[U-Boot-Users] Doubt on Kernel Linking

[Rupesh S <rupeshs@myw.ltindia.com>]

I also enabled the DEBUG printfs in u-boot.
Below attached is the log of messages I got after displaying memory of
"log_buf".
It gives a few "OOPS".
The kernel mesages must be happening before the kernel gets hold of serial
console as well, because I don't see these on my console.

:>bootm 100000
## Booting image at 00100000 ...
   Image Name:   Rupesh's Kernel Image
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    489707 Bytes = 478.2 kB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
## Current stack ends at 0x0075FC18 => set upper limit to 0x0075F410
## cmdline at 0x0075F310 ... 0x0075F310
bd address  = 0x0075FFC4
memstart    = 0x00000000
memsize     = 0x00800000
flashstart  = 0x02800000
flashsize   = 0x00200000
flashoffset = 0x00080000
sramstart   = 0x00000000
sramsize    = 0x00000000
immr_base   = 0xFF000000
bootflags   = 0x00000001
intfreq     =     40 MHz
busfreq     =     40 MHz
ethaddr     = 08:00:22:50:70:63
IP addr     = 192.168.6.227
baudrate    =  19200 bps
No initrd
## Transferring control to Linux (at address 00000000) ...

/****************** Here It Hanged !!! *****************/
/***************** Below messages after  RESET ************************/


U-Boot 0.3.1 (May 26 2003 - 11:20:21)

CPU:   PPC823ZTnnA at 40 MHz: 2 kB I-Cache 1 kB D-Cache
         *** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: FADS with db MPC823 rev ENG or PILOT
DRAM:  (4 MB SDRAM)  8 MB
Top of RAM usable for U-Boot at: 00800000
Reserving 512k for U-Boot at: 00780000
Reserving 128k for malloc() at: 00760000
Reserving 60 Bytes for Board Info at: 0075ffc4
Reserving 44 Bytes for Global Data at: 0075ff98
Stack Pointer at: 0075ff78
New Stack Pointer is: 0075ff78
Now running in RAM - U-Boot at: 00780000
FLASH:  2 MB
In:    serial
Out:   serial
Err:   serial
U-Boot relocated to 00780000
Net:   SCC ETHERNET
### main_loop entered: bootdelay=0

### main_loop: bootcmd="<UNDEFINED>"

/********************* The location of "log_buf"
*****************************************/
:>md 12eee8
0012eee8: 63657373 206f6620 62616420 61726561    cess of bad area
0012eef8: 2c207369 673a2031 310a4f6f 70733a20    , sig: 11.Oops:
0012ef08: 6b65726e 656c2061 63636573 73206f66    kernel access of
0012ef18: 20626164 20617265 612c2073 69673a20     bad area, sig:
0012ef28: 31310a4f 6f70733a 206b6572 6e656c20    11.Oops: kernel
0012ef38: 61636365 7373206f 66206261 64206172    access of bad ar
0012ef48: 65612c20 7369673a 2031310a 3c323e4b    ea, sig: 11.<2>K
0012ef58: 65726e65 6c207374 61636b20 6f766572    ernel stack over
0012ef68: 666c6f77 20696e20 70726f63 65737320    flow in process
0012ef78: 63303131 37303230 2c207231 3d633031    c0117020, r1=c01
0012ef88: 31373262 300a4f6f 70733a20 6b65726e    172b0.Oops: kern
0012ef98: 656c2061 63636573 73206f66 20626164    el access of bad
0012efa8: 20617265 612c2073 69673a20 31310a4f     area, sig: 11.O
0012efb8: 6f70733a 206b6572 6e656c20 61636365    ops: kernel acce
0012efc8: 7373206f 66206261 64206172 65612c20    ss of bad area,
0012efd8: 7369673a 2031310a 4f6f7073 3a206b65    sig: 11.Oops: ke
:>

What could be wrong  ??
Please advice..
Rupesh

----- Original Message -----
From: "Wolfgang Denk" <wd@denx.de>
To: "Rupesh S" <rupeshs@myw.ltindia.com>
Cc: <u-boot-users@lists.sourceforge.net>
Sent: Friday, May 23, 2003 6:56 AM
Subject: Re: [U-Boot-Users] Doubt on Kernel Linking


> In message <00a901c3219b$59d821d0$6706a8c0@SPLENDOR> you wrote:
> >
> > I kept the link address back at 0xc0000000.
> > Doing mkimage , I did load address and entry address as 0x0.
> >
> > On my FADS823 board, I do a download to 0x100000.
> > And gave a bootm 0x100000.
> >
> > But the system hangs after Uncompressing Kernel Image...
> > Note: I have compared the bd_info stricture of linux and u-boot . It is
the
> > same . Also the IMMR address.
> > I do mkimage on gzipped binary image of vmlinux.
> >
> > Please advice.
>
> Attach a debugger (BDI2000 recommended).
>
> Or reset the board and check the contents  of  the  "log_buf"  buffer
> (post  mortem  dump) - grep the address from the System.map file, and
> subtract 0xC0000000 to convert from virtual to physical address;  the
> use U-Boot's "md" command.
>
> Best regards,
>
> Wolfgang Denk
>
> --
> Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
> Phone: (+49)-8142-4596-87  Fax: (+49)-8142-4596-88  Email: wd at denx.de
> If all economists were laid end to end, they would not reach  a  con-
> clusion.