Re: stable v6.6.24 regression: boot fails: bisected to "x86/mpparse: Register APIC address only once"

Wolfgang Walter
2024-04-05T10:51:10Z

Am 2024-04-05 11:33, schrieb Thomas Gleixner:
> On Thu, Apr 04 2024 at 17:57, Greg Kroah-Hartman wrote:
>> On Thu, Apr 04, 2024 at 02:07:11PM +0200, Wolfgang Walter wrote:
>>> Reverting this commit in v6.6.24 solves the problem.
>>
>> Is this also an issue in 6.9-rc1 or newer or 6.8.3 or newer?
>
> Also can you please provide the boot dmesg from a working kernel?
>
> Thanks,
>
> tglx

here dmesg of 6.9-rc1 (which works fine):

[ 0.000000] Linux version 6.9.0-rc1 (S-kernel@sid-i386) (gcc (Debian
13.2.0-23) 13.2.0, GNU ld (GNU Binutils for Debian) 2.42) #1
PREEMPT_DYNAMIC Fri Apr 5 12:12:01 CEST 2024
[ 0.000000] Disabled fast string operations
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff]
usable
[ 0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000003fefffff]
usable
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed13000-0x00000000fed19fff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff]
reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffb00000-0x00000000ffffffff]
reserved
[ 0.000000] Notice: NX (Execute Disable) protection cannot be
enabled: non-PAE kernel!
[ 0.000000] APIC: Static calls initialized
[ 0.000000] SMBIOS 2.3 present.
[ 0.000000] DMI: To Be Filled By O.E.M. To Be Filled By O.E.M./To be
filled by O.E.M., BIOS 080012 10/16/2008
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 999.965 MHz processor
[ 0.011044] e820: update [mem 0x00000000-0x00000fff] usable ==>
reserved
[ 0.011055] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.011070] last_pfn = 0x3ff00 max_arch_pfn = 0x100000
[ 0.011087] MTRR map: 7 entries (5 fixed + 2 variable; max 21), built
from 8 variable MTRRs
[ 0.011093] x86/PAT: PAT not supported by the CPU.
[ 0.011099] x86/PAT: Configuration [0-7]: WB WT UC- UC WB WT UC-
UC
[ 0.011283] Warning only 887MB will be used.
[ 0.011286] Use a HIGHMEM enabled kernel.
[ 0.024443] found SMP MP-table at [mem 0x000ff780-0x000ff78f]
[ 0.024462] initial memory mapped: [mem 0x00000000-0x023fffff]
[ 0.024545] RAMDISK: [mem 0x3a593000-0x3fefffff]
[ 0.024550] Allocated new RAMDISK: [mem 0x31e91000-0x377fdc20]
[ 0.184495] Move RAMDISK from [mem 0x3a593000-0x3feffc20] to [mem
0x31e91000-0x377fdc20]
[ 0.184522] ACPI: Early table checksum verification disabled
[ 0.185291] ACPI BIOS Error (bug): A valid RSDP was not found
(20230628/tbxfroot-222)
[ 0.185316] Intel MultiProcessor Specification v1.4
[ 0.185319] Virtual Wire compatibility mode.
[ 0.185324] MPTABLE: OEM ID: Intel
[ 0.185328] MPTABLE: Product ID: Alviso
[ 0.185330] MPTABLE: APIC at: 0xFEE00000
[ 0.185338] 887MB LOWMEM available.
[ 0.185341] mapped low ram: 0 - 377fe000
[ 0.185344] low ram: 0 - 377fe000
[ 0.185351] Zone ranges:
[ 0.185353] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.185361] Normal [mem 0x0000000001000000-0x00000000377fdfff]
[ 0.185367] Movable zone start for each node
[ 0.185369] Early memory node ranges
[ 0.185371] node 0: [mem 0x0000000000001000-0x000000000009efff]
[ 0.185376] node 0: [mem 0x0000000000100000-0x000000003fefffff]
[ 0.185382] Initmem setup node 0 [mem
0x0000000000001000-0x000000003fefffff]
[ 0.185411] On node 0, zone DMA: 1 pages in unavailable ranges
[ 0.185693] On node 0, zone DMA: 97 pages in unavailable ranges
[ 0.201157] On node 0, zone Normal: 2 pages in unavailable ranges
[ 0.201181] Reserving Intel graphics memory at [mem
0x3ff00000-0x3fffffff]
[ 0.201466] Intel MultiProcessor Specification v1.4
[ 0.201472] Virtual Wire compatibility mode.
[ 0.201477] MPTABLE: OEM ID: Intel
[ 0.201480] MPTABLE: Product ID: Alviso
[ 0.201482] MPTABLE: APIC at: 0xFEE00000
[ 0.201488] Processor #0 (Bootup-CPU)
[ 0.201504] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI
0-23
[ 0.201517] Processors: 1
[ 0.201521] CPU topo: Max. logical packages: 1
[ 0.201524] CPU topo: Max. logical dies: 1
[ 0.201527] CPU topo: Max. dies per package: 1
[ 0.201529] CPU topo: Max. threads per core: 1
[ 0.201535] CPU topo: Num. cores per package: 1
[ 0.201538] CPU topo: Num. threads per package: 1
[ 0.201540] CPU topo: Allowing 1 present CPUs plus 0 hotplug CPUs
[ 0.201570] [mem 0x40000000-0xdfffffff] available for PCI devices
[ 0.201581] clocksource: refined-jiffies: mask: 0xffffffff
max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[ 0.201658] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.201673] pcpu-alloc: [0] 0
[ 0.201697] Kernel command line: BOOT_IMAGE=kernel initrd=system.gz
init=/sbin/init ipv6.disable=1 dummy.numdummies=16 ide-core.nodma=1.0
iommu=pt libata.dma=3 random.trust_cpu=on reboot=cold,force retbleed=off
[ 0.202541] Unknown kernel command line parameters
"BOOT_IMAGE=kernel", will be passed to user space.
[ 0.203023] Dentry cache hash table entries: 131072 (order: 7, 524288
bytes, linear)
[ 0.203310] Inode-cache hash table entries: 65536 (order: 6, 262144
bytes, linear)
[ 0.203384] Built 1 zonelists, mobility grouping on. Total pages:
225008
[ 0.203394] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.219384] Checking if this processor honours the WP bit even in
supervisor mode...Ok.
[ 0.219411] Memory: 789208K/908912K available (12921K kernel code,
739K rwdata, 3076K rodata, 632K init, 280K bss, 119704K reserved, 0K
cma-reserved)
[ 0.265600] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1,
Nodes=1
[ 0.266886] Dynamic Preempt: full
[ 0.267261] rcu: Preemptible hierarchical RCU implementation.
[ 0.267267] Trampoline variant of Tasks RCU enabled.
[ 0.267270] Tracing variant of Tasks RCU enabled.
[ 0.267272] rcu: RCU calculated value of scheduler-enlistment delay
is 30 jiffies.
[ 0.267287] RCU Tasks: Setting shift to 0 and lim to 1
rcu_task_cb_adjust=1.
[ 0.267295] RCU Tasks Trace: Setting shift to 0 and lim to 1
rcu_task_cb_adjust=1.
[ 0.267304] NR_IRQS: 2304, nr_irqs: 48, preallocated irqs: 16
[ 0.267620] rcu: srcu_init: Setting srcu_struct sizes based on
contention.
[ 0.272009] Console: colour VGA+ 80x25
[ 0.272020] printk: legacy console [tty0] enabled
[ 0.278176] APIC: Switch to symmetric I/O mode setup
[ 0.278312] ExtINT not setup in hardware but reported by MP table
[ 0.278804] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=0 pin2=0
[ 0.294846] clocksource: tsc-early: mask: 0xffffffffffffffff
max_cycles: 0x1cd3ebf4f53, max_idle_ns: 881590451058 ns
[ 0.294970] Calibrating delay loop (skipped), value calculated using
timer frequency.. 2000.26 BogoMIPS (lpj=3333216)
[ 0.295096] Disabled fast string operations
[ 0.295183] CPU0: Thermal monitoring enabled (TM1)
[ 0.295295] Last level iTLB entries: 4KB 128, 2MB 0, 4MB 2
[ 0.295368] Last level dTLB entries: 4KB 128, 2MB 0, 4MB 8, 1GB 0
[ 0.295445] CPU: Intel(R) Celeron(R) M processor 1.00GHz
(family: 0x6, model: 0xd, stepping: 0x8)
[ 0.295554] Spectre V1 : Mitigation: usercopy/swapgs barriers and
__user pointer sanitization
[ 0.295655] Spectre V2 : Mitigation: Retpolines
[ 0.295720] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling
RSB on context switch
[ 0.295815] Spectre V2 : Spectre v2 / SpectreRSB : Filling RSB on
VMEXIT
[ 0.295905] Speculative Store Bypass: Vulnerable
[ 0.295972] L1TF: Kernel not compiled for PAE. No mitigation for L1TF
[ 0.296043] MDS: Vulnerable: Clear CPU buffers attempted, no
microcode
[ 0.296133] MMIO Stale Data: Unknown: No mitigations
[ 0.296201] x86/fpu: x87 FPU will use FXSAVE
[ 0.297526] pid_max: default: 32768 minimum: 301
[ 0.304402] Mount-cache hash table entries: 2048 (order: 1, 8192
bytes, linear)
[ 0.304509] Mountpoint-cache hash table entries: 2048 (order: 1, 8192
bytes, linear)
[ 0.310412] Performance Events: p6 PMU driver.
[ 0.310502] ... version: 0
[ 0.310565] ... bit width: 32
[ 0.310628] ... generic registers: 2
[ 0.310691] ... value mask: 00000000ffffffff
[ 0.310758] ... max period: 000000007fffffff
[ 0.310825] ... fixed-purpose events: 0
[ 0.310887] ... event mask: 0000000000000003
[ 0.311099] signal: max sigframe size: 1440
[ 0.311261] rcu: Hierarchical SRCU implementation.
[ 0.311332] rcu: Max phase no-delay instances is 1000.
[ 0.524958] devtmpfs: initialized
[ 0.524958] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.524958] futex hash table entries: 256 (order: -1, 3072 bytes,
linear)
[ 0.529440] pinctrl core: initialized pinctrl subsystem
[ 0.530684] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.531926] thermal_sys: Registered thermal governor 'fair_share'
[ 0.531934] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.532010] thermal_sys: Registered thermal governor 'step_wise'
[ 0.532079] thermal_sys: Registered thermal governor 'user_space'
[ 0.532186] cpuidle: using governor ladder
[ 0.534781] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=5
[ 0.534861] PCI: Using configuration type 1 for base access
[ 0.537177] cryptd: max_cpu_qlen set to 1000
[ 0.540234] ACPI: Interpreter disabled.
[ 0.540350] iommu: Default domain type: Passthrough (set via kernel
command line)
[ 0.540820] SCSI subsystem initialized
[ 0.540994] libata version 3.00 loaded.
[ 0.541138] usbcore: registered new interface driver usbfs
[ 0.541227] usbcore: registered new interface driver hub
[ 0.541314] usbcore: registered new device driver usb
[ 0.541510] pps_core: LinuxPPS API ver. 1 registered
[ 0.541578] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
Rodolfo Giometti <giometti@linux.it>
[ 0.541639] PTP clock support registered
[ 0.541731] EDAC MC: Ver: 3.0.0
[ 0.545937] PCI: Probing PCI hardware
[ 0.546008] PCI: root bus 00: using default resources
[ 0.546014] PCI: Probing PCI hardware (bus 00)
[ 0.546064] PCI host bridge to bus 0000:00
[ 0.546131] pci_bus 0000:00: root bus resource [io 0x0000-0xffff]
[ 0.546207] pci_bus 0000:00: root bus resource [mem
0x00000000-0xffffffff]
[ 0.546302] pci_bus 0000:00: No busn resource found for root bus,
will use [bus 00-ff]
[ 0.546422] pci 0000:00:00.0: [8086:2590] type 00 class 0x060000
conventional PCI endpoint
[ 0.546673] pci 0000:00:02.0: [8086:2592] type 00 class 0x030000
conventional PCI endpoint
[ 0.546786] pci 0000:00:02.0: BAR 0 [mem 0xfe680000-0xfe6fffff]
[ 0.546863] pci 0000:00:02.0: BAR 1 [io 0x9c00-0x9c07]
[ 0.546940] pci 0000:00:02.0: BAR 2 [mem 0xd0000000-0xdfffffff pref]
[ 0.547017] pci 0000:00:02.0: BAR 3 [mem 0xfe640000-0xfe67ffff]
[ 0.547111] pci 0000:00:02.0: Video device with shadowed ROM at [mem
0x000c0000-0x000dffff]
[ 0.547335] pci 0000:00:02.1: [8086:2792] type 00 class 0x038000
conventional PCI endpoint
[ 0.547447] pci 0000:00:02.1: BAR 0 [mem 0xfe580000-0xfe5fffff]
[ 0.547702] pci 0000:00:1c.0: [8086:2660] type 01 class 0x060400 PCIe
Root Port
[ 0.548341] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.548416] pci 0000:00:1c.0: bridge window [io 0xa000-0xafff]
[ 0.548490] pci 0000:00:1c.0: bridge window [mem
0xfe700000-0xfe7fffff]
[ 0.548605] pci 0000:00:1c.0: enabling Extended Tags
[ 0.548717] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.548934] pci 0000:00:1c.1: [8086:2662] type 01 class 0x060400 PCIe
Root Port
[ 0.549064] pci 0000:00:1c.1: PCI bridge to [bus 02]
[ 0.549136] pci 0000:00:1c.1: bridge window [io 0xb000-0xbfff]
[ 0.549209] pci 0000:00:1c.1: bridge window [mem
0xfe800000-0xfe8fffff]
[ 0.549322] pci 0000:00:1c.1: enabling Extended Tags
[ 0.549433] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.549611] pci 0000:00:1c.2: [8086:2664] type 01 class 0x060400 PCIe
Root Port
[ 0.549740] pci 0000:00:1c.2: PCI bridge to [bus 03]
[ 0.549812] pci 0000:00:1c.2: bridge window [io 0xc000-0xcfff]
[ 0.549885] pci 0000:00:1c.2: bridge window [mem
0xfe900000-0xfe9fffff]
[ 0.549998] pci 0000:00:1c.2: enabling Extended Tags
[ 0.550109] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.550305] pci 0000:00:1c.3: [8086:2666] type 01 class 0x060400 PCIe
Root Port
[ 0.550434] pci 0000:00:1c.3: PCI bridge to [bus 04]
[ 0.550506] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff]
[ 0.550579] pci 0000:00:1c.3: bridge window [mem
0xfea00000-0xfeafffff]
[ 0.550692] pci 0000:00:1c.3: enabling Extended Tags
[ 0.550801] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.550997] pci 0000:00:1d.0: [8086:2658] type 00 class 0x0c0300
conventional PCI endpoint
[ 0.551147] pci 0000:00:1d.0: BAR 4 [io 0x9880-0x989f]
[ 0.551336] pci 0000:00:1d.7: [8086:265c] type 00 class 0x0c0320
conventional PCI endpoint
[ 0.551454] pci 0000:00:1d.7: BAR 0 [mem 0xfe63bc00-0xfe63bfff]
[ 0.551697] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[ 0.551883] pci 0000:00:1e.0: [8086:2448] type 01 class 0x060401
conventional PCI bridge
[ 0.552013] pci 0000:00:1e.0: PCI bridge to [bus 05] (subtractive
decode)
[ 0.552110] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.552183] pci 0000:00:1e.0: bridge window [mem
0xfeb00000-0xfebfffff]
[ 0.552415] pci 0000:00:1f.0: [8086:2641] type 00 class 0x060100
conventional PCI endpoint
[ 0.552610] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[ 0.552625] pci 0000:00:1f.0: quirk: [io 0x0800-0x087f] claimed by
ICH6 ACPI/GPIO/TCO
[ 0.552726] pci 0000:00:1f.0: quirk: [io 0x0480-0x04bf] claimed by
ICH6 GPIO
[ 0.552823] pci 0000:00:1f.0: LPC Generic IO decode 2 PIO at
0a00-0a0f
[ 0.553007] pci 0000:00:1f.1: [8086:266f] type 00 class 0x01018a
conventional PCI endpoint
[ 0.553125] pci 0000:00:1f.1: BAR 0 [io 0x0000-0x0007]
[ 0.553203] pci 0000:00:1f.1: BAR 1 [io 0x0000-0x0003]
[ 0.553279] pci 0000:00:1f.1: BAR 2 [io 0x0000-0x0007]
[ 0.553356] pci 0000:00:1f.1: BAR 3 [io 0x0000-0x0003]
[ 0.553434] pci 0000:00:1f.1: BAR 4 [io 0xffa0-0xffaf]
[ 0.553522] pci 0000:00:1f.1: BAR 0 [io 0x01f0-0x01f7]: legacy IDE
quirk
[ 0.553616] pci 0000:00:1f.1: BAR 1 [io 0x03f6]: legacy IDE quirk
[ 0.553687] pci 0000:00:1f.1: BAR 2 [io 0x0170-0x0177]: legacy IDE
quirk
[ 0.553781] pci 0000:00:1f.1: BAR 3 [io 0x0376]: legacy IDE quirk
[ 0.553976] pci 0000:00:1f.2: [8086:2653] type 00 class 0x01018f
conventional PCI endpoint
[ 0.554093] pci 0000:00:1f.2: BAR 0 [io 0x9800-0x9807]
[ 0.554170] pci 0000:00:1f.2: BAR 1 [io 0x9480-0x9483]
[ 0.554247] pci 0000:00:1f.2: BAR 2 [io 0x9400-0x9407]
[ 0.554323] pci 0000:00:1f.2: BAR 3 [io 0x9080-0x9083]
[ 0.554398] pci 0000:00:1f.2: BAR 4 [io 0x9000-0x900f]
[ 0.554474] pci 0000:00:1f.2: BAR 5 [mem 0xfe63b800-0xfe63bbff]
[ 0.554579] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.554737] pci 0000:00:1f.3: [8086:266a] type 00 class 0x0c0500
conventional PCI endpoint
[ 0.554899] pci 0000:00:1f.3: BAR 4 [io 0x0400-0x041f]
[ 0.555197] pci 0000:01:00.0: [8086:109a] type 00 class 0x020000 PCIe
Endpoint
[ 0.555331] pci 0000:01:00.0: BAR 0 [mem 0xfe7e0000-0xfe7fffff]
[ 0.555437] pci 0000:01:00.0: BAR 2 [io 0xac00-0xac1f]
[ 0.555658] pci 0000:01:00.0: PME# supported from D0 D3hot
[ 0.555865] pci 0000:01:00.0: disabling ASPM on pre-1.1 PCIe device.
You can enable it with 'pcie_aspm=force'
[ 0.555997] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.556183] pci 0000:02:00.0: [8086:109a] type 00 class 0x020000 PCIe
Endpoint
[ 0.556314] pci 0000:02:00.0: BAR 0 [mem 0xfe8e0000-0xfe8fffff]
[ 0.556419] pci 0000:02:00.0: BAR 2 [io 0xbc00-0xbc1f]
[ 0.556640] pci 0000:02:00.0: PME# supported from D0 D3hot
[ 0.556844] pci 0000:02:00.0: disabling ASPM on pre-1.1 PCIe device.
You can enable it with 'pcie_aspm=force'
[ 0.556971] pci 0000:00:1c.1: PCI bridge to [bus 02]
[ 0.557136] pci 0000:03:00.0: [8086:109a] type 00 class 0x020000 PCIe
Endpoint
[ 0.557267] pci 0000:03:00.0: BAR 0 [mem 0xfe9e0000-0xfe9fffff]
[ 0.557372] pci 0000:03:00.0: BAR 2 [io 0xcc00-0xcc1f]
[ 0.557593] pci 0000:03:00.0: PME# supported from D0 D3hot
[ 0.557792] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device.
You can enable it with 'pcie_aspm=force'
[ 0.557920] pci 0000:00:1c.2: PCI bridge to [bus 03]
[ 0.558085] pci 0000:04:00.0: [8086:109a] type 00 class 0x020000 PCIe
Endpoint
[ 0.558214] pci 0000:04:00.0: BAR 0 [mem 0xfeae0000-0xfeafffff]
[ 0.558329] pci 0000:04:00.0: BAR 2 [io 0xdc00-0xdc1f]
[ 0.558553] pci 0000:04:00.0: PME# supported from D0 D3hot
[ 0.558759] pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device.
You can enable it with 'pcie_aspm=force'
[ 0.558888] pci 0000:00:1c.3: PCI bridge to [bus 04]
[ 0.558987] pci_bus 0000:05: extended config space not accessible
[ 0.559104] pci 0000:05:02.0: [8086:1229] type 00 class 0x020000
conventional PCI endpoint
[ 0.559223] pci 0000:05:02.0: BAR 0 [mem 0xfebff000-0xfebfffff]
[ 0.559304] pci 0000:05:02.0: BAR 1 [io 0xec00-0xec3f]
[ 0.559381] pci 0000:05:02.0: BAR 2 [mem 0xfebc0000-0xfebdffff]
[ 0.559487] pci 0000:05:02.0: ROM [mem 0xfebe0000-0xfebeffff pref]
[ 0.559590] pci 0000:05:02.0: supports D1 D2
[ 0.559656] pci 0000:05:02.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.559882] pci 0000:05:03.0: [8086:1229] type 00 class 0x020000
conventional PCI endpoint
[ 0.560002] pci 0000:05:03.0: BAR 0 [mem 0xfebfe000-0xfebfefff]
[ 0.560084] pci 0000:05:03.0: BAR 1 [io 0xe880-0xe8bf]
[ 0.560162] pci 0000:05:03.0: BAR 2 [mem 0xfeba0000-0xfebbffff]
[ 0.560267] pci 0000:05:03.0: ROM [mem 0xfeb90000-0xfeb9ffff pref]
[ 0.560370] pci 0000:05:03.0: supports D1 D2
[ 0.560436] pci 0000:05:03.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.560642] pci 0000:05:04.0: [8086:1229] type 00 class 0x020000
conventional PCI endpoint
[ 0.560761] pci 0000:05:04.0: BAR 0 [mem 0xfebfd000-0xfebfdfff]
[ 0.560842] pci 0000:05:04.0: BAR 1 [io 0xe800-0xe83f]
[ 0.560920] pci 0000:05:04.0: BAR 2 [mem 0xfeb60000-0xfeb7ffff]
[ 0.561025] pci 0000:05:04.0: ROM [mem 0xfeb80000-0xfeb8ffff pref]
[ 0.561130] pci 0000:05:04.0: supports D1 D2
[ 0.561195] pci 0000:05:04.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.561404] pci 0000:05:05.0: [8086:1229] type 00 class 0x020000
conventional PCI endpoint
[ 0.561524] pci 0000:05:05.0: BAR 0 [mem 0xfebfc000-0xfebfcfff]
[ 0.561632] pci 0000:05:05.0: BAR 1 [io 0xe480-0xe4bf]
[ 0.561711] pci 0000:05:05.0: BAR 2 [mem 0xfeb40000-0xfeb5ffff]
[ 0.561817] pci 0000:05:05.0: ROM [mem 0xfeb30000-0xfeb3ffff pref]
[ 0.561920] pci 0000:05:05.0: supports D1 D2
[ 0.561985] pci 0000:05:05.0: PME# supported from D0 D1 D2 D3hot
D3cold
[ 0.562216] pci 0000:00:1e.0: PCI bridge to [bus 05] (subtractive
decode)
[ 0.562322] pci 0000:00:1e.0: bridge window [io 0x0000-0xffff]
(subtractive decode)
[ 0.562421] pci 0000:00:1e.0: bridge window [mem
0x00000000-0xffffffff] (subtractive decode)
[ 0.562549] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to
05
[ 0.562710] pci 0000:00:1f.0: PIIX/ICH IRQ router [8086:2641]
[ 0.562792] PCI: pci_cache_line_size set to 64 bytes
[ 0.562880] e820: reserve RAM buffer [mem 0x0009fc00-0x0009ffff]
[ 0.562888] e820: reserve RAM buffer [mem 0x3ff00000-0x3fffffff]
[ 0.563020] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 0.563097] pci 0000:00:02.0: vgaarb: bridge control possible
[ 0.563166] pci 0000:00:02.0: vgaarb: VGA device added:
decodes=io+mem,owns=io+mem,locks=none
[ 0.564971] vgaarb: loaded
[ 0.565627] clocksource: hpet: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 133484882848 ns
[ 0.565743] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.565821] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 0.569359] clocksource: Switched to clocksource tsc-early
[ 0.573946] VFS: Disk quotas dquot_6.6.0
[ 0.574257] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096
bytes)
[ 0.574450] pnp: PnP ACPI: disabled
[ 0.580471] NET: Registered PF_INET protocol family
[ 0.580783] IP idents hash table entries: 16384 (order: 5, 131072
bytes, linear)
[ 0.582635] tcp_listen_portaddr_hash hash table entries: 1024 (order:
0, 4096 bytes, linear)
[ 0.582758] Table-perturb hash table entries: 65536 (order: 6, 262144
bytes, linear)
[ 0.582859] TCP established hash table entries: 8192 (order: 3, 32768
bytes, linear)
[ 0.583006] TCP bind hash table entries: 8192 (order: 4, 65536 bytes,
linear)
[ 0.583210] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.583373] UDP hash table entries: 512 (order: 1, 8192 bytes,
linear)
[ 0.583688] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes,
linear)
[ 0.584231] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.584346] NET: Registered PF_XDP protocol family
[ 0.584437] pci 0000:00:1c.0: bridge window [mem
0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000 add_align
100000
[ 0.584557] pci 0000:00:1c.1: bridge window [mem
0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000 add_align
100000
[ 0.584670] pci 0000:00:1c.2: bridge window [mem
0x00100000-0x000fffff 64bit pref] to [bus 03] add_size 200000 add_align
100000
[ 0.584781] pci 0000:00:1c.3: bridge window [mem
0x00100000-0x000fffff 64bit pref] to [bus 04] add_size 200000 add_align
100000
[ 0.584916] pci 0000:00:1c.0: bridge window [mem
0x40000000-0x401fffff 64bit pref]: assigned
[ 0.585019] pci 0000:00:1c.1: bridge window [mem
0x40200000-0x403fffff 64bit pref]: assigned
[ 0.585119] pci 0000:00:1c.2: bridge window [mem
0x40400000-0x405fffff 64bit pref]: assigned
[ 0.585220] pci 0000:00:1c.3: bridge window [mem
0x40600000-0x407fffff 64bit pref]: assigned
[ 0.585325] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.585396] pci 0000:00:1c.0: bridge window [io 0xa000-0xafff]
[ 0.585472] pci 0000:00:1c.0: bridge window [mem
0xfe700000-0xfe7fffff]
[ 0.585568] pci 0000:00:1c.0: bridge window [mem
0x40000000-0x401fffff 64bit pref]
[ 0.585670] pci 0000:00:1c.1: PCI bridge to [bus 02]
[ 0.585739] pci 0000:00:1c.1: bridge window [io 0xb000-0xbfff]
[ 0.585814] pci 0000:00:1c.1: bridge window [mem
0xfe800000-0xfe8fffff]
[ 0.585909] pci 0000:00:1c.1: bridge window [mem
0x40200000-0x403fffff 64bit pref]
[ 0.586011] pci 0000:00:1c.2: PCI bridge to [bus 03]
[ 0.586079] pci 0000:00:1c.2: bridge window [io 0xc000-0xcfff]
[ 0.586154] pci 0000:00:1c.2: bridge window [mem
0xfe900000-0xfe9fffff]
[ 0.586250] pci 0000:00:1c.2: bridge window [mem
0x40400000-0x405fffff 64bit pref]
[ 0.586352] pci 0000:00:1c.3: PCI bridge to [bus 04]
[ 0.586420] pci 0000:00:1c.3: bridge window [io 0xd000-0xdfff]
[ 0.586495] pci 0000:00:1c.3: bridge window [mem
0xfea00000-0xfeafffff]
[ 0.587304] pci 0000:00:1c.3: bridge window [mem
0x40600000-0x407fffff 64bit pref]
[ 0.587410] pci 0000:00:1e.0: PCI bridge to [bus 05]
[ 0.587479] pci 0000:00:1e.0: bridge window [io 0xe000-0xefff]
[ 0.587556] pci 0000:00:1e.0: bridge window [mem
0xfeb00000-0xfebfffff]
[ 0.587658] pci_bus 0000:00: resource 4 [io 0x0000-0xffff]
[ 0.587729] pci_bus 0000:00: resource 5 [mem 0x00000000-0xffffffff]
[ 0.587804] pci_bus 0000:01: resource 0 [io 0xa000-0xafff]
[ 0.587874] pci_bus 0000:01: resource 1 [mem 0xfe700000-0xfe7fffff]
[ 0.587946] pci_bus 0000:01: resource 2 [mem 0x40000000-0x401fffff
64bit pref]
[ 0.588042] pci_bus 0000:02: resource 0 [io 0xb000-0xbfff]
[ 0.588111] pci_bus 0000:02: resource 1 [mem 0xfe800000-0xfe8fffff]
[ 0.588184] pci_bus 0000:02: resource 2 [mem 0x40200000-0x403fffff
64bit pref]
[ 0.588279] pci_bus 0000:03: resource 0 [io 0xc000-0xcfff]
[ 0.588349] pci_bus 0000:03: resource 1 [mem 0xfe900000-0xfe9fffff]
[ 0.588422] pci_bus 0000:03: resource 2 [mem 0x40400000-0x405fffff
64bit pref]
[ 0.588518] pci_bus 0000:04: resource 0 [io 0xd000-0xdfff]
[ 0.588588] pci_bus 0000:04: resource 1 [mem 0xfea00000-0xfeafffff]
[ 0.588660] pci_bus 0000:04: resource 2 [mem 0x40600000-0x407fffff
64bit pref]
[ 0.588757] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
[ 0.588827] pci_bus 0000:05: resource 1 [mem 0xfeb00000-0xfebfffff]
[ 0.588899] pci_bus 0000:05: resource 4 [io 0x0000-0xffff]
[ 0.588969] pci_bus 0000:05: resource 5 [mem 0x00000000-0xffffffff]
[ 0.589113] pci 0000:00:1d.0: PCI->APIC IRQ transform: INT A -> IRQ
23
[ 0.589241] pci 0000:00:1d.7: PCI->APIC IRQ transform: INT A -> IRQ
23
[ 0.616749] pci 0000:00:1d.7: quirk_usb_early_handoff+0x0/0x7b4 took
26869 usecs
[ 0.616930] pci 0000:05:02.0: Firmware left e100 interrupts enabled;
disabling
[ 0.617039] pci 0000:05:03.0: Firmware left e100 interrupts enabled;
disabling
[ 0.617148] pci 0000:05:04.0: Firmware left e100 interrupts enabled;
disabling
[ 0.617255] pci 0000:05:05.0: Firmware left e100 interrupts enabled;
disabling
[ 0.617353] PCI: CLS 64 bytes, default 64
[ 0.618461] Trying to unpack rootfs image as initramfs...
[ 0.620263] platform rtc_cmos: registered platform RTC device (no PNP
device found)
[ 0.620698] PCLMULQDQ-NI instructions are not detected.
[ 0.621945] Initialise system trusted keyrings
[ 0.622052] Key type blacklist registered
[ 0.626783] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.626892] zbud: loaded
[ 0.897703] NET: Registered PF_ALG protocol family
[ 0.897818] Key type asymmetric registered
[ 0.897884] Asymmetric key parser 'x509' registered
[ 0.897950] Asymmetric key parser 'pkcs8' registered
[ 0.900111] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 250)
[ 0.900222] io scheduler mq-deadline registered
[ 0.900288] io scheduler kyber registered
[ 0.900583] io scheduler bfq registered
[ 0.901244] xz_dec_test: module loaded
[ 0.901313] xz_dec_test: Create a device node with 'mknod xz_dec_test
c 249 0' and write .xz files to it.
[ 0.901625] pcieport 0000:00:1c.0: PCI->APIC IRQ transform: INT A ->
IRQ 16
[ 0.903581] pcieport 0000:00:1c.1: PCI->APIC IRQ transform: INT B ->
IRQ 17
[ 0.903836] pcieport 0000:00:1c.2: PCI->APIC IRQ transform: INT C ->
IRQ 18
[ 0.904089] pcieport 0000:00:1c.3: PCI->APIC IRQ transform: INT D ->
IRQ 19
[ 0.905756] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.950115] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud =
115200) is a 16550A
[ 0.954043] intel_rng: FWH not detected
[ 0.970344] brd: module loaded
[ 0.977815] loop: module loaded
[ 0.980350] ahci 0000:00:1f.2: version 3.0
[ 0.980390] ahci 0000:00:1f.2: PCI->APIC IRQ transform: INT B -> IRQ
19
[ 0.980570] ahci 0000:00:1f.2: forcing PORTS_IMPL to 0xf
[ 0.980764] ahci 0000:00:1f.2: AHCI vers 0001.0000, 32 command slots,
1.5 Gbps, IDE mode
[ 0.980868] ahci 0000:00:1f.2: 4/4 ports implemented (port mask 0xf)
[ 0.980940] ahci 0000:00:1f.2: flags: 64bit ncq pm led pmp slum part
[ 0.987006] scsi host0: ahci
[ 0.987923] scsi host1: ahci
[ 0.988543] scsi host2: ahci
[ 0.989193] scsi host3: ahci
[ 0.989433] ata1: SATA max UDMA/133 abar m1024@0xfe63b800 port
0xfe63b900 irq 19 lpm-pol 0
[ 0.989540] ata2: SATA max UDMA/133 abar m1024@0xfe63b800 port
0xfe63b980 irq 19 lpm-pol 0
[ 0.989638] ata3: SATA max UDMA/133 abar m1024@0xfe63b800 port
0xfe63ba00 irq 19 lpm-pol 0
[ 0.989735] ata4: SATA max UDMA/133 abar m1024@0xfe63b800 port
0xfe63ba80 irq 19 lpm-pol 0
[ 0.990000] ata_piix 0000:00:1f.1: version 2.13
[ 0.990038] ata_piix 0000:00:1f.1: PCI->APIC IRQ transform: INT A ->
IRQ 18
[ 0.994410] scsi host4: ata_piix
[ 0.995439] scsi host5: ata_piix
[ 0.995634] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0
irq 14 lpm-pol 0
[ 0.995734] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8
irq 15 lpm-pol 0
[ 1.009487] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com
for information.
[ 1.009604] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld
<Jason@zx2c4.com>. All Rights Reserved.
[ 1.009711] MACsec IEEE 802.1AE
[ 1.018561] tun: Universal TUN/TAP device driver, 1.6
[ 1.026915] e100: Intel(R) PRO/100 Network Driver
[ 1.027002] e100: Copyright(c) 1999-2006 Intel Corporation
[ 1.027169] e100 0000:05:02.0: PCI->APIC IRQ transform: INT A -> IRQ
16
[ 1.087030] e100 0000:05:02.0 eth0: addr 0xfebff000, irq 16, MAC addr
00:04:a7:0a:03:34
[ 1.087256] e100 0000:05:03.0: PCI->APIC IRQ transform: INT A -> IRQ
17
[ 1.140370] e100 0000:05:03.0 eth1: addr 0xfebfe000, irq 17, MAC addr
00:04:a7:0a:03:35
[ 1.140588] e100 0000:05:04.0: PCI->APIC IRQ transform: INT A -> IRQ
18
[ 1.160414] ata5.01: CFA: TRANSCEND, 20080820, max UDMA/66
[ 1.160513] ata5.01: 15662304 sectors, multi 0: LBA
[ 1.194258] e100 0000:05:04.0 eth2: addr 0xfebfd000, irq 18, MAC addr
00:04:a7:0a:03:36
[ 1.194481] e100 0000:05:05.0: PCI->APIC IRQ transform: INT A -> IRQ
19
[ 1.247364] e100 0000:05:05.0 eth3: addr 0xfebfc000, irq 19, MAC addr
00:04:a7:0a:03:37
[ 1.247569] e1000: Intel(R) PRO/1000 Network Driver
[ 1.247640] e1000: Copyright (c) 1999-2006 Intel Corporation.
[ 1.247767] e1000e: Intel(R) PRO/1000 Network Driver
[ 1.247834] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 1.247979] e1000e 0000:01:00.0: PCI->APIC IRQ transform: INT A ->
IRQ 16
[ 1.248202] e1000e 0000:01:00.0: Interrupt Throttling Rate (ints/sec)
set to dynamic conservative mode
[ 1.306756] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.306886] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.354230] e1000e 0000:01:00.0 eth4: (PCI Express:2.5GT/s:Width x1)
00:04:a7:08:c5:b4
[ 1.354353] e1000e 0000:01:00.0 eth4: Intel(R) PRO/1000 Network
Connection
[ 1.354517] e1000e 0000:01:00.0 eth4: MAC: 2, PHY: 2, PBA No:
FFFFFF-0FF
[ 1.354702] e1000e 0000:02:00.0: PCI->APIC IRQ transform: INT A ->
IRQ 17
[ 1.354926] e1000e 0000:02:00.0: Interrupt Throttling Rate (ints/sec)
set to dynamic conservative mode
[ 1.467667] e1000e 0000:02:00.0 eth5: (PCI Express:2.5GT/s:Width x1)
00:04:a7:08:c5:b5
[ 1.467790] e1000e 0000:02:00.0 eth5: Intel(R) PRO/1000 Network
Connection
[ 1.467954] e1000e 0000:02:00.0 eth5: MAC: 2, PHY: 2, PBA No:
FFFFFF-0FF
[ 1.468138] e1000e 0000:03:00.0: PCI->APIC IRQ transform: INT A ->
IRQ 18
[ 1.468366] e1000e 0000:03:00.0: Interrupt Throttling Rate (ints/sec)
set to dynamic conservative mode
[ 1.581384] e1000e 0000:03:00.0 eth6: (PCI Express:2.5GT/s:Width x1)
00:04:a7:08:c5:b6
[ 1.581511] e1000e 0000:03:00.0 eth6: Intel(R) PRO/1000 Network
Connection
[ 1.581676] e1000e 0000:03:00.0 eth6: MAC: 2, PHY: 2, PBA No:
FFFFFF-0FF
[ 1.581861] e1000e 0000:04:00.0: PCI->APIC IRQ transform: INT A ->
IRQ 19
[ 1.582109] e1000e 0000:04:00.0: Interrupt Throttling Rate (ints/sec)
set to dynamic conservative mode
[ 1.614020] tsc: Refined TSC clocksource calibration: 1000.035 MHz
[ 1.614127] clocksource: tsc: mask: 0xffffffffffffffff max_cycles:
0xe6a38202b4, max_idle_ns: 440795212232 ns
[ 1.614239] clocksource: Switched to clocksource tsc
[ 1.694304] e1000e 0000:04:00.0 eth7: (PCI Express:2.5GT/s:Width x1)
00:04:a7:08:c5:b7
[ 1.694426] e1000e 0000:04:00.0 eth7: Intel(R) PRO/1000 Network
Connection
[ 1.694590] e1000e 0000:04:00.0 eth7: MAC: 2, PHY: 2, PBA No:
FFFFFF-0FF
[ 1.694787] igb: Intel(R) Gigabit Ethernet Network Driver
[ 1.694859] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 1.694974] Intel(R) 2.5G Ethernet Linux Driver
[ 1.695039] Copyright(c) 2018 Intel Corporation.
[ 1.695135] ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver
[ 1.695207] ixgbe: Copyright (c) 1999-2016 Intel Corporation.
[ 1.695741] i40e: Intel(R) Ethernet Connection XL710 Network Driver
[ 1.695823] i40e: Copyright (c) 2013 - 2019 Intel Corporation.
[ 1.696061] sky2: driver version 1.30
[ 1.697546] PPP generic driver version 2.4.2
[ 1.698168] PPP BSD Compression module registered
[ 1.698242] PPP Deflate Compression module registered
[ 1.698310] NET: Registered PF_PPPOX protocol family
[ 1.698404] PPTP driver version 0.8.5
[ 1.701079] uhci_hcd 0000:00:1d.0: PCI->APIC IRQ transform: INT A ->
IRQ 23
[ 1.701232] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 1.701471] ehci-pci 0000:00:1d.7: PCI->APIC IRQ transform: INT A ->
IRQ 23
[ 1.701899] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned
bus number 1
[ 1.702052] uhci_hcd 0000:00:1d.0: irq 23, io port 0x00009880
[ 1.702763] hub 1-0:1.0: USB hub found
[ 1.702854] hub 1-0:1.0: 2 ports detected
[ 1.704774] ehci-pci 0000:00:1d.7: EHCI Host Controller
[ 1.705229] ehci-pci 0000:00:1d.7: new USB bus registered, assigned
bus number 2
[ 1.705364] ehci-pci 0000:00:1d.7: debug port 1
[ 1.707473] usbcore: registered new interface driver usb-storage
[ 1.707825] i8042: PNP: No PS/2 controller found.
[ 1.707892] i8042: Probing ports directly.
