From: Lee Jones <lee@kernel.org>
To: lee@kernel.org, "Mark Brown" <broonie@kernel.org>,
"Foon Tan" <lftan@altera.com>,
"Graham Moore" <grmoore@opensource.altera.com>,
"Murugan R" <vadivel.muruganx.ramuthevar@intel.com>,
"Vignesh Raghavendra" <vigneshr@ti.com>,
"Pratyush Yadav" <p.yadav@ti.com>,
"Théo Lebrun" <theo.lebrun@bootlin.com>,
"Dhruva Gole" <d-gole@ti.com>,
linux-spi@vger.kernel.org, linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org
Subject: [PATCH 06/10] spi: cadence-quadspi: Bound chip select against f_pdata array size
Date: Thu, 19 Nov 2026 09:17:18 +0000 [thread overview]
Message-ID: <20261119091810.3440619-7-lee@kernel.org> (raw)
In-Reply-To: <20261119091810.3440619-1-lee@kernel.org>
cqspi_setup_flash() uses the chip select taken from each flash child
node's reg property to index the fixed-size cqspi->f_pdata[] array,
which has CQSPI_MAX_CHIPSELECT entries.
The range check now compares the chip select against num_chipselect,
which comes straight from the num-cs property and is never clamped to
CQSPI_MAX_CHIPSELECT. A device tree which specifies num-cs greater than
CQSPI_MAX_CHIPSELECT together with a flash node at a correspondingly
high reg value therefore causes writes beyond the end of f_pdata[].
Reject chip selects which do not fit in f_pdata[] as well as those which
exceed num-cs. While at it, store the chip select in a u32, matching
of_property_read_u32(), so that values with the top bit set cannot
become negative and slip past the bounds checks.
Fixes: 0d62c64a8e48 ("spi: cadence-qspi: assert each subnode flash CS is valid")
Closes: https://sashiko.dev/#/bug/linux-cd463fc8-1b94-4bcf-8d06-fae21b88894c
Cc: stable@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
---
drivers/spi/spi-cadence-quadspi.c | 8 +++++---
1 file changed, 5 insertions(+), 3 deletions(-)
diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
index 844df97111d7..fbb917c104b0 100644
--- a/drivers/spi/spi-cadence-quadspi.c
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -1751,7 +1751,8 @@ static int cqspi_setup_flash(struct cqspi_st *cqspi)
struct platform_device *pdev = cqspi->pdev;
struct device *dev = &pdev->dev;
struct cqspi_flash_pdata *f_pdata;
- int ret, cs, max_cs = -1;
+ int ret, max_cs = -1;
+ u32 cs;
/* Get flash device data */
for_each_available_child_of_node_scoped(dev->of_node, np) {
@@ -1761,8 +1762,9 @@ static int cqspi_setup_flash(struct cqspi_st *cqspi)
return ret;
}
- if (cs >= cqspi->num_chipselect) {
- dev_err(dev, "Chip select %d out of range.\n", cs);
+ if (cs >= cqspi->num_chipselect ||
+ cs >= CQSPI_MAX_CHIPSELECT) {
+ dev_err(dev, "Chip select %u out of range.\n", cs);
return -EINVAL;
}
--
2.56.1.708.g77570a6a1d-goog
next prev parent reply other threads:[~2026-11-19 9:19 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20261119091810.3440619-1-lee@kernel.org>
2026-11-19 9:17 ` [PATCH 01/10] spi: fsl-cpm: Map the zero page's address, not its struct page Lee Jones
2026-11-19 9:17 ` [PATCH 02/10] spi: bcm2835: Store native chip-select GPIO descriptor per device Lee Jones
2026-11-19 9:17 ` [PATCH 03/10] spi: ch341: Limit transfers to the hardware packet size Lee Jones
2026-11-19 9:17 ` [PATCH 04/10] spi: sprd-adi: Do not copy uninitialised data to rx_buf on read failure Lee Jones
2026-11-19 9:17 ` [PATCH 05/10] spi: topcliff-pch: Advance tx_buf between DMA chunks Lee Jones
2026-11-19 9:17 ` Lee Jones [this message]
2026-11-19 10:15 ` [PATCH 06/10] spi: cadence-quadspi: Bound chip select against f_pdata array size Théo Lebrun
2026-11-19 9:17 ` [PATCH 08/10] spi: fsl-qspi: Propagate clock errors from fsl_qspi_select_mem() Lee Jones
2026-11-19 9:17 ` [PATCH 09/10] spi: cadence-xspi: Advance tx pointer between Marvell b0 chunks Lee Jones
2026-11-19 9:17 ` [PATCH 10/10] spi: cadence-xspi: Skip tail read for qword-aligned Marvell b0 receives Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261119091810.3440619-7-lee@kernel.org \
--to=lee@kernel.org \
--cc=broonie@kernel.org \
--cc=d-gole@ti.com \
--cc=grmoore@opensource.altera.com \
--cc=lftan@altera.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=p.yadav@ti.com \
--cc=stable@vger.kernel.org \
--cc=theo.lebrun@bootlin.com \
--cc=vadivel.muruganx.ramuthevar@intel.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox