FAILED: patch "[PATCH] mtd: rawnand: qcom: Fix last codeword read in" failed to apply to 6.12-stable tree

FAILED: patch "[PATCH] mtd: rawnand: qcom: Fix last codeword read in" failed to apply to 6.12-stable tree

[gregkh]

The patch below does not apply to the 6.12-stable tree.
If someone wants it applied there, or to any other stable or longterm
tree, then please email the backport, including the original git commit
id to <stable@vger.kernel.org>.

To reproduce the conflict and resubmit, you may use the following commands:

git fetch https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/ linux-6.12.y
git checkout FETCH_HEAD
git cherry-pick -x 47bddabbf69da50999ec68be92b58356c687e1d6
# <resolve conflicts, build, test, etc.>
git commit -s
git send-email --to '<stable@vger.kernel.org>' --in-reply-to '2025062002-disperser-removing-78fc@gregkh' --subject-prefix 'PATCH 6.12.y' HEAD^..

Possible dependencies:



thanks,

greg k-h

------------------ original commit in Linus's tree ------------------

From 47bddabbf69da50999ec68be92b58356c687e1d6 Mon Sep 17 00:00:00 2001
From: Md Sadre Alam <quic_mdalam@quicinc.com>
Date: Thu, 10 Apr 2025 15:30:18 +0530
Subject: [PATCH] mtd: rawnand: qcom: Fix last codeword read in
 qcom_param_page_type_exec()

For QPIC V2 onwards there is a separate register to read
last code word "QPIC_NAND_READ_LOCATION_LAST_CW_n".

qcom_param_page_type_exec() is used to read only one code word
If it configures the number of code words to 1 in QPIC_NAND_DEV0_CFG0
register then QPIC controller thinks its reading the last code word,
since we are having separate register to read the last code word,
we have to configure "QPIC_NAND_READ_LOCATION_LAST_CW_n" register
to fetch data from QPIC buffer to system memory.

Without this change page read was failing with timeout error

/ # hexdump -C /dev/mtd1
[  129.206113] qcom-nandc 1cc8000.nand-controller: failure to read page/oob
hexdump: /dev/mtd1: Connection timed out

This issue only seen on SDX targets since SDX target used QPICv2. But
same working on IPQ targets since IPQ used QPICv1.

Cc: stable@vger.kernel.org
Fixes: 89550beb098e ("mtd: rawnand: qcom: Implement exec_op()")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
index ef2dd158ca34..a73bb154353f 100644
--- a/drivers/mtd/nand/raw/qcom_nandc.c
+++ b/drivers/mtd/nand/raw/qcom_nandc.c
@@ -1863,7 +1863,12 @@ static int qcom_param_page_type_exec(struct nand_chip *chip,  const struct nand_
 	const struct nand_op_instr *instr = NULL;
 	unsigned int op_id = 0;
 	unsigned int len = 0;
-	int ret;
+	int ret, reg_base;
+
+	reg_base = NAND_READ_LOCATION_0;
+
+	if (nandc->props->qpic_version2)
+		reg_base = NAND_READ_LOCATION_LAST_CW_0;
 
 	ret = qcom_parse_instructions(chip, subop, &q_op);
 	if (ret)
@@ -1915,7 +1920,10 @@ static int qcom_param_page_type_exec(struct nand_chip *chip,  const struct nand_
 	op_id = q_op.data_instr_idx;
 	len = nand_subop_get_data_len(subop, op_id);
 
-	nandc_set_read_loc(chip, 0, 0, 0, len, 1);
+	if (nandc->props->qpic_version2)
+		nandc_set_read_loc_last(chip, reg_base, 0, len, 1);
+	else
+		nandc_set_read_loc_first(chip, reg_base, 0, len, 1);
 
 	if (!nandc->props->qpic_version2) {
 		qcom_write_reg_dma(nandc, &nandc->regs->vld, NAND_DEV_CMD_VLD, 1, 0);

[PATCH 6.12.y] mtd: rawnand: qcom: Fix last codeword read in qcom_param_page_type_exec()

[Sasha Levin]

From: Md Sadre Alam <quic_mdalam@quicinc.com>

[ Upstream commit 47bddabbf69da50999ec68be92b58356c687e1d6 ]

For QPIC V2 onwards there is a separate register to read
last code word "QPIC_NAND_READ_LOCATION_LAST_CW_n".

qcom_param_page_type_exec() is used to read only one code word
If it configures the number of code words to 1 in QPIC_NAND_DEV0_CFG0
register then QPIC controller thinks its reading the last code word,
since we are having separate register to read the last code word,
we have to configure "QPIC_NAND_READ_LOCATION_LAST_CW_n" register
to fetch data from QPIC buffer to system memory.

Without this change page read was failing with timeout error

/ # hexdump -C /dev/mtd1
[  129.206113] qcom-nandc 1cc8000.nand-controller: failure to read page/oob
hexdump: /dev/mtd1: Connection timed out

This issue only seen on SDX targets since SDX target used QPICv2. But
same working on IPQ targets since IPQ used QPICv1.

Cc: stable@vger.kernel.org
Fixes: 89550beb098e ("mtd: rawnand: qcom: Implement exec_op()")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Tested-by: Lakshmi Sowjanya D <quic_laksd@quicinc.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/mtd/nand/raw/qcom_nandc.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
index beafca6ba0df4..275d34119acdc 100644
--- a/drivers/mtd/nand/raw/qcom_nandc.c
+++ b/drivers/mtd/nand/raw/qcom_nandc.c
@@ -2858,7 +2858,12 @@ static int qcom_param_page_type_exec(struct nand_chip *chip,  const struct nand_
 	const struct nand_op_instr *instr = NULL;
 	unsigned int op_id = 0;
 	unsigned int len = 0;
-	int ret;
+	int ret, reg_base;
+
+	reg_base = NAND_READ_LOCATION_0;
+
+	if (nandc->props->qpic_v2)
+		reg_base = NAND_READ_LOCATION_LAST_CW_0;
 
 	ret = qcom_parse_instructions(chip, subop, &q_op);
 	if (ret)
@@ -2910,7 +2915,10 @@ static int qcom_param_page_type_exec(struct nand_chip *chip,  const struct nand_
 	op_id = q_op.data_instr_idx;
 	len = nand_subop_get_data_len(subop, op_id);
 
-	nandc_set_read_loc(chip, 0, 0, 0, len, 1);
+	if (nandc->props->qpic_v2)
+		nandc_set_read_loc_last(chip, reg_base, 0, len, 1);
+	else
+		nandc_set_read_loc_first(chip, reg_base, 0, len, 1);
 
 	if (!nandc->props->qpic_v2) {
 		write_reg_dma(nandc, NAND_DEV_CMD_VLD, 1, 0);
-- 
2.39.5