From: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To: stable@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
patches@lists.linux.dev, Hongyu Xie <xiehongyu1@kylinos.cn>,
stable <stable@kernel.org>
Subject: [PATCH 6.14 11/24] usb: storage: Ignore UAS driver for SanDisk 3.2 Gen2 storage device
Date: Sat, 7 Jun 2025 12:07:51 +0200 [thread overview]
Message-ID: <20250607100718.147979542@linuxfoundation.org> (raw)
In-Reply-To: <20250607100717.706871523@linuxfoundation.org>
6.14-stable review patch. If anyone has any objections, please let me know.
------------------
From: Hongyu Xie <xiehongyu1@kylinos.cn>
commit a541acceedf4f639f928f41fbb676b75946dc295 upstream.
SanDisk 3.2 Gen2 storage device(0781:55e8) doesn't work well with UAS.
Log says,
[ 6.507865][ 3] [ T159] usb 2-1.4: new SuperSpeed Gen 1 USB device number 4 using xhci_hcd
[ 6.540314][ 3] [ T159] usb 2-1.4: New USB device found, idVendor=0781, idProduct=55e8, bcdDevice= 0.01
[ 6.576304][ 3] [ T159] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.584727][ 3] [ T159] usb 2-1.4: Product: SanDisk 3.2 Gen2
[ 6.590459][ 3] [ T159] usb 2-1.4: Manufacturer: SanDisk
[ 6.595845][ 3] [ T159] usb 2-1.4: SerialNumber: 03021707022525140940
[ 7.230852][ 0] [ T265] usbcore: registered new interface driver usb-storage
[ 7.251247][ 0] [ T265] scsi host3: uas
[ 7.255280][ 0] [ T265] usbcore: registered new interface driver uas
[ 7.270498][ 1] [ T192] scsi 3:0:0:0: Direct-Access SanDisk Extreme Pro DDE1 0110 PQ: 0 ANSI: 6
[ 7.299588][ 3] [ T192] scsi 3:0:0:1: Enclosure SanDisk SES Device 0110 PQ: 0 ANSI: 6
[ 7.321681][ 3] [ T192] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 7.328185][ 3] [ T192] scsi 3:0:0:1: Attached scsi generic sg2 type 13
[ 7.328804][ 0] [ T191] sd 3:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB)
[ 7.343486][ 0] [ T191] sd 3:0:0:0: [sda] 4096-byte physical blocks
[ 7.364611][ 0] [ T191] sd 3:0:0:0: [sda] Write Protect is off
[ 7.370524][ 0] [ T191] sd 3:0:0:0: [sda] Mode Sense: 3d 00 10 00
[ 7.390655][ 0] [ T191] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 7.401363][ 0] [ T191] sd 3:0:0:0: [sda] Optimal transfer size 1048576 bytes
[ 7.436010][ 0] [ T191] sda: sda1
[ 7.450850][ 0] [ T191] sd 3:0:0:0: [sda] Attached SCSI disk
[ 7.470218][ 4] [ T262] scsi 3:0:0:1: Failed to get diagnostic page 0x1
[ 7.474869][ 0] [ C0] sd 3:0:0:0: [sda] tag#0 data cmplt err -75 uas-tag 2 inflight: CMD
[ 7.476911][ 4] [ T262] scsi 3:0:0:1: Failed to bind enclosure -19
[ 7.485330][ 0] [ C0] sd 3:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 00 00 28 00 00 10 00
[ 7.491593][ 4] [ T262] ses 3:0:0:1: Attached Enclosure device
[ 38.066980][ 4] [ T192] sd 3:0:0:0: [sda] tag#4 uas_eh_abort_handler 0 uas-tag 5 inflight: CMD IN
[ 38.076012][ 4] [ T192] sd 3:0:0:0: [sda] tag#4 CDB: Read(10) 28 00 00 00 01 08 00 00 f8 00
[ 38.086485][ 4] [ T192] sd 3:0:0:0: [sda] tag#3 uas_eh_abort_handler 0 uas-tag 1 inflight: CMD IN
[ 38.095515][ 4] [ T192] sd 3:0:0:0: [sda] tag#3 CDB: Read(10) 28 00 00 00 00 10 00 00 08 00
[ 38.104122][ 4] [ T192] sd 3:0:0:0: [sda] tag#2 uas_eh_abort_handler 0 uas-tag 4 inflight: CMD IN
[ 38.113152][ 4] [ T192] sd 3:0:0:0: [sda] tag#2 CDB: Read(10) 28 00 00 00 00 88 00 00 78 00
[ 38.121761][ 4] [ T192] sd 3:0:0:0: [sda] tag#1 uas_eh_abort_handler 0 uas-tag 3 inflight: CMD IN
[ 38.130791][ 4] [ T192] sd 3:0:0:0: [sda] tag#1 CDB: Read(10) 28 00 00 00 00 48 00 00 30 00
[ 38.139401][ 4] [ T192] sd 3:0:0:0: [sda] tag#0 uas_eh_abort_handler 0 uas-tag 2 inflight: CMD
[ 38.148170][ 4] [ T192] sd 3:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 00 00 28 00 00 10 00
[ 38.178980][ 2] [ T304] scsi host3: uas_eh_device_reset_handler start
[ 38.901540][ 2] [ T304] usb 2-1.4: reset SuperSpeed Gen 1 USB device number 4 using xhci_hcd
[ 38.936791][ 2] [ T304] scsi host3: uas_eh_device_reset_handler success
Device decriptor is below,
Bus 002 Device 006: ID 0781:55e8 SanDisk Corp. SanDisk 3.2 Gen2
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 3.20
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 9
idVendor 0x0781 SanDisk Corp.
idProduct 0x55e8
bcdDevice 0.01
iManufacturer 1 SanDisk
iProduct 2 SanDisk 3.2 Gen2
iSerial 3 03021707022525140940
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0079
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 896mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk-Only
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 1
bNumEndpoints 4
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 98
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x01 EP 1 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 0
Command pipe (0x01)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
MaxStreams 32
Status pipe (0x02)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
MaxStreams 32
Data-in pipe (0x03)
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0400 1x 1024 bytes
bInterval 0
bMaxBurst 15
MaxStreams 32
Data-out pipe (0x04)
Binary Object Store Descriptor:
bLength 5
bDescriptorType 15
wTotalLength 0x002a
bNumDeviceCaps 3
USB 2.0 Extension Device Capability:
bLength 7
bDescriptorType 16
bDevCapabilityType 2
bmAttributes 0x0000f41e
BESL Link Power Management (LPM) Supported
BESL value 1024 us
Deep BESL value 61440 us
SuperSpeed USB Device Capability:
bLength 10
bDescriptorType 16
bDevCapabilityType 3
bmAttributes 0x00
wSpeedsSupported 0x000e
Device can operate at Full Speed (12Mbps)
Device can operate at High Speed (480Mbps)
Device can operate at SuperSpeed (5Gbps)
bFunctionalitySupport 1
Lowest fully-functional device speed is Full Speed (12Mbps)
bU1DevExitLat 10 micro seconds
bU2DevExitLat 2047 micro seconds
SuperSpeedPlus USB Device Capability:
bLength 20
bDescriptorType 16
bDevCapabilityType 10
bmAttributes 0x00000001
Sublink Speed Attribute count 1
Sublink Speed ID count 0
wFunctionalitySupport 0x1100
bmSublinkSpeedAttr[0] 0x000a4030
Speed Attribute ID: 0 10Gb/s Symmetric RX SuperSpeedPlus
bmSublinkSpeedAttr[1] 0x000a40b0
Speed Attribute ID: 0 10Gb/s Symmetric TX SuperSpeedPlus
Device Status: 0x0000
(Bus Powered)
So ignore UAS driver for this device.
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Cc: stable <stable@kernel.org>
Link: https://lore.kernel.org/r/20250519023328.1498856-1-xiehongyu1@kylinos.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
---
drivers/usb/storage/unusual_uas.h | 7 +++++++
1 file changed, 7 insertions(+)
--- a/drivers/usb/storage/unusual_uas.h
+++ b/drivers/usb/storage/unusual_uas.h
@@ -52,6 +52,13 @@ UNUSUAL_DEV(0x059f, 0x1061, 0x0000, 0x99
USB_SC_DEVICE, USB_PR_DEVICE, NULL,
US_FL_NO_REPORT_OPCODES | US_FL_NO_SAME),
+/* Reported-by: Zhihong Zhou <zhouzhihong@greatwall.com.cn> */
+UNUSUAL_DEV(0x0781, 0x55e8, 0x0000, 0x9999,
+ "SanDisk",
+ "",
+ USB_SC_DEVICE, USB_PR_DEVICE, NULL,
+ US_FL_IGNORE_UAS),
+
/* Reported-by: Hongling Zeng <zenghongling@kylinos.cn> */
UNUSUAL_DEV(0x090c, 0x2000, 0x0000, 0x9999,
"Hiksemi",
next prev parent reply other threads:[~2025-06-07 10:10 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-06-07 10:07 [PATCH 6.14 00/24] 6.14.11-rc1 review Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 01/24] tracing: Fix compilation warning on arm32 Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 02/24] pinctrl: armada-37xx: use correct OUTPUT_VAL register for GPIOs > 31 Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 03/24] pinctrl: armada-37xx: set GPIO output value before setting direction Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 04/24] clk: samsung: correct clock summary for hsi1 block Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 05/24] acpi-cpufreq: Fix nominal_freq units to KHz in get_max_boost_ratio() Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 06/24] Documentation: ACPI: Use all-string data node references Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 07/24] rtc: Make rtc_time64_to_tm() support dates before 1970 Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 08/24] rtc: Fix offset calculation for .start_secs < 0 Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 09/24] orangefs: adjust counting code to recover from 665575cf Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 10/24] usb: quirks: Add NO_LPM quirk for SanDisk Extreme 55AE Greg Kroah-Hartman
2025-06-07 10:07 ` Greg Kroah-Hartman [this message]
2025-06-07 10:07 ` [PATCH 6.14 12/24] USB: serial: pl2303: add new chip PL2303GC-Q20 and PL2303GT-2AB Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 13/24] usb: typec: ucsi: fix Clang -Wsign-conversion warning Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 14/24] Bluetooth: hci_qca: move the SoC type check to the right place Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 15/24] serial: jsm: fix NPE during jsm_uart_port_init Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 16/24] nvmem: rmem: select CONFIG_CRC32 Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 17/24] usb: usbtmc: Fix timeout value in get_stb Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 18/24] binder: fix use-after-free in binderfs_evict_inode() Greg Kroah-Hartman
2025-06-07 10:07 ` [PATCH 6.14 19/24] binder: fix yet another UAF in binder_devices Greg Kroah-Hartman
2025-06-07 10:08 ` [PATCH 6.14 20/24] thunderbolt: Do not double dequeue a configuration request Greg Kroah-Hartman
2025-06-07 10:08 ` [PATCH 6.14 21/24] dt-bindings: pwm: adi,axi-pwmgen: Fix clocks Greg Kroah-Hartman
2025-06-07 10:08 ` [PATCH 6.14 22/24] dt-bindings: usb: cypress,hx3: Add support for all variants Greg Kroah-Hartman
2025-06-07 10:08 ` [PATCH 6.14 23/24] dt-bindings: phy: imx8mq-usb: fix fsl,phy-tx-vboost-level-microvolt property Greg Kroah-Hartman
2025-06-07 10:08 ` [PATCH 6.14 24/24] Revert "drm/amd/display: more liberal vmin/vmax update for freesync" Greg Kroah-Hartman
2025-06-07 16:22 ` [PATCH 6.14 00/24] 6.14.11-rc1 review Florian Fainelli
2025-06-08 5:44 ` Ron Economos
2025-06-08 6:44 ` Naresh Kamboju
2025-06-08 17:00 ` Peter Schneider
2025-06-08 17:54 ` Pavel Machek
2025-06-08 22:22 ` Mark Brown
2025-06-09 12:50 ` Jon Hunter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250607100718.147979542@linuxfoundation.org \
--to=gregkh@linuxfoundation.org \
--cc=patches@lists.linux.dev \
--cc=stable@kernel.org \
--cc=stable@vger.kernel.org \
--cc=xiehongyu1@kylinos.cn \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox