to <info@kernelci.org>

Re: [PATCH 5.0 00/32] 5.0.13-stable review

[Guenter Roeck]

On 5/4/19 3:24 AM, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 5.0.13 release.
> There are 32 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Mon 06 May 2019 10:24:23 AM UTC.
> Anything received after that time might be too late.
> 

Build results:
	total: 159 pass: 159 fail: 0
Qemu test results:
	total: 349 pass: 349 fail: 0

Guenter

Re: [PATCH 5.0 00/32] 5.0.13-stable review

[Greg Kroah-Hartman]

On Sat, May 04, 2019 at 04:53:10PM -0700, Guenter Roeck wrote:
> On 5/4/19 3:24 AM, Greg Kroah-Hartman wrote:
> > This is the start of the stable review cycle for the 5.0.13 release.
> > There are 32 patches in this series, all will be posted as a response
> > to this one.  If anyone has any issues with these being applied, please
> > let me know.
> > 
> > Responses should be made by Mon 06 May 2019 10:24:23 AM UTC.
> > Anything received after that time might be too late.
> > 
> 
> Build results:
> 	total: 159 pass: 159 fail: 0
> Qemu test results:
> 	total: 349 pass: 349 fail: 0

Thanks for testing both of these and letting me know.

greg k-h

Re: [PATCH 5.0 00/32] 5.0.13-stable review

[Dan Rue]

On Sat, May 04, 2019 at 12:24:45PM +0200, Greg Kroah-Hartman wrote:
> This is the start of the stable review cycle for the 5.0.13 release.
> There are 32 patches in this series, all will be posted as a response
> to this one.  If anyone has any issues with these being applied, please
> let me know.
> 
> Responses should be made by Mon 06 May 2019 10:24:23 AM UTC.
> Anything received after that time might be too late.

Results from Linaro’s test farm.
Regressions detected.

Summary
------------------------------------------------------------------------

kernel: 5.0.13-rc1
git repo: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
git branch: linux-5.0.y
git commit: c6bd3efdcefd68cc590853c50594a9fc971d93cd
git describe: v5.0.12-33-gc6bd3efdcefd
Test details: https://qa-reports.linaro.org/lkft/linux-stable-rc-5.0-oe/build/v5.0.12-33-gc6bd3efdcefd

No regressions (compared to build v5.0.11-102-g17f93022a8c9)

No fixes (compared to build v5.0.11-102-g17f93022a8c9)

Ran 25060 total tests in the following environments and test suites.

Environments
--------------
- dragonboard-410c
- hi6220-hikey
- i386
- juno-r2
- qemu_arm
- qemu_arm64
- qemu_i386
- qemu_x86_64
- x15
- x86

Test Suites
-----------
* build
* install-android-platform-tools-r2600
* kselftest
* libgpiod
* libhugetlbfs
* ltp-cap_bounds-tests
* ltp-commands-tests
* ltp-containers-tests
* ltp-cpuhotplug-tests
* ltp-cve-tests
* ltp-dio-tests
* ltp-fcntl-locktests-tests
* ltp-filecaps-tests
* ltp-fs_bind-tests
* ltp-fs_perms_simple-tests
* ltp-fsx-tests
* ltp-hugetlb-tests
* ltp-io-tests
* ltp-ipc-tests
* ltp-math-tests
* ltp-mm-tests
* ltp-nptl-tests
* ltp-pty-tests
* ltp-sched-tests
* ltp-securebits-tests
* ltp-syscalls-tests
* ltp-timers-tests
* perf
* spectre-meltdown-checker-test
* v4l2-compliance
* kvm-unit-tests
* ltp-fs-tests
* ltp-open-posix-tests
* kselftest-vsyscall-mode-native
* kselftest-vsyscall-mode-none

-- 
Linaro LKFT
https://lkft.linaro.org

Re: [PATCH 5.0 00/32] 5.0.13-stable review

[Guenter Roeck]

On 5/4/19 8:05 PM, Dan Rue wrote:
> On Sat, May 04, 2019 at 12:24:45PM +0200, Greg Kroah-Hartman wrote:
>> This is the start of the stable review cycle for the 5.0.13 release.
>> There are 32 patches in this series, all will be posted as a response
>> to this one.  If anyone has any issues with these being applied, please
>> let me know.
>>
>> Responses should be made by Mon 06 May 2019 10:24:23 AM UTC.
>> Anything received after that time might be too late.
> 
> Results from Linaro’s test farm.
> Regressions detected.
> 

Confusing. What are the regressions ? Below it says that there are none.

Guenter

> Summary
> ------------------------------------------------------------------------
> 
> kernel: 5.0.13-rc1
> git repo: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
> git branch: linux-5.0.y
> git commit: c6bd3efdcefd68cc590853c50594a9fc971d93cd
> git describe: v5.0.12-33-gc6bd3efdcefd
> Test details: https://qa-reports.linaro.org/lkft/linux-stable-rc-5.0-oe/build/v5.0.12-33-gc6bd3efdcefd
> 
> No regressions (compared to build v5.0.11-102-g17f93022a8c9)
> 
> No fixes (compared to build v5.0.11-102-g17f93022a8c9)
> 
> Ran 25060 total tests in the following environments and test suites.
> 
> Environments
> --------------
> - dragonboard-410c
> - hi6220-hikey
> - i386
> - juno-r2
> - qemu_arm
> - qemu_arm64
> - qemu_i386
> - qemu_x86_64
> - x15
> - x86
> 
> Test Suites
> -----------
> * build
> * install-android-platform-tools-r2600
> * kselftest
> * libgpiod
> * libhugetlbfs
> * ltp-cap_bounds-tests
> * ltp-commands-tests
> * ltp-containers-tests
> * ltp-cpuhotplug-tests
> * ltp-cve-tests
> * ltp-dio-tests
> * ltp-fcntl-locktests-tests
> * ltp-filecaps-tests
> * ltp-fs_bind-tests
> * ltp-fs_perms_simple-tests
> * ltp-fsx-tests
> * ltp-hugetlb-tests
> * ltp-io-tests
> * ltp-ipc-tests
> * ltp-math-tests
> * ltp-mm-tests
> * ltp-nptl-tests
> * ltp-pty-tests
> * ltp-sched-tests
> * ltp-securebits-tests
> * ltp-syscalls-tests
> * ltp-timers-tests
> * perf
> * spectre-meltdown-checker-test
> * v4l2-compliance
> * kvm-unit-tests
> * ltp-fs-tests
> * ltp-open-posix-tests
> * kselftest-vsyscall-mode-native
> * kselftest-vsyscall-mode-none
> 

Re: [PATCH 5.0 00/32] 5.0.13-stable review

[Dan Rue]

On Sat, May 04, 2019 at 08:31:36PM -0700, Guenter Roeck wrote:
> On 5/4/19 8:05 PM, Dan Rue wrote:
> > On Sat, May 04, 2019 at 12:24:45PM +0200, Greg Kroah-Hartman wrote:
> > > This is the start of the stable review cycle for the 5.0.13 release.
> > > There are 32 patches in this series, all will be posted as a response
> > > to this one.  If anyone has any issues with these being applied, please
> > > let me know.
> > > 
> > > Responses should be made by Mon 06 May 2019 10:24:23 AM UTC.
> > > Anything received after that time might be too late.
> > 
> > Results from Linaro’s test farm.
> > Regressions detected.
> > 
> 
> Confusing. What are the regressions ? Below it says that there are none.

My mistake for dashing it off too quickly. No regressions on arm64, arm,
x86_64, and i386.

Dan

> 
> Guenter
> 
> > Summary
> > ------------------------------------------------------------------------
> > 
> > kernel: 5.0.13-rc1
> > git repo: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux-stable-rc.git
> > git branch: linux-5.0.y
> > git commit: c6bd3efdcefd68cc590853c50594a9fc971d93cd
> > git describe: v5.0.12-33-gc6bd3efdcefd
> > Test details: https://qa-reports.linaro.org/lkft/linux-stable-rc-5.0-oe/build/v5.0.12-33-gc6bd3efdcefd
> > 
> > No regressions (compared to build v5.0.11-102-g17f93022a8c9)
> > 
> > No fixes (compared to build v5.0.11-102-g17f93022a8c9)
> > 
> > Ran 25060 total tests in the following environments and test suites.
> > 
> > Environments
> > --------------
> > - dragonboard-410c
> > - hi6220-hikey
> > - i386
> > - juno-r2
> > - qemu_arm
> > - qemu_arm64
> > - qemu_i386
> > - qemu_x86_64
> > - x15
> > - x86
> > 
> > Test Suites
> > -----------
> > * build
> > * install-android-platform-tools-r2600
> > * kselftest
> > * libgpiod
> > * libhugetlbfs
> > * ltp-cap_bounds-tests
> > * ltp-commands-tests
> > * ltp-containers-tests
> > * ltp-cpuhotplug-tests
> > * ltp-cve-tests
> > * ltp-dio-tests
> > * ltp-fcntl-locktests-tests
> > * ltp-filecaps-tests
> > * ltp-fs_bind-tests
> > * ltp-fs_perms_simple-tests
> > * ltp-fsx-tests
> > * ltp-hugetlb-tests
> > * ltp-io-tests
> > * ltp-ipc-tests
> > * ltp-math-tests
> > * ltp-mm-tests
> > * ltp-nptl-tests
> > * ltp-pty-tests
> > * ltp-sched-tests
> > * ltp-securebits-tests
> > * ltp-syscalls-tests
> > * ltp-timers-tests
> > * perf
> > * spectre-meltdown-checker-test
> > * v4l2-compliance
> > * kvm-unit-tests
> > * ltp-fs-tests
> > * ltp-open-posix-tests
> > * kselftest-vsyscall-mode-native
> > * kselftest-vsyscall-mode-none
> > 
> 

-- 
Linaro - Kernel Validation

Re: [PATCH 5.0 00/32] 5.0.13-stable review

[Greg Kroah-Hartman]

On Sun, May 05, 2019 at 07:17:48AM -0500, Dan Rue wrote:
> On Sat, May 04, 2019 at 08:31:36PM -0700, Guenter Roeck wrote:
> > On 5/4/19 8:05 PM, Dan Rue wrote:
> > > On Sat, May 04, 2019 at 12:24:45PM +0200, Greg Kroah-Hartman wrote:
> > > > This is the start of the stable review cycle for the 5.0.13 release.
> > > > There are 32 patches in this series, all will be posted as a response
> > > > to this one.  If anyone has any issues with these being applied, please
> > > > let me know.
> > > > 
> > > > Responses should be made by Mon 06 May 2019 10:24:23 AM UTC.
> > > > Anything received after that time might be too late.
> > > 
> > > Results from Linaro’s test farm.
> > > Regressions detected.
> > > 
> > 
> > Confusing. What are the regressions ? Below it says that there are none.
> 
> My mistake for dashing it off too quickly. No regressions on arm64, arm,
> x86_64, and i386.

Thanks for confirming this.

greg k-h