[PATCH 2/2] mtd: spi-nor: core: avoid odd length/address writes in 8D-8D-8D mode

[liyin.zhang.cn@windriver.com]

From: Pratyush Yadav <p.yadav@ti.com>

[ Upstream commit 17926cd770ec837ed27d9856cf07f2da8dda4131 ]

On Octal DTR capable flashes like Micron Xcella the writes cannot start
or end at an odd address in Octal DTR mode. Extra 0xff bytes need to be
appended or prepended to make sure the start address and end address are
even. 0xff is used because on NOR flashes a program operation can only
flip bits from 1 to 0, not the other way round. 0 to 1 flip needs to
happen via erases.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Luke Wang <ziniu.wang_1@nxp.com>
Signed-off-by: Pratyush Yadav <pratyush@kernel.org>
Link: https://lore.kernel.org/r/20250708091646.292-2-ziniu.wang_1@nxp.com
Signed-off-by: Liyin Zhang <liyin.zhang.cn@windriver.com>
---
 drivers/mtd/spi-nor/core.c | 69 +++++++++++++++++++++++++++++++++++++-
 1 file changed, 68 insertions(+), 1 deletion(-)

diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index 9937cf3d59a4..6e135581ec62 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -2198,6 +2198,68 @@ static int spi_nor_read(struct mtd_info *mtd, loff_t from, size_t len,
 	return ret;
 }
 
+/*
+ * On Octal DTR capable flashes, writes cannot start or end at an odd address
+ * in Octal DTR mode. Extra 0xff bytes need to be appended or prepended to
+ * make sure the start address and end address are even. 0xff is used because
+ * on NOR flashes a program operation can only flip bits from 1 to 0, not the
+ * other way round. 0 to 1 flip needs to happen via erases.
+ */
+static int spi_nor_octal_dtr_write(struct spi_nor *nor, loff_t to, size_t len,
+				   const u8 *buf)
+{
+	u8 *tmp_buf;
+	size_t bytes_written;
+	loff_t start, end;
+	int ret;
+
+	if (IS_ALIGNED(to, 2) && IS_ALIGNED(len, 2))
+		return spi_nor_write_data(nor, to, len, buf);
+
+	tmp_buf = kmalloc(nor->params->page_size, GFP_KERNEL);
+	if (!tmp_buf)
+		return -ENOMEM;
+
+	memset(tmp_buf, 0xff, nor->params->page_size);
+
+	start = round_down(to, 2);
+	end = round_up(to + len, 2);
+
+	memcpy(tmp_buf + (to - start), buf, len);
+
+	ret = spi_nor_write_data(nor, start, end - start, tmp_buf);
+	if (ret == 0) {
+		ret = -EIO;
+		goto out;
+	}
+	if (ret < 0)
+		goto out;
+
+	/*
+	 * More bytes are written than actually requested, but that number can't
+	 * be reported to the calling function or it will confuse its
+	 * calculations. Calculate how many of the _requested_ bytes were
+	 * written.
+	 */
+	bytes_written = ret;
+
+	if (to != start)
+		ret -= to - start;
+
+	/*
+	 * Only account for extra bytes at the end if they were actually
+	 * written. For example, if for some reason the controller could only
+	 * complete a partial write then the adjustment for the extra bytes at
+	 * the end is not needed.
+	 */
+	if (start + bytes_written == end)
+		ret -= end - (to + len);
+
+out:
+	kfree(tmp_buf);
+	return ret;
+}
+
 /*
  * Write an address range to the nor chip.  Data must be written in
  * FLASH_PAGESIZE chunks.  The address range may be any size provided
@@ -2248,7 +2310,12 @@ static int spi_nor_write(struct mtd_info *mtd, loff_t to, size_t len,
 			goto write_err;
 		}
 
-		ret = spi_nor_write_data(nor, addr, page_remain, buf + i);
+		if (nor->write_proto == SNOR_PROTO_8_8_8_DTR)
+			ret = spi_nor_octal_dtr_write(nor, addr, page_remain,
+						      buf + i);
+		else
+			ret = spi_nor_write_data(nor, addr, page_remain,
+						 buf + i);
 		spi_nor_unlock_device(nor);
 		if (ret < 0)
 			goto write_err;
-- 
2.34.1