From mboxrd@z Thu Jan 1 00:00:00 1970 From: Z.N. Date: Wed, 09 Feb 2005 22:22:01 +0000 Subject: [U-Boot-Users] at45 dataflash In-Reply-To: <20050208233603.C7678C108D@atlas.denx.de> References: <20050208233603.C7678C108D@atlas.denx.de> Message-ID: <1107987721.18080.3.camel@localhost> List-Id: MIME-Version: 1.0 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit To: u-boot@lists.denx.de Hi! Thanks for the reply! This is how u-boot boots for me: U-Boot 1.1.2 (Feb 9 2005 - 16:43:51) U-Boot code: 21F00000 -> 21F16F40 BSS: -> 21F1B5F8 RAM Configuration: Bank #0: 20000000 32 MB Atmel: Flash: 0 kB Error Timeout DataFlash:AT45DB161 Nb pages: 4096 Page Size: 528 Size= 2162688 bytes Logical address: 0xC0000000 Area 0: C0000000 to C0007FFF (RO) Area 1: C0008000 to C001FFFF (RO) Area 2: C0020000 to C0027FFF Area 3: C0028000 to C020FFFF *** Warning - bad CRC, using default environment In: serial Out: serial Err: serial U-Boot> And if I display the contents of the Dataflash, the following happens: U-Boot> md c0000000 c0000000:Error Timeout Error Timeout data abort pc : [<21f08648>] lr : [<21f12310>] sp : 21eddc38 ip : 21edda28 fp : 21eddc7c r10: c0000000 r9 : 00000100 r8 : 21eddfdc r7 : 00000010 r6 : 00000000 r5 : 00000004 r4 : 21eddc48 r3 : 00000000 r2 : fffff200 r1 : 21edda5c r0 : ffffffff Flags: nZCv IRQs off FIQs off Mode SVC_32 Resetting CPU ... How come that the dataflash _gets detected_, however it is not _readable_?! (I only have dataflash no NAND flash..) I've tried to set CFG_MAX_FLASH_BANKS and CFG_MAX_NAND_DEVICE to 0, but this did not help (same as above). How can I remove NAND support from my config? (Maybe that is the cause of the dataflash errors..) I hope Wolfgang or someone could give me a hint (or some pointers to the documentation..) Best regards, Zoli PS: In fact I've also tried to use the Atmel supplied loader.bin to load the u-boot image, with the following results: When the loader.bin image is running on the board, and outputting the 'C' characters, waiting for the Xmodem transfer. Then, the following happens during the Xmodem transfer: sx -X u-boot.bin /dev/ttyS0 Sending u-boot.bin, 728 blocks: Give your local XMODEM receive command now. Xmodem sectors/kbytes sent: 0/ 0kRetry 0: NAK on sector Retry 0: NAK on sector Retry 0: NAK on sector Retry 0: NAK on sector Retry 0: NAK on sector Retry 0: NAK on sector Retry 0: NAK on sector Retry 0: NAK on sector Retry 0: NAK on sector Retry 0: NAK on sector Retry 0: NAK on sector Retry 0: Retry Count Exceeded Transfer incomplete Have anyone experienced such thing? On Wed, 2005-02-09 at 00:35 +0100, Wolfgang Denk wrote: > In message <1107905713.9293.9.camel@localhost> you wrote: > > > > As far as I've looked at the sources, there is a configuration option > > that I can store environment variables on the dataflash, however how can > > I load the kernel image & ramdisk image from dataflash into SDRAM? > > (I've found no commands to do this, maybe I overlooked it somewhere..) > > You use the same commands as for NOR flash. Dataflash support was > intergrated transparently. > > > If there is no way to do this, what if I load the kernel image together > > with u-boot into sdram on startup, can u-boot start this "pre-loaded" > > kernel image? > > In theory it can. [And actually it most probably will.] > > However, you are aware that U-Boot expects to be started fresh out of > reset on a completely uninitialized system, and on such a system you > cannot have any SDRAM contents as the SDRAM has not been initialized > yet. I guess you may want to read the FAQ at > http://www.denx.de/twiki/bin/view/DULG/CanUBootBeConfiguredSuchThatItCanBeStartedInRAM > > Best regards, > > Wolfgang Denk