[U-Boot] [PATCH v3 07/12] OMAP3 SPL: Rework memory initalization and devkit8000 support

[Tom Rini <trini@ti.com>]

This changes to making the board be responsible for providing the
memory initialization timings in SPL and converts the devkit8000
to this framework.  In SPL we try and initialize both CS0 and CS1.

Cc: Frederik Kriewitz <frederik@kriewitz.eu>
Signed-off-by: Tom Rini <trini@ti.com>
---
 arch/arm/cpu/armv7/omap3/sdrc.c             |   28 ++++++++++++++------------
 arch/arm/include/asm/arch-omap3/mem.h       |   26 -------------------------
 arch/arm/include/asm/arch-omap3/sys_proto.h |    2 +
 board/timll/devkit8000/devkit8000.c         |   21 ++++++++++++++++++++
 include/configs/devkit8000.h                |    4 ---
 5 files changed, 38 insertions(+), 43 deletions(-)

diff --git a/arch/arm/cpu/armv7/omap3/sdrc.c b/arch/arm/cpu/armv7/omap3/sdrc.c
index 2756024..a27b4b1 100644
--- a/arch/arm/cpu/armv7/omap3/sdrc.c
+++ b/arch/arm/cpu/armv7/omap3/sdrc.c
@@ -148,6 +148,18 @@ void do_sdrc_init(u32 cs, u32 early)
 	sdrc_actim_base0 = (struct sdrc_actim *)SDRC_ACTIM_CTRL0_BASE;
 	sdrc_actim_base1 = (struct sdrc_actim *)SDRC_ACTIM_CTRL1_BASE;
 
+	/*
+	 * When called in the early context this may be SPL and we will
+	 * need to set all of the timings.  This ends up being board
+	 * specific so we call a helper function to take care of this
+	 * for us.  Otherwise, to be safe, we need to copy the settings
+	 * from the first bank to the second.  We will setup CS0,
+	 * then set cs_cfg to the appropriate value then try and
+	 * setup CS1.
+	 */
+#ifdef CONFIG_SPL_BUILD
+	get_board_mem_timings(&mcfg, &ctrla, &ctrlb, &rfr_ctrl, &mr);
+#endif
 	if (early) {
 		/* reset sdrc controller */
 		writel(SOFTRESET, &sdrc_base->sysconfig);
@@ -164,22 +176,12 @@ void do_sdrc_init(u32 cs, u32 early)
 
 		writel(ENADLL | DLLPHASE_90, &sdrc_base->dlla_ctrl);
 		sdelay(0x20000);
-/* As long as V_MCFG and V_RFR_CTRL is not defined for all OMAP3 boards we need
- * to prevent this to be build in non-SPL build */
 #ifdef CONFIG_SPL_BUILD
-		/*
-		 * If we use a SPL there is no x-loader nor config header so
-		 * we have to do the job ourselfs
-		 */
-
-		mcfg = V_MCFG;
-		ctrla = V_ACTIMA_165;
-		ctrlb = V_ACTIMB_165;
-		rfr_ctrl = V_RFR_CTRL;
-		mr = V_MR;
-
 		write_sdrc_timings(CS0, sdrc_actim_base0, mcfg, ctrla, ctrlb,
 				rfr_ctrl, mr);
+		make_cs1_contiguous();
+		write_sdrc_timings(CS0, sdrc_actim_base1, mcfg, ctrla, ctrlb,
+				rfr_ctrl, mr);
 #endif
 
 	}
diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
index 4d69c94..775c989 100644
--- a/arch/arm/include/asm/arch-omap3/mem.h
+++ b/arch/arm/include/asm/arch-omap3/mem.h
@@ -195,32 +195,6 @@ enum {
 		ACTIM_CTRLB(NUMONYX_TWTR_165, NUMONYX_TCKE_165,	\
 				NUMONYX_TXP_165, NUMONYX_XSR_165)
 
-#ifdef CONFIG_OMAP3_INFINEON_DDR
-#define V_ACTIMA_165		INFINEON_V_ACTIMA_165
-#define V_ACTIMB_165		INFINEON_V_ACTIMB_165
-#endif
-
-#ifdef CONFIG_OMAP3_MICRON_DDR
-#define V_ACTIMA_165		MICRON_V_ACTIMA_165
-#define V_ACTIMB_165		MICRON_V_ACTIMB_165
-#define V_MCFG			MICRON_V_MCFG_165
-#define V_RFR_CTRL		SDP_3430_SDRC_RFR_CTRL_165MHz
-#define V_MR			MICRON_V_MR_165
-#endif
-
-#ifdef CONFIG_OMAP3_NUMONYX_DDR
-#define V_ACTIMA_165		NUMONYX_V_ACTIMA_165
-#define V_ACTIMB_165		NUMONYX_V_ACTIMB_165
-#endif
-
-#if !defined(V_ACTIMA_165) || !defined(V_ACTIMB_165)
-#error "Please choose the right DDR type in config header"
-#endif
-
-#if defined(CONFIG_SPL_BUILD) && (!defined(V_MCFG) || !defined(V_RFR_CTRL))
-#error "Please choose the right DDR type in config header"
-#endif
-
 /*
  * GPMC settings -
  * Definitions is as per the following format
diff --git a/arch/arm/include/asm/arch-omap3/sys_proto.h b/arch/arm/include/asm/arch-omap3/sys_proto.h
index 9e64410..80e167b 100644
--- a/arch/arm/include/asm/arch-omap3/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap3/sys_proto.h
@@ -38,6 +38,8 @@ void per_clocks_enable(void);
 void memif_init(void);
 void sdrc_init(void);
 void do_sdrc_init(u32, u32);
+void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
+		u32 *mr);
 void emif4_init(void);
 void gpmc_init(void);
 void enable_gpmc_cs_config(const u32 *gpmc_config, struct gpmc_cs *cs, u32 base,
diff --git a/board/timll/devkit8000/devkit8000.c b/board/timll/devkit8000/devkit8000.c
index fee0dff..af9233e 100644
--- a/board/timll/devkit8000/devkit8000.c
+++ b/board/timll/devkit8000/devkit8000.c
@@ -138,3 +138,24 @@ int board_eth_init(bd_t *bis)
 	return dm9000_initialize(bis);
 }
 #endif
+
+/*
+ * Routine: get_board_mem_timings
+ * Description: If we use SPL then there is no x-loader nor config header
+ * so we have to setup the DDR timings ourself on the first bank.  This
+ * provides the timing values back to the function that configures
+ * the memory.
+ */
+void get_board_mem_timings(u32 *mcfg, u32 *ctrla, u32 *ctrlb, u32 *rfr_ctrl,
+		u32 *mr)
+{
+	/* General SDRC config */
+	*mcfg = MICRON_V_MCFG_165;
+	*rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
+
+	/* AC timings */
+	*ctrla = MICRON_V_ACTIMA_165;
+	*ctrlb = MICRON_V_ACTIMB_165;
+
+	*mr = MICRON_V_MR_165;
+}
diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
index 6c51a27..d29481e 100644
--- a/include/configs/devkit8000.h
+++ b/include/configs/devkit8000.h
@@ -68,10 +68,6 @@
 #define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + (128 << 10))
 
 /* Hardware drivers */
-
-/* DDR - I use Micron DDR */
-#define CONFIG_OMAP3_MICRON_DDR		1
-
 /* DM9000 */
 #define CONFIG_NET_RETRY_COUNT		20
 #define	CONFIG_DRIVER_DM9000		1
-- 
1.7.0.4