[PATCH AUTOSEL 4.19 01/32] ALSA: hda: do not override bus codec_mask in link_get()

[PATCH AUTOSEL 4.19 01/32] ALSA: hda: do not override bus codec_mask in link_get()

[Sasha Levin]

From: Kai Vehmanen <kai.vehmanen@linux.intel.com>

[ Upstream commit 43bcb1c0507858cdc95e425017dcc33f8105df39 ]

snd_hdac_ext_bus_link_get() does not work correctly in case
there are multiple codecs on the bus. It unconditionally
resets the bus->codec_mask value. As per documentation in
hdaudio.h and existing use in client code, this field should
be used to store bit flag of detected codecs on the bus.

By overwriting value of the codec_mask, information on all
detected codecs is lost. No current user of hdac is impacted,
but use of bus->codec_mask is planned in future patches
for SOF.

Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20200206200223.7715-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 sound/hda/ext/hdac_ext_controller.c | 9 ++++++---
 1 file changed, 6 insertions(+), 3 deletions(-)

diff --git a/sound/hda/ext/hdac_ext_controller.c b/sound/hda/ext/hdac_ext_controller.c
index 60cb00fd0c693..84b44cdae28a1 100644
--- a/sound/hda/ext/hdac_ext_controller.c
+++ b/sound/hda/ext/hdac_ext_controller.c
@@ -262,6 +262,7 @@ EXPORT_SYMBOL_GPL(snd_hdac_ext_bus_link_power_down_all);
 int snd_hdac_ext_bus_link_get(struct hdac_bus *bus,
 				struct hdac_ext_link *link)
 {
+	unsigned long codec_mask;
 	int ret = 0;
 
 	mutex_lock(&bus->lock);
@@ -283,9 +284,11 @@ int snd_hdac_ext_bus_link_get(struct hdac_bus *bus,
 		 *  HDA spec section 4.3 - Codec Discovery
 		 */
 		udelay(521);
-		bus->codec_mask = snd_hdac_chip_readw(bus, STATESTS);
-		dev_dbg(bus->dev, "codec_mask = 0x%lx\n", bus->codec_mask);
-		snd_hdac_chip_writew(bus, STATESTS, bus->codec_mask);
+		codec_mask = snd_hdac_chip_readw(bus, STATESTS);
+		dev_dbg(bus->dev, "codec_mask = 0x%lx\n", codec_mask);
+		snd_hdac_chip_writew(bus, STATESTS, codec_mask);
+		if (!bus->codec_mask)
+			bus->codec_mask = codec_mask;
 	}
 
 	mutex_unlock(&bus->lock);
-- 
2.20.1

[PATCH AUTOSEL 4.19 02/32] usb: charger: assign specific number for enum value

[Sasha Levin]

From: Peter Chen <peter.chen@nxp.com>

[ Upstream commit ca4b43c14cd88d28cfc6467d2fa075aad6818f1d ]

To work properly on every architectures and compilers, the enum value
needs to be specific numbers.

Suggested-by: Greg KH <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/1580537624-10179-1-git-send-email-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 include/uapi/linux/usb/charger.h | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/include/uapi/linux/usb/charger.h b/include/uapi/linux/usb/charger.h
index 5f72af35b3ed7..ad22079125bff 100644
--- a/include/uapi/linux/usb/charger.h
+++ b/include/uapi/linux/usb/charger.h
@@ -14,18 +14,18 @@
  * ACA (Accessory Charger Adapters)
  */
 enum usb_charger_type {
-	UNKNOWN_TYPE,
-	SDP_TYPE,
-	DCP_TYPE,
-	CDP_TYPE,
-	ACA_TYPE,
+	UNKNOWN_TYPE = 0,
+	SDP_TYPE = 1,
+	DCP_TYPE = 2,
+	CDP_TYPE = 3,
+	ACA_TYPE = 4,
 };
 
 /* USB charger state */
 enum usb_charger_state {
-	USB_CHARGER_DEFAULT,
-	USB_CHARGER_PRESENT,
-	USB_CHARGER_ABSENT,
+	USB_CHARGER_DEFAULT = 0,
+	USB_CHARGER_PRESENT = 1,
+	USB_CHARGER_ABSENT = 2,
 };
 
 #endif /* _UAPI__LINUX_USB_CHARGER_H */
-- 
2.20.1

[PATCH AUTOSEL 4.19 03/32] serial: ar933x_uart: set UART_CS_{RX,TX}_READY_ORIDE

[Sasha Levin]

From: Daniel Golle <daniel@makrotopia.org>

[ Upstream commit 87c5cbf71ecbb9e289d60a2df22eb686c70bf196 ]

On AR934x this UART is usually not initialized by the bootloader
as it is only used as a secondary serial port while the primary
UART is a newly introduced NS16550-compatible.
In order to make use of the ar933x-uart on AR934x without RTS/CTS
hardware flow control, one needs to set the
UART_CS_{RX,TX}_READY_ORIDE bits as other than on AR933x where this
UART is used as primary/console, the bootloader on AR934x typically
doesn't set those bits.
Setting them explicitely on AR933x should not do any harm, so just
set them unconditionally.

Tested-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20200207095335.GA179836@makrotopia.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/ar933x_uart.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/tty/serial/ar933x_uart.c b/drivers/tty/serial/ar933x_uart.c
index 3bdd56a1021b2..ea12f10610b64 100644
--- a/drivers/tty/serial/ar933x_uart.c
+++ b/drivers/tty/serial/ar933x_uart.c
@@ -286,6 +286,10 @@ static void ar933x_uart_set_termios(struct uart_port *port,
 	ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
 			    AR933X_UART_CS_HOST_INT_EN);
 
+	/* enable RX and TX ready overide */
+	ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
+		AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
+
 	/* reenable the UART */
 	ar933x_uart_rmw(up, AR933X_UART_CS_REG,
 			AR933X_UART_CS_IF_MODE_M << AR933X_UART_CS_IF_MODE_S,
@@ -418,6 +422,10 @@ static int ar933x_uart_startup(struct uart_port *port)
 	ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
 			    AR933X_UART_CS_HOST_INT_EN);
 
+	/* enable RX and TX ready overide */
+	ar933x_uart_rmw_set(up, AR933X_UART_CS_REG,
+		AR933X_UART_CS_TX_READY_ORIDE | AR933X_UART_CS_RX_READY_ORIDE);
+
 	/* Enable RX interrupts */
 	up->ier = AR933X_UART_INT_RX_VALID;
 	ar933x_uart_write(up, AR933X_UART_INT_EN_REG, up->ier);
-- 
2.20.1

[PATCH AUTOSEL 4.19 04/32] selftests: fix too long argument

[Sasha Levin]

From: Jiri Benc <jbenc@redhat.com>

[ Upstream commit c363eb48ada5cf732b3f489fab799fc881097842 ]

With some shells, the command construed for install of bpf selftests becomes
too large due to long list of files:

make[1]: execvp: /bin/sh: Argument list too long
make[1]: *** [../lib.mk:73: install] Error 127

Currently, each of the file lists is replicated three times in the command:
in the shell 'if' condition, in the 'echo' and in the 'rsync'. Reduce that
by one instance by using make conditionals and separate the echo and rsync
into two shell commands. (One would be inclined to just remove the '@' at
the beginning of the rsync command and let 'make' echo it by itself;
unfortunately, it appears that the '@' in the front of mkdir silences output
also for the following commands.)

Also, separate handling of each of the lists to its own shell command.

The semantics of the makefile is unchanged before and after the patch. The
ability of individual test directories to override INSTALL_RULE is retained.

Reported-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Tested-by: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 tools/testing/selftests/lib.mk | 23 +++++++++++++----------
 1 file changed, 13 insertions(+), 10 deletions(-)

diff --git a/tools/testing/selftests/lib.mk b/tools/testing/selftests/lib.mk
index 8b0f16409ed7e..0ef203ec59fdc 100644
--- a/tools/testing/selftests/lib.mk
+++ b/tools/testing/selftests/lib.mk
@@ -85,17 +85,20 @@ else
 	$(call RUN_TESTS, $(TEST_GEN_PROGS) $(TEST_CUSTOM_PROGS) $(TEST_PROGS))
 endif
 
+define INSTALL_SINGLE_RULE
+	$(if $(INSTALL_LIST),@mkdir -p $(INSTALL_PATH))
+	$(if $(INSTALL_LIST),@echo rsync -a $(INSTALL_LIST) $(INSTALL_PATH)/)
+	$(if $(INSTALL_LIST),@rsync -a $(INSTALL_LIST) $(INSTALL_PATH)/)
+endef
+
 define INSTALL_RULE
-	@if [ "X$(TEST_PROGS)$(TEST_PROGS_EXTENDED)$(TEST_FILES)" != "X" ]; then					\
-		mkdir -p ${INSTALL_PATH};										\
-		echo "rsync -a $(TEST_PROGS) $(TEST_PROGS_EXTENDED) $(TEST_FILES) $(INSTALL_PATH)/";	\
-		rsync -a $(TEST_PROGS) $(TEST_PROGS_EXTENDED) $(TEST_FILES) $(INSTALL_PATH)/;		\
-	fi
-	@if [ "X$(TEST_GEN_PROGS)$(TEST_CUSTOM_PROGS)$(TEST_GEN_PROGS_EXTENDED)$(TEST_GEN_FILES)" != "X" ]; then					\
-		mkdir -p ${INSTALL_PATH};										\
-		echo "rsync -a $(TEST_GEN_PROGS) $(TEST_CUSTOM_PROGS) $(TEST_GEN_PROGS_EXTENDED) $(TEST_GEN_FILES) $(INSTALL_PATH)/";	\
-		rsync -a $(TEST_GEN_PROGS) $(TEST_CUSTOM_PROGS) $(TEST_GEN_PROGS_EXTENDED) $(TEST_GEN_FILES) $(INSTALL_PATH)/;		\
-	fi
+	$(eval INSTALL_LIST = $(TEST_PROGS)) $(INSTALL_SINGLE_RULE)
+	$(eval INSTALL_LIST = $(TEST_PROGS_EXTENDED)) $(INSTALL_SINGLE_RULE)
+	$(eval INSTALL_LIST = $(TEST_FILES)) $(INSTALL_SINGLE_RULE)
+	$(eval INSTALL_LIST = $(TEST_GEN_PROGS)) $(INSTALL_SINGLE_RULE)
+	$(eval INSTALL_LIST = $(TEST_CUSTOM_PROGS)) $(INSTALL_SINGLE_RULE)
+	$(eval INSTALL_LIST = $(TEST_GEN_PROGS_EXTENDED)) $(INSTALL_SINGLE_RULE)
+	$(eval INSTALL_LIST = $(TEST_GEN_FILES)) $(INSTALL_SINGLE_RULE)
 endef
 
 install: all
-- 
2.20.1

[PATCH AUTOSEL 4.19 05/32] usb: gadget: composite: Support more than 500mA MaxPower

[Sasha Levin]

From: Jack Pham <jackp@codeaurora.org>

[ Upstream commit a2035411fa1d1206cea7d5dfe833e78481844a76 ]

USB 3.x SuperSpeed peripherals can draw up to 900mA of VBUS power
when in configured state. However, if a configuration wanting to
take advantage of this is added with MaxPower greater than 500
(currently possible if using a ConfigFS gadget) the composite
driver fails to accommodate this for a couple reasons:

 - usb_gadget_vbus_draw() when called from set_config() and
   composite_resume() will be passed the MaxPower value without
   regard for the current connection speed, resulting in a
   violation for USB 2.0 since the max is 500mA.

 - the bMaxPower of the configuration descriptor would be
   incorrectly encoded, again if the connection speed is only
   at USB 2.0 or below, likely wrapping around U8_MAX since
   the 2mA multiplier corresponds to a maximum of 510mA.

Fix these by adding checks against the current gadget->speed
when the c->MaxPower value is used (set_config() and
composite_resume()) and appropriately limit based on whether
it is currently at a low-/full-/high- or super-speed connection.

Because 900 is not divisible by 8, with the round-up division
currently used in encode_bMaxPower() a MaxPower of 900mA will
result in an encoded value of 0x71. When a host stack (including
Linux and Windows) enumerates this on a single port root hub, it
reads this value back and decodes (multiplies by 8) to get 904mA
which is strictly greater than 900mA that is typically budgeted
for that port, causing it to reject the configuration. Instead,
we should be using the round-down behavior of normal integral
division so that 900 / 8 -> 0x70 or 896mA to stay within range.
And we might as well change it for the high/full/low case as well
for consistency.

N.B. USB 3.2 Gen N x 2 allows for up to 1500mA but there doesn't
seem to be any any peripheral controller supported by Linux that
does two lane operation, so for now keeping the clamp at 900
should be fine.

Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/gadget/composite.c | 24 ++++++++++++++++++------
 1 file changed, 18 insertions(+), 6 deletions(-)

diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c
index fea7c7e0143f2..30aefd1adbadd 100644
--- a/drivers/usb/gadget/composite.c
+++ b/drivers/usb/gadget/composite.c
@@ -438,9 +438,13 @@ static u8 encode_bMaxPower(enum usb_device_speed speed,
 	if (!val)
 		return 0;
 	if (speed < USB_SPEED_SUPER)
-		return DIV_ROUND_UP(val, 2);
+		return min(val, 500U) / 2;
 	else
-		return DIV_ROUND_UP(val, 8);
+		/*
+		 * USB 3.x supports up to 900mA, but since 900 isn't divisible
+		 * by 8 the integral division will effectively cap to 896mA.
+		 */
+		return min(val, 900U) / 8;
 }
 
 static int config_buf(struct usb_configuration *config,
@@ -838,6 +842,10 @@ static int set_config(struct usb_composite_dev *cdev,
 
 	/* when we return, be sure our power usage is valid */
 	power = c->MaxPower ? c->MaxPower : CONFIG_USB_GADGET_VBUS_DRAW;
+	if (gadget->speed < USB_SPEED_SUPER)
+		power = min(power, 500U);
+	else
+		power = min(power, 900U);
 done:
 	usb_gadget_vbus_draw(gadget, power);
 	if (result >= 0 && cdev->delayed_status)
@@ -2264,7 +2272,7 @@ void composite_resume(struct usb_gadget *gadget)
 {
 	struct usb_composite_dev	*cdev = get_gadget_data(gadget);
 	struct usb_function		*f;
-	u16				maxpower;
+	unsigned			maxpower;
 
 	/* REVISIT:  should we have config level
 	 * suspend/resume callbacks?
@@ -2278,10 +2286,14 @@ void composite_resume(struct usb_gadget *gadget)
 				f->resume(f);
 		}
 
-		maxpower = cdev->config->MaxPower;
+		maxpower = cdev->config->MaxPower ?
+			cdev->config->MaxPower : CONFIG_USB_GADGET_VBUS_DRAW;
+		if (gadget->speed < USB_SPEED_SUPER)
+			maxpower = min(maxpower, 500U);
+		else
+			maxpower = min(maxpower, 900U);
 
-		usb_gadget_vbus_draw(gadget, maxpower ?
-			maxpower : CONFIG_USB_GADGET_VBUS_DRAW);
+		usb_gadget_vbus_draw(gadget, maxpower);
 	}
 
 	cdev->suspended = 0;
-- 
2.20.1

[PATCH AUTOSEL 4.19 06/32] usb: gadget: ffs: ffs_aio_cancel(): Save/restore IRQ flags

[Sasha Levin]

From: Lars-Peter Clausen <lars@metafoo.de>

[ Upstream commit 43d565727a3a6fd24e37c7c2116475106af71806 ]

ffs_aio_cancel() can be called from both interrupt and thread context. Make
sure that the current IRQ state is saved and restored by using
spin_{un,}lock_irq{save,restore}().

Otherwise undefined behavior might occur.

Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/gadget/function/f_fs.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/usb/gadget/function/f_fs.c b/drivers/usb/gadget/function/f_fs.c
index 2050993fb58b7..a9239455eb6d8 100644
--- a/drivers/usb/gadget/function/f_fs.c
+++ b/drivers/usb/gadget/function/f_fs.c
@@ -1077,18 +1077,19 @@ static int ffs_aio_cancel(struct kiocb *kiocb)
 {
 	struct ffs_io_data *io_data = kiocb->private;
 	struct ffs_epfile *epfile = kiocb->ki_filp->private_data;
+	unsigned long flags;
 	int value;
 
 	ENTER();
 
-	spin_lock_irq(&epfile->ffs->eps_lock);
+	spin_lock_irqsave(&epfile->ffs->eps_lock, flags);
 
 	if (likely(io_data && io_data->ep && io_data->req))
 		value = usb_ep_dequeue(io_data->ep, io_data->req);
 	else
 		value = -EINVAL;
 
-	spin_unlock_irq(&epfile->ffs->eps_lock);
+	spin_unlock_irqrestore(&epfile->ffs->eps_lock, flags);
 
 	return value;
 }
-- 
2.20.1

[PATCH AUTOSEL 4.19 07/32] usb: gadget: serial: fix Tx stall after buffer overflow

[Sasha Levin]

From: Sergey Organov <sorganov@gmail.com>

[ Upstream commit e4bfded56cf39b8d02733c1e6ef546b97961e18a ]

Symptom: application opens /dev/ttyGS0 and starts sending (writing) to
it while either USB cable is not connected, or nobody listens on the
other side of the cable. If driver circular buffer overflows before
connection is established, no data will be written to the USB layer
until/unless /dev/ttyGS0 is closed and re-opened again by the
application (the latter besides having no means of being notified about
the event of establishing of the connection.)

Fix: on open and/or connect, kick Tx to flush circular buffer data to
USB layer.

Signed-off-by: Sergey Organov <sorganov@gmail.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/gadget/function/u_serial.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/gadget/function/u_serial.c b/drivers/usb/gadget/function/u_serial.c
index d4d317db89df5..38afe96c5cd26 100644
--- a/drivers/usb/gadget/function/u_serial.c
+++ b/drivers/usb/gadget/function/u_serial.c
@@ -567,8 +567,10 @@ static int gs_start_io(struct gs_port *port)
 	port->n_read = 0;
 	started = gs_start_rx(port);
 
-	/* unblock any pending writes into our circular buffer */
 	if (started) {
+		gs_start_tx(port);
+		/* Unblock any pending writes into our circular buffer, in case
+		 * we didn't in gs_start_tx() */
 		tty_wakeup(port->port.tty);
 	} else {
 		gs_free_requests(ep, head, &port->read_allocated);
-- 
2.20.1

[PATCH AUTOSEL 4.19 08/32] drm/msm/mdp5: rate limit pp done timeout warnings

[Sasha Levin]

From: Brian Masney <masneyb@onstation.org>

[ Upstream commit ef8c9809acb0805c991bba8bdd4749fc46d44a98 ]

Add rate limiting of the 'pp done time out' warnings since these
warnings can quickly fill the dmesg buffer.

Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c b/drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c
index b1da9ce543790..aa28a43ff842c 100644
--- a/drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c
+++ b/drivers/gpu/drm/msm/disp/mdp5/mdp5_crtc.c
@@ -1118,8 +1118,8 @@ static void mdp5_crtc_wait_for_pp_done(struct drm_crtc *crtc)
 	ret = wait_for_completion_timeout(&mdp5_crtc->pp_completion,
 						msecs_to_jiffies(50));
 	if (ret == 0)
-		dev_warn(dev->dev, "pp done time out, lm=%d\n",
-			 mdp5_cstate->pipeline.mixer->lm);
+		dev_warn_ratelimited(dev->dev, "pp done time out, lm=%d\n",
+				     mdp5_cstate->pipeline.mixer->lm);
 }
 
 static void mdp5_crtc_wait_for_flush_done(struct drm_crtc *crtc)
-- 
2.20.1

[PATCH AUTOSEL 4.19 09/32] drm: msm: Fix return type of dsi_mgr_connector_mode_valid for kCFI

[Sasha Levin]

From: John Stultz <john.stultz@linaro.org>

[ Upstream commit 7fd2dfc3694922eb7ace4801b7208cf9f62ebc7d ]

I was hitting kCFI crashes when building with clang, and after
some digging finally narrowed it down to the
dsi_mgr_connector_mode_valid() function being implemented as
returning an int, instead of an enum drm_mode_status.

This patch fixes it, and appeases the opaque word of the kCFI
gods (seriously, clang inlining everything makes the kCFI
backtraces only really rough estimates of where things went
wrong).

Thanks as always to Sami for his help narrowing this down.

Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Cc: Sami Tolvanen <samitolvanen@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Alistair Delva <adelva@google.com>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: freedreno@lists.freedesktop.org
Cc: clang-built-linux@googlegroups.com
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/msm/dsi/dsi_manager.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/msm/dsi/dsi_manager.c b/drivers/gpu/drm/msm/dsi/dsi_manager.c
index 5224010d90e4a..bd66d2aac41f7 100644
--- a/drivers/gpu/drm/msm/dsi/dsi_manager.c
+++ b/drivers/gpu/drm/msm/dsi/dsi_manager.c
@@ -328,7 +328,7 @@ static int dsi_mgr_connector_get_modes(struct drm_connector *connector)
 	return num;
 }
 
-static int dsi_mgr_connector_mode_valid(struct drm_connector *connector,
+static enum drm_mode_status dsi_mgr_connector_mode_valid(struct drm_connector *connector,
 				struct drm_display_mode *mode)
 {
 	int id = dsi_mgr_connector_get_id(connector);
-- 
2.20.1

[PATCH AUTOSEL 4.19 10/32] scsi: megaraid_sas: silence a warning

[Sasha Levin]

From: Tomas Henzl <thenzl@redhat.com>

[ Upstream commit 0e99b2c625da181aebf1a3d13493e3f7a5057a9c ]

Add a flag to DMA memory allocation to silence a warning.

This driver allocates DMA memory for IO frames. This allocation may exceed
MAX_ORDER pages for few megaraid_sas controllers (controllers with very
high queue depth). Consequently, the driver has logic to keep reducing the
controller queue depth until the DMA memory allocation succeeds.

On impacted megaraid_sas controllers there would be multiple DMA allocation
failures until driver settled on an allocation that fit. These failed DMA
allocation requests caused stack traces in system logs. These were not
harmful and this patch silences those warnings/stack traces.

[mkp: clarified commit desc]

Link: https://lore.kernel.org/r/20200204152413.7107-1-thenzl@redhat.com
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/megaraid/megaraid_sas_fusion.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/scsi/megaraid/megaraid_sas_fusion.c b/drivers/scsi/megaraid/megaraid_sas_fusion.c
index b094a4e55c32f..81bd824bb9d99 100644
--- a/drivers/scsi/megaraid/megaraid_sas_fusion.c
+++ b/drivers/scsi/megaraid/megaraid_sas_fusion.c
@@ -530,7 +530,8 @@ megasas_alloc_request_fusion(struct megasas_instance *instance)
 
 	fusion->io_request_frames =
 			dma_pool_alloc(fusion->io_request_frames_pool,
-				GFP_KERNEL, &fusion->io_request_frames_phys);
+				GFP_KERNEL | __GFP_NOWARN,
+				&fusion->io_request_frames_phys);
 	if (!fusion->io_request_frames) {
 		if (instance->max_fw_cmds >= (MEGASAS_REDUCE_QD_COUNT * 2)) {
 			instance->max_fw_cmds -= MEGASAS_REDUCE_QD_COUNT;
@@ -568,7 +569,7 @@ megasas_alloc_request_fusion(struct megasas_instance *instance)
 
 		fusion->io_request_frames =
 			dma_pool_alloc(fusion->io_request_frames_pool,
-				       GFP_KERNEL,
+				       GFP_KERNEL | __GFP_NOWARN,
 				       &fusion->io_request_frames_phys);
 
 		if (!fusion->io_request_frames) {
-- 
2.20.1

[PATCH AUTOSEL 4.19 11/32] drm/msm/dsi: save pll state before dsi host is powered off

[Sasha Levin]

From: Harigovindan P <harigovi@codeaurora.org>

[ Upstream commit a1028dcfd0dd97884072288d0c8ed7f30399b528 ]

Save pll state before dsi host is powered off. Without this change
some register values gets resetted.

Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/msm/dsi/dsi_manager.c | 5 +++++
 drivers/gpu/drm/msm/dsi/phy/dsi_phy.c | 4 ----
 2 files changed, 5 insertions(+), 4 deletions(-)

diff --git a/drivers/gpu/drm/msm/dsi/dsi_manager.c b/drivers/gpu/drm/msm/dsi/dsi_manager.c
index bd66d2aac41f7..b01762a7778ae 100644
--- a/drivers/gpu/drm/msm/dsi/dsi_manager.c
+++ b/drivers/gpu/drm/msm/dsi/dsi_manager.c
@@ -471,6 +471,7 @@ static void dsi_mgr_bridge_post_disable(struct drm_bridge *bridge)
 	struct msm_dsi *msm_dsi1 = dsi_mgr_get_dsi(DSI_1);
 	struct mipi_dsi_host *host = msm_dsi->host;
 	struct drm_panel *panel = msm_dsi->panel;
+	struct msm_dsi_pll *src_pll;
 	bool is_dual_dsi = IS_DUAL_DSI();
 	int ret;
 
@@ -511,6 +512,10 @@ static void dsi_mgr_bridge_post_disable(struct drm_bridge *bridge)
 								id, ret);
 	}
 
+	/* Save PLL status if it is a clock source */
+	src_pll = msm_dsi_phy_get_pll(msm_dsi->phy);
+	msm_dsi_pll_save_state(src_pll);
+
 	ret = msm_dsi_host_power_off(host);
 	if (ret)
 		pr_err("%s: host %d power off failed,%d\n", __func__, id, ret);
diff --git a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
index 9a9fa0c75a131..c630871de7c5b 100644
--- a/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
+++ b/drivers/gpu/drm/msm/dsi/phy/dsi_phy.c
@@ -726,10 +726,6 @@ void msm_dsi_phy_disable(struct msm_dsi_phy *phy)
 	if (!phy || !phy->cfg->ops.disable)
 		return;
 
-	/* Save PLL status if it is a clock source */
-	if (phy->usecase != MSM_DSI_PHY_SLAVE)
-		msm_dsi_pll_save_state(phy->pll);
-
 	phy->cfg->ops.disable(phy);
 
 	dsi_phy_regulator_disable(phy);
-- 
2.20.1

[PATCH AUTOSEL 4.19 12/32] drm/msm/dsi/pll: call vco set rate explicitly

[Sasha Levin]

From: Harigovindan P <harigovi@codeaurora.org>

[ Upstream commit c6659785dfb3f8d75f1fe637e4222ff8178f5280 ]

For a given byte clock, if VCO recalc value is exactly same as
vco set rate value, vco_set_rate does not get called assuming
VCO is already set to required value. But Due to GDSC toggle,
VCO values are erased in the HW. To make sure VCO is programmed
correctly, we forcefully call set_rate from vco_prepare.

Signed-off-by: Harigovindan P <harigovi@codeaurora.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c
index 31205625c7346..21a69b046625a 100644
--- a/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c
+++ b/drivers/gpu/drm/msm/dsi/pll/dsi_pll_10nm.c
@@ -406,6 +406,12 @@ static int dsi_pll_10nm_vco_prepare(struct clk_hw *hw)
 	if (pll_10nm->slave)
 		dsi_pll_enable_pll_bias(pll_10nm->slave);
 
+	rc = dsi_pll_10nm_vco_set_rate(hw,pll_10nm->vco_current_rate, 0);
+	if (rc) {
+		pr_err("vco_set_rate failed, rc=%d\n", rc);
+		return rc;
+	}
+
 	/* Start PLL */
 	pll_write(pll_10nm->phy_cmn_mmio + REG_DSI_10nm_PHY_CMN_PLL_CNTRL,
 		  0x01);
-- 
2.20.1

[PATCH AUTOSEL 4.19 13/32] selftests: forwarding: use proto icmp for {gretap, ip6gretap}_mac testing

[Sasha Levin]

From: Hangbin Liu <liuhangbin@gmail.com>

[ Upstream commit e8023b030ce1748930e2dc76353a262fe47d4745 ]

For tc ip_proto filter, when we extract the flow via __skb_flow_dissect()
without flag FLOW_DISSECTOR_F_STOP_AT_ENCAP, we will continue extract to
the inner proto.

So for GRE + ICMP messages, we should not track GRE proto, but inner ICMP
proto.

For test mirror_gre.sh, it may make user confused if we capture ICMP
message on $h3(since the flow is GRE message). So I move the capture
dev to h3-gt{4,6}, and only capture ICMP message.

Before the fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw)                            [ OK ]
TEST: egress mirror to gretap (skip_hw)                             [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw)                         [ OK ]
TEST: egress mirror to ip6gretap (skip_hw)                          [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw)              [FAIL]
 Expected to capture 10 packets, got 0.
TEST: egress mirror to gretap: envelope MAC (skip_hw)               [FAIL]
 Expected to capture 10 packets, got 0.
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw)           [FAIL]
 Expected to capture 10 packets, got 0.
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw)            [FAIL]
 Expected to capture 10 packets, got 0.
TEST: two simultaneously configured mirrors (skip_hw)               [ OK ]
WARN: Could not test offloaded functionality

After fix:
]# ./mirror_gre.sh
TEST: ingress mirror to gretap (skip_hw)                            [ OK ]
TEST: egress mirror to gretap (skip_hw)                             [ OK ]
TEST: ingress mirror to ip6gretap (skip_hw)                         [ OK ]
TEST: egress mirror to ip6gretap (skip_hw)                          [ OK ]
TEST: ingress mirror to gretap: envelope MAC (skip_hw)              [ OK ]
TEST: egress mirror to gretap: envelope MAC (skip_hw)               [ OK ]
TEST: ingress mirror to ip6gretap: envelope MAC (skip_hw)           [ OK ]
TEST: egress mirror to ip6gretap: envelope MAC (skip_hw)            [ OK ]
TEST: two simultaneously configured mirrors (skip_hw)               [ OK ]
WARN: Could not test offloaded functionality

Fixes: ba8d39871a10 ("selftests: forwarding: Add test for mirror to gretap")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Petr Machata <pmachata@gmail.com>
Tested-by: Petr Machata <pmachata@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../selftests/net/forwarding/mirror_gre.sh    | 25 ++++++++++---------
 1 file changed, 13 insertions(+), 12 deletions(-)

diff --git a/tools/testing/selftests/net/forwarding/mirror_gre.sh b/tools/testing/selftests/net/forwarding/mirror_gre.sh
index e6fd7a18c655f..0266443601bc0 100755
--- a/tools/testing/selftests/net/forwarding/mirror_gre.sh
+++ b/tools/testing/selftests/net/forwarding/mirror_gre.sh
@@ -63,22 +63,23 @@ test_span_gre_mac()
 {
 	local tundev=$1; shift
 	local direction=$1; shift
-	local prot=$1; shift
 	local what=$1; shift
 
-	local swp3mac=$(mac_get $swp3)
-	local h3mac=$(mac_get $h3)
+	case "$direction" in
+	ingress) local src_mac=$(mac_get $h1); local dst_mac=$(mac_get $h2)
+		;;
+	egress) local src_mac=$(mac_get $h2); local dst_mac=$(mac_get $h1)
+		;;
+	esac
 
 	RET=0
 
 	mirror_install $swp1 $direction $tundev "matchall $tcflags"
-	tc filter add dev $h3 ingress pref 77 prot $prot \
-		flower ip_proto 0x2f src_mac $swp3mac dst_mac $h3mac \
-		action pass
+	icmp_capture_install h3-${tundev} "src_mac $src_mac dst_mac $dst_mac"
 
-	mirror_test v$h1 192.0.2.1 192.0.2.2 $h3 77 10
+	mirror_test v$h1 192.0.2.1 192.0.2.2 h3-${tundev} 100 10
 
-	tc filter del dev $h3 ingress pref 77
+	icmp_capture_uninstall h3-${tundev}
 	mirror_uninstall $swp1 $direction
 
 	log_test "$direction $what: envelope MAC ($tcflags)"
@@ -120,14 +121,14 @@ test_ip6gretap()
 
 test_gretap_mac()
 {
-	test_span_gre_mac gt4 ingress ip "mirror to gretap"
-	test_span_gre_mac gt4 egress ip "mirror to gretap"
+	test_span_gre_mac gt4 ingress "mirror to gretap"
+	test_span_gre_mac gt4 egress "mirror to gretap"
 }
 
 test_ip6gretap_mac()
 {
-	test_span_gre_mac gt6 ingress ipv6 "mirror to ip6gretap"
-	test_span_gre_mac gt6 egress ipv6 "mirror to ip6gretap"
+	test_span_gre_mac gt6 ingress "mirror to ip6gretap"
+	test_span_gre_mac gt6 egress "mirror to ip6gretap"
 }
 
 test_all()
-- 
2.20.1

[PATCH AUTOSEL 4.19 14/32] net: atlantic: fix use after free kasan warn

[Sasha Levin]

From: Pavel Belous <pbelous@marvell.com>

[ Upstream commit a4980919ad6a7be548d499bc5338015e1a9191c6 ]

skb->len is used to calculate statistics after xmit invocation.

Under a stress load it may happen that skb will be xmited,
rx interrupt will come and skb will be freed, all before xmit function
is even returned.

Eventually, skb->len will access unallocated area.

Moving stats calculation into tx_clean routine.

Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Reported-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Pavel Belous <pbelous@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/aquantia/atlantic/aq_nic.c  | 4 ----
 drivers/net/ethernet/aquantia/atlantic/aq_ring.c | 7 +++++--
 2 files changed, 5 insertions(+), 6 deletions(-)

diff --git a/drivers/net/ethernet/aquantia/atlantic/aq_nic.c b/drivers/net/ethernet/aquantia/atlantic/aq_nic.c
index 8cc34b0bedc3a..d1de11b575f44 100644
--- a/drivers/net/ethernet/aquantia/atlantic/aq_nic.c
+++ b/drivers/net/ethernet/aquantia/atlantic/aq_nic.c
@@ -530,10 +530,6 @@ int aq_nic_xmit(struct aq_nic_s *self, struct sk_buff *skb)
 	if (likely(frags)) {
 		err = self->aq_hw_ops->hw_ring_tx_xmit(self->aq_hw,
 						       ring, frags);
-		if (err >= 0) {
-			++ring->stats.tx.packets;
-			ring->stats.tx.bytes += skb->len;
-		}
 	} else {
 		err = NETDEV_TX_BUSY;
 	}
diff --git a/drivers/net/ethernet/aquantia/atlantic/aq_ring.c b/drivers/net/ethernet/aquantia/atlantic/aq_ring.c
index b3c7994d73eb1..b03e5fd4327e3 100644
--- a/drivers/net/ethernet/aquantia/atlantic/aq_ring.c
+++ b/drivers/net/ethernet/aquantia/atlantic/aq_ring.c
@@ -162,9 +162,12 @@ bool aq_ring_tx_clean(struct aq_ring_s *self)
 			}
 		}
 
-		if (unlikely(buff->is_eop))
-			dev_kfree_skb_any(buff->skb);
+		if (unlikely(buff->is_eop)) {
+			++self->stats.rx.packets;
+			self->stats.tx.bytes += buff->skb->len;
 
+			dev_kfree_skb_any(buff->skb);
+		}
 		buff->pa = 0U;
 		buff->eop_index = 0xffffU;
 		self->sw_head = aq_ring_next_dx(self, self->sw_head);
-- 
2.20.1

[PATCH AUTOSEL 4.19 15/32] net: atlantic: fix potential error handling

[Sasha Levin]

From: Pavel Belous <pbelous@marvell.com>

[ Upstream commit 380ec5b9af7f0d57dbf6ac067fd9f33cff2fef71 ]

Code inspection found that in case of mapping error we do return current
'ret' value. But beside error, it is used to count number of descriptors
allocated for the packet. In that case map_skb function could return '1'.

Changing it to return zero (number of mapped descriptors for skb)

Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Pavel Belous <pbelous@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/aquantia/atlantic/aq_nic.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/aquantia/atlantic/aq_nic.c b/drivers/net/ethernet/aquantia/atlantic/aq_nic.c
index d1de11b575f44..15dcfb6704e5b 100644
--- a/drivers/net/ethernet/aquantia/atlantic/aq_nic.c
+++ b/drivers/net/ethernet/aquantia/atlantic/aq_nic.c
@@ -399,8 +399,10 @@ static unsigned int aq_nic_map_skb(struct aq_nic_s *self,
 				     dx_buff->len,
 				     DMA_TO_DEVICE);
 
-	if (unlikely(dma_mapping_error(aq_nic_get_dev(self), dx_buff->pa)))
+	if (unlikely(dma_mapping_error(aq_nic_get_dev(self), dx_buff->pa))) {
+		ret = 0;
 		goto exit;
+	}
 
 	first = dx_buff;
 	dx_buff->len_pkt = skb->len;
-- 
2.20.1

[PATCH AUTOSEL 4.19 16/32] net: phy: restore mdio regs in the iproc mdio driver

[Sasha Levin]

From: Arun Parameswaran <arun.parameswaran@broadcom.com>

[ Upstream commit 6f08e98d62799e53c89dbf2c9a49d77e20ca648c ]

The mii management register in iproc mdio block
does not have a retention register so it is lost on suspend.
Save and restore value of register while resuming from suspend.

Fixes: bb1a619735b4 ("net: phy: Initialize mdio clock at probe function")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/phy/mdio-bcm-iproc.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/drivers/net/phy/mdio-bcm-iproc.c b/drivers/net/phy/mdio-bcm-iproc.c
index 46fe1ae919a30..51ce3ea17fb37 100644
--- a/drivers/net/phy/mdio-bcm-iproc.c
+++ b/drivers/net/phy/mdio-bcm-iproc.c
@@ -188,6 +188,23 @@ static int iproc_mdio_remove(struct platform_device *pdev)
 	return 0;
 }
 
+#ifdef CONFIG_PM_SLEEP
+int iproc_mdio_resume(struct device *dev)
+{
+	struct platform_device *pdev = to_platform_device(dev);
+	struct iproc_mdio_priv *priv = platform_get_drvdata(pdev);
+
+	/* restore the mii clock configuration */
+	iproc_mdio_config_clk(priv->base);
+
+	return 0;
+}
+
+static const struct dev_pm_ops iproc_mdio_pm_ops = {
+	.resume = iproc_mdio_resume
+};
+#endif /* CONFIG_PM_SLEEP */
+
 static const struct of_device_id iproc_mdio_of_match[] = {
 	{ .compatible = "brcm,iproc-mdio", },
 	{ /* sentinel */ },
@@ -198,6 +215,9 @@ static struct platform_driver iproc_mdio_driver = {
 	.driver = {
 		.name = "iproc-mdio",
 		.of_match_table = iproc_mdio_of_match,
+#ifdef CONFIG_PM_SLEEP
+		.pm = &iproc_mdio_pm_ops,
+#endif
 	},
 	.probe = iproc_mdio_probe,
 	.remove = iproc_mdio_remove,
-- 
2.20.1

[PATCH AUTOSEL 4.19 17/32] net: dsa: b53: Ensure the default VID is untagged

[Sasha Levin]

From: Florian Fainelli <f.fainelli@gmail.com>

[ Upstream commit d965a5432d4c3e6b9c3d2bc1d4a800013bbf76f6 ]

We need to ensure that the default VID is untagged otherwise the switch
will be sending tagged frames and the results can be problematic. This
is especially true with b53 switches that use VID 0 as their default
VLAN since VID 0 has a special meaning.

Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID")
Fixes: 061f6a505ac3 ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/dsa/b53/b53_common.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/net/dsa/b53/b53_common.c b/drivers/net/dsa/b53/b53_common.c
index 51436e7eae103..ac5d945b934a0 100644
--- a/drivers/net/dsa/b53/b53_common.c
+++ b/drivers/net/dsa/b53/b53_common.c
@@ -1165,6 +1165,9 @@ void b53_vlan_add(struct dsa_switch *ds, int port,
 
 		b53_get_vlan_entry(dev, vid, vl);
 
+		if (vid == 0 && vid == b53_default_pvid(dev))
+			untagged = true;
+
 		vl->members |= BIT(port);
 		if (untagged && !dsa_is_cpu_port(ds, port))
 			vl->untag |= BIT(port);
-- 
2.20.1

[PATCH AUTOSEL 4.19 18/32] net: ks8851-ml: Remove 8-bit bus accessors

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 69233bba6543a37755158ca3382765387b8078df ]

This driver is mixing 8-bit and 16-bit bus accessors for reasons unknown,
however the speculation is that this was some sort of attempt to support
the 8-bit bus mode.

As per the KS8851-16MLL documentation, all two registers accessed via the
8-bit accessors are internally 16-bit registers, so reading them using
16-bit accessors is fine. The KS_CCR read can be converted to 16-bit read
outright, as it is already a concatenation of two 8-bit reads of that
register. The KS_RXQCR accesses are 8-bit only, however writing the top
8 bits of the register is OK as well, since the driver caches the entire
16-bit register value anyway.

Finally, the driver is not used by any hardware in the kernel right now.
The only hardware available to me is one with 16-bit bus, so I have no
way to test the 8-bit bus mode, however it is unlikely this ever really
worked anyway. If the 8-bit bus mode is ever required, it can be easily
added by adjusting the 16-bit accessors to do 2 consecutive accesses,
which is how this should have been done from the beginning.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/micrel/ks8851_mll.c | 45 +++---------------------
 1 file changed, 5 insertions(+), 40 deletions(-)

diff --git a/drivers/net/ethernet/micrel/ks8851_mll.c b/drivers/net/ethernet/micrel/ks8851_mll.c
index 35f8c9ef204d9..29ac83f4683a6 100644
--- a/drivers/net/ethernet/micrel/ks8851_mll.c
+++ b/drivers/net/ethernet/micrel/ks8851_mll.c
@@ -475,24 +475,6 @@ static int msg_enable;
  * chip is busy transferring packet data (RX/TX FIFO accesses).
  */
 
-/**
- * ks_rdreg8 - read 8 bit register from device
- * @ks	  : The chip information
- * @offset: The register address
- *
- * Read a 8bit register from the chip, returning the result
- */
-static u8 ks_rdreg8(struct ks_net *ks, int offset)
-{
-	u16 data;
-	u8 shift_bit = offset & 0x03;
-	u8 shift_data = (offset & 1) << 3;
-	ks->cmd_reg_cache = (u16) offset | (u16)(BE0 << shift_bit);
-	iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
-	data  = ioread16(ks->hw_addr);
-	return (u8)(data >> shift_data);
-}
-
 /**
  * ks_rdreg16 - read 16 bit register from device
  * @ks	  : The chip information
@@ -508,22 +490,6 @@ static u16 ks_rdreg16(struct ks_net *ks, int offset)
 	return ioread16(ks->hw_addr);
 }
 
-/**
- * ks_wrreg8 - write 8bit register value to chip
- * @ks: The chip information
- * @offset: The register address
- * @value: The value to write
- *
- */
-static void ks_wrreg8(struct ks_net *ks, int offset, u8 value)
-{
-	u8  shift_bit = (offset & 0x03);
-	u16 value_write = (u16)(value << ((offset & 1) << 3));
-	ks->cmd_reg_cache = (u16)offset | (BE0 << shift_bit);
-	iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
-	iowrite16(value_write, ks->hw_addr);
-}
-
 /**
  * ks_wrreg16 - write 16bit register value to chip
  * @ks: The chip information
@@ -643,8 +609,7 @@ static void ks_read_config(struct ks_net *ks)
 	u16 reg_data = 0;
 
 	/* Regardless of bus width, 8 bit read should always work.*/
-	reg_data = ks_rdreg8(ks, KS_CCR) & 0x00FF;
-	reg_data |= ks_rdreg8(ks, KS_CCR+1) << 8;
+	reg_data = ks_rdreg16(ks, KS_CCR);
 
 	/* addr/data bus are multiplexed */
 	ks->sharedbus = (reg_data & CCR_SHARED) == CCR_SHARED;
@@ -748,7 +713,7 @@ static inline void ks_read_qmu(struct ks_net *ks, u16 *buf, u32 len)
 
 	/* 1. set sudo DMA mode */
 	ks_wrreg16(ks, KS_RXFDPR, RXFDPR_RXFPAI);
-	ks_wrreg8(ks, KS_RXQCR, (ks->rc_rxqcr | RXQCR_SDA) & 0xff);
+	ks_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA);
 
 	/* 2. read prepend data */
 	/**
@@ -765,7 +730,7 @@ static inline void ks_read_qmu(struct ks_net *ks, u16 *buf, u32 len)
 	ks_inblk(ks, buf, ALIGN(len, 4));
 
 	/* 4. reset sudo DMA Mode */
-	ks_wrreg8(ks, KS_RXQCR, ks->rc_rxqcr);
+	ks_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
 }
 
 /**
@@ -998,13 +963,13 @@ static void ks_write_qmu(struct ks_net *ks, u8 *pdata, u16 len)
 	ks->txh.txw[1] = cpu_to_le16(len);
 
 	/* 1. set sudo-DMA mode */
-	ks_wrreg8(ks, KS_RXQCR, (ks->rc_rxqcr | RXQCR_SDA) & 0xff);
+	ks_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr | RXQCR_SDA);
 	/* 2. write status/lenth info */
 	ks_outblk(ks, ks->txh.txw, 4);
 	/* 3. write pkt data */
 	ks_outblk(ks, (u16 *)pdata, ALIGN(len, 4));
 	/* 4. reset sudo-DMA mode */
-	ks_wrreg8(ks, KS_RXQCR, ks->rc_rxqcr);
+	ks_wrreg16(ks, KS_RXQCR, ks->rc_rxqcr);
 	/* 5. Enqueue Tx(move the pkt from TX buffer into TXQ) */
 	ks_wrreg16(ks, KS_TXQCR, TXQCR_METFE);
 	/* 6. wait until TXQCR_METFE is auto-cleared */
-- 
2.20.1

[PATCH AUTOSEL 4.19 19/32] net: ks8851-ml: Fix 16-bit data access

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit edacb098ea9c31589276152f09b4439052c0f2b1 ]

The packet data written to and read from Micrel KSZ8851-16MLLI must be
byte-swapped in 16-bit mode, add this byte-swapping.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/micrel/ks8851_mll.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/micrel/ks8851_mll.c b/drivers/net/ethernet/micrel/ks8851_mll.c
index 29ac83f4683a6..aff1619fb0e0e 100644
--- a/drivers/net/ethernet/micrel/ks8851_mll.c
+++ b/drivers/net/ethernet/micrel/ks8851_mll.c
@@ -516,7 +516,7 @@ static inline void ks_inblk(struct ks_net *ks, u16 *wptr, u32 len)
 {
 	len >>= 1;
 	while (len--)
-		*wptr++ = (u16)ioread16(ks->hw_addr);
+		*wptr++ = be16_to_cpu(ioread16(ks->hw_addr));
 }
 
 /**
@@ -530,7 +530,7 @@ static inline void ks_outblk(struct ks_net *ks, u16 *wptr, u32 len)
 {
 	len >>= 1;
 	while (len--)
-		iowrite16(*wptr++, ks->hw_addr);
+		iowrite16(cpu_to_be16(*wptr++), ks->hw_addr);
 }
 
 static void ks_disable_int(struct ks_net *ks)
-- 
2.20.1

[PATCH AUTOSEL 4.19 20/32] net: ks8851-ml: Fix 16-bit IO operation

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 58292104832fef6cb4a89f736012c0e0724c3442 ]

The Micrel KSZ8851-16MLLI datasheet DS00002357B page 12 states that
BE[3:0] signals are active high. This contradicts the measurements
of the behavior of the actual chip, where these signals behave as
active low. For example, to read the CIDER register, the bus must
expose 0xc0c0 during the address phase, which means BE[3:0]=4'b1100.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David S. Miller <davem@davemloft.net>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Petr Stetiar <ynezz@true.cz>
Cc: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/micrel/ks8851_mll.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/net/ethernet/micrel/ks8851_mll.c b/drivers/net/ethernet/micrel/ks8851_mll.c
index aff1619fb0e0e..9de59facec218 100644
--- a/drivers/net/ethernet/micrel/ks8851_mll.c
+++ b/drivers/net/ethernet/micrel/ks8851_mll.c
@@ -485,7 +485,7 @@ static int msg_enable;
 
 static u16 ks_rdreg16(struct ks_net *ks, int offset)
 {
-	ks->cmd_reg_cache = (u16)offset | ((BE1 | BE0) << (offset & 0x02));
+	ks->cmd_reg_cache = (u16)offset | ((BE3 | BE2) >> (offset & 0x02));
 	iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
 	return ioread16(ks->hw_addr);
 }
@@ -500,7 +500,7 @@ static u16 ks_rdreg16(struct ks_net *ks, int offset)
 
 static void ks_wrreg16(struct ks_net *ks, int offset, u16 value)
 {
-	ks->cmd_reg_cache = (u16)offset | ((BE1 | BE0) << (offset & 0x02));
+	ks->cmd_reg_cache = (u16)offset | ((BE3 | BE2) >> (offset & 0x02));
 	iowrite16(ks->cmd_reg_cache, ks->hw_addr_cmd);
 	iowrite16(value, ks->hw_addr);
 }
-- 
2.20.1

[PATCH AUTOSEL 4.19 21/32] watchdog: da9062: do not ping the hw during stop()

[Sasha Levin]

From: Marco Felsch <m.felsch@pengutronix.de>

[ Upstream commit e9a0e65eda3f78d0b04ec6136c591c000cbc3b76 ]

The da9062 hw has a minimum ping cool down phase of at least 200ms. The
driver takes that into account by setting the min_hw_heartbeat_ms to
300ms and the core guarantees that the hw limit is observed for the
ping() calls. But the core can't guarantee the required minimum ping
cool down phase if a stop() command is send immediately after the ping()
command. So it is not allowed to ping the watchdog within the stop()
command as the driver does. Remove the ping can be done without doubts
because the watchdog gets disabled anyway and a (re)start resets the
watchdog counter too.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200120091729.16256-1-m.felsch@pengutronix.de
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/watchdog/da9062_wdt.c | 7 -------
 1 file changed, 7 deletions(-)

diff --git a/drivers/watchdog/da9062_wdt.c b/drivers/watchdog/da9062_wdt.c
index fe169d8e1fb2f..7f0a8e6352860 100644
--- a/drivers/watchdog/da9062_wdt.c
+++ b/drivers/watchdog/da9062_wdt.c
@@ -99,13 +99,6 @@ static int da9062_wdt_stop(struct watchdog_device *wdd)
 	struct da9062_watchdog *wdt = watchdog_get_drvdata(wdd);
 	int ret;
 
-	ret = da9062_reset_watchdog_timer(wdt);
-	if (ret) {
-		dev_err(wdt->hw->dev, "Failed to ping the watchdog (err = %d)\n",
-			ret);
-		return ret;
-	}
-
 	ret = regmap_update_bits(wdt->hw->regmap,
 				 DA9062AA_CONTROL_D,
 				 DA9062AA_TWDSCALE_MASK,
-- 
2.20.1

[PATCH AUTOSEL 4.19 22/32] s390/cio: cio_ignore_proc_seq_next should increase position index

[Sasha Levin]

From: Vasily Averin <vvs@virtuozzo.com>

[ Upstream commit 8b101a5e14f2161869636ff9cb4907b7749dc0c2 ]

if seq_file .next fuction does not change position index,
read after some lseek can generate unexpected output.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=206283
Link: https://lore.kernel.org/r/d44c53a7-9bc1-15c7-6d4a-0c10cb9dffce@virtuozzo.com
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/s390/cio/blacklist.c | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/drivers/s390/cio/blacklist.c b/drivers/s390/cio/blacklist.c
index 2a3f874a21d54..9cebff8e8d740 100644
--- a/drivers/s390/cio/blacklist.c
+++ b/drivers/s390/cio/blacklist.c
@@ -303,8 +303,10 @@ static void *
 cio_ignore_proc_seq_next(struct seq_file *s, void *it, loff_t *offset)
 {
 	struct ccwdev_iter *iter;
+	loff_t p = *offset;
 
-	if (*offset >= (__MAX_SUBCHANNEL + 1) * (__MAX_SSID + 1))
+	(*offset)++;
+	if (p >= (__MAX_SUBCHANNEL + 1) * (__MAX_SSID + 1))
 		return NULL;
 	iter = it;
 	if (iter->devno == __MAX_SUBCHANNEL) {
@@ -314,7 +316,6 @@ cio_ignore_proc_seq_next(struct seq_file *s, void *it, loff_t *offset)
 			return NULL;
 	} else
 		iter->devno++;
-	(*offset)++;
 	return iter;
 }
 
-- 
2.20.1

[PATCH AUTOSEL 4.19 23/32] s390: make 'install' not depend on vmlinux

[Sasha Levin]

From: Masahiro Yamada <masahiroy@kernel.org>

[ Upstream commit 94e90f727f7424d827256023cace829cad6896f4 ]

For the same reason as commit 19514fc665ff ("arm, kbuild: make "make
install" not depend on vmlinux"), the install targets should never
trigger the rebuild of the kernel.

The variable, CONFIGURE, is not set by anyone. Remove it as well.

Link: https://lkml.kernel.org/r/20200216144829.27023-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/s390/Makefile      | 2 +-
 arch/s390/boot/Makefile | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/s390/Makefile b/arch/s390/Makefile
index 4bccde36cb161..9a3a698c8fca5 100644
--- a/arch/s390/Makefile
+++ b/arch/s390/Makefile
@@ -140,7 +140,7 @@ all: bzImage
 #KBUILD_IMAGE is necessary for packaging targets like rpm-pkg, deb-pkg...
 KBUILD_IMAGE	:= $(boot)/bzImage
 
-install: vmlinux
+install:
 	$(Q)$(MAKE) $(build)=$(boot) $@
 
 bzImage: vmlinux
diff --git a/arch/s390/boot/Makefile b/arch/s390/boot/Makefile
index f6a9b0c203553..45c72d1f9e7d2 100644
--- a/arch/s390/boot/Makefile
+++ b/arch/s390/boot/Makefile
@@ -46,7 +46,7 @@ quiet_cmd_ar = AR      $@
 $(obj)/startup.a: $(OBJECTS) FORCE
 	$(call if_changed,ar)
 
-install: $(CONFIGURE) $(obj)/bzImage
+install:
 	sh -x  $(srctree)/$(obj)/install.sh $(KERNELRELEASE) $(obj)/bzImage \
 	      System.map "$(INSTALL_PATH)"
 
-- 
2.20.1

[PATCH AUTOSEL 4.19 24/32] net: mscc: fix in frame extraction

[Sasha Levin]

From: Horatiu Vultur <horatiu.vultur@microchip.com>

[ Upstream commit a81541041ceb55bcec9a8bb8ad3482263f0a205a ]

Each extracted frame on Ocelot has an IFH. The frame and IFH are extracted
by reading chuncks of 4 bytes from a register.

In case the IFH and frames were read corretly it would try to read the next
frame. In case there are no more frames in the queue, it checks if there
were any previous errors and in that case clear the queue. But this check
will always succeed also when there are no errors. Because when extracting
the IFH the error is checked against 4(number of bytes read) and then the
error is set only if the extraction of the frame failed. So in a happy case
where there are no errors the err variable is still 4. So it could be
a case where after the check that there are no more frames in the queue, a
frame will arrive in the queue but because the error is not reseted, it
would try to flush the queue. So the frame will be lost.

The fix consist in resetting the error after reading the IFH.

Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/mscc/ocelot_board.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/drivers/net/ethernet/mscc/ocelot_board.c b/drivers/net/ethernet/mscc/ocelot_board.c
index 3cdf63e35b53b..4054cf9db8181 100644
--- a/drivers/net/ethernet/mscc/ocelot_board.c
+++ b/drivers/net/ethernet/mscc/ocelot_board.c
@@ -105,6 +105,14 @@ static irqreturn_t ocelot_xtr_irq_handler(int irq, void *arg)
 		if (err != 4)
 			break;
 
+		/* At this point the IFH was read correctly, so it is safe to
+		 * presume that there is no error. The err needs to be reset
+		 * otherwise a frame could come in CPU queue between the while
+		 * condition and the check for error later on. And in that case
+		 * the new frame is just removed and not processed.
+		 */
+		err = 0;
+
 		ocelot_parse_ifh(ifh, &info);
 
 		dev = ocelot->ports[info.port]->dev;
-- 
2.20.1

[PATCH AUTOSEL 4.19 25/32] x86/boot/compressed: Don't declare __force_order in kaslr_64.c

[Sasha Levin]

From: "H.J. Lu" <hjl.tools@gmail.com>

[ Upstream commit df6d4f9db79c1a5d6f48b59db35ccd1e9ff9adfc ]

GCC 10 changed the default to -fno-common, which leads to

    LD      arch/x86/boot/compressed/vmlinux
  ld: arch/x86/boot/compressed/pgtable_64.o:(.bss+0x0): multiple definition of `__force_order'; \
    arch/x86/boot/compressed/kaslr_64.o:(.bss+0x0): first defined here
  make[2]: *** [arch/x86/boot/compressed/Makefile:119: arch/x86/boot/compressed/vmlinux] Error 1

Since __force_order is already provided in pgtable_64.c, there is no
need to declare __force_order in kaslr_64.c.

Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200124181811.4780-1-hjl.tools@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/x86/boot/compressed/kaslr_64.c | 3 ---
 1 file changed, 3 deletions(-)

diff --git a/arch/x86/boot/compressed/kaslr_64.c b/arch/x86/boot/compressed/kaslr_64.c
index 748456c365f46..9557c5a15b91e 100644
--- a/arch/x86/boot/compressed/kaslr_64.c
+++ b/arch/x86/boot/compressed/kaslr_64.c
@@ -29,9 +29,6 @@
 #define __PAGE_OFFSET __PAGE_OFFSET_BASE
 #include "../../mm/ident_map.c"
 
-/* Used by pgtable.h asm code to force instruction serialization. */
-unsigned long __force_order;
-
 /* Used to track our page table allocation area. */
 struct alloc_pgt_data {
 	unsigned char *pgt_buf;
-- 
2.20.1

[PATCH AUTOSEL 4.19 26/32] s390/qdio: fill SL with absolute addresses

[Sasha Levin]

From: Julian Wiedmann <jwi@linux.ibm.com>

[ Upstream commit e9091ffd6a0aaced111b5d6ead5eaab5cd7101bc ]

As the comment says, sl->sbal holds an absolute address. qeth currently
solves this through wild casting, while zfcp doesn't care.

Handle this properly in the code that actually builds the SL.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Steffen Maier <maier@linux.ibm.com> [for qdio]
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/s390/include/asm/qdio.h      |  2 +-
 drivers/s390/cio/qdio_setup.c     |  3 ++-
 drivers/s390/net/qeth_core_main.c | 23 +++++++++++------------
 3 files changed, 14 insertions(+), 14 deletions(-)

diff --git a/arch/s390/include/asm/qdio.h b/arch/s390/include/asm/qdio.h
index 9c9970a5dfb10..1f2cd98dcb058 100644
--- a/arch/s390/include/asm/qdio.h
+++ b/arch/s390/include/asm/qdio.h
@@ -228,7 +228,7 @@ struct qdio_buffer {
  * @sbal: absolute SBAL address
  */
 struct sl_element {
-	unsigned long sbal;
+	u64 sbal;
 } __attribute__ ((packed));
 
 /**
diff --git a/drivers/s390/cio/qdio_setup.c b/drivers/s390/cio/qdio_setup.c
index 034528a5453ec..d040c4920ee78 100644
--- a/drivers/s390/cio/qdio_setup.c
+++ b/drivers/s390/cio/qdio_setup.c
@@ -8,6 +8,7 @@
 #include <linux/kernel.h>
 #include <linux/slab.h>
 #include <linux/export.h>
+#include <linux/io.h>
 #include <asm/qdio.h>
 
 #include "cio.h"
@@ -208,7 +209,7 @@ static void setup_storage_lists(struct qdio_q *q, struct qdio_irq *irq_ptr,
 
 	/* fill in sl */
 	for (j = 0; j < QDIO_MAX_BUFFERS_PER_Q; j++)
-		q->sl->element[j].sbal = (unsigned long)q->sbal[j];
+		q->sl->element[j].sbal = virt_to_phys(q->sbal[j]);
 }
 
 static void setup_queues(struct qdio_irq *irq_ptr,
diff --git a/drivers/s390/net/qeth_core_main.c b/drivers/s390/net/qeth_core_main.c
index 81e2c591acb0b..d99bfbfcafb76 100644
--- a/drivers/s390/net/qeth_core_main.c
+++ b/drivers/s390/net/qeth_core_main.c
@@ -4929,10 +4929,10 @@ static void qeth_qdio_establish_cq(struct qeth_card *card,
 	if (card->options.cq == QETH_CQ_ENABLED) {
 		int offset = QDIO_MAX_BUFFERS_PER_Q *
 			     (card->qdio.no_in_queues - 1);
-		for (i = 0; i < QDIO_MAX_BUFFERS_PER_Q; ++i) {
-			in_sbal_ptrs[offset + i] = (struct qdio_buffer *)
-				virt_to_phys(card->qdio.c_q->bufs[i].buffer);
-		}
+
+		for (i = 0; i < QDIO_MAX_BUFFERS_PER_Q; i++)
+			in_sbal_ptrs[offset + i] =
+				card->qdio.c_q->bufs[i].buffer;
 
 		queue_start_poll[card->qdio.no_in_queues - 1] = NULL;
 	}
@@ -4967,10 +4967,9 @@ static int qeth_qdio_establish(struct qeth_card *card)
 		rc = -ENOMEM;
 		goto out_free_qib_param;
 	}
-	for (i = 0; i < QDIO_MAX_BUFFERS_PER_Q; ++i) {
-		in_sbal_ptrs[i] = (struct qdio_buffer *)
-			virt_to_phys(card->qdio.in_q->bufs[i].buffer);
-	}
+
+	for (i = 0; i < QDIO_MAX_BUFFERS_PER_Q; i++)
+		in_sbal_ptrs[i] = card->qdio.in_q->bufs[i].buffer;
 
 	queue_start_poll = kcalloc(card->qdio.no_in_queues, sizeof(void *),
 				   GFP_KERNEL);
@@ -4991,11 +4990,11 @@ static int qeth_qdio_establish(struct qeth_card *card)
 		rc = -ENOMEM;
 		goto out_free_queue_start_poll;
 	}
+
 	for (i = 0, k = 0; i < card->qdio.no_out_queues; ++i)
-		for (j = 0; j < QDIO_MAX_BUFFERS_PER_Q; ++j, ++k) {
-			out_sbal_ptrs[k] = (struct qdio_buffer *)virt_to_phys(
-				card->qdio.out_qs[i]->bufs[j]->buffer);
-		}
+		for (j = 0; j < QDIO_MAX_BUFFERS_PER_Q; j++, k++)
+			out_sbal_ptrs[k] =
+				card->qdio.out_qs[i]->bufs[j]->buffer;
 
 	memset(&init_data, 0, sizeof(struct qdio_initialize));
 	init_data.cdev                   = CARD_DDEV(card);
-- 
2.20.1

[PATCH AUTOSEL 4.19 27/32] nvme: Fix uninitialized-variable warning

[Sasha Levin]

From: Keith Busch <kbusch@kernel.org>

[ Upstream commit 15755854d53b4bbb0bb37a0fce66f0156cfc8a17 ]

gcc may detect a false positive on nvme using an unintialized variable
if setting features fails. Since this is not a fast path, explicitly
initialize this variable to suppress the warning.

Reported-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/nvme/host/core.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/nvme/host/core.c b/drivers/nvme/host/core.c
index f41fd15b7b7c2..a8132e8d72bb4 100644
--- a/drivers/nvme/host/core.c
+++ b/drivers/nvme/host/core.c
@@ -1058,8 +1058,8 @@ static struct nvme_id_ns *nvme_identify_ns(struct nvme_ctrl *ctrl,
 static int nvme_set_features(struct nvme_ctrl *dev, unsigned fid, unsigned dword11,
 		      void *buffer, size_t buflen, u32 *result)
 {
+	union nvme_result res = { 0 };
 	struct nvme_command c;
-	union nvme_result res;
 	int ret;
 
 	memset(&c, 0, sizeof(c));
-- 
2.20.1

[PATCH AUTOSEL 4.19 28/32] nfc: pn544: Fix occasional HW initialization failure

[Sasha Levin]

From: Dmitry Osipenko <digetx@gmail.com>

[ Upstream commit c3331d2fe3fd4d5e321f2467d01f72de7edfb5d0 ]

The PN544 driver checks the "enable" polarity during of driver's probe and
it's doing that by turning ON and OFF NFC with different polarities until
enabling succeeds. It takes some time for the hardware to power-down, and
thus, to deassert the IRQ that is raised by turning ON the hardware.
Since the delay after last power-down of the polarity-checking process is
missed in the code, the interrupt may trigger immediately after installing
the IRQ handler (right after the checking is done), which results in IRQ
handler trying to touch the disabled HW and ends with marking NFC as
'DEAD' during of the driver's probe:

  pn544_hci_i2c 1-002a: NFC: nfc_en polarity : active high
  pn544_hci_i2c 1-002a: NFC: invalid len byte
  shdlc: llc_shdlc_recv_frame: NULL Frame -> link is dead

This patch fixes the occasional NFC initialization failure on Nexus 7
device.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/nfc/pn544/i2c.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/nfc/pn544/i2c.c b/drivers/nfc/pn544/i2c.c
index d0207f8e68b7c..dcef73eb41206 100644
--- a/drivers/nfc/pn544/i2c.c
+++ b/drivers/nfc/pn544/i2c.c
@@ -236,6 +236,7 @@ static void pn544_hci_i2c_platform_init(struct pn544_i2c_phy *phy)
 
 out:
 	gpiod_set_value_cansleep(phy->gpiod_en, !phy->en_polarity);
+	usleep_range(10000, 15000);
 }
 
 static void pn544_hci_i2c_enable_mode(struct pn544_i2c_phy *phy, int run_mode)
-- 
2.20.1

[PATCH AUTOSEL 4.19 29/32] ice: Don't tell the OS that link is going down

[Sasha Levin]

From: Michal Swiatkowski <michal.swiatkowski@intel.com>

[ Upstream commit 8a55c08d3bbc9ffc9639f69f742e59ebd99f913b ]

Remove code that tell the OS that link is going down when user
change flow control via ethtool. When link is up it isn't certain
that link goes down after 0x0605 aq command. If link doesn't go
down, OS thinks that link is down, but physical link is up. To
reset this state user have to take interface down and up.

If link goes down after 0x0605 command, FW send information
about that and after that driver tells the OS that the link goes
down. So this code in ethtool is unnecessary.

Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/intel/ice/ice_ethtool.c | 7 -------
 1 file changed, 7 deletions(-)

diff --git a/drivers/net/ethernet/intel/ice/ice_ethtool.c b/drivers/net/ethernet/intel/ice/ice_ethtool.c
index 4c5c87b158f55..627abef829c9a 100644
--- a/drivers/net/ethernet/intel/ice/ice_ethtool.c
+++ b/drivers/net/ethernet/intel/ice/ice_ethtool.c
@@ -772,13 +772,6 @@ ice_set_pauseparam(struct net_device *netdev, struct ethtool_pauseparam *pause)
 	else
 		return -EINVAL;
 
-	/* Tell the OS link is going down, the link will go back up when fw
-	 * says it is ready asynchronously
-	 */
-	ice_print_link_msg(vsi, false);
-	netif_carrier_off(netdev);
-	netif_tx_stop_all_queues(netdev);
-
 	/* Set the FC mode and only restart AN if link is up */
 	status = ice_set_fc(pi, &aq_failures, link_up);
 
-- 
2.20.1

[PATCH AUTOSEL 4.19 30/32] x86/xen: Distribute switch variables for initialization

[Sasha Levin]

From: Kees Cook <keescook@chromium.org>

[ Upstream commit 9038ec99ceb94fb8d93ade5e236b2928f0792c7c ]

Variables declared in a switch statement before any case statements
cannot be automatically initialized with compiler instrumentation (as
they are not part of any execution flow). With GCC's proposed automatic
stack variable initialization feature, this triggers a warning (and they
don't get initialized). Clang's automatic stack variable initialization
(via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also
doesn't initialize such variables[1]. Note that these warnings (or silent
skipping) happen before the dead-store elimination optimization phase,
so even when the automatic initializations are later elided in favor of
direct initializations, the warnings remain.

To avoid these problems, move such variables into the "case" where
they're used or lift them up into the main function body.

arch/x86/xen/enlighten_pv.c: In function ‘xen_write_msr_safe’:
arch/x86/xen/enlighten_pv.c:904:12: warning: statement will never be executed [-Wswitch-unreachable]
  904 |   unsigned which;
      |            ^~~~~

[1] https://bugs.llvm.org/show_bug.cgi?id=44916

Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20200220062318.69299-1-keescook@chromium.org
Reviewed-by: Juergen Gross <jgross@suse.com>
[boris: made @which an 'unsigned int']
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/x86/xen/enlighten_pv.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/arch/x86/xen/enlighten_pv.c b/arch/x86/xen/enlighten_pv.c
index 1730a26ff6abc..76864ea591605 100644
--- a/arch/x86/xen/enlighten_pv.c
+++ b/arch/x86/xen/enlighten_pv.c
@@ -908,14 +908,15 @@ static u64 xen_read_msr_safe(unsigned int msr, int *err)
 static int xen_write_msr_safe(unsigned int msr, unsigned low, unsigned high)
 {
 	int ret;
+#ifdef CONFIG_X86_64
+	unsigned int which;
+	u64 base;
+#endif
 
 	ret = 0;
 
 	switch (msr) {
 #ifdef CONFIG_X86_64
-		unsigned which;
-		u64 base;
-
 	case MSR_FS_BASE:		which = SEGBASE_FS; goto set;
 	case MSR_KERNEL_GS_BASE:	which = SEGBASE_GS_USER; goto set;
 	case MSR_GS_BASE:		which = SEGBASE_GS_KERNEL; goto set;
-- 
2.20.1

[PATCH AUTOSEL 4.19 31/32] s390/qeth: vnicc Fix EOPNOTSUPP precedence

[Sasha Levin]

From: Alexandra Winter <wintera@linux.ibm.com>

[ Upstream commit 6f3846f0955308b6d1b219419da42b8de2c08845 ]

When getting or setting VNICC parameters, the error code EOPNOTSUPP
should have precedence over EBUSY.

EBUSY is used because vnicc feature and bridgeport feature are mutually
exclusive, which is a temporary condition.
Whereas EOPNOTSUPP indicates that the HW does not support all or parts of
the vnicc feature.
This issue causes the vnicc sysfs params to show 'blocked by bridgeport'
for HW that does not support VNICC at all.

Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/s390/net/qeth_l2_main.c | 29 +++++++++++++----------------
 1 file changed, 13 insertions(+), 16 deletions(-)

diff --git a/drivers/s390/net/qeth_l2_main.c b/drivers/s390/net/qeth_l2_main.c
index aa90004f49e28..eb917e93fa72f 100644
--- a/drivers/s390/net/qeth_l2_main.c
+++ b/drivers/s390/net/qeth_l2_main.c
@@ -2148,15 +2148,14 @@ int qeth_l2_vnicc_set_state(struct qeth_card *card, u32 vnicc, bool state)
 
 	QETH_CARD_TEXT(card, 2, "vniccsch");
 
-	/* do not change anything if BridgePort is enabled */
-	if (qeth_bridgeport_is_in_use(card))
-		return -EBUSY;
-
 	/* check if characteristic and enable/disable are supported */
 	if (!(card->options.vnicc.sup_chars & vnicc) ||
 	    !(card->options.vnicc.set_char_sup & vnicc))
 		return -EOPNOTSUPP;
 
+	if (qeth_bridgeport_is_in_use(card))
+		return -EBUSY;
+
 	/* set enable/disable command and store wanted characteristic */
 	if (state) {
 		cmd = IPA_VNICC_ENABLE;
@@ -2202,14 +2201,13 @@ int qeth_l2_vnicc_get_state(struct qeth_card *card, u32 vnicc, bool *state)
 
 	QETH_CARD_TEXT(card, 2, "vniccgch");
 
-	/* do not get anything if BridgePort is enabled */
-	if (qeth_bridgeport_is_in_use(card))
-		return -EBUSY;
-
 	/* check if characteristic is supported */
 	if (!(card->options.vnicc.sup_chars & vnicc))
 		return -EOPNOTSUPP;
 
+	if (qeth_bridgeport_is_in_use(card))
+		return -EBUSY;
+
 	/* if card is ready, query current VNICC state */
 	if (qeth_card_hw_is_reachable(card))
 		rc = qeth_l2_vnicc_query_chars(card);
@@ -2227,15 +2225,14 @@ int qeth_l2_vnicc_set_timeout(struct qeth_card *card, u32 timeout)
 
 	QETH_CARD_TEXT(card, 2, "vniccsto");
 
-	/* do not change anything if BridgePort is enabled */
-	if (qeth_bridgeport_is_in_use(card))
-		return -EBUSY;
-
 	/* check if characteristic and set_timeout are supported */
 	if (!(card->options.vnicc.sup_chars & QETH_VNICC_LEARNING) ||
 	    !(card->options.vnicc.getset_timeout_sup & QETH_VNICC_LEARNING))
 		return -EOPNOTSUPP;
 
+	if (qeth_bridgeport_is_in_use(card))
+		return -EBUSY;
+
 	/* do we need to do anything? */
 	if (card->options.vnicc.learning_timeout == timeout)
 		return rc;
@@ -2264,14 +2261,14 @@ int qeth_l2_vnicc_get_timeout(struct qeth_card *card, u32 *timeout)
 
 	QETH_CARD_TEXT(card, 2, "vniccgto");
 
-	/* do not get anything if BridgePort is enabled */
-	if (qeth_bridgeport_is_in_use(card))
-		return -EBUSY;
-
 	/* check if characteristic and get_timeout are supported */
 	if (!(card->options.vnicc.sup_chars & QETH_VNICC_LEARNING) ||
 	    !(card->options.vnicc.getset_timeout_sup & QETH_VNICC_LEARNING))
 		return -EOPNOTSUPP;
+
+	if (qeth_bridgeport_is_in_use(card))
+		return -EBUSY;
+
 	/* if card is ready, get timeout. Otherwise, just return stored value */
 	*timeout = card->options.vnicc.learning_timeout;
 	if (qeth_card_hw_is_reachable(card))
-- 
2.20.1

[PATCH AUTOSEL 4.19 32/32] net: thunderx: workaround BGX TX Underflow issue

[Sasha Levin]

From: Tim Harvey <tharvey@gateworks.com>

[ Upstream commit 971617c3b761c876d686a2188220a33898c90e99 ]

While it is not yet understood why a TX underflow can easily occur
for SGMII interfaces resulting in a TX wedge. It has been found that
disabling/re-enabling the LMAC resolves the issue.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Robert Jones <rjones@gateworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../net/ethernet/cavium/thunder/thunder_bgx.c | 62 ++++++++++++++++++-
 .../net/ethernet/cavium/thunder/thunder_bgx.h |  9 +++
 2 files changed, 68 insertions(+), 3 deletions(-)

diff --git a/drivers/net/ethernet/cavium/thunder/thunder_bgx.c b/drivers/net/ethernet/cavium/thunder/thunder_bgx.c
index 8ae28f82aafdc..e5fc89813852c 100644
--- a/drivers/net/ethernet/cavium/thunder/thunder_bgx.c
+++ b/drivers/net/ethernet/cavium/thunder/thunder_bgx.c
@@ -413,10 +413,19 @@ void bgx_lmac_rx_tx_enable(int node, int bgx_idx, int lmacid, bool enable)
 	lmac = &bgx->lmac[lmacid];
 
 	cfg = bgx_reg_read(bgx, lmacid, BGX_CMRX_CFG);
-	if (enable)
+	if (enable) {
 		cfg |= CMR_PKT_RX_EN | CMR_PKT_TX_EN;
-	else
+
+		/* enable TX FIFO Underflow interrupt */
+		bgx_reg_modify(bgx, lmacid, BGX_GMP_GMI_TXX_INT_ENA_W1S,
+			       GMI_TXX_INT_UNDFLW);
+	} else {
 		cfg &= ~(CMR_PKT_RX_EN | CMR_PKT_TX_EN);
+
+		/* Disable TX FIFO Underflow interrupt */
+		bgx_reg_modify(bgx, lmacid, BGX_GMP_GMI_TXX_INT_ENA_W1C,
+			       GMI_TXX_INT_UNDFLW);
+	}
 	bgx_reg_write(bgx, lmacid, BGX_CMRX_CFG, cfg);
 
 	if (bgx->is_rgx)
@@ -1544,6 +1553,48 @@ static int bgx_init_phy(struct bgx *bgx)
 	return bgx_init_of_phy(bgx);
 }
 
+static irqreturn_t bgx_intr_handler(int irq, void *data)
+{
+	struct bgx *bgx = (struct bgx *)data;
+	u64 status, val;
+	int lmac;
+
+	for (lmac = 0; lmac < bgx->lmac_count; lmac++) {
+		status = bgx_reg_read(bgx, lmac, BGX_GMP_GMI_TXX_INT);
+		if (status & GMI_TXX_INT_UNDFLW) {
+			pci_err(bgx->pdev, "BGX%d lmac%d UNDFLW\n",
+				bgx->bgx_id, lmac);
+			val = bgx_reg_read(bgx, lmac, BGX_CMRX_CFG);
+			val &= ~CMR_EN;
+			bgx_reg_write(bgx, lmac, BGX_CMRX_CFG, val);
+			val |= CMR_EN;
+			bgx_reg_write(bgx, lmac, BGX_CMRX_CFG, val);
+		}
+		/* clear interrupts */
+		bgx_reg_write(bgx, lmac, BGX_GMP_GMI_TXX_INT, status);
+	}
+
+	return IRQ_HANDLED;
+}
+
+static void bgx_register_intr(struct pci_dev *pdev)
+{
+	struct bgx *bgx = pci_get_drvdata(pdev);
+	int ret;
+
+	ret = pci_alloc_irq_vectors(pdev, BGX_LMAC_VEC_OFFSET,
+				    BGX_LMAC_VEC_OFFSET, PCI_IRQ_ALL_TYPES);
+	if (ret < 0) {
+		pci_err(pdev, "Req for #%d msix vectors failed\n",
+			BGX_LMAC_VEC_OFFSET);
+		return;
+	}
+	ret = pci_request_irq(pdev, GMPX_GMI_TX_INT, bgx_intr_handler, NULL,
+			      bgx, "BGX%d", bgx->bgx_id);
+	if (ret)
+		pci_free_irq(pdev, GMPX_GMI_TX_INT, bgx);
+}
+
 static int bgx_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 {
 	int err;
@@ -1559,7 +1610,7 @@ static int bgx_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 
 	pci_set_drvdata(pdev, bgx);
 
-	err = pci_enable_device(pdev);
+	err = pcim_enable_device(pdev);
 	if (err) {
 		dev_err(dev, "Failed to enable PCI device\n");
 		pci_set_drvdata(pdev, NULL);
@@ -1613,6 +1664,8 @@ static int bgx_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 
 	bgx_init_hw(bgx);
 
+	bgx_register_intr(pdev);
+
 	/* Enable all LMACs */
 	for (lmac = 0; lmac < bgx->lmac_count; lmac++) {
 		err = bgx_lmac_enable(bgx, lmac);
@@ -1629,6 +1682,7 @@ static int bgx_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
 
 err_enable:
 	bgx_vnic[bgx->bgx_id] = NULL;
+	pci_free_irq(pdev, GMPX_GMI_TX_INT, bgx);
 err_release_regions:
 	pci_release_regions(pdev);
 err_disable_device:
@@ -1646,6 +1700,8 @@ static void bgx_remove(struct pci_dev *pdev)
 	for (lmac = 0; lmac < bgx->lmac_count; lmac++)
 		bgx_lmac_disable(bgx, lmac);
 
+	pci_free_irq(pdev, GMPX_GMI_TX_INT, bgx);
+
 	bgx_vnic[bgx->bgx_id] = NULL;
 	pci_release_regions(pdev);
 	pci_disable_device(pdev);
diff --git a/drivers/net/ethernet/cavium/thunder/thunder_bgx.h b/drivers/net/ethernet/cavium/thunder/thunder_bgx.h
index cbdd20b9ee6f1..ac0c89cd5c3d2 100644
--- a/drivers/net/ethernet/cavium/thunder/thunder_bgx.h
+++ b/drivers/net/ethernet/cavium/thunder/thunder_bgx.h
@@ -183,6 +183,15 @@
 #define BGX_GMP_GMI_TXX_BURST		0x38228
 #define BGX_GMP_GMI_TXX_MIN_PKT		0x38240
 #define BGX_GMP_GMI_TXX_SGMII_CTL	0x38300
+#define BGX_GMP_GMI_TXX_INT		0x38500
+#define BGX_GMP_GMI_TXX_INT_W1S		0x38508
+#define BGX_GMP_GMI_TXX_INT_ENA_W1C	0x38510
+#define BGX_GMP_GMI_TXX_INT_ENA_W1S	0x38518
+#define  GMI_TXX_INT_PTP_LOST			BIT_ULL(4)
+#define  GMI_TXX_INT_LATE_COL			BIT_ULL(3)
+#define  GMI_TXX_INT_XSDEF			BIT_ULL(2)
+#define  GMI_TXX_INT_XSCOL			BIT_ULL(1)
+#define  GMI_TXX_INT_UNDFLW			BIT_ULL(0)
 
 #define BGX_MSIX_VEC_0_29_ADDR		0x400000 /* +(0..29) << 4 */
 #define BGX_MSIX_VEC_0_29_CTL		0x400008
-- 
2.20.1