From: Zhao Li <enderaoelyther@gmail.com>
To: Ping-Ke Shih <pkshih@realtek.com>
Cc: Hemanth Selam <hemanth.selam@gmail.com>,
Morning Star <alexbestoso@gmail.com>,
linux-wireless@vger.kernel.org, linux-kernel@vger.kernel.org,
stable@vger.kernel.org, Zhao Li <enderaoelyther@gmail.com>
Subject: [PATCH rtw-next 1/3] wifi: rtlwifi: rtl8192ce: don't mark unencrypted frames as decrypted
Date: Sun, 22 Nov 2026 00:35:45 +0800 [thread overview]
Message-ID: <20261121163547.37019-2-enderaoelyther@gmail.com> (raw)
In-Reply-To: <20261121163547.37019-1-enderaoelyther@gmail.com>
The receive descriptor's SWDEC bit is set when a frame still needs
software decryption. It is also clear for a frame that was never
encrypted. rtl92ce_rx_query_desc() nevertheless sets RX_FLAG_DECRYPTED
for every frame with SWDEC clear except a protected robust management
frame, including unprotected data and management frames.
mac80211 then accepts an unprotected unicast data frame although a
pairwise key is installed, because ieee80211_drop_unencrypted() passes
frames marked as decrypted, and it accepts unprotected deauthentication
and disassociation frames on a connection that uses management frame
protection. A station in radio range can therefore inject plaintext
data into an encrypted connection, or end a protected one, by spoofing
the peer's address.
Set the flag only for a protected frame that is not a robust management
frame, as the rtl8188ee, rtl8192ee, rtl8723ae, rtl8723be and rtl8821ae
drivers do. rtw88 dropped the same assumption in commit 0649ff58a0f6
("rtw88: Don't set RX_FLAG_DECRYPTED if packet has no encryption").
Found by code review. Compile-tested with W=1.
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Cc: stable@vger.kernel.org
Signed-off-by: Zhao Li <enderaoelyther@gmail.com>
---
No new W=1, sparse or smatch warnings.
834fc28d7880 (7.4-rc1) fixed "managment" in the comment this patch removes;
with the old spelling in the removed lines it applies to 5.10.y through 7.3.y.
AI assistance was used.
.../wireless/realtek/rtlwifi/rtl8192ce/trx.c | 17 +++++------------
1 file changed, 5 insertions(+), 12 deletions(-)
diff --git a/drivers/net/wireless/realtek/rtlwifi/rtl8192ce/trx.c b/drivers/net/wireless/realtek/rtlwifi/rtl8192ce/trx.c
index 99472053ccff..3d11ddf86136 100644
--- a/drivers/net/wireless/realtek/rtlwifi/rtl8192ce/trx.c
+++ b/drivers/net/wireless/realtek/rtlwifi/rtl8192ce/trx.c
@@ -300,20 +300,13 @@ bool rtl92ce_rx_query_desc(struct ieee80211_hw *hw,
rx_status->flag |= RX_FLAG_MACTIME_START;
- /* hw will set stats->decrypted true, if it finds the
- * frame is open data frame or mgmt frame.
- * So hw will not decryption robust management frame
- * for IEEE80211w but still set status->decrypted
- * true, so here we should set it back to undecrypted
- * for IEEE80211w frame, and mac80211 sw will help
- * to decrypt it
- */
+ /* SWDEC is clear for plaintext too; mac80211 decrypts robust mgmt */
if (stats->decrypted) {
- if ((_ieee80211_is_robust_mgmt_frame(hdr)) &&
- (ieee80211_has_protected(hdr->frame_control)))
- rx_status->flag &= ~RX_FLAG_DECRYPTED;
- else
+ if (ieee80211_has_protected(hdr->frame_control) &&
+ !_ieee80211_is_robust_mgmt_frame(hdr))
rx_status->flag |= RX_FLAG_DECRYPTED;
+ else
+ rx_status->flag &= ~RX_FLAG_DECRYPTED;
}
/* rate_idx: index of data rate into band's
* supported rates or MCS index if HT rates
--
2.56.1
next parent reply other threads:[~2026-11-21 16:36 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20261121163547.37019-1-enderaoelyther@gmail.com>
2026-11-21 16:35 ` Zhao Li [this message]
2026-11-21 16:35 ` [PATCH rtw-next 2/3] wifi: rtlwifi: rtl8192se: don't mark unencrypted frames as decrypted Zhao Li
2026-11-21 16:35 ` [PATCH rtw-next 3/3] wifi: rtlwifi: rtl8192cu: don't mark undecrypted " Zhao Li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261121163547.37019-2-enderaoelyther@gmail.com \
--to=enderaoelyther@gmail.com \
--cc=alexbestoso@gmail.com \
--cc=hemanth.selam@gmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-wireless@vger.kernel.org \
--cc=pkshih@realtek.com \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox