From: Kumar Gala <galak@kernel.crashing.org>
To: u-boot@lists.denx.de
Subject: [U-Boot] [PATCH v3 7/8] powerpc/86xx: Convert SBC8641 to use common SRIO init code
Date: Tue, 11 Jan 2011 02:10:35 -0600 [thread overview]
Message-ID: <1294733436-10264-7-git-send-email-galak@kernel.crashing.org> (raw)
In-Reply-To: <1294733436-10264-6-git-send-email-galak@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
---
* Renamed CONFIG_SYS_HAS_SRIO -> CONFIG_SYS_SRIO
board/sbc8641d/law.c | 1 -
include/configs/sbc8641d.h | 15 +++++++++------
2 files changed, 9 insertions(+), 7 deletions(-)
diff --git a/board/sbc8641d/law.c b/board/sbc8641d/law.c
index a6f60ee..14259d6 100644
--- a/board/sbc8641d/law.c
+++ b/board/sbc8641d/law.c
@@ -51,7 +51,6 @@ struct law_entry law_table[] = {
#endif
SET_LAW(0xf8000000, LAW_SIZE_2M, LAW_TRGT_IF_LBC),
SET_LAW(0xfe000000, LAW_SIZE_32M, LAW_TRGT_IF_LBC),
- SET_LAW(CONFIG_SYS_RIO_MEM_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_RIO)
};
int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
index 90d84eb..8d9f931 100644
--- a/include/configs/sbc8641d.h
+++ b/include/configs/sbc8641d.h
@@ -57,6 +57,9 @@
*/
#define CONFIG_SYS_SCRATCH_VA 0xe8000000
+#define CONFIG_SYS_SRIO
+#define CONFIG_SRIO1 /* SRIO port 1 */
+
#define CONFIG_PCI 1 /* Enable PCIE */
#define CONFIG_PCIE1 1 /* PCIE controler 1 (slot 1) */
#define CONFIG_PCIE2 1 /* PCIE controler 2 (slot 2) */
@@ -297,9 +300,9 @@
/*
* RapidIO MMU
*/
-#define CONFIG_SYS_RIO_MEM_BASE 0xc0000000 /* base address */
-#define CONFIG_SYS_RIO_MEM_PHYS CONFIG_SYS_RIO_MEM_BASE
-#define CONFIG_SYS_RIO_MEM_SIZE 0x20000000 /* 128M */
+#define CONFIG_SYS_SRIO1_MEM_BASE 0xc0000000 /* base address */
+#define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_BASE
+#define CONFIG_SYS_SRIO1_MEM_SIZE 0x20000000 /* 128M */
/*
* General PCI
@@ -417,10 +420,10 @@
* BAT2 512M Cache-inhibited, guarded
* 0xc000_0000 512M RapidIO Memory
*/
-#define CONFIG_SYS_DBAT2L (CONFIG_SYS_RIO_MEM_BASE | BATL_PP_RW \
+#define CONFIG_SYS_DBAT2L (CONFIG_SYS_SRIO1_MEM_BASE | BATL_PP_RW \
| BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CONFIG_SYS_DBAT2U (CONFIG_SYS_RIO_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
-#define CONFIG_SYS_IBAT2L (CONFIG_SYS_RIO_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_DBAT2U (CONFIG_SYS_SRIO1_MEM_BASE | BATU_BL_512M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L (CONFIG_SYS_SRIO1_MEM_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
#define CONFIG_SYS_IBAT2U CONFIG_SYS_DBAT2U
/*
--
1.7.2.3
next prev parent reply other threads:[~2011-01-11 8:10 UTC|newest]
Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-01-06 16:58 [U-Boot] [PATCH 1/7] powerpc/8xxx: Refactor SRIO initialization into common code Kumar Gala
2011-01-06 16:58 ` [U-Boot] [PATCH 2/7] powerpc/85xx: Convert MPC8548CDS to use common SRIO init code Kumar Gala
