[U-Boot] [PATCH 03/15] powerpc/85xx: Rework P2020DS pci_init_board to use common FSL PCIe code

[Kumar Gala <galak@kernel.crashing.org>]

Remove duplicated code in P2020DS board and utliize the common
fsl_pcie_init_board().  We also now dynamically setup the LAWs for PCI
controllers based on which PCIe controllers are enabled.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
---
 board/freescale/p2020ds/law.c     |    8 +--
 board/freescale/p2020ds/p2020ds.c |  114 ++++---------------------------------
 2 files changed, 12 insertions(+), 110 deletions(-)

diff --git a/board/freescale/p2020ds/law.c b/board/freescale/p2020ds/law.c
index 28ed2ed..91642a9 100644
--- a/board/freescale/p2020ds/law.c
+++ b/board/freescale/p2020ds/law.c
@@ -1,5 +1,5 @@
 /*
- * Copyright 2008-2009 Freescale Semiconductor, Inc.
+ * Copyright 2008-2010 Freescale Semiconductor, Inc.
  *
  * (C) Copyright 2000
  * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
@@ -29,12 +29,6 @@
 
 struct law_entry law_table[] = {
 	SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
-	SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCIE_1),
-	SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_1),
-	SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCIE_2),
-	SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_2),
-	SET_LAW(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_PCIE_3),
-	SET_LAW(CONFIG_SYS_PCIE3_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_3),
 	SET_LAW(PIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_LBC),
 	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
 };
diff --git a/board/freescale/p2020ds/p2020ds.c b/board/freescale/p2020ds/p2020ds.c
index 07b0801..727de69 100644
--- a/board/freescale/p2020ds/p2020ds.c
+++ b/board/freescale/p2020ds/p2020ds.c
@@ -175,113 +175,21 @@ phys_size_t fixed_sdram(void)
 
 #endif
 
-#ifdef CONFIG_PCIE1
-static struct pci_controller pcie1_hose;
-#endif
-
-#ifdef CONFIG_PCIE2
-static struct pci_controller pcie2_hose;
-#endif
+#ifdef CONFIG_PCI
+static const char *slot_names[] = {
+	[PCIE1] = "Slot 2",
+	[PCIE2] = "ULI",
+	[PCIE3] = "Slot 1",
+};
 
-#ifdef CONFIG_PCIE3
-static struct pci_controller pcie3_hose;
-#endif
+const char *board_serdes_name(enum srds_prtcl device)
+{
+	return slot_names[device];
+}
 
-#ifdef CONFIG_PCI
 void pci_init_board(void)
 {
-	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
-	struct fsl_pci_info pci_info[3];
-	u32 devdisr, pordevsr, io_sel;
-	int first_free_busno = 0;
-	int num = 0;
-
-	int pcie_ep, pcie_configured;
-
-	devdisr = in_be32(&gur->devdisr);
-	pordevsr = in_be32(&gur->pordevsr);
-	io_sel = (pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
-
-	debug ("   pci_init_board: devdisr=%x, io_sel=%x\n", devdisr, io_sel);
-
-	puts("\n");
-#ifdef CONFIG_PCIE2
-	pcie_configured = is_serdes_configured(PCIE2);
-
-	if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE2)) {
-		SET_STD_PCIE_INFO(pci_info[num], 2);
-		pcie_ep = fsl_setup_hose(&pcie2_hose, pci_info[num].regs);
-		printf("PCIE2: connected to ULI as %s (base addr %lx)\n",
-			pcie_ep ? "Endpoint" : "Root Complex",
-			pci_info[num].regs);
-		first_free_busno = fsl_pci_init_port(&pci_info[num++],
-					&pcie2_hose, first_free_busno);
-
-		/*
-		 * The workaround doesn't work on p2020 because the location
-		 * we try and read isn't valid on p2020, fix this later
-		 */
-#if 0
-		/*
-		 * Activate ULI1575 legacy chip by performing a fake
-		 * memory access.  Needed to make ULI RTC work.
-		 * Device 1d has the first on-board memory BAR.
-		 */
-
-		pci_hose_read_config_dword(hose, PCI_BDF(2, 0x1d, 0),
-				PCI_BASE_ADDRESS_1, &temp32);
-		if (temp32 >= CONFIG_SYS_PCIE3_MEM_BUS) {
-			void *p = pci_mem_to_virt(PCI_BDF(2, 0x1d, 0),
-							temp32, 4, 0);
-			debug(" uli1575 read to %p\n", p);
-			in_be32(p);
-		}
-#endif
-	} else {
-		printf("PCIE2: disabled\n");
-	}
-	puts("\n");
-#else
-	setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE2); /* disable */
-#endif
-
-#ifdef CONFIG_PCIE3
-	pcie_configured = is_serdes_configured(PCIE3);
-
-	if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE3)) {
-		SET_STD_PCIE_INFO(pci_info[num], 3);
-		pcie_ep = fsl_setup_hose(&pcie3_hose, pci_info[num].regs);
-		printf("PCIE3: connected to Slot 1 as %s (base addr %lx)\n",
-			pcie_ep ? "Endpoint" : "Root Complex",
-			pci_info[num].regs);
-		first_free_busno = fsl_pci_init_port(&pci_info[num++],
-					&pcie3_hose, first_free_busno);
-	} else {
-		printf("PCIE3: disabled\n");
-	}
-	puts("\n");
-#else
-	setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE3); /* disable */
-#endif
-
-#ifdef CONFIG_PCIE1
-	pcie_configured = is_serdes_configured(PCIE1);
-
-	if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)) {
-		SET_STD_PCIE_INFO(pci_info[num], 1);
-		pcie_ep = fsl_setup_hose(&pcie1_hose, pci_info[num].regs);
-		printf("PCIE1: connected to Slot 2 as %s (base addr %lx)\n",
-			pcie_ep ? "Endpoint" : "Root Complex",
-			pci_info[num].regs);
-		first_free_busno = fsl_pci_init_port(&pci_info[num++],
-					&pcie1_hose, first_free_busno);
-	} else {
-		printf("PCIE1: disabled\n");
-	}
-	puts("\n");
-#else
-	setbits_be32(&gur->devdisr, MPC85xx_DEVDISR_PCIE); /* disable */
-#endif
+	fsl_pcie_init_board(0);
 }
 #endif
 
-- 
1.6.0.6