[PATCH 4.14 30/59] x86/apic: Fix arch_dynirq_lower_bound() bug for DT enabled machines

[Greg Kroah-Hartman <gregkh@linuxfoundation.org>]

From: Thomas Gleixner <tglx@linutronix.de>

[ Upstream commit 3e5bedc2c258341702ddffbd7688c5e6eb01eafa ]

Rahul Tanwar reported the following bug on DT systems:

> 'ioapic_dynirq_base' contains the virtual IRQ base number. Presently, it is
> updated to the end of hardware IRQ numbers but this is done only when IOAPIC
> configuration type is IOAPIC_DOMAIN_LEGACY or IOAPIC_DOMAIN_STRICT. There is
> a third type IOAPIC_DOMAIN_DYNAMIC which applies when IOAPIC configuration
> comes from devicetree.
>
> See dtb_add_ioapic() in arch/x86/kernel/devicetree.c
>
> In case of IOAPIC_DOMAIN_DYNAMIC (DT/OF based system), 'ioapic_dynirq_base'
> remains to zero initialized value. This means that for OF based systems,
> virtual IRQ base will get set to zero.

Such systems will very likely not even boot.

For DT enabled machines ioapic_dynirq_base is irrelevant and not
updated, so simply map the IRQ base 1:1 instead.

Reported-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Tested-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: alan@linux.intel.com
Cc: bp@alien8.de
Cc: cheol.yong.kim@intel.com
Cc: qi-ming.wu@intel.com
Cc: rahul.tanwar@intel.com
Cc: rppt@linux.ibm.com
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/20190821081330.1187-1-rahul.tanwar@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/x86/kernel/apic/io_apic.c | 8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

diff --git a/arch/x86/kernel/apic/io_apic.c b/arch/x86/kernel/apic/io_apic.c
index 96a8a68f9c793..566b7bc5deaa0 100644
--- a/arch/x86/kernel/apic/io_apic.c
+++ b/arch/x86/kernel/apic/io_apic.c
@@ -2342,7 +2342,13 @@ unsigned int arch_dynirq_lower_bound(unsigned int from)
 	 * dmar_alloc_hwirq() may be called before setup_IO_APIC(), so use
 	 * gsi_top if ioapic_dynirq_base hasn't been initialized yet.
 	 */
-	return ioapic_initialized ? ioapic_dynirq_base : gsi_top;
+	if (!ioapic_initialized)
+		return gsi_top;
+	/*
+	 * For DT enabled machines ioapic_dynirq_base is irrelevant and not
+	 * updated. So simply return @from if ioapic_dynirq_base == 0.
+	 */
+	return ioapic_dynirq_base ? : from;
 }
 
 #ifdef CONFIG_X86_32
-- 
2.20.1