[ 1.714921] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.715063] ehci-pci 0000:00:1d.7: irq 23, io mem 0xfe63bc00
[ 1.715235] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 1.716149] mousedev: PS/2 mouse device common for all mice
[ 1.716867] rtc_cmos rtc_cmos: registered as rtc0
[ 1.716984] rtc_cmos rtc_cmos: setting system clock to
2024-04-05T10:44:26 UTC (1712313866)
[ 1.717205] rtc_cmos rtc_cmos: alarms up to one day, 114 bytes nvram,
hpet irqs
[ 1.717660] i2c_dev: i2c /dev entries driver
[ 1.721521] hid: raw HID events driver (C) Jiri Kosina
[ 1.721671] usbcore: registered new interface driver usbhid
[ 1.721743] usbhid: USB HID core driver
[ 1.721866] GACT probability on
[ 1.721949] Mirror/redirect action on
[ 1.722028] Simple TC action Loaded
[ 1.722531] netem: version 1.3
[ 1.722642] u32 classifier
[ 1.722702] Performance counters on
[ 1.722763] input device check on
[ 1.722824] Actions configured
[ 1.723515] xt_time: kernel timezone is -0000
[ 1.723842] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 1.724217] i801_smbus 0000:00:1f.3: PCI->APIC IRQ transform: INT B
-> IRQ 19
[ 1.724357] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[ 1.727386] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[ 1.728080] hub 2-0:1.0: USB hub found
[ 1.728222] hub 2-0:1.0: 2 ports detected
[ 1.728804] hub 1-0:1.0: USB hub found
[ 1.729288] gre: GRE over IPv4 demultiplexor driver
[ 1.729363] ip_gre: GRE over IPv4 tunneling driver
[ 1.729757] hub 1-0:1.0: 2 ports detected
[ 1.735716] IPv4 over IPsec tunneling driver
[ 1.736224] Initializing XFRM netlink socket
[ 1.736314] IPsec XFRM device driver
[ 1.736388] IPv6: Loaded, but administratively disabled, reboot
required to enable
[ 1.736484] IPv6: ah6_init: can't add xfrm type
[ 1.737442] IPv6: esp6_init: can't add xfrm type
[ 1.737509] IPv6: ipcomp6_init: can't add xfrm type
[ 1.745348] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 1.745755] ip6_gre: GRE over IPv6 tunneling driver
[ 1.746196] NET: Registered PF_PACKET protocol family
[ 1.746278] NET: Registered PF_KEY protocol family
[ 1.746391] Bridge firewalling registered
[ 1.747571] NET: Registered PF_KCM protocol family
[ 1.747764] l2tp_core: L2TP core driver, V2.0
[ 1.747840] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.747905] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 1.747986] l2tp_netlink: L2TP netlink interface
[ 1.748089] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 1.748159] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 1.748440] 8021q: 802.1Q VLAN Support v1.8
[ 1.751499] microcode: Current revision: 0x00000000
[ 1.780052] sched_clock: Marking stable (1766683546,
10637291)->(1782065924, -4745087)
[ 1.787675] Loading compiled-in X.509 certificates
[ 1.801719] Key type .fscrypt registered
[ 1.801808] Key type fscrypt-provisioning registered
[ 1.977379] usb 2-1: new high-speed USB device number 2 using
ehci-pci
[ 2.007360] ata2: failed to resume link (SControl 0)
[ 2.007466] ata2: SATA link down (SStatus 0 SControl 0)
[ 2.007560] ata4: failed to resume link (SControl 0)
[ 2.007637] ata4: SATA link down (SStatus 0 SControl 0)
[ 2.014675] scsi 4:0:1:0: Direct-Access ATA TRANSCEND
0820 PQ: 0 ANSI: 5
[ 2.015504] sd 4:0:1:0: [sda] 15662304 512-byte logical blocks: (8.02
GB/7.47 GiB)
[ 2.015640] sd 4:0:1:0: [sda] Write Protect is off
[ 2.015710] sd 4:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 2.015740] sd 4:0:1:0: [sda] Write cache: disabled, read cache:
enabled, doesn't support DPO or FUA
[ 2.015878] sd 4:0:1:0: [sda] Preferred minimum I/O size 512 bytes
[ 2.019446] sda: sda1
[ 2.019921] sd 4:0:1:0: [sda] Attached SCSI disk
[ 2.024502] sd 4:0:1:0: Attached scsi generic sg0 type 0
[ 2.127200] usb-storage 2-1:1.0: USB Mass Storage device detected
[ 2.127715] scsi host6: usb-storage 2-1:1.0
[ 2.404060] usb 1-2: new low-speed USB device number 2 using uhci_hcd
[ 2.660713] input: HID 046a:0011 as
/devices/pci0000:00/0000:00:1d.0/usb1/1-2/1-2:1.0/0003:046A:0011.0001/input/input2
[ 2.724338] hid-generic 0003:046A:0011.0001: input,hidraw0: USB HID
v1.11 Keyboard [HID 046a:0011] on usb-0000:00:1d.0-2/input0
[ 3.134868] scsi 6:0:0:0: Direct-Access Kingston DataTraveler 2.0
1.00 PQ: 0 ANSI: 2
[ 3.135709] sd 6:0:0:0: Attached scsi generic sg1 type 0
[ 3.138335] sd 6:0:0:0: [sdb] 2007040 512-byte logical blocks: (1.03
GB/980 MiB)
[ 3.139098] sd 6:0:0:0: [sdb] Write Protect is off
[ 3.139181] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 3.139853] sd 6:0:0:0: [sdb] No Caching mode page found
[ 3.139937] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[ 3.147229] sdb: sdb1
[ 3.147571] sd 6:0:0:0: [sdb] Attached SCSI removable disk
[ 7.764790] Freeing initrd memory: 91572K
[ 7.855862] Key type encrypted registered
[ 7.856266] gtp: GTP module loaded (pdp ctx size 60 bytes)
[ 7.856513] clk: Disabling unused clocks
[ 7.857122] Freeing unused kernel image (initmem) memory: 632K
[ 7.857773] Write protecting kernel text and read-only data: 16000k
[ 7.857865] rodata_test: all tests were successful
[ 7.857942] Run /init as init process
[ 7.858004] with arguments:
[ 7.858007] /init
[ 7.858010] with environment:
[ 7.858013] HOME=/
[ 7.858017] TERM=linux
[ 7.858020] BOOT_IMAGE=kernel
[ 12.323994] random: crng init done

--
Wolfgang Walter
Studierendenwerk München Oberbayern
Anstalt des öffentlichen Rechts