2011-01-06 16:58 ` [U-Boot] [PATCH 3/7] powerpc/85xx: Convert MPC8568MDS " Kumar Gala
2011-01-06 16:58 ` [U-Boot] [PATCH 4/7] powerpc/85xx: Convert MPC8569MDS " Kumar Gala
2011-01-06 16:58 ` [U-Boot] [PATCH 5/7] powerpc/86xx: Enable " Kumar Gala
2011-01-06 16:58 ` [U-Boot] [PATCH 6/7] powerpc/86xx: Convert MPC8641HPCN to use " Kumar Gala
2011-01-06 16:58 ` [U-Boot] [PATCH 7/7] powerpc/86xx: Convert SBC8641 " Kumar Gala
2011-01-06 19:34 ` Paul Gortmaker
2011-01-11 6:54 ` Kumar Gala
2011-01-11 6:54 ` [U-Boot] [PATCH 6/7] powerpc/86xx: Convert MPC8641HPCN " Kumar Gala
2011-01-09 12:53 ` [U-Boot] [PATCH 5/7] powerpc/86xx: Enable " Sergei Shtylyov
2011-01-09 21:16 ` [U-Boot] [PATCH v2 1/7] powerpc/8xxx: Refactor SRIO initialization into common code Kumar Gala
2011-01-09 21:16 ` [U-Boot] [PATCH v2 5/7] powerpc/86xx: Enable common SRIO init code Kumar Gala
2011-01-11 6:54 ` Kumar Gala
2011-01-11 6:53 ` [U-Boot] [PATCH v2 1/7] powerpc/8xxx: Refactor SRIO initialization into common code Kumar Gala
2011-01-11 7:09 ` Wolfgang Denk
2011-01-11 8:11 ` Kumar Gala
2011-01-11 8:10 ` [U-Boot] [PATCH v3 1/8] " Kumar Gala
2011-01-11 8:10 ` [U-Boot] [PATCH v3 2/8] powerpc/85xx: Convert MPC8548CDS to use common SRIO init code Kumar Gala
2011-01-11 8:10 ` [U-Boot] [PATCH v3 3/8] powerpc/85xx: Convert MPC8568MDS " Kumar Gala
2011-01-11 8:10 ` [U-Boot] [PATCH v3 4/8] powerpc/85xx: Convert MPC8569MDS " Kumar Gala
2011-01-11 8:10 ` [U-Boot] [PATCH v3 5/8] powerpc/86xx: Enable " Kumar Gala
2011-01-11 8:10 ` [U-Boot] [PATCH v3 6/8] powerpc/86xx: Convert MPC8641HPCN to use " Kumar Gala
2011-01-11 8:10 ` Kumar Gala [this message]
2011-01-11 8:10 ` [U-Boot] [PATCH v3 8/8] powerpc/85xx: Add SRIO support to P2020DS Kumar Gala
2011-01-11 14:14 ` Kumar Gala
2011-01-11 14:14 ` [U-Boot] [PATCH v3 7/8] powerpc/86xx: Convert SBC8641 to use common SRIO init code Kumar Gala
2011-01-11 14:14 ` [U-Boot] [PATCH v3 6/8] powerpc/86xx: Convert MPC8641HPCN " Kumar Gala
2011-01-11 14:13 ` [U-Boot] [PATCH v3 5/8] powerpc/86xx: Enable " Kumar Gala
2011-01-11 14:13 ` [U-Boot] [PATCH v3 4/8] powerpc/85xx: Convert MPC8569MDS to use " Kumar Gala
2011-01-11 14:13 ` [U-Boot] [PATCH v3 3/8] powerpc/85xx: Convert MPC8568MDS " Kumar Gala
2011-01-11 14:13 ` [U-Boot] [PATCH v3 2/8] powerpc/85xx: Convert MPC8548CDS " Kumar Gala
2011-01-11 9:46 ` [U-Boot] [PATCH v3 1/8] powerpc/8xxx: Refactor SRIO initialization into common code Wolfgang Denk
2011-01-11 14:13 ` Kumar Gala
2011-01-11 6:54 ` [U-Boot] [PATCH 4/7] powerpc/85xx: Convert MPC8569MDS to use common SRIO init code Kumar Gala
2011-01-11 6:54 ` [U-Boot] [PATCH 3/7] powerpc/85xx: Convert MPC8568MDS " Kumar Gala
2011-01-11 6:54 ` [U-Boot] [PATCH 2/7] powerpc/85xx: Convert MPC8548CDS " Kumar Gala
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1294733436-10264-7-git-send-email-galak@kernel.crashing.org \
--to=galak@kernel.crashing.org \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox