[PATCH AUTOSEL 5.4 12/57] extcon: arizona: Fix some issues when HPDET IRQ fires after the jack has been unplugged

[Sasha Levin <sashal@kernel.org>]

From: Hans de Goede <hdegoede@redhat.com>

[ Upstream commit c309a3e8793f7e01c4a4ec7960658380572cb576 ]

When the jack is partially inserted and then removed again it may be
removed while the hpdet code is running. In this case the following
may happen:

1. The "JACKDET rise" or ""JACKDET fall" IRQ triggers
2. arizona_jackdet runs and takes info->lock
3. The "HPDET" IRQ triggers
4. arizona_hpdet_irq runs, blocks on info->lock
5. arizona_jackdet calls arizona_stop_mic() and clears info->hpdet_done
6. arizona_jackdet releases info->lock
7. arizona_hpdet_irq now can continue running and:
7.1 Calls arizona_start_mic() (if a mic was detected)
7.2 sets info->hpdet_done

Step 7 is undesirable / a bug:
7.1 causes the device to stay in a high power-state (with MICVDD enabled)
7.2 causes hpdet to not run on the next jack insertion, which in turn
    causes the EXTCON_JACK_HEADPHONE state to never get set

This fixes both issues by skipping these 2 steps when arizona_hpdet_irq
runs after the jack has been unplugged.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/extcon/extcon-arizona.c | 17 +++++++++--------
 1 file changed, 9 insertions(+), 8 deletions(-)

diff --git a/drivers/extcon/extcon-arizona.c b/drivers/extcon/extcon-arizona.c
index e970134c95fa..7f1cd61443ff 100644
--- a/drivers/extcon/extcon-arizona.c
+++ b/drivers/extcon/extcon-arizona.c
@@ -597,7 +597,7 @@ static irqreturn_t arizona_hpdet_irq(int irq, void *data)
 	struct arizona *arizona = info->arizona;
 	int id_gpio = arizona->pdata.hpdet_id_gpio;
 	unsigned int report = EXTCON_JACK_HEADPHONE;
-	int ret, reading;
+	int ret, reading, state;
 	bool mic = false;
 
 	mutex_lock(&info->lock);
@@ -610,12 +610,11 @@ static irqreturn_t arizona_hpdet_irq(int irq, void *data)
 	}
 
 	/* If the cable was removed while measuring ignore the result */
-	ret = extcon_get_state(info->edev, EXTCON_MECHANICAL);
-	if (ret < 0) {
-		dev_err(arizona->dev, "Failed to check cable state: %d\n",
-			ret);
+	state = extcon_get_state(info->edev, EXTCON_MECHANICAL);
+	if (state < 0) {
+		dev_err(arizona->dev, "Failed to check cable state: %d\n", state);
 		goto out;
-	} else if (!ret) {
+	} else if (!state) {
 		dev_dbg(arizona->dev, "Ignoring HPDET for removed cable\n");
 		goto done;
 	}
@@ -668,7 +667,7 @@ static irqreturn_t arizona_hpdet_irq(int irq, void *data)
 			   ARIZONA_ACCDET_MODE_MASK, ARIZONA_ACCDET_MODE_MIC);
 
 	/* If we have a mic then reenable MICDET */
-	if (mic || info->mic)
+	if (state && (mic || info->mic))
 		arizona_start_mic(info);
 
 	if (info->hpdet_active) {
@@ -676,7 +675,9 @@ static irqreturn_t arizona_hpdet_irq(int irq, void *data)
 		info->hpdet_active = false;
 	}
 
-	info->hpdet_done = true;
+	/* Do not set hp_det done when the cable has been unplugged */
+	if (state)
+		info->hpdet_done = true;
 
 out:
 	mutex_unlock(&info->lock);
-- 
2.30.2