[U-Boot-Users] Intel Flash CFI initialisation failure

[Mirek23 <miroslaw.dach@psi.ch>]

Dear All,

            I am having the problem with Intel Flash TE28F640 J3C120 on my
avnet evaluation board
(xilinx based with Virtex-4). I have compiled successfully u-boot-1.2.0 and
it run well without FLASH support. Eventually I want to store u-boot in
Flash but when I compile u-boot with Flash support the u-boot fails during
Flash initialization.

My Flash memory is:
type:    TE28F640 J3C120 
(http://www.datasheets.org.uk/datasheet.php?article=3266188) 
vendor: Intel
spec:    NOR FLASH 64 Blocks 64 Mbits x8/x16
 

To support Flash memory I have configured u-boot with the following
settings:
#define CFG_FLASH_BASE                     0xFF800000              
#define CFG_MAX_FLASH_BANKS            1 
#define CFG_MAX_FLASH_SECT              64
#define CFG_FLASH_CFI                        1 
#define CFG_FLASH_CFI_DRIVER             1 
 
The u-boot was compiled successfully but when I booted it I have got the 
error messages when it came to the Flash initialization:

U-Boot 1.2.0 (Sep  6 2007 - 17:56:34)

### No HW ID - assuming ML403
DRAM:  32 MB
Top of RAM usable for U-Boot at: 02000000
Reserving 138k for U-Boot at: 01fdd000
Reserving 129k for malloc() at: 01fbcc00
Reserving 120 Bytes for Board Info at: 01fbcb88
Reserving 48 Bytes for Global Data at: 01fbcb58
Stack Pointer at: 01fbcb38
New Stack Pointer is: 01fbcb38
Now running in RAM - U-Boot at: 01fdd000
FLASH: flash detect cfi
fwc addr ff800000 cmd 0 0 8bit x 8 bit
fwc addr ff800055 cmd 98 98 8bit x 8 bit
is= cmd 51(Q) addr ff800010 is= 0 51
fwc addr ff800555 cmd 98 98 8bit x 8 bit
is= cmd 51(Q) addr ff800010 is= 0 51
fwc addr ff800000 cmd 0 0000 16bit x 8 bit
fwc addr ff8000aa cmd 98 9898 16bit x 8 bit
is= cmd 51(Q) addr ff800020 is= 0051 5151
fwc addr ff800aaa cmd 98 9898 16bit x 8 bit
is= cmd 51(Q) addr ff800020 is= 0051 5151
fwc addr ff800000 cmd 0 0000 16bit x 16 bit
fwc addr ff8000aa cmd 98 0098 16bit x 16 bit
is= cmd 51(Q) addr ff800020 is= 0051 0051
is= cmd 52(R) addr ff800022 is= 0052 0052
is= cmd 59(Y) addr ff800024 is= 0059 0059
ushort addr is at ff800050 info->portwidth = 2
addr[0] = 0x0
addr[1] = 0x2
addr[2] = 0x0
addr[3] = 0x0
retval = 0x2
device interface is 2
found port 2 chip 2 port 16 bits chip 16 bits
ushort addr is at ff800026 info->portwidth = 2
addr[0] = 0x0
addr[1] = 0x1
addr[2] = 0x0
addr[3] = 0x0
retval = 0x1
fwc addr ff800000 cmd ff 00ff 16bit x 16 bit
fwc addr ff800000 cmd 90 0090 16bit x 16 bit
fwc addr ff800000 cmd ff 00ff 16bit x 16 bit
fwc addr ff8000aa cmd 98 0098 16bit x 16 bit
ushort addr is at ff80002a info->portwidth = 2
addr[0] = 0x0
addr[1] = 0x31
addr[2] = 0x0
addr[3] = 0x0
retval = 0x31
ff800020 : 00 51 00 52 00 59 00 01 00 00 00 31 00 00 00 00  .Q.R.Y.....1....
ff800030 : 00 00 00 00 00 00 00 27 00 36 00 00 00 00 00 08  .......'.6......
ff800040 : 00 08 00 0b 00 00 00 02 00 02 00 03 00 00 00 17  ................
ff800050 : 00 02 00 00 00 05 00 00 00 01 00 3f 00 00 00 00  ...........?....
ff800060 : 00 02 00 50 00 52 00 49 00 31 00 31 00 ce 00 00  ...P.R.I.1.1....
ff800070 : 00 00 00 00 00 01 00 01 00 00 00 33 00 00 00 01  ...........3....
ff800080 : 00 80 00 00 00 03 00 03 00 03 00 00 00 00 00 00  ................
ff800090 : ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff  ................
manufacturer is 1
manufacturer id is 0x89
device id is 0x17
device id2 is 0x0
cfi version is 0x3131
size_ratio 1 port 16 bits chip 16 bits
found 1 erase regions
long addr is at ff80005a info->portwidth = 2
addr[0] = 0x0
addr[1] = 0x3f
addr[2] = 0x0
addr[3] = 0x0
addr[4] = 0x0
addr[5] = 0x0
addr[6] = 0x0
addr[7] = 0x2
erase_region_count = 64 erase_region_size = 131072
Bus Fault @ 0x01fe4424, fixup 0x00000000
Machine check in kernel mode.
Caused by (from msr): regs 01fbc978 Data parity signal
NIP: 01FE4424 XER: 20000000 LR: 01FE43D8 REGS: 01fbc978 TRAP: 0200 DAR:
00000000MSR: 00021000 EE: 0 PR: 0 FP: 0 ME: 1 IR/DR: 00

GPR00: 00000000 01FBCA68 C01FC950 01FFF8D0 00000001 01FBCA70 00000001
00000006 
GPR08: 00000000 FFC00004 01FBCA73 00000003 01FBC860 30000000 02001600
00000000 
GPR16: 00020000 00000001 0000002D 00000000 00000020 00000040 0000002D
FFC20000 
GPR24: 01FFF950 00000001 00000020 00000004 01FFF8D0 01FBCB58 02001A94
FFC00000 
Call backtrace: 
machine check
NIP: FFFFFFFC XER: 00000000 LR: 01FED864 REGS: 01fbc868 TRAP: 0700 DAR:
00000001MSR: 00000000 EE: 0 PR: 0 FP: 0 ME: 0 IR/DR: 00


Does anybody have an idea what could be wrong?

Best Regards

Mirek






-- 
View this message in context: http://www.nabble.com/Intel-Flash-CFI-initialisation-failure-tf4400680.html#a12553111
Sent from the Uboot - Users mailing list archive at Nabble.com.