From: Imre Deak <imre.deak@intel.com>
To: <intel-gfx@lists.freedesktop.org>, <intel-xe@lists.freedesktop.org>
Cc: Jani Nikula <jani.nikula@intel.com>, <stable@vger.kernel.org>,
"Charlton Lin" <charlton.lin@intel.com>,
Khaled Almahallawy <khaled.almahallawy@intel.com>,
Mika Kahola <mika.kahola@intel.com>,
"Luca Coelho" <luciano.coelho@intel.com>
Subject: [CI 1/5] drm/i915/lnl+/tc: Fix handling of an enabled/disconnected dp-alt sink
Date: Mon, 11 Aug 2025 11:01:48 +0300 [thread overview]
Message-ID: <20250811080152.906216-2-imre.deak@intel.com> (raw)
In-Reply-To: <20250811080152.906216-1-imre.deak@intel.com>
The TypeC PHY HW readout during driver loading and system resume
determines which TypeC mode the PHY is in (legacy/DP-alt/TBT-alt) and
whether the PHY is connected, based on the PHY's Owned and Ready flags.
For the PHY to be in DP-alt or legacy mode and for the PHY to be in the
connected state in these modes, both the Owned (set by the BIOS/driver)
and the Ready (set by the HW) flags should be set.
On ICL-MTL the HW kept the PHY's Ready flag set after the driver
connected the PHY by acquiring the PHY ownership (by setting the Owned
flag), until the driver disconnected the PHY by releasing the PHY
ownership (by clearing the Owned flag). On LNL+ this has changed, in
that the HW clears the Ready flag as soon as the sink gets disconnected,
even if the PHY ownership was acquired already and hence the PHY is
being used by the display.
When inheriting the HW state from BIOS for a PHY connected in DP-alt
mode on which the sink got disconnected - i.e. in a case where the sink
was connected while BIOS/GOP was running and so the sink got enabled
connecting the PHY, but the user disconnected the sink by the time the
driver loaded - the PHY Owned but not Ready state must be accounted for
on LNL+ according to the above. Do that by assuming on LNL+ that the PHY
is connected in DP-alt mode whenever the PHY Owned flag is set,
regardless of the PHY Ready flag.
This fixes a problem on LNL+, where the PHY TypeC mode / connected state
was detected incorrectly for a DP-alt sink, which got connected and then
disconnected by the user in the above way.
v2: Rename tc_phy_in_legacy_or_dp_alt_mode() to tc_phy_owned_by_display().
(Luca, Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # v6.8+
Reported-by: Charlton Lin <charlton.lin@intel.com>
Tested-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
---
drivers/gpu/drm/i915/display/intel_tc.c | 16 ++++++++++------
1 file changed, 10 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/i915/display/intel_tc.c b/drivers/gpu/drm/i915/display/intel_tc.c
index 3bc57579fe53e..d8247d1a8319b 100644
--- a/drivers/gpu/drm/i915/display/intel_tc.c
+++ b/drivers/gpu/drm/i915/display/intel_tc.c
@@ -1226,14 +1226,18 @@ static void tc_phy_get_hw_state(struct intel_tc_port *tc)
tc->phy_ops->get_hw_state(tc);
}
-static bool tc_phy_is_ready_and_owned(struct intel_tc_port *tc,
- bool phy_is_ready, bool phy_is_owned)
+static bool tc_phy_owned_by_display(struct intel_tc_port *tc,
+ bool phy_is_ready, bool phy_is_owned)
{
struct intel_display *display = to_intel_display(tc->dig_port);
- drm_WARN_ON(display->drm, phy_is_owned && !phy_is_ready);
+ if (DISPLAY_VER(display) < 20) {
+ drm_WARN_ON(display->drm, phy_is_owned && !phy_is_ready);
- return phy_is_ready && phy_is_owned;
+ return phy_is_ready && phy_is_owned;
+ } else {
+ return phy_is_owned;
+ }
}
static bool tc_phy_is_connected(struct intel_tc_port *tc,
@@ -1244,7 +1248,7 @@ static bool tc_phy_is_connected(struct intel_tc_port *tc,
bool phy_is_owned = tc_phy_is_owned(tc);
bool is_connected;
- if (tc_phy_is_ready_and_owned(tc, phy_is_ready, phy_is_owned))
+ if (tc_phy_owned_by_display(tc, phy_is_ready, phy_is_owned))
is_connected = port_pll_type == ICL_PORT_DPLL_MG_PHY;
else
is_connected = port_pll_type == ICL_PORT_DPLL_DEFAULT;
@@ -1352,7 +1356,7 @@ tc_phy_get_current_mode(struct intel_tc_port *tc)
phy_is_ready = tc_phy_is_ready(tc);
phy_is_owned = tc_phy_is_owned(tc);
- if (!tc_phy_is_ready_and_owned(tc, phy_is_ready, phy_is_owned)) {
+ if (!tc_phy_owned_by_display(tc, phy_is_ready, phy_is_owned)) {
mode = get_tc_mode_in_phy_not_owned_state(tc, live_mode);
} else {
drm_WARN_ON(display->drm, live_mode == TC_PORT_TBT_ALT);
--
2.49.1
next parent reply other threads:[~2025-08-11 8:02 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20250811080152.906216-1-imre.deak@intel.com>
2025-08-11 8:01 ` Imre Deak [this message]
2025-08-11 8:01 ` [CI 2/5] drm/i915/icl+/tc: Cache the max lane count value Imre Deak
2025-08-11 8:01 ` [CI 3/5] drm/i915/lnl+/tc: Fix max lane count HW readout Imre Deak
2025-08-11 8:01 ` [CI 4/5] drm/i915/lnl+/tc: Use the cached max lane count value Imre Deak
2025-08-11 8:01 ` [CI 5/5] drm/i915/icl+/tc: Convert AUX powered WARN to a debug message Imre Deak
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250811080152.906216-2-imre.deak@intel.com \
--to=imre.deak@intel.com \
--cc=charlton.lin@intel.com \
--cc=intel-gfx@lists.freedesktop.org \
--cc=intel-xe@lists.freedesktop.org \
--cc=jani.nikula@intel.com \
--cc=khaled.almahallawy@intel.com \
--cc=luciano.coelho@intel.com \
--cc=mika.kahola@intel.com \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox