[PATCH 4.19 02/33] bpf: Do not use ax register in interpreter on div/mod

[Greg Kroah-Hartman <gregkh@linuxfoundation.org>]

From: Daniel Borkmann <daniel@iogearbox.net>

Partially undo old commit 144cd91c4c2b ("bpf: move tmp variable into ax
register in interpreter"). The reason we need this here is because ax
register will be used for holding temporary state for div/mod instruction
which otherwise interpreter would corrupt. This will cause a small +8 byte
stack increase for interpreter, but with the gain that we can use it from
verifier rewrites as scratch register.

Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: John Fastabend <john.fastabend@gmail.com>
[cascardo: This partial revert is needed in order to support using AX for
the following two commits, as there is no JMP32 on 4.19.y]
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
 kernel/bpf/core.c |   32 +++++++++++++++-----------------
 1 file changed, 15 insertions(+), 17 deletions(-)

--- a/kernel/bpf/core.c
+++ b/kernel/bpf/core.c
@@ -705,9 +705,6 @@ static int bpf_jit_blind_insn(const stru
 	 * below.
 	 *
 	 * Constant blinding is only used by JITs, not in the interpreter.
-	 * The interpreter uses AX in some occasions as a local temporary
-	 * register e.g. in DIV or MOD instructions.
-	 *
 	 * In restricted circumstances, the verifier can also use the AX
 	 * register for rewrites as long as they do not interfere with
 	 * the above cases!
@@ -1057,6 +1054,7 @@ static u64 ___bpf_prog_run(u64 *regs, co
 #undef BPF_INSN_3_LBL
 #undef BPF_INSN_2_LBL
 	u32 tail_call_cnt = 0;
+	u64 tmp;
 
 #define CONT	 ({ insn++; goto select_insn; })
 #define CONT_JMP ({ insn++; goto select_insn; })
@@ -1117,36 +1115,36 @@ select_insn:
 		(*(s64 *) &DST) >>= IMM;
 		CONT;
 	ALU64_MOD_X:
-		div64_u64_rem(DST, SRC, &AX);
-		DST = AX;
+		div64_u64_rem(DST, SRC, &tmp);
+		DST = tmp;
 		CONT;
 	ALU_MOD_X:
-		AX = (u32) DST;
-		DST = do_div(AX, (u32) SRC);
+		tmp = (u32) DST;
+		DST = do_div(tmp, (u32) SRC);
 		CONT;
 	ALU64_MOD_K:
-		div64_u64_rem(DST, IMM, &AX);
-		DST = AX;
+		div64_u64_rem(DST, IMM, &tmp);
+		DST = tmp;
 		CONT;
 	ALU_MOD_K:
-		AX = (u32) DST;
-		DST = do_div(AX, (u32) IMM);
+		tmp = (u32) DST;
+		DST = do_div(tmp, (u32) IMM);
 		CONT;
 	ALU64_DIV_X:
 		DST = div64_u64(DST, SRC);
 		CONT;
 	ALU_DIV_X:
-		AX = (u32) DST;
-		do_div(AX, (u32) SRC);
-		DST = (u32) AX;
+		tmp = (u32) DST;
+		do_div(tmp, (u32) SRC);
+		DST = (u32) tmp;
 		CONT;
 	ALU64_DIV_K:
 		DST = div64_u64(DST, IMM);
 		CONT;
 	ALU_DIV_K:
-		AX = (u32) DST;
-		do_div(AX, (u32) IMM);
-		DST = (u32) AX;
+		tmp = (u32) DST;
+		do_div(tmp, (u32) IMM);
+		DST = (u32) tmp;
 		CONT;
 	ALU_END_TO_BE:
 		switch (IMM) {