From: "Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>
To: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Jiri Slaby <jirislaby@kernel.org>,
u.kleine-koenig@pengutronix.de, shawnguo@kernel.org,
s.hauer@pengutronix.de, mcoquelin.stm32@gmail.com,
alexandre.torgue@foss.st.com, cniedermaier@dh-electronics.com,
hugo@hugovil.com, LKML <linux-kernel@vger.kernel.org>,
linux-serial <linux-serial@vger.kernel.org>,
LinoSanfilippo@gmx.de, Lukas Wunner <lukas@wunner.de>,
p.rosenberger@kunbus.com, stable@vger.kernel.org
Subject: Re: [PATCH v5 7/7] serial: 8250_exar: Set missing rs485_supported flag
Date: Wed, 13 Dec 2023 12:18:50 +0200 (EET) [thread overview]
Message-ID: <acca4f3e-2763-655-9968-bbaa9920d289@linux.intel.com> (raw)
In-Reply-To: <20231209125836.16294-8-l.sanfilippo@kunbus.com>
[-- Attachment #1: Type: text/plain, Size: 2001 bytes --]
On Sat, 9 Dec 2023, Lino Sanfilippo wrote:
> The UART supports an auto-RTS mode in which the RTS pin is automatically
> activated during transmission. So mark this mode as being supported even
> if RTS is not controlled by the driver but the UART.
>
> Also the serial core expects now at least one of both modes rts-on-send or
> rts-after-send to be supported. This is since during sanitization
> unsupported flags are deleted from a RS485 configuration set by userspace.
> However if the configuration ends up with both flags unset, the core prints
> a warning since it considers such a configuration invalid (see
> uart_sanitize_serial_rs485()).
>
> Cc: stable@vger.kernel.org
> Signed-off-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
> ---
> drivers/tty/serial/8250/8250_exar.c | 5 +++--
> 1 file changed, 3 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c
> index 6085d356ad86..23366f868ae3 100644
> --- a/drivers/tty/serial/8250/8250_exar.c
> +++ b/drivers/tty/serial/8250/8250_exar.c
> @@ -480,7 +480,7 @@ static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termio
> }
>
> static const struct serial_rs485 generic_rs485_supported = {
> - .flags = SER_RS485_ENABLED,
> + .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND,
> };
>
> static const struct exar8250_platform exar8250_default_platform = {
> @@ -524,7 +524,8 @@ static int iot2040_rs485_config(struct uart_port *port, struct ktermios *termios
> }
>
> static const struct serial_rs485 iot2040_rs485_supported = {
> - .flags = SER_RS485_ENABLED | SER_RS485_RX_DURING_TX | SER_RS485_TERMINATE_BUS,
> + .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND |
> + SER_RS485_RX_DURING_TX | SER_RS485_TERMINATE_BUS,
> };
>
> static const struct property_entry iot2040_gpio_properties[] = {
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
(I assume you picked the correct flag among the two alternatives).
--
i.
prev parent reply other threads:[~2023-12-13 10:18 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20231209125836.16294-1-l.sanfilippo@kunbus.com>
2023-12-09 12:58 ` [PATCH v5 1/7] serial: Do not hold the port lock when setting rx-during-tx GPIO Lino Sanfilippo
2023-12-11 10:35 ` Ilpo Järvinen
2023-12-13 22:14 ` Lino Sanfilippo
2023-12-11 14:49 ` Hugo Villeneuve
2023-12-09 12:58 ` [PATCH v5 2/7] serial: core: set missing supported flag for RX during TX GPIO Lino Sanfilippo
2023-12-11 10:36 ` Ilpo Järvinen
2023-12-09 12:58 ` [PATCH v5 3/7] serial: core: fix sanitizing check for RTS settings Lino Sanfilippo
2023-12-11 10:40 ` Ilpo Järvinen
2023-12-09 12:58 ` [PATCH v5 4/7] serial: core: make sure RS485 cannot be enabled when it is not supported Lino Sanfilippo
2023-12-11 10:53 ` Ilpo Järvinen
2023-12-13 22:23 ` Lino Sanfilippo
2023-12-09 12:58 ` [PATCH v5 5/7] serial: core, imx: do not set RS485 enabled if " Lino Sanfilippo
2023-12-11 11:00 ` Ilpo Järvinen
2023-12-13 22:31 ` Lino Sanfilippo
2023-12-14 9:27 ` Ilpo Järvinen
2023-12-09 12:58 ` [PATCH v5 6/7] serial: omap: do not override settings for RS485 support Lino Sanfilippo
2023-12-13 10:26 ` Ilpo Järvinen
2023-12-13 22:55 ` Lino Sanfilippo
2023-12-09 12:58 ` [PATCH v5 7/7] serial: 8250_exar: Set missing rs485_supported flag Lino Sanfilippo
2023-12-13 10:18 ` Ilpo Järvinen [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=acca4f3e-2763-655-9968-bbaa9920d289@linux.intel.com \
--to=ilpo.jarvinen@linux.intel.com \
--cc=LinoSanfilippo@gmx.de \
--cc=alexandre.torgue@foss.st.com \
--cc=cniedermaier@dh-electronics.com \
--cc=gregkh@linuxfoundation.org \
--cc=hugo@hugovil.com \
--cc=jirislaby@kernel.org \
--cc=l.sanfilippo@kunbus.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=lukas@wunner.de \
--cc=mcoquelin.stm32@gmail.com \
--cc=p.rosenberger@kunbus.com \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
--cc=stable@vger.kernel.org \
--cc=u.kleine-koenig@pengutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox