[PATCH v2 2/6] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[PATCH v2 2/6] arm64: dts: imx8mm-kontron: Make sure SOC and DRAM supply voltages are correct

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

It looks like the voltages for the SOC and DRAM supply weren't properly
validated before. The datasheet and uboot-imx code tells us that VDD_SOC
should be 800 mV in suspend and 850 mV in run mode. VDD_DRAM should be
950 mV for DDR clock frequencies of up to 1.5 GHz.

Let's fix these values to make sure the voltages are within the required
range.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes in v2:
  * Fix the commit ref in the Fixes tag
  * Improve commit message
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index 6eacc32bc95e..4df45b5e5f6e 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -92,10 +92,12 @@ regulators {
 			reg_vdd_soc: BUCK1 {
 				regulator-name = "buck1";
 				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <900000>;
+				regulator-max-microvolt = <850000>;
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <850000>;
+				nxp,dvs-standby-voltage = <800000>;
 			};
 
 			reg_vdd_arm: BUCK2 {
@@ -112,7 +114,7 @@ reg_vdd_arm: BUCK2 {
 			reg_vdd_dram: BUCK3 {
 				regulator-name = "buck3";
 				regulator-min-microvolt = <850000>;
-				regulator-max-microvolt = <900000>;
+				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
-- 
2.33.0

[PATCH v2 3/6] arm64: dts: imx8mm-kontron: Set lower limit of VDD_SNVS to 800 mV

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

According to the datasheet the typical value for VDD_SNVS should be
800 mV, so let's make sure that this is within the range of the
regulator.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes in v2:
  * Fix the commit ref in the Fixes tag
  * Only set lower limit of regulator as upper limit matches range
    im datasheet.
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
index 4df45b5e5f6e..1a2a9110e3d1 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
@@ -153,7 +153,7 @@ reg_nvcc_snvs: LDO1 {
 
 			reg_vdd_snvs: LDO2 {
 				regulator-name = "ldo2";
-				regulator-min-microvolt = <850000>;
+				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <900000>;
 				regulator-boot-on;
 				regulator-always-on;
-- 
2.33.0

[PATCH v2 4/6] arm64: dts: imx8mm-kontron: Fix polarity of reg_rst_eth2

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The regulator reg_rst_eth2 should keep the reset signal of the USB ethernet
adapter deasserted anytime. Fix the polarity and mark it as always-on.

Anyway, using the regulator is only a workaround for the missing support of
specifying a reset GPIO for USB devices in a generic way. As we don't
have a solution for this at the moment, at least fix the current
workaround.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes in v2:
  * Fix the commit ref in the Fixes tag
  * Improve commit message
  * Remove useless change of uncontrolled reg_vdd_5v
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index 5f6fc4c2c529..a192a047f264 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -70,7 +70,9 @@ reg_rst_eth2: regulator-rst-eth2 {
 		regulator-name = "rst-usb-eth2";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_usb_eth2>;
-		gpio = <&gpio3 2 GPIO_ACTIVE_LOW>;
+		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
 	};
 
 	reg_vdd_5v: regulator-5v {
-- 
2.33.0

[PATCH v2 5/6] arm64: dts: imx8mm-kontron: Fix CAN SPI clock frequency

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

The MCP2515 can be used with an SPI clock of up to 10 MHz. Set the
limit accordingly to prevent any performance issues caused by the
really low clock speed of 100 kHz.

This removes the arbitrarily low limit on the SPI frequency, that was
caused by a typo in the original dts.

Without this change, receiving CAN messages on the board beyond a
certain bitrate will cause overrun errors (see 'ip -det -stat link show
can0').

With this fix, receiving messages on the bus works without any overrun
errors for bitrates up to 1 MBit.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes in v2:
  * Fix the commit ref in the Fixes tag
  * Improve commit message
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index a192a047f264..14263cd40daf 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -97,7 +97,7 @@ can0: can@0 {
 		clocks = <&osc_can>;
 		interrupt-parent = <&gpio4>;
 		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
-		spi-max-frequency = <100000>;
+		spi-max-frequency = <10000000>;
 		vdd-supply = <&reg_vdd_3v3>;
 		xceiver-supply = <&reg_vdd_5v>;
 	};
-- 
2.33.0

[PATCH v2 6/6] arm64: dts: imx8mm-kontron: Fix connection type for VSC8531 RGMII PHY

[Frieder Schrempf]

From: Frieder Schrempf <frieder.schrempf@kontron.de>

Previously we falsely relied on the PHY driver to unconditionally
enable the internal RX delay. Since the following fix for the PHY
driver this is not the case anymore:

commit 7b005a1742be ("net: phy: mscc: configure both RX and TX internal
delays for RGMII")

In order to enable the delay we need to set the connection type to
"rgmii-rxid". Without the RX delay the ethernet is not functional at
all.

Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
---
Changes in v2:
  * Fix the commit ref in the Fixes tag
  * Extend the commit message to make clear that ethernet is not working
    without this fix.
---
 arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
index 14263cd40daf..41ddaf980e14 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
@@ -113,7 +113,7 @@ &ecspi3 {
 &fec1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
-	phy-connection-type = "rgmii";
+	phy-connection-type = "rgmii-rxid";
 	phy-handle = <&ethphy>;
 	status = "okay";
 
-- 
2.33.0