[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

["André Schwarz" <andre.schwarz@matrix-vision.de>]

Dieter,

On Mon, 2009-06-22 at 14:04 +0200, Dieter Kiermaier wrote:
> Hi all,
> 
> I've tried the first time booting a self compiled u-boot from git.marvell.com 
> U-Boot can be downloaded and started with openocd quite well.
> Boot messages (version is dirty due to a comment in board file):
> 
> U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> Marvell-Sheevaplug
> 
> SoC:   Kirkwood 88F6281_A0
> DRAM:  512 MB
> NAND:  512 MiB
> *** Warning - bad CRC or NAND, using default environment

most propably you'll need to save the environment.

> 
> In:    serial
> Out:   serial
> Err:   serial
> Net:   egiga0
> 88E1116 Initialized on egiga0
> Hit any key to stop autoboot:  0
> Marvell>>

type "save" here and "reset".

> 
> 
> Environment is broken only with marvell git u-boot. Preflashed u-boot find 
> environment is ok.
> Does sheevaplug u-boot from marvell git use other environment settings than 
> preflashed u-boot?
> 
> Marvell>> printenv
> bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs} ${x_bootargs_root}; 
> bootm 0x6400000;
> bootdelay=3
> baudrate=115200
> x_bootargs=console=ttyS0,115200 
> mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs) rw
> x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000
> x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
> stdin=serial
> stdout=serial
> stderr=serial
> ethaddr=00:50:43:e0:b9:d8
> ethact=egiga0
> ipaddr=192.168.2.75
> 
> (ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
> 
> If I now try to ping another machine in the same network:
> Marvell>> ping 192.168.2.251
> Using egiga0 device

maybe your MAC is missing ? environment ?

> 
> 
> 
> This is all what happens - no response from board, CTRL-C doesn't work.
> Only a hard reset will get the board up again.
> 
> Do I have to change something in the default board configuration to 
> succesfullly use networking on the sheevaplug?
> 
> u-boot is build with following commands:
> 
> make ARCH=arm sheevaplug_config
> make
> 
> I get no errors during build.
> 
> My gcc version is:
> arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
> 
> Any help would be appreciated,
> Dieter
> 
> 
Regards,

Andr??
> 
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot



MATRIX VISION GmbH, Talstra?e 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Gesch?ftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich